SAIL Gua SnT Work

Total Amount of BoQ

Amount after unconditional Rebate

Item Rate BoQ

BoQ_Ver3.0

eTender No: RITES/PU-BBSR/S&T/SAIL-GUA/OT-12/2025-26, dated: 30.01.2026

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

S & T WORK

BoQ3 SCHEDULE - A1 (EI Execution Schedule)

BoQ4 SCHEDULE - A2 (Indoor & Outdoor Execution Schedule)

BoQ5 SCHEDULE - B1 (EI Supply Schedule)

BoQ6 SCHEDULE - B2 (Supply Schedule)

BoQ7 SCHEDULE - C (Drawing & Design)

Percentage BoQ

BoQ_Ver3.0

eTender No: RITES/PU-BBSR/S&T/SAIL-GUA/OT-12/2025-26, dated: 30.01.2026

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE - A1 (EI Execution Schedule) (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bid is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Percentage BoQ

BoQ_Ver3.0

eTender No: RITES/PU-BBSR/S&T/SAIL-GUA/OT-12/2025-26, dated: 30.01.2026

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE - A2 (Indoor & Outdoor Execution Schedule) (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bid is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Transportation of Position Light Shunt Signal complete with post, units, bases and other fittings; excavation of pit, casting of concrete foundation (1 : 3 : 6) as per Drg. No. CON/SK/T/13, complete fittings of signal including termination of cables, wiring, focusing and testing. SAIL. will supply position light shunt signal with base from store. Tenderer shall supply all other materials required for the work.

Transportation & fixing of Calling On Signals/ dependent shunt signals with marker for multiple aspect colour light signals on the erected signal posts complete with marker including termination of cables, wiring, signal testing, and focussing. SAIL. will supply only calling-on-signal/dependent shunt signal with off-set bracket from stores. Tenderer shall supply all other materials required for the work.

Transportation of signal posts for multiple aspect color light signals, complete with signal units, bases, ladders and other fittings, excavation of pit, casting of cement concrete foundation, plastering as per Drg.No Con/SK/T/12, erection and fixing of complete fittings of the 2/3/4 aspect signal/signal posts including termination of cables, wiring, LED fixing, signal testing and focusing. Name plate & marker and all other materials shall be provided by the contractor at his own cost. Required cement shall be supplied by the contractor. Arrangement of Screening to be provided by the contractor if required as instructed by site Engineer. Contractor shall prepare jointly with SAIL. Engineer at site and submit Signal Sighting report and Signal test report as per approved format of SAIL.

Transportation and fixing of Junction Type Route Indicator (1 to 6) way complete/stencil Type/Multilamp type route indicator on the erected signal post including cable termination, wiring, painting, lettering, signal testing, and focusing, Tenderer shall supply name plate & marker and iron mesh (if required) at his own cost.

Fixing of route Indicator/Shunt LED in units, LED type lamp unit with current regulator in illuminated marker/route indicator unit. This includes taking the cable inside the unit, fixing of current regulator etc., complete wiring, fitting of terminals, LED signal lamps, and dismantling of existing lamps and fittings as required. The painting and lettering of existing markers and numbering plate to be done by enamel paint. All materials including PVC wires, blanking stretcher, PVC flexible pipe, hylum strip (6 mm thick), terminals and all sundry materials are to be supplied by the contractor. SAIL. will supply LED Units.

Fixing of RED/YELLOW/GREEN LED type lamp unit with current regulator. This includes taking the cable inside the unit, fixing of current regulator etc., complete wiring, fitting of terminals, LED signal lamps, and dismantling of existing lamps and fittings as required. The painting and lettering of existing markers and numbering plate to be done by enamel paint. All materials including PVC wires, blanking stretcher, PVC flexible pipe, hylum strip (6 mm thick), terminals and all sundry materials are to be supplied by the contractor. SAIL. will supply LED Units.

Fixing of Calling On LED type lamp unit with current regulator in Calling on signal unit. This includes taking the cable inside the unit, fixing of current regulator etc., complete wiring, fitting of terminals, LED signal lamps, and fittings as required. The painting and lettering of existing markers and numbering plate to be done by enamel paint. All materials including PVC wires, blanking stretcher, PVC flexible pipe, hylum strip (6 mm thick), terminals and all sundry materials are to be supplied by the contractor. Railway will supply LED Units.

Transportation, excavation of pit, casting of foundation, plastering and erection of Steel Apparatus case (full size) with fixing of E-Type lock, wiring, cable entry, termination clamping, filling cable pit with sand, painting and lettering etc., as per Drg.No. S&T/CON/SK/16. This includes earth work and/or masonry work required for securing the apparatus case as per site condition. SAIL. will supply apparatus case with 'E' type lock only. Tenderer will supply all wiring materials, PBT Terminals, fuses, fuse blocks, bus bars, hylum sheet ISI mark [6mm thickness], wood plank board of good quality [minimum 3/4" thick], Cement and transport all the materials to site of work at his own cost. The wiring materials such as wire coils, PBT terminals, fuses, fuse block, etc. should be used from RDSO approved sources. 1) Modifiaction of inside arrangement of Apparatus cases if required for fixing of relays/transformers etc. shall be done by the contractor. Extra shelf, if any, shall be deposited to the SAIL. stores by the contractor. 2) All cables shall be terminated by providing copper eyelet of suitable size.

Transportation, excavation of pit, casting of foundation, plastering and erection of Steel Apparatus case (Half size) with fixing of E-Type lock, wiring, cable entry, termination clamping, filling cable pit with sand, painting and lettering etc., as per Drg.No. S&T/Con/BBS/92/90. This includes earth work and/or masonry work required for securing the apparatus case as per site condition. SAIL. will supply apparatus case with 'E' type lock only. Tenderer shall supply all wiring materials, PBT Terminals, fuses, fuse blocks, bus bars, hylum sheet ISI mark [6mm thickness], wood plank board of good quality [minimum 3/4" thick], cement and any other materials that are required for the work at his own cost. Contractor has to transport all the materials from store at his own cost to the work site. The wiring materials such as wire coils, PBT terminals, fuses, fuse block, etc. should be used from RDSO approved sources. 1) Modifiaction of inside arrangement of Apparatus cases if required for fixing of relays/transformers etc. shall be done by the contractor. Extra shelf, if any, shall be deposited to the SAIL. stores by the contractor. 2) All cables shall be terminated by providing copper eyelet of suitable size.

Transportation, fixing and wiring of 24/30-way junction box Tenderer shall supply all wiring materials, hylum strip ISI mark (6mm thickness), MS angle for fixing and any other materials that are required for the work at his own cost. SAIL. will supply 24/30 way JB & PBT terminal from the store.

Transportation, installation, wiring, testing and commissioning of RKT on 20 mm pre-laminated, BWP, termite proof, borer proof plywood (on a 12 mm Hylum sheet ISI Mark) of size 300 mm X 400 mm X 12 mm per RKT, including termination of cable/indoor wire, LED, push buttons etc. SAIL will supply only RKT. Tenderer will supply all other required materials for the work. Inspection of plywood/Hylum sheets by Representative of SAIL before use.

Transportation, installation of point machine on MS plate fixed on wooden/psc/steel sleeper complete with fixing of anti theft arrangement, 'D' Bracket, junction boxes, connection including smithy works involved for ground connection, including rivetting/welding of angle cleats, termination of cables. Preliminary adjustment for operation of points by crank handle. oiling, greasing, painting and lettering as required. This also includes supply and fixing telescopic arrangement using GI pipes of required dia for provision of wires from junction box to point machine. SAIL. will supply point machine, ground connection from stores. Tender shall supply all other materials required for the works.The contractor shall overhaul the point machine before installation.

Wiring and testing of electric point machine as per the wiring diagram supplied by theSAIL. This also includes the connection of complete ground connections of electric point machine and fixing of insulation materials and providing one number of seven lever [7 levers] Godrej lock with three keys each, per machine for outside cover, fixing arrangement of crank handle interlocking in point machine, and fixing of 'E' type lock [if required]. SAIL will supply electric point machine, ground connections with insulations and junction boxes. Tenderer shall transport the materials issued bySAIL. to the site of work at his own cost and shall also supply materials such as PVC wire for wiring, one number of Godrej (7 Levers) lock with three keys each per lock, per point machine, and any other materials that are required for installation, wiring, testing and commissioning of the said work at his own cost. Also Preparation of point parameter history records and maintenance register duly recording the measurements in prescribed format jointly with SAIL. representative and handover all records to the SAIL.

