Institute of Liver and Biliary Sciences (ILBS) at New Delhi

BILL OF QUANTITY

CONSTRUCTION OF RESIDENTIAL ACCOMMODATION FOR FACULTY & STAFF INSTITUTE OF LIVER AND BILIARY SCIENCE (ILBS)_D-1, VASANT KUNJ, NEW DELHI

Code No. DESCRIPTION

SL.NO. UNIT QUANTITY DSR NDSR DSR NDSR

1 EARTH WORK IN EXCAVATION

a NS Credit for sale of earth Cum 45312.44 -150.00 0.00 -6796866.00

Carriage of materials by mechanical transport including loading, unloading and

a 1.1.1 Lime, moorum, building rubbish (for 30 km) Cum 1500.00 455.68 683520.00

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m

in width as well as 10 sqm on plan including getting out and disposal of excavated

earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge:

Earth work in excavation by mechanical means (Hydraulic excavator) /manual

means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10

4 2.6 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m,

surface to be levelled and neatly dressed.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking

excavated or stacked materials.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of

foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited

layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

(Net consolidated area fill volume will be computed from the initial and final levels.

Volume in slopes, embankments etc. will be computed applying appropriate formula,

as per CPWD specification).

Supplying and filling in plinth with sand under floors, including watering, ramming,

consolidating and dressing complete.

Clearing grass and removal of the rubbish up to a distance of 50 m outside the

periphery of the area cleared.

Felling trees of the girth (measured at a height of 1 m above ground level), including

9 2.33 cutting of trunks and branches, removing the roots and stacking of serviceable

material and disposal of unserviceable material.

a 2.33.1 Beyond 30 cm girth upto and including 60 cm girth each 50.00 380.60 19030.00 0.00

b 2.33.2 Beyond 60 cm girth upto and including 120 cm girth each 50.00 1694.40 84720.00 0.00

Transplantation of trees

Transplantation of Treess of the girth from 30cm to 150cm including trimming,

10 NS transposting to the prescribed location and replantation at the location including the each 50.00 20160.00 1008000.00

maintenance of trees up six months.

ANTI TERMITE TREATMENT

Total carried over to summary 31083264.10 -5788866.00

(Rates for all plain cement concrete items described below shall include work from

Basement Level to top of last roof including roof of machine room, Mumty, over head

water tanks and parapets above at all floors and for all heights.

PLAIN CEMENT CONCTRETE

Providing and laying in position cement concrete of specified grade excluding the

cost of centering and shuttering

a 4.1.3 1:2:4 (1 Cement :2 coarse sand : 4 stone aggregate 20 mm ) cum 1543.97 6788.62 10481418.00 0.00

b 4.1.8 1:4:8 (1 Cement :4 coarse sand : 8 stone aggregate 40 mm ) cum 1148.52 5789.60 6649471.39 0.00

Total carried over to summary 17130889.39 0.00

REINFORCED CEMENT CONCRETE WORKS

(Rates for all reinforced cement concrete items described below shall include work

from Basement Level to top of last roof including roof of machine room, Mumty, over

head water tanks and parapets above at all floors and for all heights, required

hacking of the surfaces for smooth plaster. This section covers cast in situ structural

and architectural concrete work).

CEMENT CONCRETE (CAST-IN-SITU)

Providing and laying in position machine batched and machine mixed design mix M-

25 grade cement concrete for reinforced cement concrete work, using cement

content as per approved design mix, including pumping of concrete to site of laying

but excluding the cost of centering, shuttering, finishing and reinforcement, including

admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting

12 5.33 of concrete, improve workability without impairing strength and durability as per

direction of Engineer-in-charge. (Note :- Cement content considered in this item

is @ 330 kg/cum. Excess/ less

cement used as per design mix is payable/recoverable separately).

a 5.33.1 All works upto plinth level Cum 8691.21 7997.30 69506213.73 0.00

b 5.33.2 All works above plinth level upto floor V level Cum 8077.02 9400.85 75930853.47 0.00

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part

Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the

specified cement content used is payable / recoverable separately.

Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement

content considered in M-30 is @ 340 kg/cum)

Providing M-35 grade concrete instead of M-25 grade BMC/ RMC. (Note : Cement

content considered in M-35 is @ 350 kg/ cum)

Centering and shuttering including strutting, propping etc. and removal of form for all

a 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 4747.41 284.85 1352299.74 0.00

Walls (any thickness) including attached pilasters, butteresses, plinth and string

c 5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 34503.05 693.05 23912338.80 0.00

d 5.9.4 Shelves (Cast in situ) sqm 693.05 0.00 0.00

e 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 24838.54 552.05 13712116.01 0.00

f 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 23138.30 733.70 16976570.71 0.00

g 5.9.7 Stairs, (excluding landings) except spiral-staircases sqm 2979.88 622.35 1854528.32 0.00

Extra for additional height in centering, shuttering where ever required with adequate

bracing, propping etc., including cost of de-shuttering and decentering at all levels,

over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan

area to be measured)

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Reinforcement steel

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing

in position and binding all complete upto plinth level.

a 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 954112.18 83.50 79668367.03 0.00

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing

in position and binding all complete above plinth level.

a 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 1166550.27 83.50 97406947.55 0.00

Total carried over to summary 391926584.97 0.00

(Quoted Rates are for all heights, all depths, all levels, including basement to roof

(mumty) & all leads and lifts, including racking curved or circular masonry work,

racking of brick work should be 10mm)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation

7.5 in foundation and plinth in:

a 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 486.90 6157.45 2998062.41

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation

20 6.4 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

a 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 524.46 7590.45 3980887.41 0.00

HALF BRICK MASONRY

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in foundations and plinth in :

a 6.12.2 cement mortar 1:4 (1 cement : 4 coarse sand) sqm 95.24 773.75 73691.95 0.00

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level.

a 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) sqm 74.78 932.10 69702.44 0.00

Extra for half brick masonry in superstructure, above floor V level for every four floors

or part thereof by mechanical means.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third

course of half brick masonry.

Brick work with non modular fly ash bricks conforming to IS:12894, class designation

25 6.34 10 average compressive strength in super structure above plinth level up to floor V

a 6.34.1 Cement mortar 1:4 (1 cement : 4 coarse sand) cum 4512.39 7473.25 33722218.57

Half brick masonry with non modular fly ash bricks of class designation 10,

conformingio IS :12894, in super structure above plinth and upto floor V level.

a 6.45.2 Cement mortar 1 : 4 (1 cement : 4 coarse sand) sqm 15286.29 917.00 14017527.93

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure

27 6.5 above floor V level, for each four floors or part thereof by mechanical means. cum 5279.44 236.66 1249450.75 0.00

Total carried over to summary 57788909.57 0.00

FINISHING WORKS

(Quoted Rate shall be for all heights, depths, levels, leads and lifts and to include

providing Recron polyester fibers in cement mortar at junction RCC and brick / AAC

Block walls and all chasing for electrical & plumbing conduits, pipes etc. for internal

and external plaster works).

CEMENT PLASTER (IN FINE SAND)

28 13.1 12 mm cement plaster of mix :

29 13.2 15 mm cement plaster on the rough side of single or half brick wall of mix :

Providing and fixing 24 gauge and 18 mm mesh size chicken wire mesh at junction

of concrete and brickwork and other locations at all heights including cutting to

required size and side laps of minimum 75 mm and fixing in position with cement and

nails as directed.

EXTERNAL CEMENT PLASTER

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1

31 13.12 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 sqm 46979.36 416.55 19569252.41 0.00

coarse sand) finished rough with sponge.

CEILING CEMENT PLASTER

32 13.16 6 mm cement plaster of mix :

EXTRA FOR WATER PROOFING COMPOUND

Extra for providing and mixing water proofing material in cement plaster work in .Per bag of 50

proportion recommended by the manufacturers kg cement

Extra for plastering exterior walls of height more than 10 m from ground level for

every additional height of 3 m or part thereof.

Extra for plastering done on moulding, cornices or architraves including neat

finish to line and level:

INTERIOR FINISHING

36 13.37 White washing with lime to give an even shade :

a 13.37.1 New work (three or more coats) sqm 26135.91 28.55 746180.23 0.00

Distempering with low VOC washable distemper of approved brand and manufacture

to give an even shade :

New work (two or more coats) over and including water thinnable priming coat with

Providing and applying white cement based putty of average thickness 1 mm, of

approved brand and manufacturer, over the plastered wall surface to prepare the

surface even and smooth complete.

Applying priming coats with primer of approved brand and

manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface

having VOC content less than 50 grams/litre

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound )

content less than 50 grams/ litre, of approved brand and manufacture, including

applying additional coats wherever required, to achieve even shade and colour.

EXTERIOR FINISHING

41 13.45 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming

coat of exterior primer applied @ 2.20kg/10 sqm

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone

additives of required shade:

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of

Special primer applied @ 0.75 ltr /10 sqm

Finishing with Deluxe Multi surface paint system for interiors and exteriors using

Primer as per manufacturers specifications :

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more

a 13.48.2 coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm 152.63 130.25 19880.06 0.00

sqm of approved brand and manufacture

44 13.50 Applying priming coat:

With ready mixed aluminium primer of approved brand and manufacture on resinous

wood and plywood

Painting with synthetic enamel paint of approved brand and manufacture to give

an even shade :

a 13.61.1 Two or more coats on new work sqm 1321.80 121.55 160664.79 0.00

46 13.114 Melamine polishing on wood work (one or more coat). sqm 8764.98 110.75 970721.54 0.00

Total to be carried over the summary 93423426.27 643688.50

DOOR & WINDOW WORKS

(Quoted Rates are for all heights, depths, levels, leads and lifts)

ALUMINIUM DOOR & WINDOW

Providing and fixing aluminium work for doors, windows, ventilators and

partitions with extruded built up standard tubular sections/ appropriate Z sections

and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with

dash fasteners of required dia and size, including necessary filling up the gaps at

junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket

47 21.1 etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat angle, Aluminium snap beading for

glazing / paneling, C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling

and dash fasteners to be paid for separately) :

21.1.1 For fixed portion

Anodised aluminium (anodised transparent or dyed to required shade according to

IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/

pivots and making provision for fixing of fittings wherever required including the cost

of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Anodised aluminium (anodised transparent or dyed to required shade according to

IS: 1868, Minimum anodic coating of grade AC 15)

uPVC DOOR & WINDOW

Providing and fixing factory made uPVC white colour sliding glazed window above

1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built

roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick

galvanized mild steel section made from roll forming process of required length

(shape & size according to uPVC profile), appropriate dimension of uPVC extruded

glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if

required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one

side of extreme panel along with zinc plated mild steel multi point locking having

transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook

(if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable

double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8

mm size for fixing frame to finished wall and necessary stainless steel screws etc.

Profile of frame & sash shall be mitred cut and fusion welded at all corners, including

49 9.147E drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the

gap between frame and adjacent finished wall shall be filled with weather proof

silicon sealent over backer rod of required size and of approved quality, all complete

as per approved drawing & direction of Engineer-in-Charge. (Single / double glass

panes, wire mesh and silicon sealant shall be paid separately).

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension

i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in

higher side shall be accepted but no extra payment on this account shall be made.

Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash

46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /

double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto

Providing and fixing factory made uPVC white colour sliding glazed window upto

1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built

roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick

galvanized mild steel section made from roll forming process of required length

(shape & size according to uPVC profile), appropriate dimension of uPVC extruded

glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy

(white powder coated) touch locks with hook, zinc alloy body with single nylon rollers

(weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame

to finished wall and necessary stainless steel screws etc. Profile of frame & sash

shall be mitred cut and fusion welded at all corners, including drilling of holes for

fixing hardware's and drainage of water etc. After fixing frame the gap between

50 9.147D frame and adjacent finished wall shall be filled with weather proof silicon sealent over

backer rod of required size and of approved quality, all complete as per approved

drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh

and silicon sealant shall be paid separately)

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension

i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in

higher side shall be accepted but no extra payment on this account shall be made.

Two track two panels sliding window made of (small series) frame 52 x 44 mm &

sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead

of appropriate dimension. (Area of window upto 1.75 sqm)

Providing and fixing factory made uPVC white colour sliding glazed door

comprising of uPVC multi-chambered frame with in-built roller track and sash

extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel

section made from roll forming process of required length (shape & size according to

uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded

interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool

pile, zinc alloy (white powder coated) handle with key on one side of extreme panels

along with zinc plated mild steel multi point locking having transmission gear with

keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS

304 grade) body with adjustable double nylon rollers (weight bearing capacity to be

120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and

necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and

51 9.147F fusion welded at all corners, including drilling of holes for fixing hardware's and

drainage of water etc. After fixing frame the gap between frame and adjacent

finished wall shall be filled with weather proof silicon sealent over backer rod of

required size and of approved quality, all complete as per approved drawing &

direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon

sealent shall be paid separately).

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension

i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in

higher side shall be accepted but no extra payment on this account shall be made.

Two track two panels sliding door made of (big series) frame 67 x 50 mm & sash 46

x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double

glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00

9.147C Providing and fixing factory made uPVC white colour casement/

Casement cum fixed glazed door comprising of uPVC multichamberedframe, sash

and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2

mm thick galvanized mild steel section made from roll forming process of required

length (shape & size according to uPVC profile), uPVC extruded glazing beads of

appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges

and one handle on each side of panels along with zinc plated mild steel multi point

locking having transmission gear, cylinder with keeps and one side key, G.I

fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless

steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all

corners, mullion (if required) shall be also fusion welded including drilling of holes for

52 9.147C fixing hardware's and drainage of water etc. After fixing frame the gap between

frame and adjacent finished wall shall be filled with weather proof silicon sealent over

backer rod of required size and of approved quality, all complete as per approved

drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon

sealent shall be paid separately).

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension

i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in

higher side shall be accepted but no extra payment on this account shall be made.

Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x

1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x

a 9.147C.2 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double sqm 260.40 9328.30 2429089.32 0.00

glazing bead of appropriate dimension.(Area of door upto 2.50 sqm)

Providing and fixing factory made uPVC white colour fixed glazed

windows/ventilators comprising of uPVC multi-chambered frame and mullion

(where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick

galvanized mild steel section made from roll forming process of required length

(shape & size according to uPVC profile), , uPVC extruded glazing beads of

appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame

to finished wall, plastic packers, plastic caps and necessary stainless steel screws

etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if

required) shall be also fusion welded including drilling of holes for fixing hardware's

and drainage of water etc. After fixing frame the gap between frame and adjacent

53 9.147B finished wall shall be filled with weather proof silicon sealant over backer rod of

required size and of approved quality, all complete as per approved drawing &

direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant

shall be paid separately).

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension

i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in

higher side shall be accepted but no extra payment on this account shall be made.

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68

a 9.147B.1 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of sqm 456.30 6478.75 2956253.63 0.00

appropriate dimension. (Area upto 0.75 sqm.)

