GE (N) P/T- 09 OF 24-25 PROVN OF TOILET BLOCK AT HQ SC PUNE PROVN OF PARTITION WITH HDF BOARD ADJACENT TO BUILDING NO 27 AND PROVN OF INTERLOCKING PAVER PATH IN BANGALOW NO 05 AT PG ROAD IN THE AREA OF AGE B/R (C) UNDER GE (NORTH) PUNE

Amount

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out soft/loose soil

Excavating in trenches, n exc1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n.exc 10 sq m on plan and n exc1.5 m in depth and getting out soft/loose soil complete all as directed

M&L for moorum filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as directed

M&L for PCC 1:4:8, type D2 (40mm graded stone aggregate) in foundations,filling and mass concrete complete all as directed

M&L for RCC M-25(Design mix) (using 20mm graded aggregate) as in foundations, including rafts,footings, foundation beams;plinth beams; bases for columns, etc basement slabs,under-reamed piles and mass concrete complete all as directed

M&L for RCC M-25(Design mix) (using 20mm graded aggregate) as in columns, pillars, piers, posts and struts complete all as directed

M&L for RCC M-25(Design mix) (using 20mm graded aggregate) as in slabs supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as directed

-Ditto- all as per item No 7 here in chajjas and like complete all as directed.

-Ditto- all as per item No 7 here in beams cantilevers, bressummers , lintels over 1.5 m span complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter in rough finished surfaces complete all as directed

-Ditto- all as per item No 10 here in before but in suspended slabs such as roof slabs, landing and similar work not exc 200 mm thick complete all as directed.

-Ditto- all as per item No 10 here in before but in sides of pillars, columns posts, sturts complete all as specified and directed.

-Ditto- all as per item No 10 here in before but in roof beams, lintels cantilevers,shelves and similar work etc complete all as specified and directed.

S&F for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as directed

-Ditto- all as per item No 14 here in before but 6mm to 8mm bars for stirrups

M&L for AAC (Autoclave Aerated Concrete) block masonary laid and jointed in cm 1:6 block size 600x200x200mm minimum density of block shall be 550-650 kg/cum incl nominal bond beams to be provided size 200x100mm having two 8mm Fe 500 TMT bars speced with every 1200 mm along the height to be provided. Note - Expenditure of bond beam and steel reinforcement are incl in quoted rate by contractor no extra payment shall be paid to contractor.

M & L for rendering 15mm thick in CM (1:6) on brick masonry internal surfaces of walls finished even and smooth without using extra cement.

M&L for 15 mm thick cement plaster in CM 1:4 on brick or concrete surfaces finishing the surfaces even and smooth without using extra cement mixing with WPC @ 2% by wt of cement all as specified & directed.

M&L for 5 mm thick cement plaster in CM 1:3 on concrete surfaces in ceiling finishing the surfaces even and smooth without using extra cement all as specified & directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of Oil bound distemper of any tint over a coat of primer over a 1 to 1.5 mm thick layer of wall care putty complete all as specified.

M&L for preparation of New plastered surfaces and applying two coats of weather proof exterior emulsion paint ('APEX' brand of Asian or equivalent brand of Berger/Shalimar) over a coat of primer on wall complete all as specified and as directed by Engineer-in-charge..

M&L for preparation of new plastered surfaces of ceiling and applying two coats of Oil bound distemper of any tint over a coat of primer over 1 to 1.5 mm thick layer of wall care putty complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soil complete all as specified and directed

Removing excavated soil n exc 50m and depositing where directed at a level n exc 1.5 m above the starting point.

M & L hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. watered and rolled/rammed to a true surface complete all as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (40mm graded agg) as in sub base of floor complete all as specified and directed by Engr-in-Charge

M/L Non skid ceramic coloured tiles 10mm thick (squar / Rectangular) size of each tile 1200x600 mm in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and incl 20 mm thick screed bed or bedding of layer in CM 1:6 complete all as apecified and directed.

M&L glazed ceramic coloured cladding tiles of size 600 x 300 x 7-8 mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick backing coat in cement mortar 1:4 complete, all as specified.

