106/EWC(B)/2023-24

Amount

Loading, unloading and safe carriage of the following materials from any Electy. Store Center of Electricity store division of Bareilly zone.to site of work including measuring, weighing, loading, unloading at both ends and proper stacking at safe site.

STP 11Mtr. long

33 KV Pin insulator

33 KV Pin with nut

ACSR dog conductor

33 KV 3x300mm XLPE Cable

33KV 3x300mm cable joitng kit O/D

33KV 3x300mm cable joitng kit S/Th

M.S. Earthing rod of 20x2500mm & 6swg. Earthing wire

Top Channel 125x65x6mm 3200 mm

M.S angle lron 65x65x6mm, 4300mm long for bracing with clamp (5.8 kg. per Mtr.)

T- Off Channel 125x65x1300mm

Erection of the following supports including cutting, making holes, fixing of all types of accessories digging of pits complete in all respect, as per RESSPO drawing. All types of clamps, stone pad, nut, bolt washers would be provided by the contractor.

Cable Exposer double pole structure on S.T. Pole 11mtr long complete with bracing.

End type double pole structure on S.T. Pole 11mtr long complete with bracing.

Concreting of supports in 1:4:8 ratio and plinthing of supports upto 300mm above ground level by using cement ,brick ballast and sand in ratio 1:4:8 as per RESSPO drawing with watering/curing properly upto proper setting of plinthing.All matrial would be provided by the contractor.

Earthing of each S.T Poles of the line is to be done by inserting the MS earth rod (1800x20mm) into soil by hammering and properly fastning with GI wire to each support by nut & bolt. Earthing rod must be 0.15Mtr.above from the plinth of the support. All type nut & bolt would be given by the contractor.

Painting of following supports with one coat of red oxide primer and two coats of aluminum white paint of ISI mark and top danger portion of each support must be painted by providing two coat of Post Office Red Paint (1.5mtr upper portion of support.) Paint and material would be given by contractor to complete the job.

Double Pole of S.T Pole .for cable exposer

Cable laying by drill method in single circuit

Single CKT cable laying by drill method in HDPE Pipe including cost of material 160 mm OD PN-4 PE-80 grade UV stabilized HDPE Pipe as per IS: 4984 (EXCEPT CABLE)

Laying of single circuit 33 KV 3X300 Sq. mm XLPE cable in normal soil by digging of trench 1050 mm deep, 750 mm wide including supply of required material as fine sand, 1st class bricks, stone slab. Inter axial spacing between the two cable should be in between 0.25 m to 0.40m. (All the material required for laying will be supplied by the contractor except 33 KV XLPE cable)

Hoisting of 33 KV 3X300 Sq. mm. XLPE cable on double pole with MS pipe of size 6" dia 3 M long including its jumpering complete with clamps, nuts and bolts.

Fixing of 33 KV O/D / S/ THROUGH

Cable route marker of size 36X12X3 Inch

Making of triangular bridge by using MS electrode, GI strip 50x6mm and GI Pipe 40 mm dia with providing of well type pipe earthing upto 15 Mtr. depth below ground level including welding etc. by boaring process at double pole of railway crossing and newly erected structure including cost of GI pipe of size 40 mm dia 15 mtr. long of ISI mar(all the required material will be supllied by the contractor).

Fixing of danger board & no plate on each location and G.I barbed wire including proper clamping and providing anti climbing device by using including supply of the above items.

M/s Shubham Traders

NATIONAL CONTRACTOR & GENERAL ORDER SUPPLIER

BHARAT ELECTRICAL TRADERS