WOODEN DOOR & WINDOW

Providing wood work in frames of doors, windows, clerestory windows and other

frames, wrought framed and fixed in position with hold fast lugs or with dash

fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for

a 9.1.1 Second class teak wood cum 71.17 130183.05 9265127.67

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter

conforming to IS : 14616 and TADS 15:2001 (Part B) fixing with butt hinges of

55 9.6 required size with necessary screws, all complete as per directions of Engineer- in-

charge and panelling with panels of : (Note:- Butt hinges and necessary screws shall

be paid separately)

12 mm thick plain grade -1, medium density flat pressed three layer particle board

a 9.6.1 FPT - I or graded wood particle board FPT- I, IS : 3087 marked, bonded with BWP sqm 2545.18 2636.60 6710621.59 0.00

type synthetic resin adhesive as per IS : 848 :

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I)

decorative type, core of block board construction with frame of 1st class hard wood

and well matched teak 3 ply veneering with vertical grains or cross bands and face

veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth

57 9.23 on all edges of flush door shutters (over all area of door shutter to be measured). sqm 2545.18 401.40 1021635.25 0.00

Providing and fixing wooden moulded beading to door and window frames with iron

58 9.40 screws, plugs and priming coat on unexposed surface etc. complete :

9.40.1 2nd class teak wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm

diameter bolts, nuts and wooden plugs and embedding in cement concrete block

30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel

screws etc. complete :

Providing and fixing bright finished brass tower bolts (barrel type) with necessary

screws etc. complete :

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6

62 9.76 levers and a pair of lever handles of approved quality with necessary screws etc. each 1409.00 712.75 1004264.75 0.00

Providing and fixing bright finished brass hanging type floor door stopper with

necessary screws, etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to

required colour and shade, with necessary screws etc. complete.

a 9.101.1 Single rubber stopper each 1409.00 33.95 47835.55 0.00

Providing & Fixing Chromium plated brass door eye of approved brand &

manufacture of size 35 mm dia suitable for doors upto 40mm thick having clear wide

Providing & Fixing decorative high pressure laminated sheet of plain /

wood grain in gloss / matt/ suede finish with high density protective

surface layer and reverse side of adhesive bonding quality conforming

to IS : 2046 Type S, including cost of adhesive of approved quality.

FD120 Fire rated doors - Painted

Providing and fixing of Hollow metal Insulated fire rated doors as per IS 3614 part-1,

for stability, integrity & insulation. Pressed galvanized steel confirming to IS 277 with

the following specification. Recommended fire door shall be tested to IS 3614 part 2 /

ISO 834-1 Part 1 / BS476 Part 20 & 22, CBRI / Cerifire or third party certified or

equivavelent lab, for maximum rating of 120mins with 30minutes of insulation, in

latched /unlatched condition (if used with deadbolts and pull handles). Labled doors

67 NS with certification shall be with vision glass as a part of complete assembly.

Manufacturer test certificate shall cover doors both single and double leaf and all

doors supplied shall be within the tested specimen, deviation in specification and

sheet thickness other than what is mentioned in the test certificates are not allowed.

Proper label confirming the type of door and the hourly rating is mandatory.

Approved manufacturer Shakti Hormann or approved equivalent.

Door frame shall be single rebate grooved profile of size 125 x 55mm made out of

1.60mm (16gauge) minimum thick galvanized steel sheet. Frames shall be mitered

and field assembled with self tabs. Frames to have inbuild grooved sealing system

and shall be site fitted with fire rated EPDM gasket as standard. All provision should

be mortised, drilled and tapped for receiving appropriate hardware. Frames should

be provided with back plate bracket and anchor fasteners for installation on a

finished plastered masonry wall opening. Frames shall be filled with fire rated puff.

Door leaf shall be 46mm thick fully flush double skin door, insulated with or without

vision lite. Door leaf shall be manufactured from 1.2mm (18guage) minimum thick

galvanised steel sheet. The internal construction of the door should be rigid

reinforcement pads for receiving appropriate hardware. The infill material shall be

high density insulation material. Intumescent seals 15x2mm to be provided all

around the door in addition to the grooved smoke seal. All doors shall be factory

prepped for receiving appropriate hardware and provided with necessary

reinforcement for hinges, locks, and door closers. The edges should be interlocked

with a bending radius of 1.4mm. For pair of doors integrated astragals has to be

provided on the meeting stile for both active and inactive leaf. Vision lite wherever

applicable should be provided as per manufacturers recommendation with a clipon

arrangement. The glass should be 6mm clear borosilicate fire rated glass of relavant

rating of the door.

All doors and frames shall be finished Pure Polyster Powder coated and shall have

passed minimum 500 hours of salt sprey test.

Rate shall include supply and installation of door and hardware as a complete

assembly as mentioned in the door and hardware schedule. Once frame installed

should be filled with PUF as recomended by the manufacturer or engineer.

a 120Mins Fire Rated Door insulated 30minutes Single leaf of size Sqm 232.05 8623.44 2001069.25

Providing & fixing of SS Ball Bearing Hinges of size 100 x 75 x 3mm complet with SS

c NS 3 Point panic bar

d For Double Leaf Door Nos. 65.00 10120.00 657800.00

e NS External lever Handle with locking arrangement Nos. 65.00 2813.00 182845.00

f NS Providing & fixing of door closers of of approved make Nos. 130.00 4740.00 616200.00

Vision Panels 120 mm rating 200mm x 300mm size 6mm thick glass with fixing

h NS Groove seal for frames RM 383.50 250.00 95875.00

Total to be carried over the summary 58059077.28 4014709.25

(Quoted Rates are for all heights, depths, levels, leads and lifts)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

68 11.3 aggregate) finished with a floating coat of neat cement, including cement slurry, but

excluding the cost of nosing of steps etc. complete.

a 11.3.1 40 mm thick with 20 mm nominal size stone aggregate sqm 243.34 498.35 121268.49 0.00

69 11.13 Providing and fixing glass strips in joints of terrazo/ cement concrete floors.

a 11.13.1 40 mm wide and 4 mm thick metre 52.50 metre 29.17 75.15 2192.13 0.00

Providing and laying vitrified floor tiles in different sizes (thickness to be specified

by the manufacturer) with water absorption less than 0.08% and conforming to IS:

15622, of approved make, in all colours and shades, laid on 20mm thick cement

mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm

including grouting the joints with white cement and matching pigments etc.,

Marble stone flooring with 18 mm thick marble stone, as per sample of marble

approved by Engineer-in-charge, over 20 mm (average) thick base of cementmortar

1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry,including

rubbing and polishing complete with :

a 11.23.1 Makrana white second quality sqm 21012.17 3237.80 68033204.03

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be

specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved

make, in all colours, hades, except White, Ivory, Grey, Fume Red Brown, laid on 20

72 11.38 mm thick bed of cement mortar 1:4 (1 ement : 4 Coarse sand), jointing with grey sqm 687.40 996.70 685131.58

cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and

matching pigments etc., complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more

(thickness to be specified by the manufacturer), of 1st quality conforming to IS :

15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on

20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and

matching pigments etc., complete.

Providing and laying Polished Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building, all complete as per

the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick

74 11.56 base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement

slurry and pointing with white cement slurry admixed with pigment of matching

shade, including rubbing, curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed

with grey cement slurry mixed with pigment to match the shade of the slab, including

rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4

Granite stone slabs 18 mm thick in risers of steps, skirting, dado and pillars laid

on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed

with grey cement slurry mixed with pigment to match the shade of the slabs,

including rubbing and polishing complete.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on

12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with

grey cement slurry mixed with pigment to match the shade of the slabs, including

rubbing and polishing complete.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Extra for Kota stone/ sand stone in treads of steps and risers using single length up

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and

prepolished, machine cut for kitchen platforms, vanity counters, window sills,

facias and similar locations of required size, approved shade, colour and texture laid

80 8.2 over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated

with white cement, mixed with matching pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to edges to give high gloss finish etc.

complete at all levels.

8.2.2 Granite of any colour and shade

Extra for providing opening of required size & shape for wash basin/ kitchen sink in

kitchen platform, vanity counter and similar location in marble/ Granite/ stone work,

including necessary holes for pillar taps etc. including moulding, rubbing and

polishing of cut edges etc. complete.

Total carried over to summary 84772042.29 955216.62

FALSE CEILING WORKS

(Quoted Rates are for all heights, depths, levels, leads and lifts)

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in

true horizontal level, suspended on inter locking metal grid of hot dipped galvanized

steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of

main "T" runner with suitably spaced joints to get required length and of size 24x38

mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center

and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm

long spaced between main "T" at 600 mm center to center to form a grid of

1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made

of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm

panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying

82 12.52 false ceiling tiles of approved texture in the grid including, required cutting/making,

opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37

x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4

mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm

spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm

of all Tsections shall be pre-painted with polyester paint, all complete for all heights

as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595

mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100

a 12.52.1 gms/sqm (both sides inclusive) and electro statically polyester powder coated of sqm 20.58 1504.45 30961.58 0.00

thickness 60 microns (minimum), including factory painted after bending.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in

true horizontal level, suspended on interlocking metal grid of hot dipped galvanized

steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of

main "T" runner with suitably spaced joints to get required length and of size 24x38

mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center

and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm

long spaced between main "T" at 600 mm center to center to form a grid of

1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made

of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm

panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying

false ceiling tiles of approved texture in the grid including, required cutting/making,

opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37

x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4

mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm

spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm

of all T- sections shall be pre-painted with polyester paint, all complete for all heights

as per specifications, drawings and as directed by Engineer-in-charge.

8 mm thick fully perforated calcium silicate board made with Calcareous &

Siliceousmaterials reinforced with cellulose fiber manufactured through autoclaving

processto give stable crystalline structure with minimum compressive strength 225

kg/ sq.cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation

of dia.10 mm with minimum perforated area 18 % with non woven tissue on the back

side,having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick

rockwool of48 kg /cum backing.

Providing and fixing false ceiling at all height including providing and fixing of frame

work made of special sections, power pressed from M.S. sheets and galvanized with

zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of

angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at

1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm

dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers

of 25x10x0.50 mm of required length with nuts & bolts of required size and other end

of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the

spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick

bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm,

at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long

G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm

84 12.45 high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to

wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall

screws @ 230 mm interval, including fixing of gypsum board to ceiling section and

perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm

c/c, including jointing and finishing to a flush finish of tapered and square edges of

the board with recommended jointing compound , jointing tapes , finishing with

jointing compound in 3 layers covering upto 150 mm on both sides of joint and two

coats of primer suitable for board, all as per manufacturer's specification and also

including the cost of making openings for light fittings, grills, diffusers, cutouts made

with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of

painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :

2011 (Board with BIS Certification marks)

Providing & fixing false ceiling at all height including providing & fixing

offramework made of special section, power pressed from M.S. sheets

andgalvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS :277

and consisting of angle cleat of size 25mm wide x 1.6mm thick with flangesof 27mm

and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dashfastener 12.5mm

dia x 50mm long with 6mm dia bolts, other flange of cleatfixed to the angle hangers

of 25 x10 x0.50mm of required length with nuts &bolts of required size and other end

of angle hanger fixed with intermediateG.I chanels 45 x15 x 0.90mm running at the

spacing of 1200 mm c/c, to whichthe ceiling section 0.5mm thick bottom wedge of

80mm with tapered flangesof 26 mm each having lips of 10.5mm, at 450mm c/c,

shall be fixed in a directionperpendicular to G.I intermediate channel with connecting

clip made out of2.64mm dia x 230mm long G.I wire at every junction, including fixing

perimeterchannels 0.50mm thick 27mm high having flanges of 20mm and 30mm

85 12.59 long,the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs

at450mm centre, with 25mm long dry wall screws @ 230mm interval, includingfixing

of Calcium Silicate Board to ceiling section and perimeter channels withthe help of

dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing& finishing to a

flush finish of tapered and square edges of the board withrecommended

jointing compounds, jointing tapes,finishing with jointingcompounds in three

layers covering up to 150mm on both sides of joints andtwo coats of primer suitable

for boards, all as per manufacture's specificationand also including the cost of

making opening for light fittings, grills, diffusers,cut outs made with frame of

perimeter channels suitably fixed, all complete asper drawings, specificaton and

direction of the Engineer in charge butexcluding the cost of painting with:

8 mm thick Calcium Silicate Board made with Calcareous & Siliceous

a 12.59.1 materialsreinforced with cellulose fiber manufactured through autoclaving process. sqm 1886.86 1273.05 2402067.12 0.00

Total carried over to summary 7305215.43 0.00

(Quoted Rates are for all heights, depths, levels, leads and lifts)

Granite stone slabs 18 mm thick in risers of steps, skirting, dado and pillars laid

on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed

with grey cement slurry mixed with pigment to match the shade of the slabs,

including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622

(thickness to be specified by the manufacturer), of approved make, in all colours,

shades except burgundy, bottle green, black of any size as approved by Engineer-

87 8.31 in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement sqm 10729.49 1030.30 11054588.44 0.00

mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg

per sqm, including pointing in white cement mixed with pigment of matching shade

Total carried over to summary 11054588.44 10077550.86

(Quoted Rates are for all heights, depths, levels, leads and lifts)

Steel work welded in built up sections/ framed work, including cutting, hoisting,

88 10.25 fixing in position and applying a priming coat of approved steel primer using

structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing,

89 10.26 balcony railing, staircase railing and similar works, including applying priming coat

of approved steel primer.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow

tubes,channels, plates etc., including welding, grinding, buffing, polishing and

making curvature (wherever required) and fitting the same with necessary stainless

steel nuts and bolts complete, i/c fixing the railing with necessary accessories &

90 10.28 stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top Kg 30942.48 575.45 17805850.12 0.00

of the floor or the side of waist slab with suitable arrangement as per approval of

Engineer-in-charge, (for payment purpose only weight of stainless steel members

shall be considered excluding fixing accessories such as nuts,bolts, fasteners etc.).

Supplying and fixing rolling shutters of approved make, made of required

size M.S. laths, interlocked together through their entire length and jointed together

at the end by end locks, mounted on specially designed pipe shaft with brackets,

side guides and arrangements for inside and outside locking with push and pull

operation complete, including the cost of providing and fixing necessary 27.5 cm

long wire springs manufactured from high tensile steel wire of adequate strength

conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling

a 10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover Sqm 70.00 2944.10 206087.00 0.00

92 10.7 Providing and fixing ball bearing for rolling shutters. each 10.00 419.85 4198.50 0.00

Extra for providing mechanical device chain and crank operation for

operating rolling shutters.

a 10.8.1 Exceeding 10.00 sqm and upto 16.80 sqm in the area Sqm 30.00 1106.55 33196.50 0.00

Extra for providing grilled rolling shutters manufactured out of 8 mm dia

94 10.9 M.S. bar instead of laths as per design approved by Engineer-in- charge, Sqm 5.00 668.95 3344.75 0.00

(area of grill to be measured).

Total carried over to summary 25616375.97 0.00

WATER PROOFING WORKS

(Quoted Rates are for all heights, depths, levels, leads and lifts)

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with

SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75

on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand

mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix

of white cement & marble powder in ratio of 1:1, including rubbing and polishing of

the surface upto 3 cuts complete, including providing skirting upto 150 mm height

along the parapet walls in the same manner.

Providing and laying roof insulation with 40 mm thick impervious sprayed, closed

cell free Rigid Polyurethane foam over deck insulation conforming to IS - 12432 Pt.