M&L for cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) 75 mm thick in plinth protection, laid in alternate bays not exc. 3.0m in length, finished surfaces even and smooth without using extra cement including demolition existing concrete and rubbish off the premises complete all as specified

S&F 15 mm bore Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors

S&F 20 mm bore Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors

M&L for cutting chases pinning in brick work for concealing water tubing and making good to facing where required and pointing in cement motar 1:3, cutting n.exc. 10cm girth all as specified.

M&L for 12 mm thick toughned frosted glass as in hinged doors, partitions automatic doors and similar work incl cutting to shape, drilling holes as required incl necessary SS frame work, handles, locking device atc complete all as specified.

S&F aluminium powder coated louvered ventilator with provision of exhaust fan using ‘Jindal” aluminium section or equivalent make as specified including glass 3mm thick ordinary quality, frosted and stainless steel wire mesh 0.36mm dia wire and 1.40mm aperture etc complete all as specified and directed. Section - 63 x 25mm, No- 14001

M&L for vitreous china premium 1st quality jaguar of size 370x670x720 mm UF soft close seat floor mounted wash down water closet EWC white/ivory/off white incl flush cistern fittings, health faucet alongwith two way bibcock and accessaries complete all as specified Make : Jaguar Model No LYS-WHT-38851S 300 UFSMN

M&L Granite (of any type), 18-20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platform,WHB plateform and like in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixer of pigment to match with marble shade including 10mm thick backing of cement plaster in CM 1:3 complete all as specified.

M&L for machine cut 20-25mm thick polished cudappah stone slab as in shelves, partitions, cooking platform below granite stone and like including necessary jointing and pointing in cement mortar and making good to disturbed surface including dismantling of existing stone slab complete all as specified and directed

S&F vitreous china in white colour counter top basin (self-rimming) oval shape of size 550mm x 430mm x 195 mm fixed in position incl waste coupling and PVC wate pipe, 32 mm dia complete make : Parryware model Aquarius, Cat part No-C0466 (SP) or equivalent.

S&F automatic ABS basic hand dryer ( Make : Dolphy Model No DAHD0011) of size 240x230x240mm incl necessary fixing assey complete all as specified and directed.

S&F 5 mm thick bevelled edge looking mirror of size 1.20 m x 0.60 m fixed to wall with SS screws with cap head complete all as specified and directed.

S&F pillar cock swan neck suitable for 15 mm bore pipe long body fancy type brass CP with Capstan head screwed down screwed for iron pipe or brass ferrule quarter turn complete all as specified. Make: Johnson Cat Part No T2804C Magna series or equivalent make.

M&L for 10 mm thick Gymsum board (mositure resistant) seamless as in the ceiling/ linning fixed with counter sunk screws on and incl GI channels frame work of stardard section as per manufacture,s instructions, fixec @ 1.2 m in one direction and 45 cm in center to center in other direction with necessary fixing arrangmentat their junction point at desired heights below roof slab and incl two coats of plastic emulsion paint over a coat of primer on exposed surfaces. (The frame work shall be fixed with the help of GI suspenders of suitable size with the help of sash fasteners and along wall, making good disturbed surfaces, smoothening the gypsum board, POP lining at joints as required complete all as specified and directed. Make : Gyproc-saint Gobain/Armstong/Diaken.

M&L for POP cornices for seamles false ceiling incl necessary hanging arrangments atc complete all as specified and directed.

S&F PVC (SWR) soil, waste and vent pipes, 110 mm dia, in any length , single socketed,jointed with rubber ring joints/adhesive, fixed to wall, with PVC clamps, ISI marked complete all as specified and directed

S&F PVC (SWR) soil, waste and vent pipes, 75 mm dia, in any length , single socketed,jointed with rubber ring joints/adhesive, laid in trenches or in floors, ISI marked complete all as specified and directed

S&F PVC (SWR) bends, 110mm bore, any radius complete all as specified and directed

S&F PVC (SWR) bends, 75 mm bore, any radius complete all as specified and directed

S&F PVC (SWR) branch piece single (single ‘Y’) equal or unequal for 110mm bore PVC pipe complete all as specified..

