SPL REPAIRS AND ROOF TREATMENT TO BLDG NOS PB-56, PB-57 AND PB-58 OF NCO ACADEMY UNDER AGE(I) DHANA AT DHANA MILITARY STATION.

Amount

Demolition of brick work built in cement mortar of any description including quoins, arches but excluding ashlars facing, complete all as specified and directed by the Engr-in-charge.

Material & Labour for brick work with sub class ‘B’ bricks straight or curved on plan exc. 6 mtr mean radius built in CM(1:6), complete all as specified and directed.

Material & Labour for brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4, complete all as specified and directed.

Taking down plaster on brick or concrete surfaces including raking out joints for key and scrubbing down with water etc complete all as specified and directed.

Material & Labour for rendering 15 mm thick on fair faces of brick or concrete the surface even and smooth without using extra cement in CM (1:4) Mixed with water proofing compound @ 3% complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid separately)

Supply only integral water proofing compound complete all as specified and directed.

Material & Labour for rendering 10 mm thick on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement in CM (1:6) complete all as specified and directed.

Material & Labour for 5mm thick rendering in CM (1:3) on concrete surfaces, finished even & smooth (without using extra cement), complete all as specified and directed.

Material & Labour for applying a coat of 1.5 mm thick Birla wall care putty as per manufacture instruction complete all as specified and directed.

Material & Labour for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion complete all as specified and directed.

Material & Labour for complete removal of existing treatment by scrapping, wire brushing from old walls and applying two coats of oil bound distemper including preparation of surfaces complete all as specified and directed.

Material & Labour for preparing new plaster surfaces walls including chajjas, facias etc including filling of holes and applying 1.5 mm thick wall care putty as per manufacturer's instructions and applying two coat of weather proof acrylic exterior paint (100% Acrylic) over a coat of primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

Material & Labour for complete removal of existing finish on walls including chajjas, facias etc. including filling of holes and applying 1.5 mm thick wall care putty as per manufacturer's instructions and applying two coat of weather proof acrylic exterior paint (100% Acrylic) over a coat of primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

Material & Labour for preparation of old decorated plastered surfaces of ceiling including cornices, pilasters etc and applying two coat of white wash complete all as specified and directed.

Material & Labour for preparation of new plastered surfaces of ceiling including cornices, pilasters etc and applying three coat of white wash complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Material & Labour for Non-skid ceramic colour tiles7 to 8 mm thick, (square/rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed.

Material & Labour for Non Skid ceramic colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed.

Material & Labour Glazed ceramic colour tiles of size 300 x 450 x7mm thick on vertical wall etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 complete as specified and directed.

Taking down chowket or frame exc 1.50 sqm but n. exc. 4.00 sqm with shutters (without taking of shutter from frame) etc complete all as specified and directed.

Taking down chowket or frame n.exc 1.50 sqm with shutters (without taking of shutter from frame) etc complete all as specified and directed.

Supply & fixing 125 x 60 mm size Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

Supply & fixing 105 x 60 mm size Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

Material & Labour for cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate for fixing hold fast, coping, cills and filling in pressed steel door frames including necessary form work and finishing the surfaces to match with existing, complete all as specified and directed.

Material & Labour for 2nd class hard wood factory made 35mm thick plain framed panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fixing 2nd class HW 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares (without sash bars ), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats. complete all as specified and directed.

Supply and fixing factory solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with MS Square tube as per specified & drawing in opening complete all as specified and directed.

Supply and fixing for Factory Made Solid PVC Moulded Door Shutter, 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm Plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face complete all as specified and directed.

Supply & fixing tinted / coloured frosted on one side glass ordinary quality & glazing with wooden/ aluminium bead/oil putty in Square n.exc 0.5 Sqm in Each panel 4.8 mm thick complete all as per specified and directed. Make:- Modiguard/ saintgobin / Hariyana glass

Supply & fixing Sheet glass 4mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each including hacking out old broken glass complete all as specified and directed.

Supply and fixing galvanised steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.8mm and fixed with tinned tacks or galvanized wire staples or wooden bead complete all as specified and directed.

Supply and fixing in repair galvanised steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.8mm and fixed with tinned tacks or galvanized wire staples or wooden bead complete all as specified and directed.

Material & Labour for preparation new or previously untreated surfaces of wood and wood based material of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material & Labour for preparation of old painted wooden surfaces of any description not otherwise described, over 10cm width or girth and applying a coat of synthetic enamel paint complete all as specified and directed.

Material & Labour for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer, complete all as specified and directed.

Supply and fixing framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

Material & Labour for preparation of old steel surfaces and applying one coats of synthetic enamel paint of any description over 10 cm width and girth complete all as specified and directed.

Supply and fixing MS butt hinges of 100 mm size cold rolled mild steel medium weight, ISI marked complete all as specified and directed.