III (density of foam being 40-45 kg/ cum), over a coat of polyurethane primer applied

@ 6-8 sqm per litre, laying 400 G polythene sheet over PUF spray and providing a

wearing course of 40 mm thick cement screed 1:2:4 (1 cement : 2 coarse sand : 4

96 12.56 stone aggregate 20 mm nominal size) in chequered rough finish, in panels of 2.5 m x sqm 2679.04 1412.20 3783340.29 0.00

and embedding with 24 G wire netting and sealing the joints with polymerized

all complete as per direction of Engineer-in-Charge

Providing and fixing of external thermal insulation and composite system with

First layer of self-extinguishing type Expanded Polystyrene (EPS) insulation

boards of 120 mm thick ( max 1mX0.5m section), confirming to IS 4671:1984,

having thermal conductivity of 0.034 W/mK, (measured as per IS 3346-1980),density

of 20-24 kg/m³ measured as per IS 5688-1982, Fire retardant property

self-extinguishing type as per EN 13501-1, bonded with special polymer modified

cementitious adhesive confirming to EOTA ETAG 004 (European Technical

Approval) formulated to bond polystyrene insulation boards to typical mineral

substrate (according to ETAG 004) and Polypropylene mechanical fasteners

with plastic pin confirming to EOTA ETAG 014 (European Technical Approval)

having dia 10mm & L=200mm on finished level wall and the junction between

two adjacent EPS boards to be sealed with low expansion moisture cure

Polyurethane Foam. Second layer consists of Fiberglass mesh covered with

97 26.67 alkali-resistant coating, mass per unit area > 145 gm/m², mesh size: 3.9x4.0 mm sqm 2679.04 3366.60 9019256.06 0.00

±10% embedded in special polymer modified cementitious Base Coat with

hydrophobes and the corners will be protected with Corner-beads with alkaliresistant

mesh wings at least 10 cm wide, mesh mass per unit area min 145 gm/

m². The surface will be levelled, finished, made smooth complete in all respect

as per manufactures specification and as per directions of Engineer-in-Charge.

98 22.14 Grading roof for water proofing treatment with

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm

Providing and laying water proofing treatment to vertical and horizontal surfaces of

depressed portions of W.C., kitchen and the like consisting of:

(i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing

compound conforming to IS 2645 in recommended proportions including rounding off

junction of vertical and horizontal surface.

(ii) 2nd course of 20 mm cement plaster 1:3 (1 cement: 3 coarse sand) mixed with

water proofing compound in recommended proportion including rounding off junction

of vertical and horizontal surface.

(iii) 3rd course of applying blown or residual bitumen applied hot at 1.7kg. per sqm of

(iv) 4th course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet

should be 100 mm wide and pasted to each other with bitumen @ 1.7kg/sqm)

Providing and applying integral crystalline slurry of hydrophilic in nature for

waterproofing treatment to the RCC structures like retaining walls of the basement,

water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels

/ subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts

integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts

integral crystalline slurry : 1 part water) for horizontal surfaces and applying the

same from negative (internal) side with the help of synthetic fiber brush. The material

shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing

100 22.23 permeability of concrete by more than 90% compared with control concrete as per

DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The

crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm.

The work shall be carried out all complete as per specification and the direction of

the engineer-incharge.The product performance shall carry guarantee for 10 years

against any leakage.

For vertical surface two coats @ 0.70 kg per sqm-Retaining Wall/Water Tank Wall

For horizontal surface one coat @1.10 kg per sqm.-Below Raft/ Water Tank Floor

Providing and laying water proofing treatment on roofs of slabs by applying

cement slurry mixed with water proofing cement compound consisting of applying:

(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed

with water proofing cement compound @ 0.253 kg/sqm.

(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps

of joints of fibre cloth should not be less than 10 cm.

(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm

mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @

101 22.6 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for sqm 7378.32 523.05 3859230.28 0.00

48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked

into groove in parapet all around.

(d) fourth and final layer of brick tiling with cement mortar (which will be paid for

separately.For the purpose of measurement the entire treated surface will be

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100%

polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent

102 14.92 touch by heating the membrane by Butane Torch as per manufactures sqm 7378.32 99.75 735987.42 0.00

recommendation.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

103 12.21 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 0.00

(1 cement : 3 fine sand) as per standard design :

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size)

over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1

cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making

and finishing the outlet complete.

Total carried over to summary 34685544.40 0.00

MISCELLANEOUS WORKS

Providing & fixing of 50mm thick GRC Jali with necessary supports, as per approved

sample, including all necessary arrangements & hardware- fittings,

105 NS Item fixtures,scaffolding and edge finish etc., complete as per design, details &

specification, or as per directions of Engineer-in-charge.

Total carried over to summary 0.00 5824215.20

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from

batching plant. The ready mixed concrete shall be laid and finished with screed

board vibrator , vacuum dewatering process and finally finished by floating, brooming

with wire brush etc. complete as per specifications and directions of Engineer-in-

106 16.75 charge. (The panel shuttering work shall be paid for separately). cum 1657.28 8663.05 14357099.50 0.00

(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less

cement used as per design mix is payable/ recoverable separately).

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne

capacity after excavating earth to an average of 22.5 cm depth, dressing to camber

107 16.1 and consolidating with road roller including making good the undulations etc. and re- sqm. 4736.00 156.75 742368.00

rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

16.3 Supplying and stacking at site.

a) 16.3.2 63 mm to 45 mm size stone aggregate Cum 355.20 1535.65 545462.88

b) 16.3.3 53 mm to 22.4 mm size stone aggregate Cum 355.20 1749.75 621511.20

c) 16.3.7 Stone screening 11.2 mm nominal size (Type B) Cum 236.80 1978.50 468508.80

Laying, spreading and compacting stone aggregate of specified sizes to WBM

specifications in uniform thickness, hand picking, rolling with 3 wheeled road/

vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying

and brooming requisite type of screening / binding material to fill up interstices of

coarse aggregate, watering and compacting to the required density .

Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement

concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal

size) over 75mm bed of dry brick ballast 40 mm nominal size, well rammed and

consolidated and grouted with fine sand, including finishing the top smooth etc.

complete and as per direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade

cement concrete in position to the required line, level and curvature, jointed with

cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without

grooves (thickness of joints except at sharp curve shall not to more than 5mm),

110 16.69 including making drainage opening wherever required complete etc. as per direction Cum 60.11 8376.15 503490.38

of Engineer-in-charge (length of finished kerb edging shall be measured for

payment). (Precast C.C. kerb stone shall be approved by Engineerin- charge).

Providing and laying in position bitumen hot sealing compound for

expansion joints etc.

Using grade ‘A’ sealing compound. per cm depth

Providing and applying 2.5 mm thick road marking strips (retroreflective)

of specified shade/ colour using hot thermoplastic material by fully/ semi automatic

thermoplastic paint applicator machine fitted with profile shoe, glass beads

dispenser, propane tank heater and profile shoe heater, driven by experienced

112 16.62 operator on road surface including cost of material, labour, T&P, cleaning the road Sqm 700.00 607.30 425110.00

surface of all dirt, seals, oil, grease and foreign material etc. complete as per

direction of Engineer-in-charge and accordance with applicable specifications.

Total carried over to summary 18900511.80 0.00

ELECTRICAL WORK

Sub Head 1: point wiring

Wiring for light point/fanpoint/exhaust fan point/call bell point with 1.5 sq.mm.FRLS

PVC insulated, copper conductor single core cable in surface/recessed medium

113 1.1 class PVC conduit, with modular switch, modular plate, suitable GI box and earthing

the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable

etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell

point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper

114 1.55 conductor single core cable in surface/ recessed PVC conduit, and earthing the point

with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated, copper

conductor, single core cable in surface/recessed medium class PVC conduit, with 2

115 1.11 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 Point 73.00 1057.00 77161.00 0.00

sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for light / power plug with 2x4 sq.mm. FRLS PVC insulated, copper

conductor, single core cable in surface/recessed medium class PVC conduit along

with 1 No. 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop

earthing as required

Wiring for circuit/ submain wiring along with earth wire with the following sizes of

117 1.14 FRLS PVC insulated copper conductor, single core cable in surface/recessed

medium class PVC conduit as required

Supplying and drawing following pair 0.5 sq mm FRLS PVC insulated annealed

118 1.18 copper conductor, unarmored telephone cable in the existing surface/recessed steel/

PVC conduit as required.

Supplying and drawing following pair 0.5 sq mm FRLS PVC insulated annealed

119 copper conductor, armored telephone cable in the existing cable tray/surface as

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper

conductor PE insulated, shielded with fine tinned copper braid and protected with

PVC sheath in the existing surface/recessed steel/PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit alonwith the

121 1.21 accessories in surface/recess including cutting the wall and making good the same

in case of recessed conduit as required :

Supplying and fixing metal box of following sizes (nominal size) on surface or in

122 1.22 recess with suitable size of phenolilc laminated sheet cover in front including painting

etc. as required

Supplying and fixing following modular switch /socket on the existing modular plate &

123 1.24 switch box including connections but excluding modular plate etc. as reuired.

a 1.24.6 Telephone socket outlet Each 520.00 119.00 61880.00 0.00

b 1.24.7 TV antenna socket outlet Each 518.00 119.00 61642.00 0.00

Supplying and fixing two module stepped type elctronic fan regulator on the existing

124 1.25 modular plate switch box including connection but excluding modular plate etc. as Each 777.00 342.00 265734.00 0.00

Supplying and fixing following size/modules, GI box alongwith modular base & cover

125 1.27 plate for modular switches in recess etc as required. ( for telephone, TV outlets, Bell

Supplying and fixing GI box with modular plate and cover in front on surface or in

recess, including providing and fixing 3 pin 5/6 amps. modular socket outlet and 5/6

amps. Modular switch, connections etc. as required. (For light plugs).

Supplying and fixing GI box with modular plate and cover in front on surface or in

127 1.32 recess, including providing and fixing 6 pin 5/6 & 15/16 amps. modular socket outlet No. 1337.00 495.00 661815.00 0.00

and 15/16 amps. Modular switch, connections etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and

128 1.35 shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all Each 4822.00 98.00 472556.00 0.00

accessories including connections etc. as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden

block including connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete

Installation, testing and commossioning of ceiling fan, including wiring the down rods

of standard length (upto 30cm) with 1.5 sq.mm. FRLS PVC insulated, copper

conductor, single core cable, incuding providing and fixing phenolic laminated sheet

cover on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including making good the

damage, connection, testing, commissioning etc. as required.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan

clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with

its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/

M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the

corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard

Supply, installation, testing and commissioning of Main Distribution Frame Krone

type with lockable box as required

Total:Subhead 1 17895784.75 266437.00

135 Subhead 2 : Distribution Boards and LT Panels

Supplying and fixing following way, single pole and neutral,sheet steel, MCB

distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole and neutral, sheet

steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned

137 2.4 copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing 5 amps. to 32 amps. rating, 240/415 volts, 'C' curve,miniature

circuit breaker suitable for inductive load of following poles in the existing MCB DB

complete with connections, testing and commissioning etc. as required

b 2.10.3 Double pole (incomer ) Each 7.00 556.00 3892.00 0.00

Supplying and fixing single pole, blanking plate in the existing MCB DB complete etc.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB

140 2.13 DB complete with connections, testing and commissioning etc. as required :

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V,

residual current circuit breaker (RCCB), having a sensitivity current 30mA in the

existing MCB DB complete with connections, testing and commissioning etc. as

Supplying and fixing of following rating, 415 volts, 'C' curve,miniature circuit breaker

142 A/R on MR suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required

143 A/R on MR MAIN LT PANEL

Supply, installation, testing and commissioning of M.V. cubicle type totally enclosed

floor mounted free standing type, dust, damp and vermin proof Panel complete with

incoming and outgoing switchgears and meters, M.V. danger notice plate,

interconnections with suitable capacity aluminium leads/solid aluminium strips, rods,

connection of incoming and outgoing cables with thimbles, powder coated painted

complete as per drawing and technical specifications as required.

Note: Panel shall be suitable for tube sensing based CO2 gas flooding system

INCOMERS B & D: FROM 2 Nos. 1250 kVA TRANSFORMER

Each Incomer have following

1 No. 2000A, 415V, 50kA rupturing capacity, EDO FP Air Circuit Breaker with

microprocessor release and opration counter.

1 set of indicating lamps to indicate ON, OFF and TRIP for breaker

1 Set of phase indicating lights LED type with control of 2A SP MCB

1 Set 0-2000A ammeter with Class-1 2000/5A CTs

1 No. Multifunction meter (MFM) with Class-1 2000/5A CTs and RS 485 port

1 No. CL-1 15VA 2000/5A CTs for APFCR

1 Set of over/under voltage realy with CL-5P10 15VA 2000/5A CTs contacts for trip

1 no.surge protection device Type-1/Class-B suitable for 50kA fault current

1 No.25 kVAR Fix type Capacitor bank each 63A, 415V, Ics=Icu=35kA rupturing

capacity, TPN, MCCB with ON-OFF push buttons and set of indicating lights.

INCOMERS A & E : FROM 2 Nos. 320 kVA DG SETS

Each incomer have following

1 No. 630A, 415V, 50kA rupturing capacity, EDO FP Air Circuit Breaker with

microprocessor release and opration counter.

1 set of indicating lamps to indicate ON, OFF and TRIP for breaker

1 Set of phase indicating lights LED type with control of 2A SP MCB

1 Set 0-630A ammeter with Class-1 630/5A CTs

1 No. Multifunction meter (MFM) with Class-1 630/5A CTs and RS 485 port

1 Set of over/under voltage realy with CL-5P10 15VA 630/5A CTs contacts for trip

1 no. surge protection device Type-1/Class-B suitable for 50kA fault current

1 Set Reverse power relay with CL-5P10 15VA 630/5A CTs contacts for trip and

2500A Phase and1250A Neutral TPN busbars of aluminium with colour coded heat

shrinkable sleeves and with SMC/DMC supports at every 600mm intervals and at

800A TPN busbars of aluminium with colour coded heat shrinkable sleeves and with

SMC/DMC supports at every 600mm intervals and at both ends

BUS COUPLERS : C

1 No. 2000A, 415V, 50kA rupturing capacity, EDO FP Air Circuit Breaker as B/C

without protective releases but with Under voltage release and ON-OFF indication

Interlocking system with electrical Interlocking between Three Incomers and one

buscoupler for operation, so that at any time no two different power supply shall be

ON & Conected together as per interlocking scheme as shown on SLD drwing No.

Programmable Logic Controller (PLC Based AMF cum load Mangement Control

Panel) to control of 2 Nos. D.G. Sets. incomers and 1 No. Tranformer incomer and

1 No. Bus Coupler with each provided the following:

1. 3-way On/Off Master/ self selector switch for Auto Load Mangement by auto

start/stop of required Gensets.

2. Complete AMF Operation

3. Protection for Low level lub oil (LLOP), High Water Temperature (HWT), Three

Times start on failure lock the D.G., U/V, O/V, U/F & O/F.

4.Suitable Nos. of Indication Lights, Push Buttons, Selector Switches, Battery

Charger CVCC type with auxiliary relays and Auxliary contactors etc. complete as

Note : All outgoing feeders shall have ammeter, inbuilt selector switch and set of

Class-1 CTs, ON indicating lamps & Phase spreaders.