Supply, transportation, erection, and grouting of Composite Relay Racks / Relay Racks / CT racks as per Drg.No. SK/DRG/OL/SER/192, SH-1/2 (for Composite Relay Racks), Drg.No. SK/DRG/OL/SER/192, SH-2/2 (for Relay Racks) and Drg.No. S&T/CON/HQ/VSKP/95/92 (for CT Racks) respectively, including fixing of racks, PBT terminals 1-Way/6-Way, ND Fuses, Bus Bars, Eyelets, Hylum strips of required thickness [12 mm] as per length required at site, condensers and resistances etc., wherever required as per directions of Site Engineer. Inspection of Composite Racks / Relay racks/CT racks by Representative ofSAIL. before use. Tenderer shall supply all the materials from RDSO approved sources such as PBT terminals 1-Way/6-Way, ND Fuses, Fuse blocks, Bus Bars, Eyelets, Hylum strips (12 mm thicknessn ISI Mark) condensers and resistances etc., and any other materials required for the work at his own cost.

Supply, transportation and fixing of MS ladder with suitable clamping arrangement & associated masonary and smithy work in Relay room, equipment room, Battery room, Goomties and cabins etc. The MS ladder should be made of 1" X 1" (1/8"/3 mm thickness) and MS flat size of 1" wide X 1/8" / 3 mm thickness. MS flat shall be provided at every 8"apart. Width of ladder shall be 8". Tenderer shall supply all materials for this work. Inspection By representative of SAIL. before use. [RM=Running Meter]

Wiring and testing of complete Relay Rack / CT Rack / Composite Relay Rack as per wiring diagram for maximum number of plug in type relay & shelf type relays of different sizes or as directed by SAIL Engineers at site. This includes rack to rack wiring through MS ladder fixed on the top of the relay rack, crimping eyelets in the terminals fitted in the cables termination rack, numbering by ferrules 2.5 sq. mm, bunching of wires by bunching Tape/Thread and buttons, painting and lettering as required. Wiring of the racks shall be done with PVC wire of size 16/0.2 mm and 3/0.75 mm. Tenderer shall supply all wires & wiring materials purchased from RDSO approved sources. Note: 1) Only relay and relay bases will be supplied by the SAIL.. Contractor has to supply all other materials for the above work and make arrangement for transportation of materials supplied bySAIL. at his own cost. 2) Only brass screws shall be used for fixing of relay bases. 3) All types of wires and wiring materials, eyelets of sizes (make: Dowell's or similar), ferrules (2.5 sq.mm), resin core solder, insulating tape, bunching belt & buttons etc. are to be supplied by the contractor. Wires will be procured from RDSO approved sources only and all other components will be supplied by the contractor as per requirement at site.

Excavation of trenches of following depth and width 0.3 Meter detailed below including clearing of roots and trees etc. for all types of soil. This work also includes covering of cables laid in trench and backfilling, ramming, consolidation of soil as well as disposal of extra soil after cable is laid as specified in Guidelines on Signalling Cable laying given by RDSO and any latest circular issued by Railway Note: Before refilling of the trenches, the cable laid are to be tested and recorded for its insulation value and after satisfaction of site Engineer the refilling process should start and after monsoon the route is to be attended for backfilling the rain cuts, wash out of soils where ever found.

1.0 Meter

0.8 Meter

Excavation of trenches in all kinds of soils including soft rocky area and clearing of track etc. to a depth of 1.0 M and width of 0.3 M for track crossing /pucca road/level crossing gate/platform/station circulating area or any other place as advised by site Engineer including transportation and laying of DWC/RCC/Split RCC/G.I. pipes with or without coupler. This includes repairing of track/pucca road/level crossing gate/ platform/station circulating area surface to original position by ramming and concreting wherever required soon after the work is over. DWC/RCC/GI pipes shall be supplied by the SAIL.. DWC pipes wherever required shall be supplied in 6 Mtr. length and shall be cut to size as per requirement. All other materials including cement are to be supplied by the contractor.

Excavation of trenches including clearing of roots of trees etc., in rocky area up to a depth to be indicated by SAIL Engineer at site as per the site condition [Minimum 0.6 meter] and width 0.3 Mts. at the bottom. This includes concreting & plastering as per the instructions of site Engineer and complete back filling by digging earth from a lead of 30 Mtr. In case 0.8 meter depth or higher is achieved no concreting is required, otherwise concreting up to 100 mm thickness should be done. All materials required for the above works shall be supplied by the Contractor.

Cutting of masonary floor/walls at station building/ signal goomty/ Gate lodge at a depth of 0.5 mtr. to 1.0 mtr at places to be indicated by site Engineer for entering of cables inside the building. Only G.I pipes supplied by SAIL. and all materials as clamps, bolts & nuts as instructed by site Engineer supplied by tenderer. This includes repairing of masonary floors/walls after the cables are taken inside. Cement, Sand required for the work shall be supplied by the tenderer and also transportation of G.I Pipe from Store by the tenderer.

Laying of Signalling/4 Quad/ 6 Quad/ Power Cable/Telecom cables/ Jelly filled cables of all sizes in excavated trench, through GI/RCC/DWC pipes etc. wherever required. This includes transportation of cables from the stores to work site and transportation of empty cable drums with left over cables from site to the stores. The length of cable laid includes the length of cable coil for termination purpose. NOTE: The cables are to be carefully handled during loading, un-loading and transportation to work site. Any damage found in the cable after final testing, in view of mishandling of cables, shall be made good by the Tenderer. Cable should be maggered before and after laying and recorded in a register and submitted to the site Engineer.

Transportation, laying of all sizes of split double walled corrugated (DWC) pipes in the cable trench parallel to track or as advised by site engineer.

Trenching and fixing of G.I. pipes of different sizes/DWC pipes in hard rocky area up to a depth of 0.3 M to 0.6 M or at places as per instruction of site Engineer and concreting [1 : 3 : 6] up to height of 100 mm above the pipes. G.I. pipes with the socket/ DWC pipes shall be supplied by the SAIL. All other materials required for the works shall be supplied by the contractor. Note: [1] In case of girder bridges, G.I. pipes shall be suitably clamped by the contractor as advised by the site Engineer. Clamps shall be supplied by the contractor. [2] The work including excavation of trenches in hard rock area up to a depth of 0.3 M to 0.6 M and back filling, ramming after completion of work where ever required. [3] In case of concrete bridges clearing of ballast for laying of pipes and re arranging the SAIL ballast after completion of work shall be done by the contractor.

Transportation of HDPE pipe from the store to work site, laying of the same (With 4 mm nylon rope, pre inserted inside the HDPE pipe) in excavated trench/ already laid GI/ RCC pipe / tubes, jointing, leveling and end sealing the pipes, HDPE pipe, couplers and end caps shall be supplied by SAIL. Nylon rope shall be supplied by the contractor.

Transportation of OFC from the store of to work site with care, and pushing/ pulling OFC through the HDPE pipes sealing of the duct by simple plugs. The cable is to be laid by mechanised means. At inaccessible places where mechanised laying is not possible, the cable is to be laid manually by pulling through pre inserted rope. Empty cable drums with or without leftover cable should be returned to the store. This also includes testing of cable drums by OTDR in the store premises before transportation and submission of results thereof.

Transportation and jointing (straight through and derivation) of PIJF/quad cables size TSF-IV as per Specn No. IRS: TC-31/96 & IRS 30/97. Jointing kits shall be supplied by the SAIL. All other materials shall be supplied by the tenderer.

End to end testing of all fibers of the optical fiber cable between station/ cable huts. This includes submission of test results in 4 copies as detailed in the technical specifications to be collected from the SAIL.

Cable Duct behind the Relay room and Goomties of size 1.8 M x1.8 M x 1.2 M to keep cables entering into it consisting of brick work of 254 mm thickness of proportion 1:6 with sand filling after coiling of cables. The top of sand filling covered with concreting of size 1.30 M x1.30 M and a depth of 200 mm of proportion 1 : 1.5 : 3 outside of the duct should be plastered with cement mortar 1 : 6 to achieve smooth finishing. All materials including cement and chips of size 40mm. and second class bricks etc. to be supplied by the contractor.

Excavation of cable joint pit of size 1m x 1mx 1.2m in all types of soil for jointing of copper cables, back filling and ramming after jointing.

Supply, transportation and Installation of 10/20/50 pair Aluminium CT Box and termination of cables inside C.T. Box in station building cabin/office/quarters as per instructions of site Engineer. All materials like C.T. Box shall be supplied by the contractor at his own cost. Inspection by representative of SAIL. This also includes painting and lettering of description.

Installation of lightening arrestor Class A device on the top of the building. the devices shall be installed at the height of about 3 mts from the roof of building using a G.I. pipe. The device shall be connected to the earth pit using the copper tape 25mmx1.5mm or better the copper tape shall be run firmly along the side of the mast with the help of the spacers. It shall also be ensured that this down conductor shall not touch the building through out. The down conductor should be connected to the separate earth electrode as per Railway Board guidelines using exothermic welding. A counter shall be installed at an appropriate place to count the no of occurrences. All the accessories like spacers, welding material etc required for the installation shall be arranged by the contractor only. The installation of Lightning Arrestor should done by authorised representative of OEM.