S&F PVC(SWR) branch piece single (single ‘Y’) equal or unequal for 75mm bore PVC pipe complete all as specified..

S&F for PVC (SWR) junction single (single ‘T’) equal or unequal with access door for 110mm bore pipe complete all as specified..

S&F for PVC (SWR) junction single (single ‘T’) equal or unequal with access door for 75mm bore pipe complete all as specified..

S&F PVC vent cowl of 110mm dia complete all as specified and directed

S&F stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110mm dia of bore complete all as directed

S&F two way bib taps with wall flange quarter turn suitable for 15mm bore pipe long body fancy type brass CP, screwed down screwed for iron pipe or brass ferrule complete all as specified. Make Johnson VIVA new series Cat part No: T4808C or of equivalent make as per Appx 'A' as approved by GE.

S&F hand shower (health faucet) of cast copper alloy chromium plated with 8mm dia, 1.2m long flexible tube and wall hook complete all as specified and directed by Engr-in-charge. Make : CERA -F8030103 or of equivalent .

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed. Make:Paryag/Polytuf

S&F bib cock long nose quarter turn suitable for 15mm bore pipe long body with flange fancy type brass CP with, screwed for iron pipe or brass ferrule complete all as specified. Johnson VIVA new series Cat part No: T4806C or of equivalent make as per Appx 'A' as approved by GE

S&F Stop valve/ Angle valve cast copper alloy (ISI Marked) chromium plated screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia, complete all as specified and directed.

S&F 75mm bore PVC (SWR) floor trap plain with CP grating including jointing with solvent cement to waste pipe fixed in cement concrete type B-1,1:2:4 using 20mm graded stone aggregate complete all as specified.

S & F brass chromium plated soap dish, fixed to wall with CP brass screws, all as specified and directed. Make: Johnson Fusion series Cat part No: T3252C or of equivalent make as per Appx 'A' as approved by GE

S & F Brass Chromium plated towel rail all as specified and directed. Make: Johnson Fusion series Cat part No: T1350C or of equivalent make as per Appx 'A' as approved by GE

S&F brass chromium plated towel ring all as specified and directed. Make: Johnson Fusion series Cat part No: T1351C or of equivalent make as per Appx 'A' as approved by GE

S&F Toilet paper holder of stainless steel, all as specified and directed. Make: Johnson Fusion series Cat part No: T3254C or equivalent

S&F for gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe 20mm bore, ISI marked complete all as specified and as directed.

S&F for gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe 25mm bore, ISI marked complete all as specified and as directed.

S&F corner glass shelf of size 300mm dia and 8mm thick with chomium plated railing fixed with and incl chromium plated bracket complete all as specified.Make:Prayag Cat part No BEA-44 or equivalent

S&F cabinet mirror plastic body for toilet of size 350mmx450mm with 4mm thick looking mirror complete all as specified.Make : Prayag/Polytuff.

S&F vitreous china Urinal, Half stall type, white including brass CP 32mm waste pipe and CP brass spreader for fixing with 15 mm dia pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and incl 60mm long brass screws, pointing around urinal back in cement; flush pipe, grating and union for discharge pipe complete all as specified Make:-Jaquar Cat Part No WHT-13261H or equivalent

S&F Urinal partition incl SS brackets for necessary fixing to wall complete all as directed.Make:-Jaquar Cat part JSE CHR-810UF60H19X or equivalent

S&F rotational moulded polyethylene water storage tank 3 layer white colour water tank, non- toxic effect, algea formation protection (made frome virgin grade of polyethy-lene material which is duly stablized with anti-oxident plastic) of capacity 1000 litres, cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer ,20 mm dia PTMT valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and 20 mm brass stop cock etc complete including dismantling existing water tank all as specified and directed. Make: Sintex, Polycon, Rotex