1 No. 800A, 415V, Ics=Icu=35kA rupturing capacity, TPN MCCB with

microprocessor releases, OC/SC protection and operation counter for 400 kVAR

capacitor panel

2 Nos. 630A, 415V, Ics=Icu=35kA rupturing capacity, TPN, MCCB with

microprocessor releases,extended rotary handle

2 Nos. 315A, 415V, Ics=Icu=35kA rupturing capacity, TPN, MCCB with

microprocessor releases,extended rotary handle

2 Nos. 250A, 415V, Ics=Icu=35kA rupturing capacity, TPN, MCCB with extended

4 Nos. 100A, 415V, Ics=Icu=35kA rupturing capacity, TPN, MCCB with extended

2 Nos. 63A, 415V, Ics=Icu=35kA rupturing capacity, TPN, MCCB with extended

1 No. 315A, 415V, Ics=Icu=35kA rupturing capacity, TPN, MCCB with

microprocessor releases,extended rotary handle

2 Nos. 400A, 415V, Ics=Icu=35kA rupturing capacity, TPN, MCCB with

microprocessor releases,extended rotary handle

2 Nos. 160A, 415V, Ics=Icu=35kA rupturing capacity, TPN, MCCB with extended

4 Nos. 100A, 415V, Ics=Icu=35kA rupturing capacity, TPN, MCCB with extended

3 Nos. 63A, 415V, Ics=Icu=35kA rupturing capacity, TPN, MCCB with extended

MAIN LT PANEL AS DESCRIBED ABOVE Each 1.00 2500000.00 0.00 2500000.00

144 A/R on MR CAPACITOR PANELS

Supply, installation, testing and commissioning of factory made Automatic Power

Factor Control Panel of following KVAR capacity having single phase MPP type, self

healing, long life low loss capacitor (loss shall not exceed 0.2W/KVAR) filled with

suitable capacitor grade oil & housed in Aluminium cane mounted on modular racks

of maximum 100 kVAR capacity and minimum 10kVAR and having current limiting

contactor circuit to supress switching inrush current to improve capacitor life. The

system shall have multistep microprocessor based power factor controller provided

in the command module having two set points for target P.F setting, automatic

adjustment of C/K, Digital PF display. The system shall be provided with each

capacitor bank Incoming isolating TP MCCB/MCB, capacitor Duty TP Contactor, &

set of ON/OFF indication Lamps and set of Push Buttons (PBs) for manual

operation & 1 no. Auto/Manual (A/M) selector switch and (10 steps) APFC relay of

required capacity for powerfactor correction panel, checking its main operating

parameters such as overloads and short circuits.

Provisions should be there to enhance the capacity of the panel by adding additional

racks of as mentioned above and to be added vertically upwards so as to avoid

occupying extra space horizontally. The other general specifications shall be as

Note : The capacitors shall be of type LL-10 Mono long life capacitors

General Specifications :

Rated voltage : 400 to 440V A.C, 3 Phase

Rated frequency : 50 Hz

Permissible over voltage : 1.1 Vn

Permissible over current : 1.3 ln

Temperature range : 50oC

Dielectric loss : Below 0.2 W/KVAR

Capacitors : IS 2834/1986, IEC : 831/1&2

PF Correction panel : IEC 439/ 1-2

APFCR of 10 steps

CAPACITOR PANEL

INCOMERS : 400kVAR CAPACITOR PANELS

1 No. 800A TP Isolator

1 Set of phase indicating lights LED type with control of 2A SP MCB

1 No. Auto manual selecter switch

1 No. Digital VIF meter with class-1 800/5A, CT's

Capacitor banks

10kVARx2= 20kVAR

Each 10kVAR bank to have 25A TP capacitor duty contactor , OLR and 25A TP

25kA MCCB, on-off indicator, on-off push buttons for manual operation

15kVARx2= 30kVAR

Each 15kVAR bank to have 40A TP capacitor duty contactor , OLR and 32A TP

25kA MCCB, on-off indicator, on-off push buttons for manual operation

25kVARx2= 50kVAR

Each 20kVAR bank to have 63A TP capacitor duty contactor , OLR and 63A TP

25kA MCCB, on-off indicator, on-off push buttons for manual operation

50kVARx2=100kVAR

Each 50kVAR bank to have 125A TP capacitor duty contactor, OLR and 125A TP

25kA MCCB, on-off indicator, on-off push buttons for manual operation

100kVARx2=200kVAR

Each 50kVAR bank to have 250A TP capacitor duty contactor, OLR and 250A TP

25kA MCCB, on-off indicator, on-off push buttons for manual operation

Total kVAR capacity : 400kVAR

CAPACITOR PANELS AS DESCRIBED ABOVE Each 1.00 500000.00 0.00 500000.00

145 A/R on MR COMMON AREA SERVICES (C.A.S. PANEL-I)

1 No. 160A, 415V, Ics=Icu=35kA rupturing capacity, FP, MCCB with phase spreader

& extended rotary handle

1 Set of phase indicating lights LED type with control of 2A SP MCB

1 No. VIF meter (VIF) with CT's 160/5A & control of 2A SP MCB

1 No. kilo watt hour meter (kWHr) with control of 2A SP MCB

200A TPN busbars of aluminium with colour coded heat shrinkable sleeves and with

SMC/DMC supports at every 600mm intervals and at both ends

6 Nos. 100A, 415V, Ics=Icu=25kA rupturing capacity, TPN, MCCB with phase

spreader & extended rotary handle

COMMON AREA SERVICES (C.A.S PANEL-I) AS DESCRIBED ABOVE Each 1.00 95000.00 0.00 95000.00

146 A/R on MR MDB CA TYPICAL FOR HIGH RISE TOWER (Type-IV, V VI)

1 No. 100A, 415V, Ics=Icu=25kA rupturing capacity, FP, MCCB with phase spreader

& extended rotary handle

1 Set of phase indicating lights LED type with control of 2A SP MCB

1 No. VIF meter (VIF) with CT's 100/5A & control of 2A SP MCB

1 No. kilo watt hour meter (kWHr) with control of 2A SP MCB

200A phase and neutral TPN busbars of aluminium with colour coded heat

shrinkable sleeves and with SMC/DMC supports at every 600mm intervals and at

2Nos. 100A, 415V, Ics=Icu=25kA rupturing capacity, TPN, MCCB with phase

spreader & extended rotary handle

3 Nos. 20A 10kA DP MCB

2 Nos. 63A 10kA FP MCB

MDB CA FOR HIGH RISE TOWER AS DESCRIBED ABOVE Each 4.00 42000.00 0.00 168000.00

COMMON AREA LIGHTING PANEL-TOWER 1 AND TYPICAL FOR TOWER 2, 3 &

1 No. 63A, 415V, 10kA FP MCB

1 Set of phase indicating lights LED type with control of 2A SP MCB

I No. Digital Multifunction Astronomical time switch

1 No. 63A FP power contactor with ON-OFF push buttons including indicating LED

Lamps (R & G) for manual over riding of the timer and a set of contacts for remote

ON-OFF operation

200A phase and neutral TPN busbars of aluminium with colour coded heat

shrinkable sleeves and with SMC/DMC supports at every 600mm intervals and at

3 Nos. 40 A 10kA FP MCB

TOWER COMMON AREA LIGHTING PANEL AS DESCRIBED ABOVE Each 4.00 15000.00 0.00 60000.00

148 A/R on MR LIFT PANEL -TOWER 1 AND TYPICAL FOR TOWER 2, 3 & 4

1 No. 160 A FP manual change-over switch for two supplies- one from rising main

and other from MDB-CA Panel for lift Panels of high rise tower

1 No. 100A, 415V, Ics=Icu=25kA rupturing capacity, FP, MCCB with phase spreader

& extended rotary handle

1 Set of phase indicating lights LED type with control of 2A SP MCB

1 No. VIF meter (VIF) with CT's 100/5A & control of 2A SP MCB

200A phase and neutral TPN busbars of aluminium with colour coded heat

shrinkable sleeves and with SMC/DMC supports at every 600mm intervals and at

3 Nos. 63A, 415V, Ics=Icu=25kA rupturing capacity, TPN, MCCB with phase

spreader & extended rotary handle

2 Nos. 32A 10kA DP MCB

LIFT PANEL FOR TOWERS A,B AS DESCRIBED ABOVE Each 4.00 55000.00 0.00 220000.00

149 A/R on MR BASEMENT LIGHTING PANEL

1 No. 100A, 415V, Ics=Icu=25kA rupturing capacity, FP, MCCB with phase spreader

& extended rotary handle

1 Set of phase indicating lights LED type with control of 2A SP MCB

1 No. VIF meter (VIF) with CT's 100/5A & control of 2A SP MCB

1 No. kilo watt hour meter (kWHr) with control of 2A SP MCB

200A phase and neutral TPN busbars of aluminium with colour coded heat

shrinkable sleeves and with SMC/DMC supports at every 600mm intervals and at

4 Nos. 32 A 10kA DP MCB

3 Nos. 32 A 10kA FP MCB

6 Nos. 40 A 10kA FP MCB

BASEMENT LIGHTING PANEL AS DESCRIBED ABOVE Each 1.00 48000.00 0.00 48000.00

150 A/R on MR METER BOARDS

i) The energy meters shall be dual register type, 3 phase, 4 wire 415V, 50Hz with

built in CTs suitable for prepaid metering & with current limiting facility

ii) The meters shall be compatible with centrally controlled billing system with RS-

iii) Meter boards shall be suitable for mounting directly on the rising main.

151 A/R on MR METER BOARDS TYPE -A

1 No. 100A, 415V, Ics=Icu=25kA rupturing capacity, FP, MCCB with phase spreader

& extended rotary handle

1 Set of phase indicating lights LED type with control of 2A SP MCB

200A Phase and Neutral TPN busbars of aluminium with colour coded heat

shrinkable sleeves and with SMC/DMC supports at every 600mm intervals and at

Meter compartments

3 Nos. Meter Compartments of suitable size with three phase 4 wire dual direct type

The vendor shall submit details before fabrication

152 A/R on MR METER BOARDS TYPE B

1 No. 63A, 415V, Ics=Icu=25kA rupturing capacity, FP, MCCB with phase spreader

& extended rotary handle

1 Set of phase indicating lights LED type with control of 2A SP MCB

200A Phase and Neutral TPN busbars of aluminium with colour coded heat

shrinkable sleeves and with SMC/DMC supports at every 600mm intervals and at

Meter compartments

2 Nos. Meter Compartments of suitable size with three phase 4 wire dual direct type

The vendor shall submit details before fabrication

153 A/R on MR METER BOARDS TYPE C

1 No. 100A, 415V, Ics=Icu=25kA rupturing capacity, FP, MCCB with phase spreader

& extended rotary handle

1 Set of phase indicating lights LED type with control of 2A SP MCB

200A Phase and Neutral TPN busbars of aluminium with colour coded heat

shrinkable sleeves and with SMC/DMC supports at every 600mm intervals and at

Meter compartments

2 Nos. Meter Compartments of suitable size with three phase 4 wire dual direct type

The vendor shall submit details before fabrication

154 A/R on MR Feeder Pillars

Supply, installation, testing and commissioning of following type of feeder pillars

suitable for 415V, 3 Phase, 4 wire, 50Hz supply system having degree of protection

IP-55 as per IS-2147 made out of 2mm thick CRCA sheet steel, powder coated,

dust, damp and vermin proof, partially compartmentalized , rear opening for cable

terminations & front opening for switchgears, heavy duty moulded terminal blocks

for incoming/outgoing and wiring with copper conductor 1100V grade flexible cable,

locking arrangements, earth bus, PCC foundation etc. complete as required with

following mountings : -

155 A/R on MR INCOMER (For External Lighting)

1 No. 63A, 415V, Ics=Icu=25KA rupturing capacity,FP, MCCB

A set of phase indicating lights with control of 2A SP MCB.

I No. Digital Multifunction Astronomical time switch

1 No. 63A FP power contactor with ON-OFF push buttons including indicating LED

Lamps (R & G) for manual over riding of the timer and a set of contacts for remote

ON-OFF operation

One set of 200A TPN Aluminium busbars with colored PVC sleeves and SMC/DMC

busbar supports at both ends and maximum 600mm apart

Programmable electronic timer for auto switching of the external lighting switching

ON - OFF of the contractor as per the preset astranomical time settings depending

upon the seasonal requirements

40A 10KA DP MCB -3 Nos.

156 A/R on MR CLUB PANEL

1 No. 100A, 415V, Ics=Icu=35kA rupturing capacity, FP, MCCB with phase spreader

& extended rotary handle

1 Set of phase indicating lights LED type with control of 2A SP MCB

1 No. VIF meter (VIF) with CT's 100/5A & control of 2A SP MCB

1 No. kilo watt hour meter (kWHr) with control of 2A SP MCB

200A phase and neutral TPN busbars of aluminium with colour coded heat

shrinkable sleeves and with SMC/DMC supports at every 600mm intervals and at

2 Nos. 63A, 415V, Ics=Icu=25kA rupturing capacity, TPN, MCCB with phase

spreader & extended rotary handle

2 Nos. 32A 10kA DP MCB

5 Nos. 40A 10kA FP MCB

CLUB PANEL AS DESCRIBED ABOVE Each 2.00 50000.00 0.00 100000.00

157 A/R on MR MULTI PURPOSE HALL PANEL

1 No. 63A, 415V, Ics=Icu=35kA rupturing capacity, FP, MCCB with phase spreader

& extended rotary handle

1 Set of phase indicating lights LED type with control of 2A SP MCB

1 No. VIF meter (VIF) with CT's 63/5A & control of 2A SP MCB

1 No. kilo watt hour meter (kWHr) with control of 2A SP MCB

200A phase and neutral TPN busbars of aluminium with colour coded heat

shrinkable sleeves and with SMC/DMC supports at every 600mm intervals and at

1 No. 63A, 415V, Ics=Icu=25kA rupturing capacity, TPN, MCCB with phase spreader

& extended rotary handle

2 Nos. 32A 10kA DP MCB

3 Nos. 40A 10kA FP MCB

MULTI PURPOSE HALL PANEL AS DESCRIBED ABOVE Each 1.00 27000.00 0.00 27000.00

Total: Subhead 2 1532434.00 4985040.00

Subhead 3: Earthing

Earthing with G.I. earth pipe 4.5 meter long, 40mm dia including accessories, and

158 5.2 providing masonry enclosure with cover plate having locking arrangement and Each 18.00 5308.00 95544.00 0.00

watering pipe etc. with charcoal/coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories,

and providing masonry enclosure with cover plate having locking arrangement and

watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including

accessories, and providing masonry enclosure with cover plate having locking

arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as

required. (for lift)

Providing and fixing 50 mm x 6 mm GI strip on surface or in recess for connections

161 A/R on MR etc. as required. HT panel, LT Panels, transformers and DG Sets body earthing. M 910.00 350.00 0.00 318500.00

Providing and fixing 40 mm x 6 mm Cu strip on surface or in recess for connections

etc. as required. For Trafo and DG set neutrals earthing.

Providing and fixing 32 mm x 6 mm GI strip with heat shrinking sleeves & SMC/DMC

163 A/R on MR insulators on surface for cable tray and connections for rising mains etc. as required. M 400.00 285.00 0.00 114000.00

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as

strip earth electrode, including connection/terminating with nut, bolt, spring, washer

etc. as required.(Jointing shall be done by overlapping and with 2 sets of brass nut

bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I. strip at 0.50 meter below ground as strip

earth electrode including connection/ terminating with G.I. with nut, bolt, spring,

washer etc as required. ( Jointing shall be done by overlapping and with 2 sets of nut

bolt & spring washer spaced at 50mm )

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth

166 5.1 electrode including connection with brass nut, bolt, spring, washer excavation and re- Each 80.00 1224.00 97920.00 0.00

filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth

167 5.11 electrode including connection with brass nut, bolt, spring, washer excavation and re- M 50.00 483.00 24150.00 0.00

filling etc. as required.

Providing and fixing 25 mm x 5 mm Copper strip on surface or in recess for

connection etc. as required.

Providing and fixing 25 mm x 5 mm G.I. strip on surface or in recess for connection

etc. as required.