Alteration of wiring in existing apparatus cases full/half. This includes supply of all materials in connection with alteration in wiring. All the materials shall be supplied by the contractor at his own cost. This includes entry of cables, sand filling and masonry work involved. Lettering and painting to be done by the contractor at his own cost. Railway shall supply only relays and relay bases.

Wiring and fixing, of Surge Protection Devices complete with all accessories, fixture as per the following description. SAIL. will supply only SPD and all other materials required for the works shall be supplied by the contractor.

Surge Protection Device for 230 V AC input to PC, complete with enclosure and connected wire as per technical specification No:RS-SPD-5.

Surge protection Device for 110V AC input to signals complete with connected wire .

Surge protection Device for 110V DC input to IPS Goomty, complete with connected wire as per technical specificition No:RS-SPD-7.

Surge Protection Device for 24V DC supply complete with connected wire as per technical specification No: TS-SPD-3.

Surge Protection Device for 12V DC supply complete with connected wire as per technical specification No: TS-SPD-3.

Transportation, Installation, wiring, testing and commissioning of Data Logger system 1024 digital input and 64 analog input as per specification No.IRS:S-99/2006 or latest at station and goomtys. This includes (i) Changes in design of Data Logger for installation in Electronic interlocking station (ii) Wiring and testing of protocol converter unit for EI station (iii) Modification in software and hardware if required and networking with other data loggers along with fault logic design. (iv) Wiring of all external relays to Data Logger as per RDSO guide lines.

Installation, Transportation, testing, Commissioning & Networking of RTU-Data logger 64/128 digital inputs & 16 Analog inputs as per RDSO Spec No-IRS-S-99/2006 or latest amendment if any. This includes wiring of potential free contacts from existing relays, contact of analog devices (Chargers, Battery, Power supply etc) and its usage inatalogger and its necessary wiring required for the work. The wiring materials will be used as supplied in Schedule-B including 40/60 core cable. Any other wiring material if required shall be supplied by contractor. Wiring of all external relays to Data Logger as per RDSO guide lines. The work is to be executed as per directives of SAIL. Representative.

Transportation, installation, testing and commissioning of Multi section digital axle counter (MSDAC) in complete system with all DPs of different track section configuration as per enclosed drawing. Axle counter device complete with standard accessories shall be supplied by the SAIL. All sorts of terminals, sealed wires, condensers, resistances etc., HDPE pipes and all other materials required for the above work shall be supplied by the contractor. This includes design, installation, testing, commissioning of MSDAC evaluation arrangement with all necessary modules cards, interface cables, software and other materials etc., execution of associated work for working of axle counter through OFC/Quad cable. The tenderer shall ensure that axle countr installed by the OEM.

Transportation, installation, wiring of Integrated Power Supply system. SAIL will supply only IPS system, red and black copper cable of 25 Sq mm size or as required as IS: 694 and grade 1100 V for connecting IPS to battery bank for 300/200 AH battery. Tenderer shall supply all wires and wiring materials required for the installation including DPDT switches of required numbers of ANCHOR/CROMPTON/HAVELLS/L&T to make 250V AC 32 Amps/415 V AC 63/100 Amps capacity or as per requirement. Electric wiring and bringing AC input supply from auto change over CLS panel at the station to IPS, all wiring /ducting from SM room to IPS room, from IPS room to relay room or any other load to be done by the contractor. All other copper cable of required dia as per installation manual and other wiring materials to be used for power wiring will be supplied by the contractor at his own cost.

Supply, installation, testing and commissioning of Maintenance free and permanent earth as per RDSO Specification No. RDSO/SPN/197 Version 1.0 and as per Technical Specification in tender document.

Painting, varnishing, numbering, lettering and graphiting of all outdoor and indoor signalling equipments over and above the initial painting as per instruction of SAIL. representative at site. This includes supply of paints, varnish, graphites and any other consumables by the contractor.

Wiring, testing and commissioning of overall circuits and ground gears of approved interlocking arrangement as per approved circuit diagram and Interlocking plan. This also includes making corrections/alterations in As Planned drawings and documents as per the execution at site. This includes Free home signal connection at site and SM's office, telephone connection in the tents/goomties and any other communication arrangement for the Non interlocking at the station or as decided by the representative of SAIL. during non interlocking. The materials required for preparation of Free Home indication board will be supplied by the tenderer.This also includes painting and lettering of gears. Telephone , VHF Sets/Walkie Talkie sets will be supplied by SAIL. Note: In case of IBS : It includes overall testing and commissioning of IBS and both the end stations associated with IBS modification.

Supply, Fixing and wiring of distilled water plant including connection with water supply line, supply, fixing and wiring of 16 Amps power supply board with change over switch for local/AT (and D.G supply if required) by 7/0.29 wire from local Main/AT/D.G supply through PVC pipe and execution of strengthening, rearrangement, masonry, plumbing and all other work as specified by the SAIL site engineer. Materials such as wire(7/0.29), PVC pipe, power supply board, GI pipe as required, tap for water supply, cement and all other materials required for the above work including distilled water plant shall be supplied by the contractor. Distilled water plant to be inspectede by the representative of SAIL.

Supply, installation, testing and commissioning of Automatic Fire Alarm & Detection system as per RDSO Specification No. RDSO/SPN/217/2018, Ver. 2.0 or latest and as mentioned in technical specification of this tender document. Fire alaram to be inspected by SAIL. representative.

Supply and installation of Rodent Repeller for covering the Relay Room and Power Room.

Fixing, testing and commissioning of way side control equipment with telephone, hot line phone and auto telephones, Control equipments, switch board cable and telephones shall be supplied by SAIL., other fixing materials shall be provided by the contractor.

SDH add drop or terminal multiplxer (Short haul with 21 E1). The E1 streams shall be suitably terminated on Digital distribution frame (DDF) as per SAIL. directives.

Primary drop Insert Multiplexer with all interface cards including connection to the bus bar as per approved channeling plan.

Supply, transportation, foundation, erection, painting and lettering of legend board, stop board etc with 4" [minimum] GI channel iron support length as per G &SR , SEM and IP. This includes excavation pit as per approved drawing of the SAIL for casting of base foundation [ratio 1 : 3 : 6] . all the materials required for the above works shall be supplied by the contractor. Note: approximate size of the legend board shall be 24" X 18" X 1/5". Inspection of legend board, stop board etc shall be done by representative of the SAIL.

Track crossing by horizontal boring method as per technical specification given in Tender document.

Supply, transportation, installation, testing and commissioning of earth electrode (make TATA or Jindal as per Rly. practice) as per SER Drg. No. Con/SK/8/3/84 in TS, construction of cement enclosure to Drg. No. CON/SK/T/9A and drawl of 6 SWG wire or 2 Nos. of 8 SWG wires or Signalling cable if given by SAIL. in place of 6/8 SWG wire/s, from earth electrode to place advised by the site Engineer including fixing and soldering of lugs and measuring, painting of the earth resistance etc. Inspection of earth electrode By representative of SAIL. before use. Tenderer shall supply all materials such as cement, charcoal, salt, GI wire, lugs, 8X40 mm galvanized hex head bolts etc that are required for the work. NOTE: This includes testing of earth value and indicating the same on the Earth enclosure by paint.

Transportation, installation, wiring, adjustment, testing and commissioning of High availability single section digital axle counter device with dual track sensor complete including termination of cable. Axle counter device complete with standard accessories shall be supplied by the Railway. All sorts of terminals, sealed wires, condensors, resistances etc, HDPE pipes and all other materials required for the above work shall be supplied by the contractor. This includes execution of associated work for working of axle counter through OFC/TDM Multiplexer (MROTEK or Similar). The installation certificate shall be submitted from the OEM.

Transportation, installation/ replacement/shifting, termination of cables, complete wiring, testing and commissioning of Block Instrument [Single/Double line/TLBIl including all accessories and sub systems, filter units, and telephones as per approved diagram and Railway directives. This also includes dismantling of existing block instrument and alterations of wiring of existing block circuit as required at adjacent stations. Only Block Instruments and standard accessories shall be supplied by the Railways. All other materials required for the work shall be supplied by the contractor. Note : 1) Each block shall be provided with separate earth. Value of each block earth resistance shall be measured separately and to be written on the earth pit before commissioning.

Excavation of pit to required size as directed by Engineer in charge at site and casting foundations in the ratio of 1:3:6 cement, sand and metal (40mm stone) all to be supplied by contractor approx 10 Nos. per each sliding gate or as directed by Engineer in charge at site.

Dismantling of the signal post/warning board/Location box with complete fittings.This includes dismantling, stacking and accountal of all the materials including transportation of all released materials to the Railway store or as instructed by the Railway.

