Construction of 1 MLD Sewage Treatment Plant Cum 10 KLD Fecal Sludge Treatment Plant under SBM 2.0 at Illuppur Town Panchayat, Pudukkottai District

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete

Earthwork excavation and refilling for pipeline works having bed width of 1.25m and below on linear measurement basis. (TWAD SOR 23-24 Pg.no . 308)

Earthwork excavation in all soils and sub soils except hard rock requiring blasting with initial lead and lift including re-filling the sides of foundation in layer of 15 cm thick watering , ramming ,depositing the surplus earth in the premises as directed by departmental officers etc., complete asper standard specification.

Removal of Excavated Excess Earth away from the site to 2K.M including loading and transportation charges etc, complete as per standard specification. For 1M3

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers well rammed, watered and consolidated etc. complete complying with standard specification As per PWD SOR 2023-24 Pg no 23

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Supplying and filling in foundation and basement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Providing and laying of coarse aggregate size as below after washing & sieving to make it free from fines & dust.

Passing through 50 mm & Retained on 40 mm sieve

Passing through 20 mm & Retained on 16 mm sieve

Passing through 10 mm & Retained on 6 mm sieve

River fine sand 1-2 mm

Providing and laying Porotherm clay Blocks . The hollow blocks should be of the size 400 x 200 x 150 cms and the opening should be on both the ends

Plain Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Plain cement concrete 1:2:4 mix (One cement two sand and four aggregate) using 20mm ISS metal including mixing, laying, consolidating, curing cost and conveyanc of all materials to site and all labour charges etc., complete as per standard specification

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton.

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

Plane surfaces upto 1.00 m height from G.L

Plane surfaces above 1.00 m height from G.L

Providing centering for sides and soffits of R.C.C.works such as lintels, slab, beams and plain surface etc., complete excluding strutting upto 3.30 M height using mild steel sheet of size 90 c.m x 60 c.m and 10 gauge stifer with M.S. angles of size 25 mm x 25 mm x 3mm laid over silver w.c.wood joints of size 10 c.m. x 6 c.m. spaced at about 90 c.m. c/c and supported by casurina props of 10 c.m. to 13 c.m. dia spaced 75 c.m. centre to centre complying with as per standard specification.

For plane surfaces such as RCC column

For plane surfaces such as RCC Culvert

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers

Providing and laying in position Standardised Concrete Mix M-30 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 400Kg/ cum and maximum water cement ratio of 0.45 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards.

Supplying, fabricating and placing in position TMT bars (Fe 500) for all RCC works as per design given including cost of steel and G.I. binding wire for placing at all depths of excavation, complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel, binding wire and for bar bending)

Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand)) using II class ground moulded bricks of size 9" X 43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 20mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Plastering with cement mortar 1:3,10 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality with necessary welding and painting with one coat of zinc chromite primer and two coats of epoxy painting complete.(As per instruction of site engineer)as per standard specification etc., complete compying with standard specifications

Supplying and fixing in position best quality U.P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with U.P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

110mm UPVC Pipes

110mm UPVC Tee

110mm PVC Elbow

160mm UPVC pipe

160mm UPVC Preforated Pipes

110m dia, PVC air vent pipe with vent cowls

Supplying and fixing in position best quality HDPE soil/ waste pipes of various sizes having ISI mark and providing leakproof joints and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

Lowering HDPE pipes and specials to trench and laying to proper grade and alignment and as directed by the department engineers (TWAD SOR 23-24 Pg.no . 280)

Jointing HDPE Pipes and Specials by butt fusion welding / electro fusion welding joints using fusion equipment as per ISO 21307-2011 and as per IS 7634 (part-2) : 2012 including cost of hire charges for butt fusion equipment power supply arrangements etc., complete as per directed by Engineers. (TWAD SOR 23-24 Pg.no . 291)

Testing of pipes for water supply with hydraulic testing equipment by filling with water (including cost of water) and testing to recommended pressure in convenient stretches and attending the bursts if any occured during the test, excluding the cost of pipes but including other incidential and operational charges etc., complete for the following diametres of pipes.

