REPAIR AND REPLACEMENT OF SEWAGE LINES,CLEANING OF MANHOLES SEPTIC TANK, PATH, COMPOUND WALL ,SECURITY FENCE, GRILL AND GATE AT RMS DHOLPUR

Amount

Excavating in trenches not exc 1.5m wide and not exc 1.5 mtr in depth for foundation, etc or for shafts, wells, casepits,manholes,pierholes,etc not exc10 sqm on plan and not exc 1.5 mtr in depth and getting out hard soil/disintegrated rock complete all as specified and as directed

Returning filling including spreading levelling, watering and well ramming in layers n. exc 25cm complete all as specified and as directed

Removal of excavated rock to a distance n. exc 50m and deposited where directed n. exc 1.5m above the starting point complete all as specified and as directed

Cutting existing manholes for connection new drain pipe and making good to pipe and rendering cutting out existing branching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and benching as required internal dia of pipe 150mm complete all as specified and as directed

Demolition and breaking up drain pipes (Salt glazed ware, AC or Re- inforced concrete) set in cement mortar 150 mm dia of pipe complete all as specified and as directed.

M&L for 150 mm internal diameter if pipe Reinforced concrete pipes, class NP-2, laid and jointed complete with colars complete all as specified and as directed

M&L for 150mm internal diameter if pipe Salt Glazed stoneware drain pipes laid in trenches and jointed complete all as specified and as directed

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in, cement concrete 1:4:8 bore of pipe 150 mm dia complete all as specified and as directed

Demolition of cement concrete ( reinforced) in ground floor and paving n.exc 15 cm thickness below or above the ground level complete all as specified and as directed.

M&L Precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone agg) as in landings , cover slabs for man holes etc) chullah hood, chajjas , water troughs mangers ,shelves and similar articles with plain faces ans setting in mortar 1:4 complete all as specified and directed. ( Note: Reinforcement shall be measured seperately under Srl item No 11 & 12 below) complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending spirally for hooping for columns hooking ends and binding with MS wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-0 or Fe-310-0 complete all as specified and as directed.

Ditto all as per Srl item No 11 here in before but 6mm to 8mm dia

Cleaning / clearing of sewage line 100mm to 150mm bore of any description, underground at any depth, removing any type of blockage including desilting, descaling & de-chocking of drains as well as manholes with combined high pressure water jetting cum suction (vaccum) type machine mounted on LCV / HCV and having facilities of high pressure vaccum and provision of hydraulic application through high pressure thermo plastic fiber based water jetting hose and conical round shape nozzle pipe/Cleaning done manually by labourer and flushing after cleaning including removing the same to a non inhabitant Area or buried into ground all as specified and directed . Note: (i) Sewage line cleaned should function smoothly during entire contract period and measurement shall be made only once. (ii) Conractor shall be responsible to clear any further blockage without any extra payment till completion of work. (iii) The cost of this operation / provision shall be deemed to be included in unit rate quoted by the contractor. Also contractor will detail one sweepers daily from the date of commencement of work till completion of the work in the office of Engr-in-Charge to attend complaints as directed by Engineer-in-Charge, the cost of which shall also be deemed to be included in the said item.

Cleaning of blockage EWC/IWC/urinal/bathroom & Kitchen cleaning including gully trap, Nahani trap& removing of sludge/spoil/waste to a distance exc 100mtr & testing of WC block for proper working after cleaning complete all as specified & directed.

Cleaning of Manhole and septic tanks of any capacity ,cleaning sludge from manholes and compartment of septic tank,including intercepting chambers and washing down with water complete and removing the sludge in to the groundby digging trench and covering with earthafter the measurment all as directed . Note-measurment shall be taken on the net fully dried sludge in closely packed stacks on level ground complete all as specified and as directed..

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed..

Non skid coloured ceramic tiles area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 sqm (300x300) 6 to 7 mm thick joint less in floor set in neat cement slurry and pointed with coloured/white cement to match the surface over 15mm thick screed bed in C:M 1:6 complete all as specified and as directed.

M & L Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick CM 1:4 complete all as specified and as directed.

S&L as in repair vitreous china squatting pan (Orissa pattern) water closet (white) size 580mmx440mm with integral foot rests (excluding flushing cistern and flush pipe) complete including connection to trap and flushing pipe antisyphonage pipe etc including provision of PCC (1:5:10) type E-2 in filling complete all as specified

S&L in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm but including brackets, coupling and waste pipe complete all as specified and as directed.

S&F in repairs plastic water closet seat cover (any colours) closed pattern, with mild steel chromium plated or aluminium hinges device complete all as specified and directed.

S&F in repairs 10 Ltrs PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed..

S&F in reapir Hand Shower (health faucet) ABS chrome plated with 8mm dia 1.20 meter long flexible tube and wall hook all as specified and directed.

Cleaning and removing all scale and dirt etc from tanks exc 250 ltr and not exc 500 Ltr and from mouths of circuling pipes, Disconnecting existing tanks, setting aside (or lowering if required) if required reconnecting and re-fixing in position complete all as specified and as directed..