Total: Subhead 3 2314478.00 1191500.00

Subhead 4: Cable, Cable Tray and Miscellaneous Items

Supplying and installing Following size of perforated pre-painted M.S. cable trays

with perforation not more than 17.5% in convenient sections, joined with connectors,

suspended from the ceiling with M.S. suspenders including bolts & nuts, painting

suspenders etc as required.

a 4.1.2 150mm widthx50mm depthx1.6mm thickness M 300.00 531.00 159300.00 0.00

b 4.1.4 300mm widthx50mm depthx1.6mm thickness M 350.00 621.00 217350.00 0.00

c 4.1.6 450 mm width X 50 mm depth X 2.0 mm thickness M 100.00 700.00 70000.00 0.00

d 4.1.14 600 mm width X 75 mm depth X 2.0 mm thickness M 50.00 1000.00 50000.00 0.00

e 4.1.16 900 mm width X 75 mm depth X 2.0 mm thickness M 150.00 1184.00 177600.00 0.00

Supplying and installing Following size of perforated pre-painted M.S. cable trays

bends with perforation not more than 17.5% joined with connectors, suspended from

171 4.2 the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as

required. Note: As per Site Requirement

a 4.2.2 150mm widthx50mm depthx1.6mm thickness Each 5.00 947.00 4735.00 0.00

b 4.2.4 300mm widthx50mm depthx1.6mm thickness Each 5.00 1340.00 6700.00 0.00

c 4.2.6 450 mm width X 50 mm depth X 2.0 mm thickness Each 2.00 2089.00 4178.00 0.00

d 4.2.14 600 mm width X 75 mm depth X 2.0 mm thickness Each 2.00 2830.00 5660.00 0.00

e 4.2.16 900 mm width X 75 mm depth X 2.0 mm thickness Each 2.00 3927.00 7854.00 0.00

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power

172 7.5 cable of 1.1 KV grade of following size in the existing RCC/HUME/Metal pipe as

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power

173 7.6 cable of 1.1 KV grade of following size in the existing masonry open duct as

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power

cable of 1.1 KV grade of following size on cable tray as required.

a 7.8.1 Upto 35 sq. mm (clamped with 1 mm thick saddle) M 1375.00 33.00 45375.00 0.00

b 7.8.2 Above 35 sq.mm. and upto 95 sq.mm (clamped with 25x3 mm MS flat clamp) M 698.50 74.00 51689.00 0.00

Above 95 sq. mm and upto 185 sq. mm (clamped with

25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with

40x3mm MS flat clamp)

Supplying and making indoor end termination with brass compression gland and

175 9.1 aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 KV grade as required.

Supplying following size of PVC insulated and PVC sheathed / XLPE

aluminium/Copper armoured conductor cable of 1.1 KV grade as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all

accessories like socket, bend, couplers etc.conforming to IS 14930, Part II complete

with fitting and cutting, jointing etc.direct in ground (75 cm below ground level)

including excavation and refilling the trench but excluding sand cushioning

and protective covering etc., complete as required.

Constructing masonry Chamber 45x45x45 cm inside, in brick work in cement mortar

1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top

diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and

RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm

178 A/R on MR nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5

fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering

with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a

floating coat of neat cement complete as per standard design :

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar

1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top

diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and

RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm

179 18.33 nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5

fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering

with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a

floating coat of neat cement complete as per standard design :

18.33.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 No. 6.00 9288.40 55730.40 0.00

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement

mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm

top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid

and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate

180 18.34 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1

cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside

plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished

with a floating coat of neat cement complete as per standard design :

18.34.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 No. 3.00 16134.15 48402.45 0.00

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11

181 8.1 KV grade of following size direct in ground including excavation, sand cushioning,

protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11

182 8.3 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

supplying and making indoor cable end termination with heat shrinkable jointing kit

183 10.4 complete with all accessories including lugs suitable for following size of 3 core,

XLPE aluminium conductor cable of 11 KV grade as required.

Supplying of following sizes of 11 kV grade aluminium conductor XLPE armoured

cable conforming to IS : 7098 (part-2)

Total: Subhead 4 1590983.25 2453967.00

Subhead 5: Internal Light fixtures and Fans

Supply of prewired LED light fixtures complete with lamp, ballast, driver, transformer

185 A/R on MR and all other accessories etc. complete factory wired with copper conductor but as

a)1x20 W LED tubelight Polycarbonate co-extrusion tube for LED light housing with

engg.plastic end caps Surface Mounted

Make/Cat Ref. : Bajaj / BCLSB 20W Each 1742.00 750.00 0.00 1306500.00

b)Decorative Wall light -Embrace White LED

c)Mirror Light (Bathroom Wall light) 7.5W Jojoba Silver, LED

d)1x5 W LED tubelight Polycarbonate co-extrusion tube for LED light housing with

engg.plastic end caps Surface Mounted

Make/Cat Ref. : Bajaj / BCLSB 5W Each 366.00 600.00 0.00 219600.00

e)10W Bulk Head

Make/ Type : Bajaj/BIBWP 10W LED Each 12.00 1200.00 0.00 14400.00

f)1x6 W LED Surface Mounted Downlighter die-cast aluminum frame

Make/ Type : Bajaj/BGSLO Sleek Surface 6W WH RD Each 1434.00 1400.00 0.00 2007600.00

g)1x6 W LED Recessed Downlighter die-cast aluminum frame

Make/ Type : Bajaj/BPSLR Radiance 6W WW RD Each 250.00 1000.00 0.00 250000.00

Supply of following duty and sizes of Exhaust Fans complete with motor, capacitor,

terminal block, shuttered louvers etc. complete as required.

230mm sweep 1350 r.p.m with Guard Each 553.00 1200.00 0.00 663600.00

Supply of following sizes of ceiling fans complete with fan motor, capacitor of

required rating, terminal block, standard down rod, wiring of down rod, fixing hooks

with nuts & bolts, rubber bush, shrouding caps etc. complete as required.

a)1200 mm dia sweep

Make/Type: Luminous Pulse 50 5 Star

Supplying, installing, testing and commissioning of LED based Aviation Obstruction

188 A/R on MR Light of an approved make with photo cell. (Cost of wiring to be paid seperately). Each 8.00 6000.00 0.00 48000.00

Total: Subhead 5 0.00 7968600.00

Subhead 6: Rising Mains

Supplying, installing on wall, testing and commissioning of following capacity Air

Insulated Compact Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz

A.C. supply with enclosure having IP-54 rating after fixing the tap off boxes and all

accessories, made of 1.6mm thick steel sheet duly powder coated in convenient

sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq

cm at nominal current rating, necessary joints & expansion joints, fire barrier at each

floor, provision of tapping at every metre, continuous earthing with 2 Nos aluminium

strip of suitable size (one on each side) including, G.I. clamping brackets, angle iron

bracket, steel fasteners, connecting to earthing system etc. as required.

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off

box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on

190 3.12 3 phase 4wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel

enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without

MCCB/ACB) complete etc. as required

Supplying, installation, testing & commisioning of following capacity End Feed Unit

for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3

phase 4 wire 415volts, 50Hz A.C. supply made with 1.6mm thick steel sheet

191 3.11 enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without

MCCB/ACB) complete with necessary joints including clamping brackets, angle iron

bracket, steel fasteners, connecting to earthing system etc. as required

Providing and fixing following rating and breaking capacity and pole MCCB with

thermomagnetic release and terminal spreaders in existing cubicle panel board

including drilling holes in cubicle panel, making connections, etc. as required.

Total: Subhead 24 1969312.00 0.00

Subhead 7: Fire Alarm System

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated

with annealed copper conductor having glass mica fire barrier tape covered by an

193 17.5.1 extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and M 1045.00 328.00 342760.00 0.00

LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as

Supplying, installation, testing & commissioning of manual call boxes of MS

194 17.1.3 construction in surface/recess with stainless steel chain & hammer assembly Each 54.00 462.00 24948.00 0.00

complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to

make announcement, mounted in M.S. box (16 SWG) with hinged cover plate &

suitable for operation with amplifier i/c line matching transformer etc. complete as

Supplying, installation, testing & commissioning of smoke detector with builtin LED

and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning response indicator on

197 17.1.5 surface/recess MS box having two LEDs metallic cover complete with all Each 53.00 184.00 9752.00 0.00

connections etc. as required.

Supplying, installation, testing & commissioning talk back slave station in

surface/recess suitable for operation on simplex mode complete with P.T.T. knob &

speaker/microphone enclosed in a M.S.(16 SWG)/ ABS box with break glass in front

etc. complete as required.

Supplying, installation, testing & commissioning of main

control and indicating panel made out of 16 SWG MS sheet to accommodate the

following items duly powder coated in approved colour with louvers for ventilation,

locking arrangement, audio and visual indication for fire alarm and public address

system, monitoring system including connections, interconnections etc complete as

10 Zone panel for fire alarm system

250 Watt amplifier racks suitable for operation on 230V

AC/24V DC supply conforming to IEC-268-3 complete with all accessories as

required - 2 Nos.(one to act as standby) Talk back master station with LED PTT

(press to talk) push button for operation on 230V AC/24 V DC supply conforming to

IEC-268 for simplex mode of operation/communication suitable for 20 Nos.talk back

Annoucement control desk suitable for selection of differentzones selectively and ON

199 17.1.10 ALL CALL switch with visual indication etc. complete as required -1 set. Each 8.00 69084.00 552672.00 0.00

Amplifier change over switch for inter changing amplifier -1 No.

Monitor panel for loudspeaker complete with output selector, ON/OFF switch, fuse,

visual indications etc.

complete as required- 1 No.

Gooseneck microphone with stand and ON/OFF switch- 1 No.

Main ON/OFF switch, fuse indication lamps, DC and AC

voltmeters & ammeters, terminal blocks etc. complete as

required -1 set.

Battery charger trickle cum boost to take complete load of fire alarm & PA system

complete with all accessories

including providing & fixing of 2 nos.12 volt, 60 AH each

sealed maintenance free batteries -1 set.

Supplying, installation, testing & commissioning of central graphical fire alarm

200 17.2.2 management system to centrally monitor and operate the fire alarm system complete Each 1.00 200148.00 200148.00 0.00

Supplying, installation, testing & commissioning of addressable fire control module

complete as required.

Supply, installation, testing and commissioning of Addressable Zoning Monitor

Supply, installation, testing and commissioning of Addressable Monitor Modules for

203 A/R interfacing conventional Tower Fire alarm panel, Sprinkler flow switches with central Each 9.00 3200.00 0.00 28800.00

addressable Fire Alarm panel.

Supplying, installation, testing & commissioning of repeater panel wih 320 character/

204 17.2.3 Touch screen LCD display with inbuilt reset, acknowledge and silence switches Each 1.00 108572.00 108572.00 0.00

complete as required.

Supplying and fixing of following sizes of steel conduit along with accessories in

205 1.2 surface/recess including painting in case of surface conduit, or cutting the wall and

making good the same in case of recessed conduit as required.

Supplying, laying and connecting of following size 1.1 kV grade copper conductor

control cable (conforming to IS:1554 Part I) on wall or on existing cable tray/ in

existing pipe/trench with clamping, dressing or drawn in existing ducts all as

2X 1.5 sq.mm.unarmoured cable M 2612.50 90.00 0.00 235125.00

Total: Subhead 7 1575838.00 279925.00

Subhead 8: Lightning Protection System

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long,

207 6.2 G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate Each 24.00 448.00 10752.00 0.00

including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any

208 6.4 other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. Each 120.00 93.00 11160.00 0.00

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for

lightning conductor complete as required. (For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for

lightning conductor complete as required. (For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm

211 6.12 long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as Each 24.00 102.00 2448.00 0.00

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground

Total: Subhead 8 361000.00 0.00

Subhead 9: HT Panel

213 A/R on MR H.T. PANEL NEAR METER ROOM

Supply, installation, testing and commissioning of 1 No. Panel 11 KV switchboard

fitted with VACCUM CIRCUIT BREAKERS with accessories as below and as per

detailed specifications.

INCOMER CUM OUTGOING END TERMINATION

1 No. fully drawout VCB CB TP 630A and 18.4 KA breaking capacity OF 350 MVA

with closing and tripping circuit suitable for 24V DC and motorised spring charged

complete with auxiliary contacts ON/OFF indicator, spring charged/dischage

indicator, operation counter, operating handle, fully interlocked, for service, test and

isolated positions.

1 Set of dual core current transformers of ratios 300/150/5A with metering core of

class 1-0 and burden of 15 VA and protection core 5 P 1 0, burden 15 VA.

1 Set of PTs 11KV /1.734/110V/1.734 100VA burden with set of HRC fuses on H.T.

1 Set of IDMT relay for over current and earth fault with high set element

1 Set of Ammeter with Selector switch

1 Set of Voltmeter with Selector switch

1 Set indicating lamps for ON-OFF and FAULT

1 Set of indicating lamps for Trip healthy, Trip failure circuit with audible alarm.

Circuit breaker control switch.

1 Sets of panel space heaters with control switch, thermostat and fuses.

Earth bar for all panels and sliding earth contact for movable truck portions of

Testing terminal block for panels.

Panel interior illuminating lamp with door switch for all panels.

Designation labels on front and rear.

A builtin power pack unit containing AC to DC convertor with battery charger and

battery of capacity 7AH suitable for the DC load of the single breaker VCB panel

board with DC Voltmeter, Ammeter, charge selector switch, indicating lamps and

control fuses etc. ae required.

214 A/R on MR H.T. PANEL NEAR ESS

Supply of 3 Panel 11 KV switchboard with 1 incoming panel and 2 outgoing Panels

fitted with VACCUM CIRCUIT BREAKERS with accessories as below and as per

detailed specifications.

INCOMER VCB PANEL

1 No. fully drawout VCB Panel TP 630A and 18.4 kA breaking capacity of 350 MVA

with closing and tripping circuit suitable for 24V DC power and motorised spring

charged complete with auxiliary contacts ON/OFF indicator, spring charged

/dischage indicator, three position isolaotr/ earthing switch, busbar, earthbar

operation counter, operating handle, integral spring charging handle, fully

interlocked, for service, test and isolated positions with making capacity.

1 Set of dual core cast resin current transformers of ratios 11 kV, 300/150/5A with

metering core of class 1-0 and burden of 15 VA and protection core 5 P 1 0, burden

1 Set of withdrawable cast resin PTs 11KV /1.734/110V/1.734, 100VA burden of

class-1 with set of HRC fuses on H.T. and L.T. side.

METERING COMPARTMENT

Numerical relay with LCD display- IDMT relay for 2 Nos.Over Current and 1 No.Earth

Fault with high set element

Inbuilt master trip relay (86) and trip circuit supervision function

1 No. Multifunction meter with RS-485 port

1 set of Phase indicating lamps LED type with control MCB

1 Set indicating lamps for breaker ON-OFF and Trip (RGA)

Spring Charged lamp (Blue)

DC Supply healthy indicating lamp

DC failure relay with buzzer and indication with accept push button

1 Set of indicating lamps for Trip circuit healthy, Trip circuit failure with audible

Anti pumping Realy

Local remote selector switch

Circuit breaker control switch. (T-N-C)

Emergency stop push button (Red)

1 Set of panel space heaters with control switch, thermostat and fuses.

Earth bar for all panels and sliding earth contact for movable truck portions of

Panel interior illuminating lamp with door switch for all panels.

Racking in/out, Manual closing/tripping of the circuit breaker with compartment door

Continuous rated closing/tripping coils

Testing terminal block for panels.

Auxiliary Switch with 6 NO + 6NC contacts mounted on the drawout portion of

Position/cell switch with 3 NO + 1 NC contacts, one each for TEST and SERVICE

Auxiliary switch, with 4 NO+4NC contacts, mounted on the stationary portion of the

operated mechanically by a sliding lever from the breaker in service position.