Dismantling of all existing indoor electrical and mechanical signalling gears at end cabins,stations etc. This includes old signalling equipments such as lever frame, relay racks, SM slide box, block instruments and all such indoor gears. This includes dismantling, stacking and accountal of all the materials including transportation of all released materials to the Railway store or as instructed by the Railway.

Maintenance of all the installation of PI/EI stations including ouldoor and indoor under an able and competent supervisor for a period of 30 days from the date the works handed over to traffic. Payment shall be released only on completion of residual works as pointed out by Railways. [i]During the above maintenance period contractor has to replace/repair any defect Ito the installation pointed out by the Railway administration at contractor's cost without endangering Railway safety and Safety rules. [ii]During the above maintenance period contractor shall comply all the residual works and carry out petty repairs and arrange attending of failures promptly by [keeping artisan staff and helpers, conversant with signalling system must be lavailable round the clock. [iii]The contracior shall supply of minimum 5KG of Grease, Lubricating oil of 5 Ltrs for point machines, lubricants (black oil), distilled water, cotton waste of 5Kgs and all other petty consumables for regular maintenance. [iv]The contractor shall supply & prepare all the required registers te. cable insulation register, Track History card, Battery History Register, Equipment History Register, Signal Lamp History Register, Joint S&T & Paway Inspection Register Earth register, Axle counter reset register, axle counter channel voltage register, digital axle counter register, point testing register, emergency operation register (points, gate elc.) etc. and maintain the records neatly cabin-wise for signalling gears Ion standard Perfora as per the directive of Railway administration for handing over the maintenance to the Open Line. Format of register should be as per the advice of the site Engineer. Each register of A-4 size of 50 pages one side/both side hard bound. 2 Nos of register of each type mentioned above should be supplied. [v]The contractor has to supply all the registers mentioned above before taking Non [Interlocking. Maintenance of upto 5 line station.

a] Installation and testing of Straight Portion track circuits including supply of materials as per directive of site Engineer. NOTE: (i) This includes drilling 9/32" holes on rails, provision of bonding, fixing of track lead junction box, provision of track lead jumper wires, fixing of track circuit equipment i.e. track charger, resistance, fuses, batteries, chokes, relays, anti-titling arrangement (if required), painting, lettering and numbering etc. This includes insulation of gauge tie plates, Crossing plates, rod in siding points if required or any other place as instructed by Railway Site Engineer, by tenderer's insulation materials. (ii) Preparation of Track circuit history records and maintenance register duly recording the measurements in prescribed format jointly with Railway representative and handover all records to the Railway. NOTE: 1.Railway will supply Track Charger, B -type choke, Resistance, battery, TLJB and relays from the stores and are to be transported to site of work at contractor's cost. Tenderer shall supply any other materials that are required for the work.

b] Installation of Curved Portion (Point Zone) track circuits including supply of materials as per directive of site Engineer. NOTE: (i) This includes drilling 9/32" holes on rails, provision of bonding, fixing of track lead junction box, provision of track lead jumper wires, fixing of track circuit equipment i.e. track charger, resistance, fuses, batteries, chokes, relays, anti-titling arrangement (if required), painting, lettering and numbering etc. This includes insulation of gauge tie plates, Crossing plates, rod in siding points if required or any other place as instructed by Railway Site Engineer, by tenderer's insulation materials. (ii) Preparation of Track circuit history records and maintenance register duly recording the measurements in prescribed format jointly with Railway representative and handover all records to the Railway. NOTE: 1.Railway will supply Track Charger, B -type choke, Resistance, battery, TLJB and relays from the stores at and are to be transported to site of work at contractor's cost. Tenderer shall supply any other materials that are required for the work.

Miscellaneous arrangement for NI/Commissionning period comprising of Provision of water-proof Ls [temporary goomty/tent at both side of the station yard and at central panel building. Each goomties to be furnished with one iron table, six chairs, emergency light and mosquito repellent caps for NI staff, PA system, crowbar men for operating point and Imen for supolving water to tents.

Alteration of wiring in existing Relay rack/ CT rack/composite relay rack. This includes supply of all types of wires, eyelets, nuts & bolts, bunching material, ferrules, ARA terminals, fuses & fuse blockes by the contractor at his own cost. Lettering & painting to be done by the contractor at his own cost. Wire (RDSO Approved Sources) to be inspected by the representative of SAIL before use.

Installation and commissioning of 25W radio at station buildings. This also includes erection of power supply unit and antenna with support pipe.

Installation, Wiring, testing & Commissioning of LT Power Panel with Auto Change Over. This includes fixing of Power Panel, termination of LT Cables and Supply of Nuts, Bolts, MS Angle etc.

Installation of DG set, testing and commissioning, . This includes casting of vibration free foundation, installation of ASM panel, outlet for exhaust panel, laying of power cable from DG room to ASM room for remote operation of DG set and wiring of DG set of ASM panel, laying of cables/wires should be carried out in HD PVC channel/ conduit pipe. This includes cost of all mateials required for installation except DG set and ASM panel. Wires/cables as extant practice on Railways and instruction of Engineer at site.

Splicing of laid under above items OFC cable and making the splice joint in dust free environment with contractor's own equipments and labour. Straight joint enclosure (SJC) is covered under supply schedule-1 remaining all required materials, tools, plants shall be arranged by the contractor, splicing shall be started from one end and each splicing shall be monitored after splicing and after closing the enclosure for all the fibres from one central location by contractors engineer with his own OTDR and optic Talk set with owenrs engineer, trace for the fibres shall be taken and signed jointly, if any fibre splice shows high loss/lossy event, the same shall be redone before completion of splicing work. The splice loss shall be as per the policy/technical circulars issued by the railways from time to time.

Installation, testing and commissioning of battery charger & maintenance free VRLA cells at station. Note: The rate quoted shall be including the cost of DC bus bar of 48 VDC/ Power wire suitable stand etc., connection of power supply to the equipments. All the wiring shall be done with the suitable gauge of power wires through suitable casing/caping as per the instructions of representative of SAIL. engineers. All the materials required for this item shall be supplied by the contractor.

Wiring, installing of Magneto / DTMF telephone in ASM office, at locations, Relay Room, connected on both directions.

Preparation/Revision and supply of station working rule (SWR) and SWR diagram as per S. E. C. Rly practice. The item includes supply of two sets of drawing and write up for approval. Contractor will supply completion SWR and SWR diagram and two CDs after final commissioning of the station.

Installation of fiber distribution management system (supply covered above) with all installation materials, restoration wall etc. to original condition, splicing and termination of 2x24 fiber cable (with all contractors materials), routing/dressing fiber as per directions of Engineer incharge.

(a) Route Control Charts (RCC)

(b) Logic Circuits

(c) Interface Circuits

Independent Checking and Verification of following S&T drawing by accredited license holder (IRSE/IRSTELO): (a) Cable Core Plan (CCP)

Upto Four-Line Station

Upto Ten-Line Station

Percentage BoQ

BoQ_Ver3.0

eTender No: RITES/PU-BBSR/S&T/SAIL-GUA/OT-12/2025-26, dated: 30.01.2026

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE - B1 (EI Supply Schedule) (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bid is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Design, manufacture, supply and transportation of Electronic Interlocking System (Centerlized Configuration System with hot stand by features) for Station complete as per the special conditions of contract & Technical Specifications. This includes supply of Computer Maintenance Console-1 No, Computer Operator Console-2 Nos, Surge Protection Devices, DC-DC Converters and FAT & SAT for the EI System. The Equipment shall confirm to RDSO/SPN/192/2019 Ver.2 or RDSO/SPN/203/2011 Ver.1 with latest amendments and as per enclosed technical specifications. Inspection by RDSO. NOTE 1:- This includes supply of all interface Relays and Relay Racks for EI system. NOTE 2:-If required depending upon yard alteration, Additional cards/modules/sub-items and Essential spares shall be procured as per the variation clause incorporated in this tender document. The tenderer shall supply the spares as per the accepted rate of Items/Sub-items/Modules of item No-1 of Sch-B-I and as per same terms & conditions.

Supply of EI equipment for the routes up to 70 routes

Percentage BoQ

BoQ_Ver3.0

eTender No: RITES/PU-BBSR/S&T/SAIL-GUA/OT-12/2025-26, dated: 30.01.2026

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE - B2 (Supply Schedule) (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bid is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Supply of Shunt Signal Position Light, ground type independent complete as per RDSO Spec No. RDSO/SPN/153/2011 with base, hoods, number plate, Post wire mesh, post to Drg. No. SA-23840 (Adv) latest for shunt signal, SA-23202 for base, IRS:S-6/81 for post. Inspection by the Representative of SAIL.

Supply of Shunt Signal Position Light, dependent post type complete as per RDSO Spec No. RDSO/SPN/153/2011 with offset bracket 90 mm dia to suit 140 mm dia post to Drg. No. SA-23840(Adv.) with latest amendments for shunt signal & SA-23040/M for offset bracket 90 mm. Inspection by the Representative of SAIL.