Material and labour for water proofing treatment to RCC roof slab complete all as specified below and as directed:- (a) Cleaning the roof surface with water (b) Providing 10 mm thick plaster on roof surface in CM (1:4) with using WPC as per manufacturers instructions. (c) Cleaning the plastered surface and applying Oil Based Bituminous primer @ 0.25 ltrs/ Sqm. (d) Applying hot blown bitumen of grade 85/25 @ 1.20 Kgs/ Sqm. (e) Laying APP Modified bituminous membrane 3mm thick weighing not less than 3.50 Kgs/ Sqm with non woven polyester mat as reinforcement with plain finish laid over hot bitumen on roof surface. (f) Applying two coats of bituminous aluminium paint on APP membrane surface. (g) Overlaps (end and longitudinal) shall be finished by torch application. Note No (i) : Overlaps shall be provided as under End Over Laps - 150mm Longitudinal overlaps 100mm. (ii) : Waterproofing Compound shall be measured and paid separtely under relevant item.

Supply only Liquid water proofing compound complete all as specified and as directed.

Supply and fix hume pipe septic of 900 mm Dia and 2.5 m length including necessary excavation in any type of soil , returing filling and removing of soil, fixing of RCC vent pipe min ht 2.0 Mtr and dia of pipe 100 mm , cowl , RCC covers & connecting to the incoming sewer lines and connected to soak pit as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation for shafts, wells, cesspits, manholes, pier holes, pole etc n.exc 10sqm on plan and getting out hard/dense soil complete all as directed

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as directed

Excavating over areas, exc 1.5 m but n exc. 3.0 m deep and getting out in hard/dense soil complete all as directed

M&L for Brickwork with subclass ‘B’ bricks, in circular well steining (any radius) constructed from the base built in CM 1:4 complete all as specified and directed

M&L for Brickwork with sub class ‘B’ bricks in one brick thick honey comb walling, built in CM 1:4 complete all as specified and directed

M&L for loose filling with broken bricks aggregates of gauge 40 to 80 mm in soakage pits, soakage well

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L formwork to edges of concrete fair finish surface exc. 10 cm but n. exc. 20 cm wide (Horizontal or sloping).

M&L for PCC 1:3:6 type C2 (using 40mm graded agg) concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 150mm dia of bore pipe complete all as directed.

M&L for 150mm bore RCC pipes, class NP2 laid and jointed with collars and tested including demolition of existing old one (salt glazed earthware, AC or reinforced pipes etc) set in cement mortar complete all as directed.

M&L for PCC type B-1, 1:2:4 (20mm graded agg) as in copings, kneelers, apex stones,bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as directed

M&L for extra for forming fair finished drain or channel in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc.

S&F in repair for factory made 50mm thick, 950mmx650mm manhole cover with additional frame for fixing, of fixing of pre cast RCC 1:2:4 type B-1 (using 20mm graded agg) finished the surface even and fare including reinforcement MS TMT bars 8mm dia @ 125mm centre to centre bothways and set in CM 1:4 and handles including demolition of RCC (reinforcement cut as required to facilitate demolition) of any description and in any position complete all as specified and as directed.

S&F 18 mm HDF board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws/fevicol to timber frame work complete all as specified. NOTE: This item of work is to be executed upto 4.5m ceiling Height.

S&F 1st class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. NOTE: This item of work is to be executed upto 4.5m ceiling Height.

M&L for 2nd class hardwood plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails/fevicol or brads, bullnosed, splayed, chamfered or rounded on one edge or face, area of section exc. 3.0 sqcm but n. exc. 6 sqcm complete all as specified and directed. NOTE: This item of work is to be executed upto 4.5m ceiling Height.

S&F 18 mm thick CNC design cut plain colour HDF board (Design/Pattern of cutting approved by GE) fixing on wooden frame work including necessary fixing material like nails/screws/adesive/fevicol, beading and scaffolding complete all as specified and directed. NOTE: This item of work is to be executed upto 4.5m ceiling Height.

M&L for preparation of new HDF board surfaces and applying two coats of malamine polish using spray gun including necessary masking and cleaning as required on site complete all as specified and as directed.

M&L for preparation of new wooden surfaces (fillets) and applying two coats of malamine polish using spray gun including necessary masking and cleaning as required on site complete all as specified and as directed.