2 NOS. OUTGOING VCB PANEL

Each Breakers consisting as below

1 No. fully drawout VCB Panel TP 630A and 18.4 kA breaking capacity of 350 MVA

with closing and tripping circuit suitable for 24V DC power and motorised spring

charged complete with auxiliary contacts ON/OFF indicator, spring charged

/dischage indicator, three position isolaotr/ earthing switch, busbar, earthbar

operation counter, operating handle, integral spring charging handle, fully

interlocked, for service, test and isolated positions with making capacity.

1 Set of dual core cast resin current transformers of ratios 11 kV, 150/75/5A with

metering core of class 1-0 and burden of 15 VA and protection core 5 P 1 0, burden

METERING COMPARTMENT

Numerical relay with LCD display- IDMT relay for 2 Nos.Over Current and 1 No.Earth

Fault with high set element

Inbuilt master trip relay (86) and trip circuit supervision function

1 No. Multifunction meter with RS-485 port

1 set of Phase indicating lamps LED type with control MCB

1 Set indicating lamps for breaker ON-OFF and Trip (RGA)

Spring Charged lamp (Blue)

DC Supply healthy indicating lamp

DC failure relay with buzzer and indication with accept push button

1 Set of indicating lamps for Trip circuit healthy, Trip circuit failure with audible

Anti pumping Realy

Local remote selector switch

Circuit breaker control switch. (T-N-C)

Emergency stop push button (Red)

1 Set of panel space heaters with control switch, thermostat and fuses.

Earth bar for all panels and sliding earth contact for movable truck portions of

Panel interior illuminating lamp with door switch for all panels.

Racking in/out, Manual closing/tripping of the circuit breaker with compartment door

Continuous rated closing/tripping coils

Testing terminal block for panels.

6 Nos. auxiliary relay for Oil teperature indicator(OTI), Winding temperature indicator

(WTI), Bucholz alarm & trip.

Annunciator with electronic hooter

Auxiliary Switch with 6 NO + 6NC contacts mounted on the drawout portion of

Position/cell switch with 3 NO + 1 NC contacts, one each for TEST and SERVICE

Auxiliary switch, with 4 NO+4NC contacts, mounted on the stationary portion of the

operated mechanically by a sliding lever from the breaker in service position.

Designation labels on front and rear.

Supplying and fixing of tripping battery 24V supply with a Self Contained floor

mounting cabinet complete with required number of lead acid maintenance free

storage batteries of capacity of 125 AH each suitable for the DC load of the 3 panel Each 1.00 950000.00 0.00 950000.00

board and with a float cum boost charger with DC Voltmeter, Ammeter, charge

selector switch, indicating lamps and control fuses.

Total: Subhead 9 0.00 1300000.00

Subhead 10: Distribution Transformers

215 A/R on MR 1250kVA DRY TYPE INDOOR TRANSFORMER

Supply, installation, testing and commissioning of 11KV/.433KV, 1250 KVA dry type

transformer conforming to IS: 11171, suitable for indoor installation, including

mounting channels, making cable connections on H.T. and cable box L.T. side

suitable for 6 nos. 3.5C 400sq. mm aluminium conductor armoured cables, complete

with all accessories as per detailed specification.

a) 1250KVA dry type transformer

b) Off circuit tap changer with +5% to -5% in steps of 2.5% on HT side. Each 1.00 1500000.00 0.00 1500000.00

Total: Subhead 10 0.00 1500000.00

Subhead 11: D.G. Sets

Supply of Sound Attenuated Weather Proof type of D.G. Set of required rating

complete with diesel engine and alternator of suitable rating, micro processor based

216 A/R on MR control panel for metering, monitoring, protection and electronic governing of the

engine and all other accessories as per detailed specifications and as specically

mentioned below :

Sound Attenuated Weather Proof Canopy : Shall be engineered to meet all the

Engine : Radiator Cooled, Fuel Efficient and meeting emission norms

Alternator : Efficient, Brushless, self-excited, with electronic AVR, rated for 0.8 pf 415

Volt, 3 Phase 4 Wire, 50 Hz supply; coupled to engine

Control Panel : Microprocessor based compatible having DG Set performance

parameetrs display panel, diagnostics and engine and alternator protection features,

remote monitoring & data logging, compatibility panels,etc.

Providing the HSD and other comsumables for the successful comissioning of the

Accessories : Base frame with maintenance free vibration control system, fuel

storage tank in the base, required nos. of batteries with battery charger and stand,

and other accessories as per detailed specifications and as requred for the

successful operation of the DG set.

Installation, testing and commisioning of DG Sets of following capacities including

217 A/R on MR hoisting, placing on plinths, supply of HSD and other consumables required for

successful commissioning, all complete.

Note : All civil and structural steel work for plinth construction will be done by a third

party as per the detailed design and drawings provided by the DG Set Vendor.

a) 320 kVA DG Set to be installed as required Each 2.00 60000.00 0.00 120000.00

Supply, jointing by welding, installation and commissioning of DG Exhaust Pipe

System fabricated out of heavy quality (Class C) M.S. pipes conforming to IS:1239

(Part I) - 1990 for pipes upto 150 mm dia. and IS:3589-1991 for pipes above 150mm

dia. including fittings i.e. tees, bends, elbows, unions, reducers, draining

arrangement, flange joints, rubber insertion, nuts & bolts etc. as required including

fixing of exhaust system on existing walls, slabs, steel structure etc. with flat iron

strap work, including painting with two coats of anti-corrosive paint. The exhaust

system shall be insulated with 75 mm thick ROCK wool insulation of 150 Kg per

cubic meter density on around of Exhaust pipe and silencer, firmly kept in place with

chicken wire mesh wrapping and followed by cladding with aluminium sheet of 24

SWG, complete as required and as per specification.

The Sizes of the exhaust piping are indicative only and the DG set supplier should

furnish the Calculations for exhaust piping sizes for approval by the

architect/consultant/Client

The System should meet the performance of the engine without exceeding the back

pressure limit prescribed by the engine manufacturer.

In case the selected size as per calculation of back pressure is not the same as

specified below than the size and the rate of the size so selected shall also be

a) Supply and fixing of 125 mm dia MS Black Pipe 4.85mm thick complete with

a A/R on MR Bends & Flanges. With Rockwool 75mm Thick wire mesh and 24 gauge aluminium M 10.00 1000.00 0.00 10000.00

b) Supply and fixing of 150 mm dia MS Black Pipe 4.85mm thick complete with

b A/R on MR Bends & Flanges. With Rockwool 75mm Thick wire mesh and 24 gauge aluminium M 150.00 1300.00 0.00 195000.00

c A/R on MR c) Supply of MS Support for exhaust piping kg 500.00 100.00 0.00 50000.00

d A/R on MR d) Supply of Flexible SS Belows (as per site condition) Each 4.00 12000.00 0.00 48000.00

Total: Subhead 11 0.00 6423000.00

Subhead 12: Lifts

Supply, Installation, Testing and Commissioning of MRL Lifts including 1 year's

Guarantee & Free Maintenance

Design, manufacturing, testing at works, supply and delivery, receiving, unloading,

storing, inspection, handling, assembling, installing in correct assigned position,

effecting proper connections, testing and commissioning of following capacity MRL

passenger-lifts, having speed of 1.5 MPS 12 stops and 12 openings and total travel

of 37.0 Meters approx. with VVVF drive, full collective Simplex/duplex control on

415V, 50 cycles, 3 phase power complete in accordance with specifications and

drawings as required with Car, Car Door & Hoistway Door in stainless steel hairline

finish, inclusive of builtin ARD and as per specification. Note :- Refer Sections 1.1 &

1.2 of Technical Specification for genral requirements of MRL Lifts.

(i) 13 Passenger (1020Kg) For Highrise Towers (Refer Sections 1.1) No. 4.00 2200000.00 0.00 8800000.00

(ii) 8 Passenger (544Kg) For Highrise Towers (Refer Sections 1.2) No. 4.00 2000000.00 0.00 8000000.00

Total: Subhead 12 0.00 16800000.00

Subhead 13: Street Light Poles & Light Fixtures

Supply and errection of flange mounted hot dip galvanized conical pole of specified

length made from 3mm thick MS sheet, complete with window with sliding flush

cover at a height of 0.5 M from the base for cable termination block etc and

galvanized base plate of size 25mm x 225mm x 16mm / as required. The pole top

shall be complete with 1000 mm long arm bracket at specified height with a tilt of 0

degree with tightening bolts as required. The following may be housed in the window

provided for cable termination including their supply and fixing:: 6mm thick

laminated mounting sheet of suitable size inside the window by providing and

welding three No GI strips; 4 mm thick of suitable length and having suitable size

220 A/R on MR tapped holes - 10 nos. as required. : 1 No. : A set of 20 Amp brass neutral link, 2

way copper bus bar on existing laminated sheet : 1 Set.: 4 way, 32 Amp heavy duty

terminal block suitable for 10 sq. mm conductor- 2nos. and shorting links (4nos.) on

DIN channel of suitable length - on the existing laminated sheet. : Earth stud

welded at suitable height with two nos. washer, spring washer & nuts. : 2 Nos.: 4

Nos. (20mm dia x 470mm long) G.I foundation bolts with nuts washer, 2 nos.

templates (4 mm thick, 220mm x 22 0mm size), making of 4 Nos. x 24 mm dia holes

with PCD of 205mm for 6 M Poles . The tem-plate (Top) shall have a 120 mm dia

hole at center for cable entry

b) 6M long Conical pole- BCP-6030- ( Top Dia: 75mm, Bottom dia: 140 mm, pole

thickness:3mm) with 0.5M single arm bracket along

c)3) 6M long Conical pole- BCP-6030- ( Top Dia: 75mm, Bottom dia: 140 mm, pole

thickness:3mm) with 0.5M double arm bracket

d) 4M long Conical pole- BCP-4030- ( Top Dia: 75mm, Bottom dia: 118 mm, pole

thickness:3mm) with 0.2M single arm bracket

Supply of following type of prewired street light luminaires complete with lamps,

221 A/R on MR ballast, transformers, drivers as required of following makes and models (or

approved equivalent)

a) Make : Bajaj

Model No. : ARAIN-BCGT W4 LED WW

Housing: Die-cast aluminum graphite grey powder coated

Mounting Height: 4M

Color Temp: Warm White : 3000k - White Each 25.00 30000.00 0.00 750000.00

b) Make : Bajaj

Model No. : EDGE-BRTFG 45W LED WW

Housing: Pressure Die-cast aluminum with toughend glass

Mounting Height: 6M

Color Temp: Warm White : 3000k - White Each 35.00 15000.00 0.00 525000.00

Supply, installation, wiring, testing and commissioing of prewired Ground burial light

fixtures with housing and lamp, ballast, transformers, drivers complete with all

accessories etc. including making PCC foundation embedding in ground, providing

nuts and bolts, 3C1.5 sq.mm. copper flexible cord from the loop-in-loop-out box up to

the light fixture etc. complete in all respect.

Model No. : SPYK2-BGSBL 9W LED WW

Housing: Graphite grey powder coated integral aluminium

Color Temp: Warm White : 3000k - White Each 20.00 15000.00 0.00 300000.00

Supply, installation, wiring, testing and commissioing of prewired Bollard light fixtures

with lamp,ballast, transformers, drivers complete with all accessories etc. including

223 A/R on MR making PCC foundation, providing nuts and bolts, 3C 1.5 sq.mm. copper flexible

cord from the loop-in-loop-out box up to the light fixture etc. complete in all respect.

Model No. : TETRIS-BGOS605 9W LED

Housing: Graphite grey powder coated square extruded aluminium

Color Temp: Warm White : 3000k - White Each 10.00 15000.00 0.00 150000.00

Supply, installation, wiring, testing and commissioing of wall recessed LED light

224 A/R on MR fixture with lamp, ballast, transformers, drivers including cutting the required size

opening in wall and making good the same

Model No. : VERTICO-BLWUP 9W LED WW

Housing: Graphite grey powder coated integral aluminium

Color Temp: Warm White : 3000k - White Each 20.00 10000.00 0.00 200000.00

Supply and installation of loop-in loop-out box made of polycarbonate having IP-68

rating, approximate size 100X100X65MM with screwless three pole three way

terminal with grommets for outgoing cord etc. complete as required.

Total: Subhead 13 0.00 2972500.00

Sub Head 1 : SANITARY FIXTURES AND TOILET REQUISITES

17.7A Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole

226 basin mixer of approved quality and make, including painting of fittings and brackets,

cutting and making good the walls wherever required:-

(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass

single hole basin mixer

17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983

227 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and

brackets, cutting and making good the walls wherever required :

17.10.1 Kitchen sink with drain board

17.78 Providing and fixing white vitreous china extended wall mounting water closet of size

780x370x690 mm of approved shape including providing & fixing white vitreous

228 china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 Each 452.00 13852.45 6261307.40 0.00

litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc

17.80 Providing and fixing white vitreous china battery based infrared sensor operated

urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250

229 ml & 500 ml consumption), having water inlet from back side, including fixing to wall Each 10.00 6913.90 69139.00 0.00

with suitable brackets all as per manufacturers specification and direction of

Engineer-in-charge.

AR on MR Providing and fixing of brass single flow shower with revolving ball joint and 190 mm

long branch light body shower arm with wall flange. (or equal approved).

a) Model : Jaquar Continental

Colour/Finish : Chrome Each 447.00 3800.00 0.00 1698600.00

AR on MR Providing and fixing of wall mounted bath cum shower mixer fitting with diverter lever

and bend for overhead shower connection including making connections with water

231 supply, cutting and making good the walls wherever required. (or equal approved).

17.22A Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make

and as per the direction of Engineer-in-charge.

AR on MR Providing and fixing of 15 mm dia brass angle valve (inlet fitting ball valve type)

233 having strainer screen complete with wall flange of following make and model:(or

equal approved)

Make : ARCO, Spain

Colour/Finish : Chrome Each 3090.00 550.00 0.00 1699500.00

AR on MR Providing and fixing of 15 mm dia, 450 mm long flexible connection pipe having

234 EPDM rubber internal core and stainless steel braided outer sheath complete with Each 2638.00 300.00 0.00 791400.00

C.P brass end nuts, of approved make.

AR on MR Providing and fixing C.P brass ablution faucet (health faucet) comprising hand held

shower with operating lever, 1 m long flexible tube and wall hook all complete.

Model : Continental

Cat. No. : 573

Colour/Finish : Chrome Each 452.00 2150.00 0.00 971800.00

236 AR on DSR Providing and fixing CP Brass 32mm size waste fitting for wash basin complete. Each 451.00 112.00 0.00 50512.00

AR on MR Providing and fixing of 15 mm dia. C.P. brass wall-mounted Kitchen sink mixer with

237 swivel spout and wall flange of following make.(or equal approved).

Model : Continental

Cat. No. : 319KN

Colour/Finish : Chrome Each 116.00 3550.00 0.00 411800.00

AR on MR Providing and fixing electric water storage heater (geyser) of following capacities

including making inlet / outlet connections, of approved makes.

17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste

fittings complete.

17.28.2 Flexible pipe

18.51 Providing and fixing C.P. brass long body bib cock of approved quality conforming to

IS standards and weighing not less than 690 gms.

Total : Sub Head No. 1 Rs. 11477960.70 12018812.00

Sub Head 2 : SOIL, WASTE & VENT AND RAIN WATER PIPEWORK

241 17.35 Providing and fixing soil, waste and vent pipes :

17.35.1.2 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989. Metre 7282.00 1092.20 7953400.40 0.00

17.35.2.2 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989. Metre 2134.00 992.05 2117034.70 0.00

17.37 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast

iron/cast iron (spun) pipe embedded in and including cement concrete blocks

242 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20

mm nominal size) including cost of cutting holes and making good the walls etc. :

17.38 Providing and fixing bend of required degree with access door, insertion rubber

washer 3 mm thick, bolts and nuts complete

17.38.1.2 Sand cast iron S&S as per IS - 3989 Each 4.00 461.65 1846.60 0.00

244 17.39 Providing and fixing plain bend of required degree.