Supply of Signal colour light multi unit as per specification No: IRS: S-26/64 with latest amendment as per RDSO Spec No. RDSO/SPN/153/2011 long range working on 110 V- AC 50 Hz complete 3-Aspect suitable for 140 mm dia. post as per Drg.No:SA-23002 A/M [Adv]. Inspection by the Representative of SAIL.

Supply of Signal colour light multi unit as per specification No: IRS: S-26/64 with latest amendment as per RDSO Spec No. RDSO/SPN/153/2011 long range working on 110 V- AC 50 Hz complete 2-Aspect suitable for 140 mm dia. post as per Drg.No:SA-23003 A/M [Adv]. Inspection by the Representative of SAIL.

Supply of Calling On Signal [CLS type] as per RDSO Spec No. RDSO/SPN/153/2011 with Drg.No. SA-24351[Adv], IRS: S-10/78 & S-26/64 complete with 'U' clamps without lenses (Amended up to date). Inspection by the Representative of SAIL.

Supply of 4.6 Mts CLS tubular steel post specification No. IRS: S-6/81 with latest Amnd to suit 140 mm dia base. Inspection by the Representative of SAIL.

Supply of Signal Base 140 mm dia [Type tube] Drg. No. S-2011/M. Inspection by the Representative of SAIL.

Supply of Ladder 4.5 meter for CLS post as per Drg. No. SA: 23153 [Adv] Alt-1, specification No. IRS: S-10/78 (with latest Amendment) consisting of ladder base, platform and guarding, ladder support complete. Inspection by the Representative of SAIL.

Supply of Bracket Off set 140 mm outside dia. for colour light signal post as per IRS:S-10-78 and Drg.No:SA-23080. Inspection by the Representative of SAIL.

Supply of Steel Apparatus case 'large Size' as per Drg. No - CON/SK/1/1/86 and Spec.No. IRS:S-10/78 (adv) with latest amnd. with "E" type lock and key of ward No-32 with handle. Inspection by RITES.

Supply of Steel Apparatus case 'Half Size' as per Drg.No.S&T/CON/BBS/92/90 with 'E' type lock & Key. Ward No. 32. Inspection by RITES.

Supply of junction boxes with covers and terminal plates 24/30 way to suit Drg. No- 23967/1 (as amended up to date) and IRS: S-10/78. This includes supply of PBT terminal. Inspection by the Representative of SAIL.

Supply of Electric key transmitter with different key ward as per requirement as per Drg.No. SA-22601 [Adv], Alt-4 for rotary key transmitter, SA-3577 (M) for Key and IRS:S:21/01. Ward No shall be specified by SAILs. Inspection by RDSO.

Electric point operating machine 143 mm non trailable to operate on 110V DC complete with lock, detector, Point Junction Box along with telescopic pipe and slides for lock and detector - rotary locking Universal type as per specification No: IRS/S/24/2002 with latest amendment Drg. No. RDSO/S-10800 and IRS : S-37/82 Amdt. 3 with Drg. No: RDSO/S: 10910 for motor along with standard tool kit set for every 4 point machines & PBT [6-way] Terminals for Junction Box. Inspection by RDSO for all items except PBT 6 way terminals which shall be inspected by Representative of SAIL. NOTE: Tool kit shall be supplied in a suitable tool box.

Supply of Ground connection set complete suitable for rotary locking type IRS Electric Point Machine as per Drg. No S-3361-62 for 60 Kg rail with insulating materials as specified in IRS/S/24/2002.Inspection by the Representative of SAIL.

Supply of Remote terminal unit with 128 digital & 16 analog inputs with modem as per RDSO spec. No. - IRS-S-99/2006 or latest. Inspection by RDSO. This includes supplying of two Nos. of door sensors for eac Data logger. Inspection by Representative of SAIL.

Supply of double walled corrugated pipe 6 mtr in length, 120 mm outer dia and 103 mm inner dia, with one suitable coupler conforming to RDSO Specification No. RDSO/SPN/204/2011 Version 1.1 Amdt 1 or latest for under ground cable protection . Colour-Orange. Inspection by RITES. Note: If required, the DWC pipe shall be supplied split in two halves.

Supply of Perforated G.I. pipe of 100 mm dia with socket. G.I. pipe of make TATA/JINDAL shall be as per IS: 1239 part-I/2004 Specification for medium gauge and shall be perforated by drilling 7 mm dia holes length wise in zig-zag manner staggered at a distance of 300 mm. Inspection by the Representative of SAIL.

Supply of Permanently lubricated two layer type HDPE duct, outer dia 40 mm, inner dia 33 mm with three end plugs and two couplers for every Km length of pipe in length of 500 m confirming to RDSO Spec. No. RDSO/SPN/TC/45/2013.Rev.2.0 Amendment 2.0 or latest. Inspection by RITES. Note: The HDPE Duct should be pre inserted with 4 mm nylon rope, inside the HDPE Duct.

Supply of split double walled corrugated(DWC) pipes of HDPE confirming to IS:14930,Part-II(ISI marked on pipe)with IP:67 protection of size Minimum outer dia 250mm & minimum inner dia-217mm with out socket /coupler. The HDPE/DWC pipe should have anti-rodent properties and fire resistant TEC specification to GR/DWC/34/01.sept-07 with latest ammendment. Inspection by RITES.

Supply of Relay AC Immune, plug-in type, style 'QNA1', Neutral line, 24V DC 8F/8B contacts, Front and back contacts metal to carbon, complete with plug board, retaining clip and connectors conforming to BRS:931A,IRS: S-60, IRS: S-34, IRS: S-23 (As applicable). Interlocking code: ABDGH. Inspection by RDSO.

Supply of Relay AC Immune, plug-in type, style 'QNA1', Neutral line, 24V DC 12F/4B contacts, Front and back contacts metal to carbon, complete with plug board, retaining clip and connectors conforming to BRS:931A,IRS: S-60, IRS: S-34, IRS: S-23 (As applicable). Interlocking code: ABDFH. Inspection by RDSO.

Supply of Relay Non-AC immune , plug in type, style QN1, neutral line, 24V or 50V DC 8F/8B contacts metal to carbon with plug board, retaining clip and connectors confirming to BRS: 930, IRS: S-34 and IRS: S-23 (As applicable). The interlocking code for this unit shall be ABCDF for 24V and ABDEF for 50V. Inspection by RDSO. NOTE:- Depending upon the EI System, the operating voltage of the relay may change. Accordingly the quantity of relays of different operating voltage needs to be approved by SAIL on request of the OEM of EI System. The contractor shall supply the compatible relays at the same rate.

Supply of Relay Non-AC immune , plug in type, style QN1, neutral line, 24V or 50V DC 12F/4B contacts metal to carbon with plug board, retaining clip and connectors confirming to BRS: 930, IRS: S-34 and IRS: S-23 (As applicable). The interlocking code for this unit shall be ABCDE for 24V and ABCEF for 50V. Inspection by RDSO. NOTE:- Depending upon the EI System, the operating voltage of the relay may change. Accordingly the quantity of relays of different operating voltage needs to be approved by SAIL on request of the OEM of EI System. The contractor shall supply the compatible relays at the same rate.

Supply of Relay Non AC Immune Plug in Type Style QL1 magneticaly latched, Neutral line 24 V DC , 11 F/4B Contacts metal to carbon , complete with plug board, retaining clips and copper annealed connectors conforming to BRS :935A, IRS-S-34, IRS;S-23. Interlocking code: ABDEG. Inspection by RDSO.

Supply of Relay plug-in type Point Contactor relay AC immune plug in type style QBCA1 DC based contactor ,24 V DC with 2 HF ,4B contacts ,Heavy duty metal to carbon front contacts and back contacts metal to carbon ,complete with plug board retaining clip and connectors confirming to BRS : 943 ,IRS S-34, and IRS S -23. Interlocking code for this unit shall be BCEJK. Inspection by RDSO.

Relay plug in type , Style AC-LED: ALL aspect, AC lamp proving Relay unit with in built current transformer type, slow release neutral line relay, 4F/4B contact , front and back contact metal to carbon shall be suitable for working in series with 110V AC, LED signal lamp rated at 15W conforming to RDSO Spec No- STS/E/Relay/AC lit LED/signal/09-2002, Amdt. 1, BRS:941A, IRS:S:34 & IRS:S:23 {as applicable}. The interlocking code for this unit shall be ABDHK. Inspection by RDSO.

Supply of Relay AC Immune, plug-in type, style 'QTA2', DC Neutral track, 9 ohms, 2F/1B contacts, Front and back contacts metal to carbon, complete with plug board, retaining clip and copper annealed connectors conforming to BRS:939A, 966-F2, IRS: S-34, IRS: S-23. Inspection by RDSO. Interlocking code: FGHKX.