Dismantling Concrete in ground floors and pavings exc 15 cm thickness but above ground floors complete all as directed.

M & L for 20 mm thick screed bed or bedding layer of mortar in cement mortar(1:6) for laying floor finishes complete all as specified and directed.

M & L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M & L for Machine pressed precast concrete interlocking paver block with gray cement and pigment any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade complete all as specified and as directed

M & L for chequered cement concrete tiles 20cm x 20cm x 25mm thick with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors with grey pigment cement and pigments complete all as specified and as directed.

M&L for Filleting in any position and to any shape in cement mortar 1:4 exc.25 but n exc.50 sq.cm including all mitres, stops, etc. complete all as specified and as directed.

cutting existing 50 mm bore steel tubing in position for altration or additions as per site (each cut measured) in any condition all as specified and directed

Supply and lay 50 mm bore medium grade galvanized pipe with all fitting such as tee, bends, union elbow reducer etc: make: Tata, jindal, Prakash Surya

Supply and fix 50mm bore gun metal gate valve , cast/ ductile screwed down, High pressure with iron wheel handle, screwed both ends for iron pipe or unions Make : leader, Zoloto, GEM, Sant

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade, ISI-694 drawn through in and including heavy duty PVC concealed conduit including all accessories, Metal flush box of suitable module, with earth dolly, covered and including with modular white cover plate & frame after chasing in brick / stone masonry walls etc for accomodating modular switches, sockets, regulators etc including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor along with wiring and connecting to earth dolly, providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed for the following

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

All as per Item No.102 above but with multistranded copper conductor 2.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed multistranded FRLSH cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated multistranded copper conductor 2.5 Sqmm (nominal area) single core FRLSHH cable as earth continuity conductor to common earth and connecting to earth dolly.

S & F for Modular Switch flush type, single pole, one way, 6 Amp, 1 module complete all as specified.

S & F for Modular Socket outlet 2/3 pin combined, 6 Amp, 2 module piano flush type complete all as specified.

S & F for Modular switch, 1 way 16 Amp, 1 module piano flush type complete all as specified.

S & F for Modular Socket outlet 2/3 pin combined, 6/16 Amp, 2 module controlled by one switch piano flush type complete all as specified.

S & F for Ceiling rose, 3 phase/PVC/polycarbonate,surface Bakelite isolated body suitable ISI marked for batten fitting complete all as specified

S & F for LED down light recess mounted luminare, round/square type 18 watts WW as per site requirement with efficiency of 1800 lumens per watt, Series of downlighters with low depth round & larger dia, powder coated white finish with drop down PC diffuser to deliver low glare illumination with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver suitable for office spaces sleek design white finish operating voltage 150 V-270 V AC, 50 Hz all as specified. Make- JAQUAR Cat part No. LNEP01R018XC or equivalent

S & F for wall mounted LED 6 watts (WW)mor more golden colour,3000k with gold colour rendering (CRI>70) picturelight fitting 230 volts with durable alluminium housing and integrated electronic driver connector block etc complete with all acessories internally pre wired and necessary mounting arrangements complete all as specified and directed.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with multistranded copper conductor of size 6.0 Sq. mm nominal area and drawn through PVC non metallic rigid heavy duty concealed conduit as per site requirement and its accessories including one run of PVC insulated with 6.0 Sqmm (nominal area) multistranded copper conductor FRLSH cable as earth wire and connected from DB to DB/ main board complete all as specified and as directed. Note:- two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of heavy duty concealed conduit as per site requirement will be measured as one unit

S & F LED 10 watts batten WW alluminium extruded with decortive end caps complete all as specified and as directed. Make Bajaj cat part No W wH or equivalent make of havell/Philips.

S & F sheet metal enclosure MCB DB SPN 8 way with 100 Amps rated bus bar 240 Volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonary etc and making good of disturbed surface to match the existing colour of wall complete all as specified and as directed

S & F for MCB tripple pole and neutral rated capacity 63 Amps, 415 volts breaking capacity 10 KA complete all as specified and as directed. Make - Schneider/Legrand/L&T/ ABB.

