SPECIAL REPAIR TO BUILDING NO T-65 AND MINOR WORK FOR WASHING POINT AT REASI UNDER AGE(I) REASI

Amount

B/R Work :- Demolition of brickwork or stone/ boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete, all as specified and directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water, complete, all as specified and directed.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n.exc 4 Sqm each including cutting holes for taking out hold fasts, dismentaling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost), complete, all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises, complete, all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level), complete, all as specified and directed.

Dismantling of wall and ceiling boards (fibre pulp insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete, all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6, complete, all as specified and directed.

M&L 10 mm thick rendering on fair faces of brick/concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement, complete, all as specified and directed.

M&L 15 mm thick rendering on other than fair faces of brick/stone masonry surfaces in cement mortar 1:4 and finished even and smooth without using extra cement, complete, all as specified and directed. Note: WPC will be measured and paid seperately

Supply only integral water proofing compound conforming to latest IS specifications.

Preparation of newly plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of 1mm thick birla white putty, complete, all as specified and directed.

Preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a priming coat of alkali resistant paint including necessary base preparaion, complete, all as specified and directed.

Preparation of old plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of 1mm thick birla white putty, complete, all as specified and directed.

Preparation of old plastered surfaces of wall and applying two coats of cement base paint over a priming coat of alkali resistant paint including necessary base preparaion, complete, all as specified and directed.

S&F factory made pressed steel door frames 1.25mm thick PBI sheet with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate etc. complete, of frame size 125 x 60 mm, including tarring with ends and back of chowkhats and lugs including back filling of PCC 1:3:6 for chowkhats & PCC 1:2:4 for block for hold fast and also painting with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete, all as specified and directed.

S&F 35 mm thick factory made, 2nd class hard wood, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, complete, all as specified and directed.

S&F 2nd class hard wood glazed and skeleton shutters, 35mm thick open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and itred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, complete, all as specified and directed.

S&F steel windows / ventilator with tubular frame factory made with double shutter (wire gauged shutter and glass / glazed shutter, (wire cloth and glass panes shall be measured and paid separately) of size 79 mm x 39 mm, 16 gauge rectangular tubular frame with side hung shutter with glazing bars 12 x 3 mm flat iron including box type hinges with steel handle and steel peg stay dovetailed or welded including 2 Nos tower bolts 100 mm long and 10 mm square bar grills complete, twlo coats of synthetic enamel paint over one coat of red oxide primer including taking down old windows / ventilators all as specified and as shouwn on drg CEUZ/TD/1269/2008 HT 1/1 to 1/3 Note: Wire cloth and glass panes will measured and paid speperately.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube and fixed in opening as per specification in SSR-II, complete, all as specified and directed.

S&F factory made solid PVC moulded door shutter (particle board core), 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete, all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with wooden beads/glazing pin in squares not exceeding 0.50 Sqm in each pane, complete, all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,140mm overall length of cover plate fixed in floor complete all as specified and directed.

S & F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.0mm and fixed with tinned tacks, or galvanised wire staples, complete, all as specified and directed.

S&F Aluminium handles cast type, anodised, 150 mm size, complete, all as specified and directed.

S&F mild steel cold rolled butt hinges medium weight 100 mm long, complete, all as specified and directed.

S&F Aluminium alloy, sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete, all as specified and directed.

S&F Aluminium anodised barrel tower bolts of extruded section with 200 mm long bolt, complete, all as specified and directed.

S&F mild steel, 300 mm, ordinary rat tail rod pattern door spring including roller and roller plate, complete, all as specified and directed.

Preparation of new wood or wood based surfaces of any discription not otherwise described exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete, all as specified and directed.

M&L non-skid coloured ceramic (square or rectengular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 10mm thick screed bed in CM 1:6 over 25 mm thick PCC 1:2:4 type B-0 complete all as specified and directed.

M&L glazed ceramic tiles in vertical surfaces 350x250x7mm/450x350x7mm thick set set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface incl 10 MM thick screed bed in CM 1:4, complete, all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling (Size of grid 605x605mm), complete, all as specified and directed.

S&F 7mm thick designer mineral fibre board ceiling fixed or laid/ inserted in snap grid ceiling , complete, all as specified and directed. Make: Armstrong (beauty sky in white) or equivalent, make and design as approved by Engineer-In-Charge.

S&F in repairs fancy type stainless steel drapery rods 19/20mm bore for curtain rails with fixing stainless steel brackets, fancy stainless steel stops and curtain rings (06 nos per mtr), complete, all as specified and directed.

S&F in repairs 15mm fancy bib taps, cast copper alloy cromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed , complete, all as specified and directed.