Supply of Relay AC Immune, plug-in type, style 'QSPA1', DC, Neutral line, slow to pick up, 24V DC, 8F.4B contacts, Front and back contacts metal to carbon, complete with plug board, retaining clip and copper annealed connectors conforming to BRS:933A, IRS: S-60, IRS: S-34, IRS: S-23 (As applicable). Inspection by RDSO. Interlocking code: ABDEJ.

Supply of Track lead junction box made of glass fibre reinforced plastic Drg. No. SI-10272, Alt-C, specification No. RDSO/SPN/151/1997. Inspection by the Representative of SAIL.

Krone type fibre box indoor surface installation complete with modules and locks suitable for 20 pair. Inspection by the Representative of SAIL.

PVC Switch board cable 20 pair/0.5mm,as per TEC Spec No- GR/WIR-06/03, MAR-2002 with latest Amendment. Inspection by the Representative of SAIL.

Supply of active Lightening Arrester of Class A for building protection as per standard NFC 17-102. It shall work on early streamer emission principle and shall be made of stainless steel with a Time period of 60 micro sec. The dimensions of the device shall be 590X120mm. provision shall be there to test this device if necessary by an external tester. A non resettable type counter shall be supplied to count the number of lightening occurrences. Inspection by RITES. Note: This includes supply of GI mast supplied by OEM as per specification of OEM.

Supply of electrolytic copper tape of 25mmX2mm. or better for connecting class A devise to earth pit. Inspection by Consignee.

Supply of Surge protection Devices complete with all accessories, fixtures as per the following description as per given in technical specification. Inspection by the Representative of SAIL. Make- OBO or similar

Surge Protection Device for 230 V AC input to PC, complete with enclosure and connected wire as per technical specification No:RS-SPD-5.

Surge protection Device for 110V AC input to signals complete with connected wire as per technical specificition No:RS-SPD-7 .

Surge protection Device for 110V DC input to IPS Goomty, complete with connected wire as per technical specificition No:RS-SPD-7.

Surge Protection Device for 24V DC supply complete with connected wire as per technical specification No: TS-SPD-3.

Surge Protection Device for 12V DC supply complete with connected wire as per technical specification No: TS-SPD-3.

Supply of Datalogger complete to spec No- IRS:S:99/2006 AMD. 3 or latest with configuration of 1024 digital inputs and 64 Analog inputs with self power supply system, protocol converters as required etc with networking facilities. Inspection of Data Logger by RDSO & balance item by representative of SAIL. This includes supplying of two Nos. of door sensors for each Data logger. Inspection by Representative of SAIL

Supply of maintenance console (computer and printer) with one set of computer table and chair (Make Godrej) for online tracking and monitoring of station position. Inspection by the Representative of SAIL. minimum Specification: The system shall be provided with following configuration. PC make Dell/HP/Lenovo with 10th generation or latest Intel (R) Core i5 - 10100 processor (3M Cache, 3.6GHz) or latest, 4 GB single channel DDR3 1600MHz - 1DIMM, 500 GB 7200 rpm SATA 6Gb/s Hard drive, Windows 10 Professional or latest with Microsoft office, Monitor 20", 19.5 Inch VIS, E2014H, DVI/VGA, Intel (R) HD Integrated graphics Video card, 16xCD/DVD burner (DVD +/- RW) write to CD/DVD, 32 GB pen drive, 1 KVA UPS with 30 min backup, Quick heal total Security 24 month subscription -EM (ROA) antivirus or similar, NMDL Software module, 3Nos Serial ports. Printer: make EPSON M100/HP laser jet 1020 plus or similar. One year site service warranty in Computer and Printer.

Supply of tag blocks 200 way as per RDSO Specn. No: IRS: S71-87. Inspection by the Representative of SAIL.

Design, Manufacture, Supply of High Frequency Digital Axle Counter Multi-Section type complete system including central evaluator(s), final track clearance relay for each track section, reset boxes, LV boxes, detection points, mushroom housing for the trackside electronics and all other accessories fully wired to the ultimate capacity and fully equipped for all DPs/Nos of detection points (incuding interconnection cards to make common DP or dual DP) this as per RDSO/SPN/176/2013 version 3.0 or latest. conforming to existing yard. Inspection by RDSO. (This includes earthing of track device if required). Note: Unit to be read as DP (Detection point)

Supply of Tool kit for HASSDAC/MSDAC with suitable tool box consist of following or as per OEM list. Inspection by representative of SAIL. a) Fluke meter - 1no. b) Dummy wheel - 1no. c) Adapter Card - 1no. d) Torque wrench - 1no. e) Marking Jig - 1no. f) Card Puller - 1no. g) Set of Spanners - 1 set consisting of the following: i) Screw Driver - 1no. ii) Nut driver - 1no. iii) Fix Spanner - 1no. iv) Nose Piller - 1no. v) IC cutter - 1no. vi) Wire Stripper - 1no. vii) Combination Piller- 1no. viii) Solering Iron - 1no. ix) Soldering wire - 1 roll.

Supply of SDH Add/drop (STM-I) short haul as per DOT Generic specification No: G/SDH-04/01 Feb 95 with latest amendment having in built cross connected capability at junction stations as per network diagram. The equipment shall be able to work upto a fibre length of minimum 60KM and shall be fully equipped to carry 21E1s and shall be usable as a terminal multiplexer where ever required, expandable upto a capacity of 63E1s along with connecting cable and accessories upgradable to STM-4, Inspection by RDSO. Note: - Detail of sub-system to be provided is given in technical specification of tender document.

Supply of 2MB programmable primary digital drop insert multiplexer with conference facility as per IRS-TC-68-2012 ver 0 Amd.1 with latest amendments as on date of opening of technical bid and other technical specification with 30 channels (as per technical specificaton) in Krone modules/DDF modules. Inspection by the Representative of SAIL. Details in sub-system to be provided is given in Technical Specification of Tender documents.

Supply of 48v/50amp SMPS based Power Plant in (2+1) configuration using 3 nos of 48V/25A modules to charge the VRLA battery bank of 48V/200AH with lighting & surge protection as per RDSO specifiction No-RDSO/SPN/TC/23/99(ver-4) Amdt.1 or latest for telecom purpose. Inspection by RDSO.

Supply of Maintenance Free Valve Regulated Lead Acid battery 48V-200AH as per Specn. No.IRS: S: 93/96 (A) (Consists of 24 Nos of 2V-200Ah cells). Inspection by the Representative of SAIL.

Supply of OFC patch cord of 10 mtrs length as Draft RDSO Specn. No. RDSO/SPN/TC/69/2007 or letest for connecting fiber to the equipment. Inspection by the Representative of SAIL.

OFC distribution (management system) box as per RDSO Spec. RDSO/SPN/TC/037-2000, Drg. N0. RDSO/TCDO-170, suitable for 19" rack complete with 24 fibre FCPC/STPC couplers 24 pigtails and suitable tray as per specification and drawing. Make 3M model:8423 or similar (latest version). Inspection by representative of SAIL.

Supply of optical fibre joint closure for straight through joint with modification for 24 fibre as per RDSO Specn No. RDSO/SPN/TC/68/2014, Revision 0.1 Amnd. 1 or latest. Inspection by representative of SAIL.

Supply of Universal Wayside DTMF Control Telephone 2W/4W as per RDSO specification NO.IRS-TC-82/2005 WITH AMENDMENT No.1 or Latest. Inspection by the Representative of SAIL.

Supply of High Power Electronic Cable Route Tracer/ Pipe & Cable locating kit with 36 user configurable Active multi frequency options including 200Hz, 512Hz, 797Hz, 815Hz, 8kHz, 65kHz, 200Hz upto 476.2kHz, passive detection @50Hz for power cables, Radio mode for locating metellic utilities whether energised or not, Current measurement, LCD Display with left-right arrow function; Modes: peak, peak with arrow, pin point peak and null modes, Compass function; Depth measurement, Supply includes locating receiver, Transmitter (Max power : 12Watt) with Li-ion Reachargable Batteries for both Transmitter & Receiver. Battery charger, Induction Signal Clamp 4", supplied in a carry bag. Similar to 3M-Dynate/Radio detection/Stanlay Pathfinder IOC10 Inspection by the Representative of SAIL.

Supply of Fire Extinguisher CO₂ type, Capacity-1 Kg. Inspection by the Representative of SAIL.

Supply of Insulation resistance tester 100 V DC 500 Mega Ohms hand generator type metal body to Spec. no. IS:2992 make WACO. Inspection by the Representative of SAIL.

Supply of Insulation resistance tester 500V DC 500 Mega Ohms hand generator type metal body to Spec. no. IS:2992 make WACO. Inspection by the Representative of SAIL.