S & F for MCB Single pole rated capacity 5 to 32 A, 240 volts breaking capacity 10 KA complete all as specified and as directed. Make - Schneider/Legrand/L&T/ABB.

Supply and fix plastic body exhaust fan, AC single Phase, working on input voltage 140-285 , of size 250 mm sweep, 1600 RPM, Power consumption16 W with BLDC Motor, blades, frame and louvers provision of 3 core 1.5 sq. mm copper conductor PVC insulated & PVC sheeted flexible wire from ceiling rose/connector to fan including making connections complete all as specified & as directed .

Supply instalation testing and commisioning of ceiling mount auto light occupancy, dual technology, sensor, adjustable of delay timer infra red and ultrasonic detection dia 8 mm IP 20, 3 wire with neutral optimum distance between 2 sensors should be 6 mtr, stand by consumption 0.8w, fixed directly to false ceiling with mounting claws (included) or installed in a battery box depth 50 mm all as specified and directed Note a: All necessary FRLS copper wire to connect complete light of office bldg/ORliving/Messes/toilets etc are deemed to be included in the rates quoted above for motion sensors.

M&L for Maintenance Free Grounding Solution set earthing comprising of High tensile low carbon steel rod of 3 Mts length & 17.2 mm dia with 250micron ( average ) molecularly bonded copper on the outer surface suitable for GI wire dia 4.0 mm along with 50 KG Back-fill compound strictly be a Carbon based conductive concrete type which has a resistivity of less than 0.12 Ohm Mtr. Back-fill compound should be electronically conductive ( Like in metals ) and should not depend on moisture for conduction. Back-fill compound should be environment friendly, should solidify when mixed with water and set like concrete and should not leach / diffuse into the ground. Make: JEF Technology or equivalant in True power earthings, U-PROTEC India Pvt Ltd NOTE :- (a) Rates of boring 3 Mtr for earth electode, GI Wire Dia 4.0 mm upto 7.5 mtr from earth electrode is deemed to be included in quoted rate. (b)On testing, after completion, if the earth resistance < 3 ohms is not obtained, earthing to be rejuvenated at no extra cost till the desired earth resistance is obtained. (c) Test certificate from the OEM has to be produced by the contractor for the material used in earthing (d) Unservicable earthing will be dismantled from above ground level and disturbed ground made good as directed for which cost of earthwork,demolition of cement concrete is deemed to be included in the quoted rate.

Supply and fixing noble electrical aluminium profile /channel for LED light strips, rectangular warm white , (profiles with end cap included)

Supply and fixing flexible LED strip warm white with optimum brightness & unformilty of light for perfect cove lighting each strip fixture length of 5 RM each, including 02 drivers per strip of

M&L for field exploration through bore holes/SPT of dia 150mm by rotary drilling method using hydrolic feed for soil investigation at proposed site through specialist agency with following datas/ specifications:- (i) Exploratory bore holes - 01 Nos upto 5.0m depth from GL and collection of soil sample at every 1m on change of strata upto proposed depth. (ii) Collection of un disturebed samples. (iii) Collection of disturbed samples at different intervals. (iv) to find physical properties of distrubed samples. (v) To find physical properties and strength characterstics of un distrubed samples. (vi) Analysis of SBC and its complete calculation based on N value. (vii) Minimum amd maximum water table. (viii) Interpretation of SBC result analysis and recommendation of type of foundation for framed structure single story building. (ix) Submission of report in 05 copies each.

Note : 1. Rerformance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site.

THE SAIRAM CONSTRUCTIONS (BID ID -3083578)

ANIL CONSTRUCTION CO. (BID ID -3085187)

K.S.JITE AND SONS (BID ID -3086545)

A.S.ENTERPRISES (BID ID -3087966)

N B ENTERPRISES (BID ID -3087134)

L.T Associate (BID ID -3083366)

M/S AKASH ENTERPRISES (BID ID -3087002)

ASMEE ENGINEERING SERVICES (BID ID -3084595)

M/S Eknath agencies (BID ID -3082607)