Supply and fixing in repairs MS butt hinges of 100 mm size cold rolled mild steel medium weight, ISI marked complete all as specified and directed.

Supply and fixing for 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed..

Supply and fixing in repair 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

Supply and fixing 125 mm size Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

Supply and fixing in repairs 125 mm size Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

Supply and fixing for 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Supply and fixing in repairs 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Supply and fixing 200mm size mild steel barrel tower bolt stone enamelled black with bright bolt ISI marked complete all as specified and directed.

Supply and fixing in repairs 200mm size mild steel barrel tower bolt stone enamelled black with bright bolt ISI marked complete all as specified and directed.

Supply and fixing for 300mm mild steel, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and as directed.

Supply and fixing in repair 300mm mild steel, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and as directed.

Supply and fixing 150mm size Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

Supply and fixing in repairs 150mm size Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

Supply and fixing in repair vitreous china wash basin white flat back size 550x400mm including pedestal excluding taps, waste, chain and plug and porcelain stopper but including brackets as in repair, complete all as specified and directed.

Supply and fixing in repair brass chromium plated tubular towel rail, 20 mm dia., D Type, 45 cm long between flanges, complete all as specified and directed.

Supply and fixing in repair PVC connection 15mm size with PTMT nuts of length 450mm long complete all as specified and directed.

Supply and fixing in repair Bib taps cast copper chromium plated fancy type with crutch or butterfly handle screwed for iron pipe or for brass ferrule of 15 mm bore dia complete all as specified and directed.

Supply and fixing in repair pillar cock, chromium plated, fancy type for iron pipe or for brass ferrule of 15mm bore dia complete all as specified and directed.

Supply and fixing in repair 15 mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fixing in repair soap dish vitreous china white approximate size 160 x 160 x 90 fixed to plug with chromium plated brass screw complete all as specified and directed.

Supply and fixing 32 mm bore low density polyethylene pipe (LDPE) of pressure rating 6 Kgs/cm2 as in waster pipe for WHB and urinal waste pipe, complete all as specified and directed.

Dismantling unserviceable PVC water storage tank of 500 Ltr capacity, complete all as specified and directed.

Supply and fixing 500 ltr rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with all as specified in SSR Part I complete all as specified and directed.

Supply and fixing in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 210 gms) complete screwed for iron pipe or brass ferrule of size 20 mm bore, complete all as specified and directed.

Supply and fixing in repair wall mixer valve for mixing hot and cold water, cast copper alloy, chromium plated screwed high pressure with long screwed shank and fly nuts for pipe 15/20 mm bore complete all as specified and directed.

Supply and fixing stop valve cast copper alloy, fancy type chromium plated with long shank and cup (concealed type) 15 mm bore, screwed down, high pressure, screwed both end for iron pipe or for union complete all as specified and directed.

Supply and fixing in repair 10 ltr low level PVC valveless, syphonic action type flushing cistern, white, with ball valve, float and handle including brackets complete all as specified and directed.

Supply and fixing in repair vitreous China wash down water closet pan (pedestal pattern), European type white, Seat and cover for pedestal pan and pedestal pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc (excluding fixing bolts, flushing cistern and flush pipe) etc complete all as specified and directed.

Material & Labour for 75mm thick cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate finished even & smooth without using extra cement as in plinth protection including forming joint to full depth at every 3.0m interval and at every charge of direction and filled mixture of bitumen and sand (1:3) by weight, complete all as specified and directed.

Supply and fixing in repair grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed.

Material & Labour for 2nd class hard wood plain fillets, square, rectangular in section wrought screwed with nails area exceeding 13sqcm but not exceeding 25 sqcm, complete all as specified and directed.

Material & Labour in repair 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in cup board and kitchen cabinet complete all as specified and directed.

Supply and fixing continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flap 30 mm (when open) complete all as specified and directed.

Supply and fixing in repair 100mm size Aluminium handles, cast type, anodised, ISI marked, complete all as specified and directed.

Supply and fixing in repair 100 mm size hasp and staple, mild steel wire type stove enameled black, including bolt to hinge plats and fixed with screws ete complete all as specified and directed.

Supply and fixing in repair 100mm size aluminium anodised, barrel tower bolts of extruded section ISI marked, complete all as specified and directed.

Supply and fixing in repair block boards 25mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work complete all as specified and directed.

Supply and fixing extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails, complete all as specified and directed.

Supply and fixing 25mm dia drapery rod (Poles, finials, ring & bracket complete all as specified and directed.

Taking down existing treatment of any description and any layer from roof including scraping and roughening old by picking, sweeping clean and washing down and removing debris outside MD land complete all as specified and as directed.

