Additional works for setup the Drug Control Office_Sl. 3

Supplying and laying true to line and level vitrified tiles of approved brand(size not less than 600mmX600mmX10 mm thick floor skirting etc. using polymerised adhesive (6mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course)(II) With Polymerised Adhesive [6 mm thick] &epoxy grouting materials for filling joints including spacer-2 mm (A) Deep Colour & White

Labour for Chipping of concrete surface before taking up Plastering work.

Supplying, fitting & fixing of Aluminium fixed partion wall of all aluminium sections viz top, bottom and side member, intermediate member, glazing clip made of Aluminium Alloy Extrusions EPDM gusket,cleat, angle screws etc. including labour charges for fitting and fixing of aluminium fixed partition wall with glass / panel board all complete 10-12 Micron thickness Annodizing film. Natural white.For unsupported length of vertical member above 1.50m. height of both ends of vertical member restrained but panel above 0.90 sqm[Note : for estimate purpose construction wing may consider weight of Al-Sections for Partition wall @ 5.0 Kg per Sq.M]

Supplying, fitting & fixing of partly glazed partly panelled or fully glazed single leaf Aluminium swing door of all aluminium sections viz door frame ( top and side frame), shutter( top rail, bottom rail, lock rail, door vertical) , glazing clip made of Aluminium Alloy Extrusions PDM gusket,cleat, angle screws etc. including labour charges for fitting and fixing of aluminium door with door spring,/aluminium hinges, glass / Panel board [Note : for estimate purpose construction wing may consider weight of Aluminium door @ 9.0 Kg per Sq.M]

Providing and fixing exterior quality Aluminium Composite Panel(ACP) wall cladding on existing Al./MS frame work with GI brackets, ACP fixed on the existing frame work by folding the edges ofACP panel(Engraving the rear surface of ACP sheet)with CP angles,cleats and strainless Steel screws forminggrovesat the periphery of ACP panel.Such grooves filled with foam and silicon sealant etc. complete with all materials (but including the cost of silicon sealant), labour, scaffolding and all other incidental charges complete in all respect as per specification and direction of Engineer-in-charge. (Mode of payment is on finished surface area of ACP) (a) 3mm thick (0.25mm Al.+2.5mm LDPE +0.25mm Al. PVDF coating)

Brick work with 1st class bricks in cement mortar (1:6)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (i) With 1:4 cement mortar (a) 20 mm thick plaster Ground Floor

(i) With 1:4 cement mortar : 15 mm thick plaster

Removing old paint from blistered painted surface with application of soda, sajimati or any approved chemical paint remover and exposing the original surface including cleaning and thorough washing to remove all traces of the removing agent including taking outs hutters and refixing the same where necessary

Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick)

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface

Ordinary Cement concrete (mix1:1.5:3) with graded stonechips (20mm nominal size)excluding shuttering and reinfor cement if any, in ground floor as per relevant IS codes (i) Pakur Variety

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(i) Tor steel/Mild SteelI. SAIL/ TATA/RINL(b)Add extra over the rate of ground floor/initial 4 m for each basement floor and each additional floor below/ above ground floor

ALUMINIUM WORKS: D) Supplying Aluminium casted body Butt Hinge (KOBRA type). (Natural white)

(F) Supplying Zinc powered coated star lock

C) Supplying Heavy Duty Aluminium Handle (EBCO Type) (Natural White)

(A) Supplying Aluminium casted body hydraulic door closer as per I.S.I.

(E) Supplying 250mm long Heavy Type Aluminium window Peg Stay (Natural White)

(B)Supplying125mm.Diaacrylichandle for aluminium doorasper approved make & brand. (b) Colour

M.S.works in brackets made from flats, angles, tees etc. to sizes specialy bent, twisted, forged;making holes drilled and fitted to rafter of trusses with necessary bolts, nuts,washer or screws etc. (length of straight not less than 230 mm)

Supplying, fitting and fixing boiling water proof block board conforming to IS:1659-1990 conforming to IS:848 1974 of approved make and brand,fittedand fixed as per design as per direction of Engineer-in-charge.[Excluding the costof supporting frame work and teak wood batten/Lipping].iii) 25mm

Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fitted and fixed with cadmium plated screws:(i) 50 x 45 x 2.5mm.

Anodisedaluminiumdecorativehandle (hexagonal / fluted)of approedquality fitted and fixed complete.(i) 150mm plate x 10mm dia rod x 12mm hexagonal/fluted.

Partition of teak veneer [1mm] as per design fitted and fixed complete(excluding the supporting frame work & necessary teak wood battens): In ground floor

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete,Iron Butt Hinges and M.S clamps.(The quantum should be correted upto three decimals). (c) Sal : Siliguri. 1st floor

Panel shutters of door and window,as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (iii) 35mm thick shutters with 19 mm thick panel of size 30 to 45 cm (b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

Supplying, fitting and fixing M.S.clamps for door and window frame made of flat bent bar,endbifurcated with necessary screws etc.by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) b) 40mm X 6mm, 200mm Length

Iron butt hinges of approved quality fitted and fixed with steel screws,with ISI mark. (vii) 100mm. X 58mm. X 1.90mm.

i) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting. (b) 300mm long.

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (ii) 100 mm grip x 10 mm dia rod.

i)Hydraulic door closer of approved quality as perI.S.I.standard fitted and fixed complete. ii) Godrej Hydraulic door closer fitted and fixed complete (a) Heavy type (I.S.I. size 3)

Priming one coat on timber, plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface if necessary. a) On timber or plastered surface. iv) Two coats (with any shade except white)

ADD GST @ 18.00% ON SUM OF AMOUNT Sl-01 to SL-27

ADD Cess @ 1.00% ON SUM OF AMOUNT Sl-01 to SL 28

Please Enable Macros to View BoQ information