Provision of shed in front of

Amount

Demolishing cement concrete manually/ by mechanical means including refiling and disposal of material within 50 metres lead as per direction of Engineer - in - charge. 1:3:6 or richer mix

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.: All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.: 1:2:4(1 cement:2 coarse sand: 4 graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in beams, Columns, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.:Thermo-Mechanically Treated bars of grade Fe-500D or more

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.: Hot finished welded type tubes

Provided & fixing precoated galvanised iron tile profile sheets ( size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required .

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 gm per sqm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : North light curves.

Providing and fixing on wall face/floor with clips unplasticised - PVC (SWR type 'A',working pressure 4 Kgf per sq cm ) pipes conforming to IS: 13592 including all fittings like Tee, Bend,cleaning type,Y etc.conforming to IS: 14735,scafolding & jointing with seal ring/ solvent cement and testing of joints complete, conforming to IS: 5382 leaving gap for thermal expansion of make Supreme/Kissan classic/Prince as approved by the Engineer in charge. Single socketed pipes 110 mm diameter

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including making chases and finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

12mm cement plaster of mix: 1:4 (1 cement: 4 fine sand)

Anil S Raul

SANJAY H. AGRAWAL