S&F in repair in repairs 15 mm bore, CP Stop valves concelaed type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type, chromium plated with long shank and cup , complete, all as specified and directed.

S&F in repairs gratting 125 mm dia with waster hole of PTMT (Min weights 40 gms) , complete, all as specified and directed.

S&F in repairs PVC connections 15mm size 600 mm long as fixed , complete, all as specified and directed.

S&F in repairs CP brass shower rose 125mm of size with or without swivel joints any size including fixing to steel pipe or union as fixed in repair, complete, all as specified and directed.

S&F in repairs pillar tap 15mm cast copper alloy, with capstan head CP, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shank and fly nuts, screwed for iron pipe and fixed, complete, all as specified and directed.

S&F in repair 10 ltr PVC valveless, syphonic action type, flushing cistern, low level, with inlet, ball valve, float and handle including brackets, , complete, all as specified and directed. Make : Parryware Slimline standard or equivalent as approved.

S&F in repairs vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including a provision of concrete bedding, complete, all as specified and directed. Make : Parryware Cat Part No. C0117 or equivalent.

S&F vitreous in repair vitreous china wash basin, white, flat back, size 550x400mm excluding tap, waste pipe of 32mm dia and waste fittings, Pillar tap brass, chromium with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, complete, all as specified and directed.

S&F in repairs tubular towel rail, 20mm dia D type 60cm long between flanges, complete, all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth in any type of soil/strata for foundation, etc, or for shafts, cess pits, manholes, pier holes, wells, drain pipes n.exc 10sqm on plan and n.exc 11.5m in dpeth and getting out in soft / soil complete, all as specified and directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 cum in soft/loose soil, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface, complete, all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick, complete, all as specified and directed.

Removing excavated material to a distance n.exc 50m and deposited where directed at a level not exceeding 1.50 m above the starting point, complete, all as specified and directed.

Hardcore of broken stone or boulders of gauge n ex. 63m and depositing where directed at a level n exc 1.5m above the starting poing complete all as specified and as directed.

M&L providing cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in floor/sub base and finished even and fair, complete, all as specified and directed.

M&L 25mm thick plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair, complete, all as specified and directed.

M&L cement PCC concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregates as in foundation, filling and mass concrete , complete, all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:4, complete, all as specified and directed.

M&L for brick work in CM 1:4 with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete, all as specified and directed.

M&L RCC type B-0 1:2:4 (12.5mm graded crushed stone aggregate) slabs supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, rough finished surface of concrete, complete, all as specified and directed.

Mild steel TMT bars 6 to 8mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips, complete, all as specified and directed.

S&F fancy type bib taps 15mm bore, fancy type, cast copper alloy chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed , complete, all as specified and directed.

S&F steel water tubing of nominal bore 15 mm, medium grade galvanised with all fittings including short lengths, laid in trenches complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) , complete, all as specified and directed.

S&F steel water tubing of nominal bore 20 mm, medium grade galvanised with all fittings including short lengths, laid in trenches complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) , complete, all as specified and directed.

S&F rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 liters including all accessories, complete, all as specified and directed.

M&L MS structural steel work Fe-410-W (Gde-250) quality -B rolled sections as in framing for galzing and the like fixed with angle cleats and connecting plates etc complete all as specified and directed.

S&F gun metal globe or gate valves, with iron wheel head screwed both ends for iron pipe of 20mm bore and fixed, complete, all as specified and directed.

M&L machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete, all as specified and directed.

M&L plain cement concrete 1:3:6 type C-1 using 20 mm graded crushed stone aggregates as in surface channel and drains, complete, all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. all as specified.

S&F ball brass valves , high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule of bore of 20mm, complete, all as specified and directed.

Cutting existing 20mm steel tubing for alterations or additions (each cut measured), complete, all as specified and directed.

Preparation of new painted steel and iron surfaces of any description exceeding 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint over red oxide zinc chrome primer, complete, all as specified and directed.

E/M Work :- Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, sockets brackets, switch boards etc and making good disturbed surfaces of walls, floors etc , complete, all as specified and directed.

M&L for point wiring (surface) for one light / fan point controlled by one, single pole, one way switch, 5 amps with 1.5 sqmm, PVC insulated but unsheathed, multi stranded copper conductor FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher 1.5mm thick complete with all PVC conduit accessories / fittings ISI marked and sunk type pressed steel terminal switch boxes 1.5 mm thick duly painted with black bituminous paint over one coat of red oxide primer with plastic laminated sheet top cover 3mm thick make hylam, brass screws and cup washers including 1.5 Sqmm multi stranded copper conductor PVC insulated green in colour as continuous earth conductor to common earth and connected to earth dolly with all accessories , complete, all as specified and directed. Note:- Rates for cutting chages are included in point wiring. Colour coding must be followed.