Supply of Digital Earth Tester 0.01 to 99 Ohms.In 5 ranges 4 terminals type with all facilities WACO make or similar. Inspection by the Representative of SAIL.

Supply of AC/DC Digital clamp meter Fluke-376 or similar. Inspection by the Representative of SAIL.

Supply of Digital multimeter Fluke-287 or latest higher version with testing lead complete with case and spare set of batteries. Inspection by the Representative of SAIL.

Supply of Magneto Telephone Desk type to Specification No. IRS: TC-36/97 amd 2. or IRS:TC 79/2000 Amdt. 4 as per SAIL requirment. Inspection by the Representative of SAIL.

Supply of Thermo shrink jointing kit for underground cable as per Specn No. IRS: TC-77/2012 [Rev.3] Amd 3. (Cable jointing kit shall be procured from RDSO approved sources only). Inspection by the Representative of SAIL.

Fixing of cable route marker as per drawing in technical specification at a distance of 100 mtrs. Along the trench and at places where the cable route has taken diversion as per instruction of site Engineer, this includes casting of foundation at site and fixing of the marker in the foundation made earlier at site as per railway directives and specifications, this includes proper curing of the structure, All materials required including marker for this like cement, sand 15 mm chips and steel rod of ISI marks should be supplied by the tenderer. Cable Route Marker will be Inspection by the Representative of SAIL.

Supply of High Availability Single Section Digital Axle counter [HASSDAC] system complete with dual sensor as per RDSO Specification number RDSO/SPN/177/2012 ver. 3 or latest. Inspection by RDSO.

Supply of Track feed battery charger input 110VAC, 50 +/-2 Hz with boost and trickle charging for 1 to 4 cells of 80AH, 10A capacity as per spec. No: IRS:S-89/2013 Ver. 1 or latest. Inspection by RDSO.

Supply of Choke coil type-B, impendence 120 Ohms and resistance 3 Ohms DC [For feed end and Relay end], specification No. IRS: S-65/83 Amnd. 3 or latest. Inspection by RDSO.

Supply of Track feed resistance 30 Ohms [2,4,8,16 Ohms] Drg, No. SA-20161- 66 /M and Spec IRS:23/88 (with latest amendment) with PBT base. Inspection by the Representative of SAIL. Track feed resistance should be supplied from only RDSO approved sources.

Supply of low maintenance lead acid secondary cells of capacity 2 V - 80 AH with nuts, bolts, interconnector, ceramic vent plug, battery float etc. Specification No. IRS: S-88/2004 with latest amendment with connectors, nuts, bolts, vent plugs, etc. Inspection by RDSO.

Supply of junction direction 5 lamp type route indicator without lenses, lamps with 3 arms complete as per Drg No-SA-23401-6 (Adv) with latest amendment. Specification No IRS-S-66/84 amnd.1. Inspection by the RITES.

Supply of Earth earth leakage detector12 channel as per RDSO specn. No. RDSO/SPN/256/2002 with latest amendment Inspection by RDSO.

LED signal lighting unit for Main aspect with polycarbonate lens conforming to Indian Railway chromatically standards and RDSO Specn. No. RDSO/SPN/199/2010 REV-1.1 with latest amendment. (This item includes supply of current regulator, Health monitoring unit, audio visual alarm, fuses and other accessories required for fixing). Inspection by RDSO.

For Red Aspect

For Yellow Aspect

For Green Aspect

LED signal lighting unit for shunt signal with polycarbonate lens conforming to Indian Raiwlay chromatically standards and Specn. No. RDSO/SPN/153/2004 REV.-3 with latest amendment (This includes fuses and other accessories required for fixing). Inspection by RDSO.

LED signal lighting unit for Route Indicator with polycarbonate lens conforming to Indian Railway chromatically standards and RDSO Specn. No. RDSO/SPN/153/2011 Rev.4.1 with latest amendment (This includes fuses and other accessories required for fixing). Inspection by RDSO.

LED signal lighting unit for calling on signal with polycarbonate lens conforming to Indian Railway chromaticallity standards and RDSO Specn. No. RDSO/SPN/153/2004 REV-3 with latest amendment. (This item includes fuses and other accessories required for fixing). Inspection by RDSO.

VHF transreceiver set simplex, 25 watt Motorola model no. GM 338 with suitable antenna attached to 12 feet support pipe and 30M RF cable. This shall also include the Power supply for 25W radio (12V/15Amp) with Sealed maint. Free battery (65AH) and one BNC to VHF adapter. This item shall comply to technical specification of tender document. (supplier shall set the frequency given by SAIL. Inspection by the Representative of SAIL.

VHF mobile transreceiver simplex, 5 watt Motorola model no. GP 328 with rechargeable battery. This will include battery charger, one rechargeable spare battery and two spot frequencies for 5W. Inspection by Representative of SAIL.

PVC insulated armoured, unscreened, underground railway signaling copper conductor cable confirming to RDSO specification No. IRS:S-63/2014 (Rev. 4.0) or latest of Sizes: Inspection by RDSO.

6 core X 1.5 sq. mm.

12 core X 1.5 sq. mm.

24 core X 1.5 sq. mm.

PVC insulated armoured, Unscreened, Underground Power cable, 2x25 sq. mm. Stranded Aluminium conductor confirming to RDSO specification IRS:S-63/2014 (Rev.4.0) or latest amendment. Inspection by RDSO.

24 Fibers Armoured Optical Fibre Cableas Per RDSO Specification No. IRS:TC:55-2006 rev. 1 with Amdt. 2. Inspection by RDSO.

Underground jelly Filled 6 Quad Cable for Signalling & Telecom Installations Confirming to IRS: TC-30/2005 (Ver. 1) with latest amendment having 0.9mm dia Copper Conductor. Inspection by RDSO

Cable unarmoured PVC insulated multi core unseathed with plain annealed copper conductor of size 60C X 1 mm dia in accordance with Specification No: IRS-S-76/89 with Amendement -2 or latest. Inspection by RDSO.

Supply of 3 source Auto changeover panel of capacity 150Amps, 230V AC as per RDSO specification No. TI/SPC/ PSI/CLS/0020 (Including A&C slip 1,2,3&4) Inspection by the Representative of SAIL.

Supply of 19" covered rack (2.2m height min), with Glass front door complete with all fittings for housing SDH equipment, primary muxes, DDF, MDF using Krone module, cooling fan and other equipments like runway ladders etc. completely wired and equipped with intergrated protection modules for all channels as per technical specifications and other stipulations of tender document. It should be possible to lock all the equipments with only order wire telephone remaining outside the rack. Inspection by the Representative of SAIL.

Supply of Plastocrate pre-fabricated OFC jointing pits size 1 x 1 x 0.6 meter as per technical specification in the tender document. Inspection by Representative of SAIL

Supply of PSU (Wall mounted 12V, 7AH fully charged, maintenance free valve regulated sealed lead acid stationery battery along with B + charger as per RDSO spec. No. 72/97 (Amd-1) or latest for driving 4W DTMF way station to equipment complete along with copy of maintenance mannual. Inspection by the Representative of SAIL.

Office Chair of continuous arms having plastic cane cover , T.W. Arm rest size 36" x 21" x 22 approx steel tubular frame gauge of the pipes 25mm dia x 18 gauge with olive green colours, Green stove enamelled "Indian Make". Godrej . Inspection by Representative of SAIL.

Office Table of size of table top 1220 mm x 610mm height 750mm with laminated top with 3 drawers on the left hand side and one locker on the right hand side olive brown with Duplicate keys. Olive green colour Make Godrej. Inspection by Representative of SAIL.

Plain storage almirah with 4 adjustable shelves size 1980mm height, 915mm width, 485mm depth, Make Godrej. Inspection by Representative of SAIL.

Airy Revolving and tilting working cushioned adjustable height chair with arm rests, polished black.The chair has plastic caned seat and back on 25 mmround tubular frame. The base is of pressedsheet metal, make Godrej. Width 700 mm,Depth 700 mm, Height 870 mm, Adjustable seat height 410 mm to 520 mm, Colour Grey. Inspection by Representative of SAIL.

Block Instrument - Block proving with digital axle counter (BPAC) conforming to Spech. No. IRS:S-105/2012 (Ver.0 or latest) using Universal Fail Safe Block Interface (UFSBI) for single line and double line operation consisting of the following: a) Universal fail safe block interface (UFSBI) conforming to Specn. No. IRS:5-104/2012 (Ver. 0 or latest) - 2 nos., b) SM Panel (RDSO Drg. No. RDSO/5/32019) with accessories - c) Relay rack with double locking & sealling arrangment. Wiring diagram as per RDSO Drg. No. RDSO/S/32020 - 2 Nos. relays to be supplied with prewired relay rack QN1 = 44 nos. QL1=4Nos., QNA1=12 d) Block Telephone RDSO Spn. No. RDSO/SPN/191/2005 = 2 nos. Inspection by RDSO.