17.39.2.2 Sand cast iron S&S as per IS : 3989 Each 72.00 289.75 20862.00 0.00

17.43 Providing and fixing single equal plain junction of required degree with access door,

insertion rubber washer 3 mm thick, bolts and nuts complete.

246 17.44 Providing and fixing single equal plain junction of required degree :

17.44.1.2 Sand cast iron S&S as per IS - 3989 Each 2.00 667.70 1335.40 0.00

247 17.49 Providing and fixing double equal plain invert branch of required degree:

17.49.1.2 Sand cast iron S&S as per IS - 3989 Each 1.00 745.30 745.30 0.00

248 17.50 Providing and fixing single equal plain invert branch of required degree:

17.50.1.2 Sand cast iron S&S as per IS - 3989 Each 30.00 604.80 18144.00 0.00

249 17.56 Providing and fixing terminal guard

17.56.1.2 Sand cast iron S&S as per IS - 3989 Each 98.00 389.40 38161.20 0.00

17.56.2.2 Sand cast iron S&S as per IS - 3989 Each 44.00 309.85 13633.40 0.00

17.58 Providing lead caulked joints to sand cast iron / centrifugally cast (spun) iron pipes

and fittings of diameter.

17.59 Providing and fixing M.S. stays and clamps for sand cast iron / centrifugally cast

(spun) iron pipes of diameter.

17.65 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and

fittings with two coats of synthetic enamel paint of any colour such as chocolate grey,

or buff etc. over a coat of primer (of approved quality) for new work :

18.12 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and

For Waste line in toilets and Kitchen

18.38 Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over

254 a ready mixed priming coat, both of approved quality for new work :.

For Waste line in toilets and Kitchen

a 18.38.4 32 mm dia. nominal bore Metre 649.00 28.40 18431.60 0.00

17.61 Cutting chases in brick masonry walls for following diameter sand cast iron/

centrifugally cast (spun) iron pipes and making good the same with cement concrete

255 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size),

including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse

For Waste line in toilets and Kitchen

12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes

256 conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :

5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes.

12.42 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes

257 conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :

5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes.

12.42.2 Single pushfit Coupler :

c 12.42.3 Single tee with door

d 12.42.4 Single tee without door

12.43 Providing and fixing unplasticised -PVC pipe clips of approved design to

unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs,

258 screwed with M.S. screws of required length including cutting brick work and fixing in

cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc.

259 12.44 diameter and weighing not less than 440 grams. Each 677.00 47.25 31988.25 0.00

AR on DSR Providing and fixing of floor traps formed of Cast Iron 'P' traps complete, including

260 cost of cutting and making good the walls and floors wherever required.

a) 100 mm inlet and 100 mm outlet Each 565.00 1200.00 0.00 678000.00

AR on MR Providing and fixing floor trap Extension Piece made out of 100 mm dia M.S. pipe

(heavy grade C-Class) of required length (upto 450 mm) with 32 mm to 50 mm dia

threaded maleable iron sockets ( maximum 4 nos.) welded as side inlets, neatly

finished, inside and outside painted with 2 coats of redoxide primer & 2 coats of

synthetic enamel paint, including the cost of jointing with floor trap with dripseal joint.

AR on MR Providing and fixing floor drain points formed out of 100 X 50 mm dia reducing

262 elbow with suitable extension piece including cost of cutting and making good the Each 467.00 1600.00 0.00 747200.00

walls and floors wherever required.

AR on MR Providing and fixing 125 mm dia round chrome plated bronze grating with frame,

screw down type embedded in floor, all complete.

AR on MR Providing and fixing screwed down type nickel bronze alloy cast floor cleanout with

2 opening arrangements for soil / waste pipe and other necessary fittings inlcuding

jointing, all complete as per standard detail.

AR on MR Providing and fixing cleanout with opening arrangements by providing 300 mm long

G.I. nipple welded to 6 mm thick flange sealed with 6 mm thick blank flange including

nuts and bolts, rubber insertions etc. all complete as per standard detail.

265 17.48 Providing and fixing single unequal plain junction of required degree :

17.48.1.2 Sand cast iron S&S as per IS - 3989 Each 55.00 798.80 43934.00 0.00

266 17.52 Providing and fixing single unequal plain invert branch of required degree :

267 AR on MR Providing and fixing soil, waste and vent pipes :

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989. Metre 902.00 1400.00 0.00 1262800.00

268 AR on MR Providing and fixing single unequal plain invert branch of required degree :

Sand cast iron S&S as per IS - 3989 Each 200.00 1200.00 0.00 240000.00

AR on MR Providing lead caulked joints to sand cast iron / centrifugally cast (spun) iron pipes

and fittings of diameter.

AR on MR Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and

fittings with two coats of synthetic enamel paint of any colour such as chocolate grey,

or buff etc. over a coat of primer (of approved quality) for new work :

150 mm diameter pipe Metre 902.00 100.00 0.00 90200.00

Total : Sub Head No. 2 Rs. 23634683.95 5555010.00

Sub Head 3 : WATER SUPPLY

18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

271 fittings, including fixing the pipe with lamps at 1.00 m spacing. This includes jointing

of pipes & fittings with one step CPVC solvent cement and testing of joints complete

as per direction of Engineer in Charge.

Internal work – Exposed on wall

a 18.7.1 15 mm nominal outer dia .Pipes. Metre 352.00 241.55 85025.60 0.00

b 18.7.2 20 mm nominal outer dia .Pipes. Metre 985.00 306.95 302345.75 0.00

c 18.7.3 25 mm nominal outer dia .Pipes. Metre 1606.00 369.20 592935.20 0.00

d 18.7.4 32 mm nominal outer dia .Pipes. Metre 1744.00 480.55 838079.20 0.00

e 18.7.5 40 mm nominal outer dia .Pipes. Metre 1711.00 648.60 1109754.60 0.00

f 18.7.6 50 mm nominal outer dia .Pipes. Metre 1535.00 903.50 1386872.50 0.00

18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply including all CPVC plain & brass threaded fittings

i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement and the cost of cutting chases and

making good the same including testing of joints complete as per direction of

Engineer in Charge

Concealed work including cutting chases and making good the walls etc.

a 18.8.1 15 mm nominal outer dia .Pipes. Metre 15499.00 409.65 6349165.35 0.00

b 18.8.2 20 mm nominal outer dia .Pipes. Metre 6028.00 478.15 2882288.20 0.00

c 18.8.3 25 mm nominal outer dia .Pipes. Metre 28.00 561.95 15734.60 0.00

d 18.8.4 32 mm nominal outer dia .Pipes. Metre 11.00 679.15 7470.65 0.00

18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply including all CPVC plain & brass threaded fittings

273 This includes jointing of pipes & fittings with one step CPVC solvent cement

,trenching ,refilling & testing of joints complete as per direction of Engineer in

a 18.9.1 15 mm nominal outer dia .Pipes. Metre 22.00 202.85 4462.70 0.00

b 18.9.2 20 mm nominal outer dia .Pipes. Metre 39.00 253.70 9894.30 0.00

c 18.9.3 25 mm nominal outer dia .Pipes. Metre 39.00 326.65 12739.35 0.00

d 18.9.4 32 mm nominal outer dia .Pipes. Metre 11.00 413.70 4550.70 0.00

e 18.9.5 40 mm nominal outer dia .Pipes. Metre 11.00 536.75 5904.25 0.00

f 18.9.6 50 mm nominal outer dia .Pipes. Metre 407.00 791.65 322201.55 0.00

18.13 Making connection of G.I. distribution branch with G.I. main of following sizes by

274 providing and fixing tee,including cutting and threading the pipe etc. complete

18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank

ISI : 12701 marked with cover and suitable locking arrangement and making

necessary holes for inlet, outlet and overflow pipes but without fittings and the base

support for tank

AR on MR Providing and fixing of nickel plated brass/ nonferrous alloy fullyway ball valve (

276 minimum working pressure of 20 bar ) with operating handle of approved make.

AR on MR Providing and fixing Cast Iron butterfly valve as per IS: 13095 of Class PN 10,

having epoxy coated disc, carbon steel shaft, EPDM / nitrile rubber field replacible

body lining and of approved make. including a set of MS flanges, required nos. of nut

& bolts all complete.

AR on MR Providing and fixing insulation to hot water piping with closed cell polyolefine foam

preformed pipe sleeves of specified wall thickness using propriety adhesive and self

adhesive tapes, all as per the manufacturer's specifications.

a) 15 mm dia - 9 mm thickness Metre 5203.00 115.00 0.00 598345.00

b) 20 mm dia - 9 mm thickness Metre 2992.00 122.00 0.00 365024.00

c) 25 mm dia - 13 mm thickness Metre 259.00 175.00 0.00 45325.00

d) 32 mm dia - 13 mm thickness Metre 237.00 203.00 0.00 48111.00

e) 40 mm dia - 13 mm thickness Metre 259.00 233.00 0.00 60347.00

f) 50 mm dia - 20 mm thickness Metre 33.00 427.00 0.00 14091.00

AR on MR Extra for providing and wrapping with 5 mile glass cloth on hot water lines insulation

279 and applying of coat of hardner paint of approved shade, all complete in a

workmanship like manner ( on exposed pipework)

a) 15 mm dia pipe plus insulation Metre 66.00 82.00 0.00 5412.00

b) 20 mm dia pipe plus insulation Metre 105.00 99.00 0.00 10395.00

c) 25 mm dia pipe plus insulation Metre 259.00 116.00 0.00 30044.00

d) 32 mm dia pipe plus insulation Metre 226.00 141.00 0.00 31866.00

e) 40 mm dia pipe plus insulation Metre 242.00 169.00 0.00 40898.00

f) 50 mm dia pipe plus insulation Metre 33.00 206.00 0.00 6798.00

AR on MR Supplying, Installing, Testing and Commissioning of Solar Water Heating System

as per following details

i) Method of Circulation - Closed Circuit Thermo-siphon

ii) Method of Water Heating - Indirect - either through jacketed hot water storage tank

or through coil type heat exchanger fixed within hot water storage tank.

iii) Solar Collector Panel:

Absorptivity Factor - 0.95

Emittance Factor - 0.1

Type - Flat bed Collector Panel

Size - 2M X 1M (Nominal Size)

MOC - Copper Water grid, black polyester coated full sheet absorber, toughened

glass, weather proof aluminium casing, mineral wool insulation

Other specification

Standard - Shall be inline with IS: 12933 part-1.

iv) Hot Water Storage Tank:

Working pressure - 2.5 kg/cm2 (Minimum)

MOC - Stainless Steel - SS 316 grade OR SS316 lined OR ceramic lined complete

with 50 mm thick PUF insulation, duly protected; and inlet-outlet nozzles. The tank

shall be fitted with a sacrificial anode.

v) Interconnecting Pipework : All interconnecting pipework in Medium Class (Class-

B) G.I. Pipe with Heavy Class malleable cast iron fitings suitable for threaded joints

and valves. G.I. Pipe work conforming to IS:1239 (Part I)-1990 and G.I. fittings

conforming to IS: 1879

Battery Limits: Between Solar panels and hot water collection tank.

vi) Accessories: Pressure gauges, Safety valve etc.

vii) Mounting structure: Mounted on Galvanized Steel frame

(i) 400 litres per day with 4 no. collector plates No. 9.00 220000.00 0.00 1980000.00

AR on MR Supplying pressure reducing valve, suitable for water application and having

following features:

Body — Forged Brass / Bronze

Seat — Stainless Steel

Ends — Female Screwed Ends

Maximum Working Pressure — Upto 16 bar

Adjustable Pressure Range — 1.0 bar (Minimum) - 6.0 bar

Provision for installing Pressure Gauge : 1/4 inch port

AR on MR Providing and fixing in position the medium class (Class B) G.I. pipes (IS:1239) with

all fittings, specials & clamps effecting proper connections, cutting and making good

the walls and floors etc. (Internal Work). Note: Pipe work in shafts, ceiling voids and

282 terrace shall be supported/ fixed on MS structural supports with U-clamps complete

with nuts and washers.Cost for MS structural work for supports shall be included in

the rates all complete. ( At terrace level and riser mains)

AR on DSR Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over

283 a ready mixed priming coat, both of approved quality for new

2.10 Excavating trenches of required width for pipes, cables, etc including excavation for

sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including

getting out the excavated soil, and then returning the soil as required, in layers not

exceeding 20 cm in depth, including consolidating each deposited layer by ramming,

watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50

2.10.1 All kinds of soil

2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. Metre 446.00 223.00 99458.00 0.00

Total : Sub Head No. 3 Rs. 14235291.40 6153271.00

Sub Head 4 : SEWERAGE AND STORM WATER DRAINAGE

19.1 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of

285 cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of

joints etc. complete :

19.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded

286 stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete

as per standard design :

4.1 Providing and laying in position cement concrete of specified grade excluding the

cost of centering and shuttering - All work up to plinth level :

Bed concrete for RCC NP2 Pipe

4.1.5 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) Cum. 171.00 6259.10 1070306.10 0.00

19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars

288 jointed with stiff mixture of cement mortar in the proportion of 1 : 2 (1 cement : 2 fine

sand) including testing of joints etc. complete.

19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse

sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4

coarse sand : 8 graded stone aggregate 40mm nominal size), inside plastering

289 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating

coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating

coat of neat cement complete as per standard design :

19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty)

455x610 mm internal dimensions, total weight of cover and frame to be not less than

38 kg (weight of cover 23 kg and weight of frame 15 kg) :

19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 42.00 10905.05 458012.10 0.00

290 19.8 Extra for depth for manholes.

19.8.1 Size 90x80 cm

19.8.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Metre 6.00 7503.00 45018.00 0.00

19.9 Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and

0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), in side cement

plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with

a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse

291 sand : 6 graded stone aggregate 40 mm nominal size), and making necessary

channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size) finished with a floating coat of neat cement, all

complete as per standard design :

19.9.1 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation)

560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame

to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand

: 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all

complete. (Excavation, foot rests and 12mm thick cement plaster at the external

surface shall be paid for separately) :

19.9.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 32.00 11038.10 353219.20 0.00

19.10 Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m

19.10.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Metre 14.00 6448.40 90277.60 0.00

19.11 Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56

m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster

12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a

floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6

graded stone aggregate 40 mm nominal size) and making necessary channel in

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) finished with a floating coat of neat cement, all complete as per

standard design :

19.11.1 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560

mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be

not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size) including centering, shuttering all

complete. (Excavation, foot rests and 12 mm thick cement plaster at the external

surface shall be paid for separately) :

19.11.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 2.00 21235.65 42471.30 0.00

19.12 Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m

19.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.16 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated

as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum

cross section as 23 mmx25 mm and over all minimum length 263 mm and width as

165 mm with minimum 112 mm space between protruded legs having 2 mm tread on

top surface by ribbing or chequering besides necessary and adequate anchoring

projections on tail length on 138 mm as per standard drawing and suitable to with

stand the bend test and chemical resistance test as per specifications and having

manufacture’s permanent identification mark to be visible even after fixing, including

fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3

coarse sand : 6 graded stone aggregate 20 mm nominal

size) complete as per design.

