Renovation of House No. 562, Type XI, Sector 11, Chandigarh

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

All kinds of soil

Pipes, cables etc, not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand)

12 mm cement plaster finished with a floating coat of neat cement of mix :

1:4 (1 cement: 4 fine sand)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink without drain board

610x510 mm bowl depth 200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

32 mm dia

Providing and fixing soil, waste and vent pipes :

100 mm dia

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

75 mm diameter :

Centrifugally cast (spun) iron socketed pipe as per IS: 3989

Providing and fixing plain bend of required degree.

100 mm dia

Sand cast iron S&S as per IS : 3989

Providing and fixing heel rest sanitary bend

100 mm dia

Sand cast iron S&S as per IS - 1729

Providing and fixing collar :

Sand cast iron S&S as per IS - 3989

Sand cast iron S&S as per IS - 3989

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

100 mm inlet and 75 mm outlet

Sand cast iron S&S as per IS - 3989

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall

15 mm dia nominal bore

20 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, including making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :

15 mm dia nominal bore

20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work

20 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):

20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

20 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work):

15 mm nominal bore

20 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge.

Cutting holes up to 30x30 cm in walls including making good the same:

With common burnt clay F.P.S. (non modular) bricks

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

100x100 mm size P type

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing of C.P. Steel Grating Heavy (With hole without hole) size 4" i/d (Viking or equivalent with 114gram wt.)

Looking glass mirror 5mm thick of approved make with PVC beading 1-1/4"x3/4" with plastic Hard Board duly fixed on wall with screw/nuts/clips/rod plug

Providing and fixing of G.I. elbow 1-1/4"x3" i/d

Construction of Curb consisting of cement concrete 1:2:4 including cost of sand bajri etc.

Providing and fixing of Bib cock with wall flange, make Jaquar range Continental CON-047N or in same range of AOR of approved make list

Providing and fixing of Long nose Bib cock with wall lange, make Jaquar range Continental CON-107KN or in same range of AOR of approved make list

Providing and fixing of Anglular stop cock with flange make Jaquar range Continental CON - 059KN or in same range of AOR of approved make list

Providing and fixing of Over Head Shower 150x150 mm Single flow Square shape with shower Arm 9" long ISI as per approved make list

Providing and fixing of C.P. Towel Rail 600 mm long complete in all respects make as per approved make list

Providing and fixing of C.P. Towel Ring oval with round flange complete in all respects make as per approved make list

Providing and fixing of C.P. Soap Dish Holder complete in all respects make as per approved make list

Providing and fixing of chinaware Two Piece wall hung EWC complete with Cistern, Seat Cover and Twin Flush Fittings & hydraulic seat cover complete in all respect make

Providing and fixing of C.P. brass Centre Hole Basin mixer of make Jaquar (Continental) CON 167KNB or equivalent approved make in the same range of AOR complete in all respect and to the entire satisfaction of the Engineer-in Charge

Providing and fixing Wall Mixer with provision for Overhead Shower with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges of Make Jaquar Model CON or equivalaent model of approved make

Providing and fixing of Wall hung wash basin with full pedestal complete with C.I./MS brackets 32mm C.P. brass waste as per standard pattern including cutting and painting of brackets and making good the walls Make Cera Model CONCORD( Basin - 1022 & Pedestal 1121) or equivalent model of any other approved make

Providing and fixing kitchen Mixer with wall Flanges of Make Jaquar Model CON or equivalaent model of approved make

Providing and fxing of PVC pipe of 6 kg pressure complete in all respect as per approved make list

Providing and fixing drip seal joints

Please Enable Macros to View BoQ information