S&F in repair Vitreous China urinal, flat back, white bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed.

S&F in repair PVC waste pipe flexible type suitable for couplings 32 / 40 mm dia and 750 mm long complete all as specified and as directed.. MAKE:- PRAYAG or equivalent make approved by the GE.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Taking down eaves gutter and rain water pipes (any size or pattern) including all fittings, heads, shoes,bends,swan-necks etc including cleaning or refixing or romoval to store complete all as specified and as directed..

S&F PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement complete all as specified and as directed..

S&F PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and as directed.

S&F PVC (SWR) reducer of 110 mm dia complete all as specified and as directed..

S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and as directed..

S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 110 mm dia complete all as specified and as directed.

S&F PVC SWR bends of 110 mm bore complete all as specified and as directed.

S&F PVC SWR bends of 75 mm bore complete all as specified and as directed.

S&F in repair PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps all as specified and directed . Make : Supreme/ Finolex.

S&F in repair PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps all as specified and directed.

Demolition of brick work or stone/bolder masonary, built in cement mortar including all quions, arches, pillars,etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and as directed.

Dismantling structural steel work including doors,gates but excluding framed truss etc complete all as specified and as directed.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding,with and including either hooks,and hinges or steel hanging,door fittings (exclusive of steel sheeting or other covering,running rails and guides) and,hanging; also fastening and,fixing complete all as specified and as directed.

M&L for walling of random rubble, uncoursed well bonded bedded, and solidily hearted, built in cement mortar 1:6 complete all as specified and as directed.

M&L for walling of random rubble, uncoursed well bonded bedded, and solidily hearted, built in cement mortar 1:6 except stone complete all as specified and as directed.

Extra over stone walling for hammer dressing to face stones and dressing,of face beds and joints, as specified, of random rubble walling uncoursed or brought up to courses with maximum depression on face from straight edge held against the dressed surface n. exc. 40 mm, on lime or sand stones complete all as specified and as directed.

M&L for plain cement concrete type B1 1:2:4 (20 mm graded aggregate) as in lintels upto 1.5 m clear sp and other similar bands, plinth courses, string courses,parapets and railings upto 60 cm in height, copings, kneelers, apex stones bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

Raking out joint of pointing to random rubble or polygonal rubble, un-coursed or brought up to courses built in cement mortar complete all as specified and as directed.

M&L for Flush pointing to Random rubble masonry, uncoursed or brought up to courses in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster on stone/brick walls incl raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed.

M&L for rendering 15 mm thick on stone masonary surfaces or surfaces other than fair face of brick work or on one side of lathing in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for two coats of cement base paint on new surfaces of walls, white or tionted including preparation of surfaces complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc. complete all as specified and as directed.

M&L for 40 mm thick Rough dressed sand stone slab flooring, bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 complete all as specified and as directed..

M&L for 40 mm thick Rough dressed sand stone slab flooring, bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3. except stone complete all as specified and as directed.

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 for laying other floor finishes complete all as specified and as directed.

M & L PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation or mass concrete complete all as specified and as directed.

Demolition of cement concrete in ground floor and pavings not exc 15cm thickness below or above ground level, including removal of debries complete all as specified and as directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in plinth protection including finished even and smooth without using extra cement complete all as specified and as directed.

Brick work with sub- class 'B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces of cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and as directed.

Dismantling posts or struts embedded in natural ground/ concrete, brick work, masonry etc (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

M & L PCC 1:3:6 Type C 2 using 40mm graded stone aggregate as in foundation complete all as specified and as directed.

S&F Mild steel work as in hand rails, half round or other stock section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, noising to steps including embeding in concrete and screwing etc wind ties for roof including securingm bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting, etc, and similar work confirming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F in repair Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc as directed (each line of wire to be measured) complete all as specified and as directed.

Restraining, resecuring including making good Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc as directed (each line of wire to be measured) complete all as specified and as directed.

Supply and fix in repair punched tape concertina coil as per IS 4454 and punched tape as per IS 513 deep drawn quality with a galvanising coating thickness of 12 micron minimum having 50 Nos of fixed in postion and secured to both sides of shaped angle iron post with 2.24mm GI wire (concertina coil 450mm dia weighing 7 Kg approx ( +/- 5%) per coil stretchable to 5 to 6m length) complete all as specified and as directed.

M&L preparation of newly steel surface and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Dismantling of chain link fencing of any description from post including line wire etc complete all as specified and as directed.

Supply only chain link fencing made out of mild steel galvanised wire, 50mmx 50mm conforming to IS 2721 complete all as specified and as directed. Note:- Fixing only fencing will be measured and paid separately.

Fixing only chain link fencing of description fixed to steel post with mild steel flat & nut bolt etc complete all as specified and as directed.. Note: (i) Supply only fencing will be measured and paid separately. (ii)Supply and fix mild steel nut bolt, line wire and flat will be measured and paid separately.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long & dia of shank 11 to 15 mm long complete all as specified and as directed.

m/s shanti consruction co

M/S RAJESH MISHRA

M/s K Prashad and Sons