Material & labour for screed bed 15 mm thick in cement mortar 1:4 over RCC Roof mixed with water proofing compound @ 3% by weight of cement or manufacturer instruction all as specified. (Note:- water proofing compound shall be measured and paid separately as supply only)

Material & Labour for cement concrete using type B0 1:2:4 (12.5 mm nominal size graded crushed stone aggregate) mixed with water proofing compound in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed. Note:- Water proofing compound shall be measured and paid for separately.

Material & Labour for preparing RCC roof surfaces with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particle and applying APP membrane HMHDPE 3 Kg plain (thickness 3 mm) (total weight of the finished membrane not less than 3.0 kg/ sqm ± 5 % per sqm) confirming to IS 16540: 2017 of following operation complete all as specified and directed:- (a) Applying a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25⁰C, 0.87-0.89 kg/ litre and viscosity 70-160 cps, laying over the primer coat using Butane Torch and sealing all joints, overlapping etc. as per Annex D of IS 16540: 2017 (b) Applying hot blown grade bituminen 85/25 @ 1.20 Kg/Sqm over primer. (c) Laying of polymeric water proofing membrane of weight not than 3 kg/Sqm. (d) Applying a coat of hot blow grade bitumen 85/25 @ 1.20 kg/Sqm over APP membrane. (e) Applying aluminium paint in two coats @ 100gm/sqm in each coat of finished membrane surface complete all as specified and as directed.

Supply and fixing powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed. Note : Minimum thickness of powder coating 50 Micron

Supply and fixing aluminium anodised powder coated window and ventilator shutters side hung type or sliding type or fixed type with or without sash bars of aluminium section weighing minimum 0.55 kg/mtr including necessary jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws including powder coated anodised aluminium fittings such as peg stay 150mm long (1 no), hinge type B-21 100mm long (2 nos) suitable handle (2 no), tower bolt (2 nos), complete all as specified and directed.

Internal Electrification:- Taking down carefully existing aluminium/copper point wiring on batten or in PVC conduit or in MS conduit with GI earth wire etc (for light, fan, socket or power) complete and making good the disturbed surfaces of walls, Floors, ceilings etc to match with existing, complete all as specified and directed.

Disconnecting electric connections and taking down old unserviceable main switches/DB's steel metal enclosure 02 ways/04ways/08ways duly fitted with MCB's cutouts 32 amps capacity including unserviceable wooden boards and making good the disturb surfaces, complete all as specified and directed.

Disconnecting and taking down of unserviceable sub main/ service connection of any size and including steel conduit and accessories and removing from site and making good the disturbed surfacen complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store, complete all as specified and directed.

Material & Labour for point wiring with 1.5 Sqmm (nominal area) single core PVC insulated 1100 Volts, grade multi stranded (FR-LSH) copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type cast iron or pressed steel terminal box for mounting of modular switches, sockets, fan regulator etc with modular white cover plate with frame for suitable module as per site requirements including cutting chasing and making good and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth of following, complete all as specified and directed:- (Note: Cost of cutting chase and making good shall be included in the quoted rate.) Make:- Havells/Finolex/Polycab (a) One light point controlled by one, one way, SP, 5 Amps switch

(b) One fan point controlled by one, one way, SP, 5 Amps switch

(c) One 3/5 pin 5 Amp socket outlet point controlled by one switch on same board.

(d) One 3/5 pin 5 Amp socket outlet point controlled by one switch on independent board.

(e) One bell/ buzzer point controlled by one push button on same board with other switches or independent with cable 1.5 sqmm

(f) One 5 pin, 15 amps socket controlled by Independent 15 Amps switch but with cable 2.5 sqmm.

(g) One 5 pin, 15 amps socket controlled by Independent 15 Amps switch but with cable 4.0 sqmm.

Supply and fixing modular switch 1 way 16 Amp, 1 module, complete all as specified and directed.

Supply and fixing modular socket 6 Amp/16 Amp, 2/3 pin combined, 2 module complete all as specified and directed.

Supply and fixing modular switch 6 Amp/10 Amp, 2/3 pin combined, 1 module complete all as specified and directed.

Supply and fixing modular socket 6 Amp, 2/3 pin combined 2 module complete all as specified and directed

Supply & fix modular bell push, 6 Amp, 1 module, 240 volt single pole complete all as specified and as directed.

Material & Labour for ceiling rose, 3 pin surface, white /any shade, three terminal. Make : Anchor/Leader/SSK

Supply and fixing Bell Multi Music Type, AC 230 volt, Single Pole, complete all as specified and as directed.

Supply and fixing lamp holder, insulated body with back plate suitable for batten fittings. Make : Anchor/Leader/SSK

Supply & fixing New Adore LED lamps 10W B22 COL BALL LAMP, Make:- As per Cat part No- LHLDEUEBML8Z010 of HAVELLS or equivalent as approved bu AGE(I).