Geophysical Investigation charges

Drilling of 150mm dia. Deep bore well in hard rock area including labour charges & transportation Charges

Supply & Delivery of 150mm dia P.V.C 6 kg/cm2 casing pipe etc

Supply and delivery of vertical wet type Three phase submersible pumpset (3 HP) discharging any of the following pumpage in lpm against noted head in m suitable for erection into the Bore well of 150mm dia with stainless steel shaft, bronze impeller and stainer with brass screws, water lubricated bearings with sand Guard.-with a duty of 50 lpm x 125M head. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction.The pumpset should be provided with 3m length of suitable size PVC insulated copper flat cable connecting the pumpset & starter. The pumpset should conform to IS 8034/89 and as amended thereafter and bear ISI marking. etc., complete

Supply and devlivery of 3 phase panel board- D.O.L. with two level and auto start as per standard specification PGNO 113

Supply and delivery of 4.00 sqm 3 core coppar flat cable including all materials and all labour charges etc

Supply and delivery of 32 mm UPVC pipe including all materials and all labour charges etc

Supply and delivery of PVC TANK including all materials and all labour charges etc 1000Liters As per IS 12701/1996

Errection of Submercible motar specials in the trench and laying to proper graed and alignment and as Technical officers

Supply and delivery of 40mm pvc pipe including all materials and all labour charges etc

Supply and delivery of 32mm GI pipe including all materials and all labour charges etc

Refilling excated Earth laying of pipes for Pipe Line trench 32 mm pv

Earthwork Excavation in all classes of soil consisting of Hard stiff clay including all labor charges for foundation as per SS20B etc complete.

Supplying of polished cuddapah slab of 20/30 mm thickness including laying to correct alignment as direct by engineer in charge. Includes fixing the slab to support structures.

Supplying and filling of Filling materials

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Paving the floor with Vetrified Marbonite tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement

Dadooing with glassed tiles of 150mm*150mm*6mm size of approved quality and colour set in c.m 1:2 (one cement and two sand) 10 mm thick and pointing with white cement using 0.4 kg /m2 neatly as directed -including cost of all materials and labour charges etc complete as per SS

White washing two coats with freshly burnt shell lime white in colour in all floors including cost of lime and other materials brushes scaffolding charges etc.complete complying with standard specification and as directed. -100sq.m

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors including cost, conveyance of all materials, labour charges therefore etc complete

Supply and fixing of 65mm (21/2") GI pipe Class B of 6m length with 300mmx300mm, 6mm MS base plate, duly welded at the bottaom with concerting with construction of masonry pedestal with suitable MS box to frame work, with door and with lock and key arrangements and with supply and fixing of 50W LED lamp and light fitting with 1m of 32mm GI pipe (Class B). Complete with necessary clamps on the above post with PVC unsheated leads with painting of suitable colour (SD 101A)

Supply and devlivery of 1.1 KV grade 3 core PVC insulated 10 sq.mm Pvc insulated and steel armoured aluminium cable as per IS 1554 and with ISI marking of reputed make

INDOOR FLOOR MOUNTING TYPE CONTROL PANEL supply and installation of electrical control panel cubical construction, fixed floor mounted, non compartmentalized, fabricated of 2mm thick CRCA sheet with dust, vermi proof and powder coated with approved shade. the panel shall have size of 1.4m(L) x1.4m (H) x 250mm (D) to accomodate the individual MCB/ switch gear of each equipment set suitable for operation on 415 V, 3 phase, 50 HZ AC with common single phase preventor individual OLR and individual conductor for each drive. The panel should have encloser protection class IP 54.

Supplying , fixing and wiring earth electrode as per IS:3043 for grounding all equipments using 40mm dia, 2.9mm thick GI pipe 2.5m long buried in a pit with GI funnel with mesh and suitable size reducer fixed on top of the earth electrode. The funnel should be enclosed in a CC chamber300X300X300mm size with a cast iron cover. The pit should be filled with equal proportion of salt and charcoal 150mm around the pipe to complete depth. The connection from the pipe to the conduit etc., is to be established through GI wire/ strip of size as per IS specification 732.using 12mm dia bolts, nuts, washers and checknuts etc. The pipe shall have 16 through holes of 12mm dia.(TWIN EARTHING)PNO 128

Supply and fixing of Synthetic Moulded Compound Box for Street Light etc complete. PWD SOR 2022- 23- page 126

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm]

Wiring with 2X 1.5 sqmm (22/0.3) PVC insulated unsheathed SC.Cu.conductor of 1100v grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A F.T switch inflush with wall, covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light point etc complete SD-25