Supply of XLPE insulated PVC sheeated Aluminium conductor armoursed power cable 2Cx70sqmm as per IS709E pt-1-1988.,Inspection by RDSO

Supply of SMPS based IPS to Specn. No. RDSO/SPN/165/2023 with latest version/amendment as per zonal Railway drawing with RDSO standard specification for Six line junction station or above conforming to RE area. with AMP panel and commissioning spare/RDSO approved model. NOTE: 1. This includes LMLA battery bank 2 sets of 200AH each. 2. Copper cable 25 sqmm. Dia as per IS: 694 and grade 1100V for connecting IPS to Battery bank shall be supplied by contractor. IPS unit & battery bank to be inspected by RDSO. Other items to be inspected by the Representative of SAIL.

Diesel Generator set 230 V AC single phase with crompton or Kirlosker quality alternator make , two wall mounting control panels (one main and one subsidisry for remote operation) to start generator by push button battery operated- 30KVA to IRS-S-69/86 . This includes suitable Battery with battery cahrger for charging and 60 liter diesel tank. Inspection by RITES.

Supply of of data anlyzer work station for data inputs & configuration, simulation and functional testing, diagnostics, trouble shooting and commissioning of El system, complete with necessary softwares preloaded as per technical specification. Make HP/Dell/Microsoft Core-17 , SSD 500TB, 8GB RAM, Win11 professional, 3 years on site warrenty, 3 year as antinirus (Quick heal Total security) carry bag hand type. The model to be confirmed by RITES before supply. Inspection by Consignee.

Supply and installation of CAT - 6 UTP, Patch Cord-2 Mtrs, Brand D-Link/MPLEX/AMP/STST emax/Panduit or better. Inspection by Consignee.

Percentage BoQ

BoQ_Ver3.0

eTender No: RITES/PU-BBSR/S&T/SAIL-GUA/OT-12/2025-26, dated: 30.01.2026

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE - C (Drawing & Design) (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bid is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Design of SIP & submission of Three paper copies for approval

For a Six-Line Station

Design of SWRD & submission of Three paper copies for approval

For a Six-Line Station

Design of RCC & submission of Three paper copies for approval

For a Six-Line Station

Design of Cable Route Plan (Distant to Distant) & submission of Three paper copies for approval

For a Six-Line Station

Design of Cable Route Plan (Mid Section) & submission of Three paper copies for approval

For a Six-Line Station

XXXXXXXXXXXX

For a Six-Line Station

Design of Track Bonding Plan & submission of Three paper copies for approval

For a Six-Line Station

Design of Circuit Diagrams consisting of the items as mentioned below & submission of Three paper copies for approval (i) Wiring Diagrams (ii) Relay Disposition Charts (iii ) Contact Analysis and Fuse Particulars (iv) Panel Termination Chart (v) CT Rack Particulars (vi) Input & Output Bit Chart for EI Systems

For a Six-Line Station

Design of Miscellaneous Diagrams consisting of the items as mentioned below & submission of Three paper copies for approval (i) Floor Plan of Relay Room , Battery Room, Power Equipment Room, Data logger room etc. (ii) Power Supply Diagrams along with power supply calculation. (iii ) Earthing Diagram

For a Six-Line Station

Design of Location Box Drawings (Including Contact Analysis, Fuse Particulars etc) and submission of Three paper copies for approval

For a Six-Line Station

Design of Goomty Drawings (Including Relay Disposition Chart, Contact Analysis, Fuse Particulars, CT Rack Particulars and Floor Plan etc) and submission of Three paper copies for approval

For a Six-Line Station

Supply of Original Tracing of SIP after incorporating all the corrections.

For a Six-Line Station

Supply of Original Tracing of SWRD after incorporating all the corrections.

For a Six-Line Station

Supply of Original Tracing of RCC after incorporating all the corrections.

For a Six-Line Station

Supply of Original Tracing of Cable Route Plan (Distant to Distant) after incorporating all the corrections.

For a Six-Line Station

Supply of Original Tracing of Cable Route Plan (Mid Section) after incorporating all the corrections.

For a Six-Line Station

Supply of Original Tracing of Cable Distribution Plan after incorporating all the corrections.

For a Six-Line Station

Supply of Original Tracing of Track Bonding Plan after incorporating all the corrections.

For a Six-Line Station

Supply of Original Tracing of Circuit Diagrams consisting of the items as mentioned below after incorporating all the corrections. (i) Wiring Diagrams (ii) Relay Disposition Charts (iii ) Contact Analysis and Fuse Particulars (iv) Panel Termination Chart (v) CT Rack Particulars (vi) Input & Output Bit Chart for EI Systems

For a Six-Line Station

Supply of Original Tracing of Miscellaneous Diagrams consisting of the items as mentioned below after incorporating all the corrections. (i) Floor Plan of Relay Room , Battery Room, Power Equipment Room, Data logger room etc (ii) Power Supply Diagrams along with power supply calculation. (iii ) Earthing Diagram

For a Six-Line Station

Supply of Original Tracing of Location Box Drawings (Including Contact Analysis, Fuse Particulars etc) after incorporating all the corrections.

For a Six-Line Station

Supply of Original Tracing of Goomty Drawings (Including Relay Disposition Chart, Contact Analysis, Fuse Particulars, CT Rack Particulars and Floor Plan etc) after incorporating all the corrections.

For a Six-Line Station

Supply of Amonia Print of Approved SIP .

For a Six-Line Station

Supply of Amonia Print of Approved SWRD.

For a Six-Line Station

Supply of Amonia Print of Approved RCC.

For a Six-Line Station

Supply of Amonia Print of Approved Cable Route Plan(Distant to Distant).

For a Six-Line Station

Supply of Amonia Print of Approved Cable Route Plan(Mid Section).

For a Six-Line Station

Supply of Amonia Print of Approved Cable Distribution Plan.

For a Six-Line Station

Supply of Amonia Print of Approved Trcak Bonding Plan.

For a Six-Line Station

Supply of Amonia Print of Approved Circuit Diagrams consisting of the items as mentioned below. (i) Wiring Diagrams (ii) Relay Disposition Charts (iii ) Contact Analysis and Fuse Particulars (iv) Panel Termination Chart (v) CT Rack Particulars

For a Six-Line Station

Supply of Amonia Print of Approved Miscellaneous Diagrams consisting of the items as mentioned below. (i) Floor Plan of Relay Room , Battery Room, Power Equipment Room, Data logger room etc (ii) Power Supply Diagrams along with power supply calculation. (iii ) Earthing Diagram

For a Six-Line Station

Supply of Amonia Print of Approved Location Box Drawings (Including Contact Analysis, Fuse Particulars etc).

For a Six-Line Station

Supply of Amonia Print of Approved Goomty Drawings ((Including Relay Disposition Chart, Contact Analysis, Fuse Particulars, CT Rack Particulars and Floor Plan etc).

For a Six-Line Station

Supply of eight sets of Amonia Print of Approved Completion SIP .

For a Six-Line Station

Supply of eight sets of Amonia Print of Approved Completion SWRD.

For a Six-Line Station

Supply of eight sets of Amonia Print of Approved Completion RCC.

For a Six-Line Station

Supply of eight sets of Amonia Print of Approved Completion Cable Route Plan(Distant to Distant).

For a Six-Line Station

Supply of eight sets of Amonia Print of Approved Completion Cable Route Plan(Mid Section).

For a Six-Line Station

Supply of eight sets of Amonia Print of Approved Completion Cable Distribution Plan.

For a Six-Line Station

Supply of eight sets of Amonia Print of Approved Completion Track Bonding Plan.

For a Six-Line Station

Supply of Eight sets of Amonia Print of Approved Completion Circuit Diagrams consisting of the items as mentioned below. (i) Wiring Diagrams (ii) Relay Disposition Charts (iii ) Contact Analysis and Fuse Particulars (iv) Panel Termination Chart (v) CT Rack Particulars (vi) Input & Output Bit Chart for EI Systems

For a Six-Line Station

Supply of Eight sets of Amonia Print of Approved Completion Miscellaneous Diagrams consisting of the items as mentioned below. (i) Floor Plan of Relay Room , Battery Room, Power Equipment Room, Data logger room etc (ii) Power Supply Diagrams along with power supply calculation. (iii ) Earthing Diagram

For a Six-Line Station

Supply of Eight sets of Amonia Print of Approved Completion Location Box Drawings (Including Contact Analysis, Fuse Particulars etc).

For a Six-Line Station

Supply of Eight sets of Amonia Print of Approved Completion Goomty Drawings (Including Relay Disposition Chart, Contact Analysis, Fuse Particulars, CT Rack Particulars and Floor Plan etc).

For a Six-Line Station

Please Enable Macros to View BoQ information