Supply and fixing sheet metal enclosure with socket plug top and MCBs double pole and neutral 240 V, 20 Amps enclosure with a two pin and earth plug, and socket complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting 1x9W / 1X10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply and fixing testing and commissioning energy savings security light luminaries 15 watts LED pressure die cast housing with high efficient LED as lighting source and PC cover having TOP Opening including driver compartment with IP66 protection and impact resistance of IK07 including suitable bracket and nut bolts etc all as specified and directed by Engr-in-charge.

Supply and fixing cool white LED bathroom mirror light, 7.5 Watt, AC single phase, complete all as specified and directed. Make:- As per Cat part No.34034/14/86 of Phillips or equivalent in Havells/Bajaj/Crompton.

Material & Labour for refixing/hanging of ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan all as specified and directed.

Supply and fix exhaust fan (M.D.supply) 230V, 300mm sweep and connecting up including provision of cable from ceiling rose/connector to fan complete all as specified and directed.

Supply and fixing in replacement of ceiling fan regulators, stepped type AC, 230 Volts complete all as specified and directed. Make:- Anchor/leader/SSK

Supply and fixing MCB distribution board steel sheet, enclosure power coated fitted with bus bar, neutral link, earth bar din rail confirms IS-8822:96 and EIC 898-96, 240V double door when MCB SPN 04 way to be used, complete all as specified and directed.

Supply and fixing of MCB in DB's /Isolator of the following rating complete all as specified and directed:- (a) MCB SPN 40 amps curve 'C' breaking capacity 10KA

(b) MCB SP 6-32 Amps, curve 'C' breaking capacity 10KA

Material & Labour for concealed submain wiring with two run of 6.00 sqmm single core multi stranded ISI marked PVC (FRLSH) insulated copper conductor cable drawn through concealed in surface in PVC rigid conduits and the conduit accessories not less than 25mm including one run of earth continuity conductor with 6.00sqmm multi stranded copper conductor including cutting chase and making good to disturbed surfaces of wall with cement mortar 1:3 including necessary plaster and pointing in cement mortar 1:3 with white wash/distemper/other paintings complete all as specified and directed by Engineer-in-charge. complete all as specified and directed. Note:- 1. Two run of single core cable, one run of earth continuity conductor and one run of conduit shall be measured as one unit. 2. Cost of cutting chase and making good shall be included in the quoted rate.

Fixing only old energy meters of rating 10-40 Amps including making incoming and outgoing connections etc complete all as specified and directed.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated cable for working voltages of 1100 V, PVC sheathed, armoured, 4 core with nominal cross sectional area of main conductor 16 sqmm, stranded aluminium conductor, ISI marked as per IS 7098(Part-I): 1988 including cable glands, lugs etc. to suit the cable size and to be laid in trenches, fixed along pole, under floors, through GI pipe laid under floors/roads, through concealed GI pipe along wall etc. complete all as specified and as directed.

Excavation in trenches in hard/ dense soil not exceeding 1.5mtr deep and not exceeding 1.5mtr wide for laying of cables, RCC /steel tubular pole/stay and struts etc getting out including trimming sides and forming bottom surface complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming excavated soil in layer not exceeding 25cm thick each back in trenches after cables have been laid and tested, poles, stays, struts have been erected and tested all as specified and directed at site.

Removal of excavated surplus material to distance not exc. 50meter away in layer not exceeding 25cm from the starting point all as directed by Engr-in-Charge.

Material & Labour for old size sub class 'B' bricks straight or curved on plan exc. 6 meter mean radius for cable cover. complete all as specified and directed.

Material & Labour for dry sand cushioning to UG cable with a layer of sand of 8 cm thick before laying of cable and 15 cm thick after laying of cable to full width of trenches complete all as specified and directed. Note:- For the purpose of payment only punned thickness will be measured

Supply and fixing light grade 40mm GI pipe fix complete to wall, poles etc with suitable clamp for protection of cable complete all as specified and directed.

Material & Labour for earthing complete with GI earth plate electrode 60cm x 60cm x 6.3mm thick, burried directly in ground (earth pit not less than 2.5mtr deep below normal ground level) with top edge of the plate not less than 1.5mtrs below normal ground level connected to GI lead wire 4.00mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electric plate No.3 of SSR part-I connected to continuous earth wire on main switch board all as specified or indicated and testing on completion including provision of earth wire protection by 15mm dia medium grade GI pipe and watering pipe shall be 20 mm bore, medium grade including excavation and earth work, PCC pit with RCC cover, charcoal salt funnel, GI wire up to 7.5mtrs length complete all as specified and directed.

NOTE :- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs 19,362.00 /- ]

M/s VIKAS TRADERS

d k suppliar

SUNIL KUMAR KORPAL

OM BUILDER