Supply and fixing of 40 W tube light fittings with copper choke and all other accessories etc., complete complying with standard specification.(S.D 89)

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Supply and fixing of ISA angle for tuss including cost of material conveyance of all mater, fabrication and fixing charges etc. complete as per ISI with rust preventive primer and ready to assemble condition for easy installation at site including dismantling making necessary with power drill to the accessories such as supplying and fixing holdfast, plastic brush inserts receiver runner buttom shock absorbers etc. complete as directed by departmental office

Fabricating, supplying and fixing of pre painted galvanium iron sheets with the following specifications. The materials should be PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be GI base pre painted hot dipped galvanised iron sheet and to be fixed with shelf tapping scres, plastic washer. The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finsh should be terra cotta finish like malabar mangalore tiles. Finish optional matt finish. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required size and making ornamental designs as per the siste condition and as directed by the departmental officers

Fabricating, supplying and fixing of pre painted polycarbonate sheets with the following specifications. The materials should be PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be PC base pre painted hot dipped galvanised iron sheet and to be fixed with shelf tapping scres, plastic washer. The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finsh should be terra cotta finish like malabar mangalore tiles. Finish optional matt finish. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required size and making ornamental designs as per the siste condition and as directed by the departmental officers

Granolthic flooring with PCC 1:2:4 mix using ISS 10 to 12 mm chips including mixing and finishing to a well smoothened surface, watering cost and conveyance all materials and all labour and other incidental charges etc. complet as per standard specification

Supply and run of 2 of 4 Sq mm (56/03) PVC insulated SC unsheathed all conductor of 1100 V on 7/20 GI Bearer Wire for Service connection Mains. (S.D 57)

Supplying and fixing of 16 Amps DB Switch with metel clad of 500 V with fuse and neutral ( Side handle) on Suitable TW Box PWD Earthing. (S.D 141)

Supply and fixing of 1200m A.C. ceiling fan with regulator and all other accessories etc., complete complying with standard specification.(S.D 110)

Supplying and fixing in position of Water closset with 'S' trap including all including dismandling masonry and redoing the same to the original condition

Supplying and fixing of RCC jolly including cost and conveyance of all materials and labour charges etc complete as standard specification.

Supplying and fixing of PVC and GI specials with ISI specification as directed by the departmental officers etc complete.

32mm HDPE Hoose

20mm HDPE Hoose

32mm PVC Pipe

25mm PVC Pipe

25mm Dia GI Pipe B class

20mm Dia GI Pipe B class

15mm Dia GI Pipe B class

25mm Dia GI Union

25mm Dia GI Coupling

25mm Dia GI Elbow

25mm Dia GI Tee

20mm Dia GI Union

20mm Dia GI Coupling

20mm Dia GI Elbow

20mm Dia GI Tee

15mm Dia GI Union

15mm Dia GI Coupling

15mm Dia GI Elbow

15mm Dia GI Tee

15mm SD Nalli

Providing and laying ,spreading and compacting graded stone aggregate to wet mix macadam (WMM ) soecification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 80mm thick high strength type conforming IS 15658-2007 Of rubberized interlocking paver lock in size of minimum compressive strength of 40N mm2 in uniform shape of approved make to be laid in flurring bone pattern with quarry rubbish cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, quarry rubbish cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Labour Charges for erection of Horizontal shaft,centrifugal pumpset (Coupled/Monoblock) in borewell/Open well including fixing of suction pipe and foot valve upto a pipes to the required length with valves, pressure maximum depth of 7 metres and delivery gauges upto the exterior wall of pump room and erectionof panel board consisting of TPIC switches starter,Voltmeter, Ammeter, Capacitor single phasing preventorand laying and jointing the cables and twin earthing asper IE rules including providing bed blocks etc., completeand operating the pumps and trial run for 10 daysincluding signing of completion of reports as required byEB authorities.

Supply and delivery of submercible pump set bore well suttable 50lpm X60 m head including all materials and all labour charges etc (TWAD SOR P98)

Supply and Installation of Danline ropes 20 to 30mm

Supply and installation of submersible centrifugal sewage non-clog pumps 2HP,15m head with10 Cubic Meter delivery per hour with Panel Board and all other fittings

Supply and installation of submersible centrifugal sewage non-clog pumps Pump - 5HP,15m head with 50 Cubic Meters delivery per hour with Panel Board and all other fittings(1 Working + 1 Standby)