All as per item No 2.02 but one 2&3 pin 5 Amp socket outlet on same board.

All as per item No 2.02 but one 2&3 pin 5 Amp switch socket combination on independent board.

All as per item No 2.02 but one 3 pin 5/15 Amp switch socket combination with cable 2.5 sqmm for neutral and live wire and 1.5 sqmm for earth on independent board.

S&F wiring in existing surface/recessed steel/PVC conduit for circuit/submain wiring alongwith for phase and neutral wire of size 2x6.0 Sqmm with 1x4.0 Sqmm as earth wire in green colour of FRLS PVC insulated copper conductor 1100 v grade single core cable including drawn through concealed conduit 20mm dia, complete all as specified and directed.

S&F LED Fluorescent tube light fitting, 1 x 20 W, LED integrated Batten T5 indoor decorative aluminium extruded T5 LED Battens - integrated type white complete with all accessories with twin core twisted flexible copper conductor cable with suitable size, complete all as specified and directed.

S&F 1 X 10 w LED bulk head luminaries, IP 65 LED Bulk Head in engineering plastic housing with clear prismatic diffuser with lamp holders , etc. Complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 V, 50 HZ, complete all as specified and directed.

S&F switch piano 5A flush button type single pole one way, complete all as specified and directed.

S&F polycarbonate ceiling rose surface bakelite 65x50mm, three terminal isolated body fixed on PVC round block, complete, all as specified and directed.

S&F polycarbonate socket outlet 2 in 1, 5 pin, 5 Amp flush type universal, complete all as specified and directed .

S&F polycarbonate socket outlet 2 in 1, 3 pin, 5 and 15 Amp flush type universal, complete all as specified and directed .

S&F switch piano 15A flush button type single pole one way white, complete all as specified and directed.

S&F electronic step type fan regulator 100 watt 230 volts 50 C/S deluxe modular type fixed on existing phenolic laminated sheet suitable for 1200/1400mm ceiling fan, complete all as specified and directed.

S&F lamp holder PVC/polycarbonate type with back plate suitable for batten fitting with new 9 Watt LED lamp, in white colour with Base Cap , complete all as specified.

Supplying and laying or fixing or passing through pipe 1100 volts grade heavy duty cable PVC insulated aluminium Stranded conductor, served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed in service connections of size 16 sqmm 4 core, complete all as specified and directed.

S&F sheet metal enclosure for DBs double door when MCBs to be used TPN with 200 amps rated bus bar 440 V 4 way with MCB as incomer and MCB as outgoing, complete all as specified an directed.

S&F sheet metal enclosure for DBs double door when MCBs to be used SPN with 200 amps rated bus bar 240 V 8 way with bus bar, neutral link earth bar, complete all as specified an directed.

S&F MCB SPN 5 to 40 Amps, 10KA C - curve fixed with suitable lugs, complete all as specified and directed.

S&F MCB SP 5 to 40 Amps, 10KA C - curve fixed with suitable lugs, complete all as specified and directed.

S&F MCB TPN 63 Amps, 10KA fixed with suitable lugs, complete all as specified and directed.

Taking down the existing ceiling fan, refixing dismantling, cleaning greasing oiling and rehanging the same in existing position incluiding making connection with suitable copper cable from ceiling rose or connector to fan, complete all as specified an directed.

M&L rewinding of ceiling fan motor of size 1200mm/1400mm with super enamelled copper winding wire not less than the existing gauge affter cutting and removing the burnt existing winding including varnishing heating by providing fresh insulating materials, complete all as specified and directed.

M&L for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work , complete all as specified and directed.

Design, Supply, installation, testing and commissioning of bus bar chember box of size 0.5Mx0.8Mx0.60M depth,(HxBxD) outdoor type alongwith one incoming MCCB 100 A 4 Pole 25 KA factor fabricated made out of CRCA sheet of 3.15 mm thick, fully enclosed and angle iron frame of size 40 x 40 x 6mm thick and T section with front and rear openable duble door shutter, dust and vermin proof and rear opening complete with locking arrangement, having a system of bus bars of aluminium of suitable size of 100 Amps duly insulated and mounted on Epoxy/porcelain insulators in totally enclosed chamber with three phase and neutral 415 volts, AC, system. provn of suitable cable glands, duly powder coated, complete all as specified and directed.

Note:- Deduction for Schedule of credit (Sch 'A' Part-II) to be made of Rs. 13651.00 from the total quoted amount of BOQ while accepting the bid. Details of schedule of credit is given in tender documents.

Madan Lal Sharma and Sons

M/s Cosmos Builder and Developer

M/S JEEVAN LAL SHARMA

M/s J V Construction

KRISHNA BUILDERS

RAMA CONSTRUCTION COMPANY