296 13.4 12 mm cement plaster of mix :

For external surface plaster of 0.91 m dia, 1.22 m dia & 1.52 m dia manhole

297 19.27 mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C.

19.27.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 140.00 5209.10 729274.00 0.00

2.10 Excavating trenches of required width for pipes, cables, etc including excavation for

sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including

getting out the excavated soil, and then returning the soil as required, in layers not

exceeding 20 cm in depth, including consolidating each deposited layer by ramming,

watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50

2.10.1 All kinds of soil

a 2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. Metre 0.00 223.00 0.00 0.00

b 2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia Metre 2431.00 364.20 885370.20 0.00

c 2.10.1.3 Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm Metre 11.00 568.60 6254.60 0.00

2.11 Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth

299 exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for

depth upto 1.5 metre).

a Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia Metre 187.00 462.53 86493.11 0.00

b Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm Metre 11.00 722.12 7943.32 0.00

19.3 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded

300 stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed

concrete as per standard design :

For R.C.C. NP2 PIPE

AR on MR Providing, Laying, Jointing and Testing of HDPE Pipes and Fittings.(For

surplus effluent discharge from STP bye-pass line)

The work shall be done as per specifications and in general shall include:

a) Providing HDPE pipes (of PE 80 grade as per IS 4984-1995). The pipes shall

have a working pressure of PN 10.

b) Providing factory fabricated and moulded fittings (including flanged tail pieces, slip

on flanges, flanges with welding neck etc.) suitable for butt jointing and flange

jointing as the case may be. The fitting shall be rated PN16 upto 63 mm OD and

PN10 for 75 mm OD and above.

c) Laying in position in excavated trenches. (Excavation of trenches to be paid

seperately as per relevant item)

d) Jointing by heat fusion technique.

e) Providing and laying LDPE/PVC warning tape ( in florescent colour) of size 25 mm

wide and 50 micron thick. The warning tape shall be laid 150 mm above the pipe

AR on MR Providing and fixing moulded HDPE compression type (as specified) adaptor

302 fittings, saddles, etc. for connecting HDPE pipework to pipework of other materials

and appurtenances including jointing, testing etc. all complete.

a) Compression Flange Adaptor

4.1 Providing and laying in position cement concrete of specified grade excluding the

cost of centering and shuttering - All work up to plinth level :

For thrust blocks

4.1.3 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cum. 0.10 6788.60 678.86 0.00

18.41 Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes

in external work :

18.31 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber

insertions etc. (the tail pieces if required will be paid separately) :

18.31.1 100 mm diameter

19.21 Making connection of drain or sewer line with existing manhole including breaking

into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on

both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating

coat of neat cement and making necessary channels for the drain etc. complete :

a 19.21.1 For pipes 100 to 250 mm diameter each 1.00 623.50 623.50 0.00

b 19.21.3 For pipes 350 to 450 mm diameter each 2.00 1035.45 2070.90 0.00

AR on MR BOREWELL CUM DUGWELL : Constructing a borewell cum dugwell ground

307 water recharge structure generally as per enclosed standard detail and having Job 6.00 500000.00 0.00 3000000.00

following construction specifications :

Volume of Dugwell : 38 Cum.

Peripherical brick masonry in cement mortar 1:4 ( 1 cement:4 coarse sand) with

necessary 15 mm thick cement plaster 1:3 neat finish.

Foundation concrete for walls 1:5:10 (300mm thick)

Providing and laying in position 300 mm thick 5-10 mm size gravel

Providing and laying in position 300 mm thick 5-15 cm size gravel

Providing and laying in position 300 mm thick dry stone aggregate bed (40 to 65 mm

200 mm thick R.C.C ( 1:2:4) slab to cover the well at top including necessary

centring, shuttring and reinforcement with required opening/cutouts etc. supplying &

fixing 600 mm X 600 mm S.F.R.C Manhole cover / frame( total weight 208 Kg.)

heavy duty type, all complete as per drawings.

1 No. 160 mm dia PVC blind/ perforated pipe lowered vertically upto first granular

saturated sandy formation including necessary drilling / boring in ground in all kinds

Providing and packing suitable size pea gravel all around casing pipe in the bore

Supplying & fixing P.V.C foot rests.

Making all inlets & outlets in brick masonry walls including cutting holes & making

10-12 mm thick cement plaster 1:3 mixed with water profing compound on top of

R.C.C slabs & in ceiling of slab, finished smooth.

Note: Dimensions may vary as per the site conditions.

Total : Sub Head No. 4 Rs. 5820367.04 3069861.00

Sub Head 5 : EXTERNAL WATER SUPPLY AND LANDSCAPE IRRIGATION

308 AR on MR Providing, Laying, Jointing and Testing of HDPE Pipes and Fittings.

The work shall be done as per specifications and in general shall include:

a) Providing HDPE pipes (of PE 80 grade as per IS 4984-1995). The pipes shall

have a working pressure of PN 10.

b) Providing factory fabricated and moulded fittings (including flanged tail pieces, slip

on flanges, flanges with welding neck etc.) suitable for butt jointing and flange

jointing as the case may be. The fitting shall be rated PN16 upto 63 mm OD and

PN10 for 75 mm OD and above.

c) Laying in position in excavated trenches. (Excavation of trenches to be paid

seperately as per relevant item)

d) Jointing by heat fusion technique.

e) Providing and laying LDPE/PVC warning tape ( in florescent colour) of size 25 mm

wide and 50 micron thick. The warning tape shall be laid 150 mm above the pipe

AR on MR Providing and fixing moulded HDPE compression type (as specified) adaptor

309 fittings, saddles, etc. for connecting HDPE pipework to pipework of other materials

and appurtenances including jointing, testing etc. all complete.

a) Compression Flange Adaptor

b) 90 degree Elbow with threaded female offtake

4.1 Providing and laying in position cement concrete of specified grade excluding the

cost of centering and shuttering - All work up to plinth level :

For thrust blocks

4.1.3 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cum. 5.00 6788.60 33943.00 0.00

18.41 Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes

in external work :

18.31 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber

insertions etc. (the tail pieces if required will be paid separately) :

18.31.1 100 mm diameter

AR on MR Providing and fixing C.I. sluice valves with hand wheel complete with bolts, nuts,

rubber insertions etc. (as per IS:14846)

AR on MR Providing, fixing, testing and commissioning of Full Bore Ball Valves of approved

Body : Nickel plated brass

Ball : Chrome plated brass

Operating Handle : Aluminium/ Steel with protective colour coded sleeve

Pressure Rating : Minimum 20 Bar

Temerature Withstanding : 900 C Min.

AR on MR Providing, installing and commissioning 20 mm dia brass quick release coupling

valves, complete with lid, preassembled triple swing joint in PVC, GI support rod with

SS hose clamps all complete as per standard detail including making connections

with main supply line.

316 AR on MR Supply of Quick Coupling Keys complete with Swivel elbow complete Nos. 5.00 1000.00 0.00 5000.00

AR on MR Providing and installing HDPE Valve Boxes with screw down type covers, of

following sizes and shape, including excavation and filling of pea gravel in 100 mm

deep layer at bottoms, all as per standared detail ( for QRCV, Ball Valves, Butterfly

Valves, Flush points etc.)

18.33 Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar

1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top

diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and

RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm

318 nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5

fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering

with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a

floating coat of neat cement complete as per standard design :

18.33.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 each 9.00 9288.40 83595.60 0.00

2.10 Excavating trenches of required width for pipes, cables, etc including excavation for

sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including

getting out the excavated soil, and then returning the soil as required, in layers not

exceeding 20 cm in depth, including consolidating each deposited layer by ramming,

watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50

2.10.1 All kinds of soil

2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. M 1200.00 223.00 267600.00 0.00

2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia M 280.00 364.20 101976.00 0.00

19.35 Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including

collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1

cement : 2 fine sand) including testing of joints etc. complete

18.80 Disinfecting C.I. water mains by flushing with water containing bleaching powder @

0.5 gms per litre of water and cleaning the same with fresh water, operation to be

repeated three times including getting the sample of water from the disinfected main

tested in the municipal laboratory.

18.59 Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts,

322 rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid

Total : Sub Head No. 5 Rs. 1138791.79 1153058.00

MISCELLANEOUS ITEMS

10.15 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and

cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet,

323 joints mitred, welded and grinded finish, with profiles of required size, including fixing

of necessary butt hinges and screws and applying a priming coat of approved steel

10.15.1 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10

cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm Kg 450.00 137.30 61785.00 0.00

AR on MR Providing and fixing G.I. vent pipe with antimosquito grating of the following sizes (for

under ground/over head water tanks only) :

AR on MR Providing and fixing in position following sizes pipe inserts with puddle flanges,

fabricated with heavy duty MS pipe pieces conforming to IS: 1239 and puddle flange

made of 6 mm thick MS plate welded to the pipe piece, entire piece hot dipped

galvanised, all complete as per Standard Detail, including fixing at desired position in

the form work for RCC walls / slabs before pouring of concrete.

326 AR on MR Providing, fixing, testing and commissioning of Water level controller in Overhead

The water level controller shall comprise of the following:

a) Magnetic float type level sensing unit of stainless steel or any other non corrosive

b) Motorized valve/ Solenoid valve

c) Level controller unit including power supply in a weather proof enclosure

(minimum IP65 rated)

d) Interconnecting wiring duly protected and properly clamped

e) Mounting arrangement for the components described at (a), (b) and (c)

Note: Power supply at 220 volts, 50 Hz. Would be provided by others on the nearest

Total : Sub Head No. 6 Rs. 61785.00 720500.00

Sub Head 7 : PUMPING MACHINERY AND ALLIED EQUIPMENTS

NOTE: The Vendor has to get the technical data sheets of all the equipment

7 HYDROPNEUMATIC SYSTEM FOR RESIDENTIAL AND CLUB BLOCK FOR

AR on MR Supply, installing, testing and commissioning of clear water Factory Fitted packaged

327 hydropneumatic pumping system for general water supply as per following details:

Type of Drive - Variable frequency drive for each pump

Discharge (each pump):10 M3/hr.

System Pressure : 7.0 kg/cm2

Pumps- 2 Nos. (1 working + 1 standby)

The packaged unit shall be complete with :

a) Pumps: Vertical inline booster pumpset with mechanical seal

Material of Construction (M.O.C):

: Impeller — Stainless Steel -AISI 304

: Shaft — Stainless Steel - AISI 304

: Pump Head — Cast Iron/ Stainless

: Base — Cast Iron

: Motor Stool — Cast Iron

Motor: 2900 RPM; 3Ph 415V 50Hz

Insulation Class - F

Efficiency - IE2 Min.

Protection - IP54 Min.

b) Pressure Tank: FRP vessel with replacable polyetheruethane (PEU) bladder

certified for drinking water. Minimum 10 Bar pressure rating — 1 No. of 200 to

250 Lts. Capacity.

c) Interconnecting Pipe work and Valves: Common suction & delivery headers

in hot dipped galvanized iron, Isolating valves on suction & delivery side, non

return valves on delivery side of pumps.

d) Common fabricated base frame, duly painted.

e) Power and control cabling between panel and pumps.

f) Accessories like presure guages, pressure transducers etc.

g) System Control Panel : The system control panel shall be factory built and

tested and shall have the following minimum features:

i) Fully protected, powder coated metallic housing.

ii) Complete switchgear, under/over voltage protection, single phase

preventors etc.

iii) VFDs for all the pumps

iv) Site programmable application optimised software

v) Integrated Modbus interface for BMS compatibility

vi) Large graphic display with as easy to use menu.

Programmable Control System shall be PLC based, duly authentiated by the

Pump Manufacturer.

The pump Panel shall be also to convese with Building Management System

Notes: 1) Switchgear and starter ratings are indicative. The Tenderer shall

quote for the actual rating required as per the pump model proposed by him.

2) Provision for BMS connectivity. The panel should have sufficient no. of

potential free contacts for connectivity with Building Management System for

monitoring purposes

HYDROPNEUMATIC SYSTEM FOR RESIDENTIAL AND CLUB BLOCK FOR

AR on MR Supply, installing, testing and commissioning of clear water Factory Fitted packaged

328 hydropneumatic pumping system for treated effluent supply for flushing as per

following details:

Type of Drive - Variable frequency drive for each pump

Discharge (each pump): 6 M3/hr.

System Pressure : 7.0 kg/cm2

Pumps- 2 Nos. (1 working + 1 standby)

The packaged unit shall be complete with :

a) Pumps: Vertical inline booster pumpset with mechanical seal

Material of Construction (M.O.C):

: Impeller — Stainless Steel -AISI 304

: Shaft — Stainless Steel - AISI 304

: Pump Head — Cast Iron/ Stainless

: Base — Cast Iron

: Motor Stool — Cast Iron

Motor: 2900 RPM; 3Ph 415V 50Hz

Insulation Class - F

Efficiency - IE2 Min.

Protection - IP54 Min.

b) Pressure Tank: FRP vessel with replacable polyetheruethane (PEU) bladder

certified for drinking water. Minimum 10 Bar pressure rating — 1 No. of 200 to

250 Lts. Capacity.

c) Interconnecting Pipe work and Valves: Common suction & delivery headers

in hot dipped galvanized iron, Isolating valves on suction & delivery side, non

return valves on delivery side of pumps.

d) Common fabricated base frame, duly painted.

e) Power and control cabling between panel and pumps.

f) Accessories like presure guages, pressure transducers etc.

g) System Control Panel : The system control panel shall be factory built and

tested and shall have the following minimum features:

i) Fully protected, powder coated metallic housing.

ii) Complete switchgear, under/over voltage protection, single phase

preventors etc.

iii) VFDs for all the pumps

iv) Site programmable application optimised software

v) Integrated Modbus interface for BMS compatibility

vi) Large graphic display with as easy to use menu.

Programmable Control System shall be PLC based, duly authentiated by the

Pump Manufacturer.

The pump Panel shall be also to convese with Building Management System

Notes: 1) Switchgear and starter ratings are indicative. The Tenderer shall

quote for the actual rating required as per the pump model proposed by him.

2) Provision for BMS connectivity. The panel should have sufficient no. of

potential free contacts for connectivity with Building Management System for

monitoring purposes

HYDRO-PNEUMATIC SYSTEMS - FOR TWO UPPER FLOORS OF TOWERS-

AR on MR Supply, installing, testing and commissioning of clear water packaged

hydropneumatic pumping system for general water supply for two upper floors of

each tower (with a single VFD common for both pumps) as per following details:

The packaged unit shall be complete with :

a) Pumps: Horizontal monoblock / Vertical inline booster pumpset with

mechanical seal

2 nos. (1 working+1 standby)

Material of Construction (M.O.C):

: Impeller — Stainless Steel -AISI 304

: Shaft — Stainless Steel - AISI 304

: Pump Head — Cast Iron

: Base — Cast Iron

: Motor Stool — Cast Iron

Motor: 2900 RPM; 3Ph 415V 50Hz

Insulation Class - F

Efficiency - IE2 Min.

Protection - IP54 Min.

Discharge ( each pump) : 6.0 M3/hr.

Working Pressure : 2.5 kg/sq.cm.

b) Pressure Tank: FRP vessel with replacable polyetheruethane (PEU) bladder

certified for drinking water. Minimum 8 Bar pressure rating — 1 No. 200 Lts.

c) Interconnecting Pipe work and Valves : Common suction & delivery

headers in hot dipped galvanised iron, Isolating valves and non return valves

on suction & delivery side of pumps.

d) Common fabricated base frame, duly painted.

e) Power and control cabling between panel and pumps.

f) Accessories like presure guages, pressure switches etc.

g) Electric control panel mounted on the skid for automatic operation of

pumps comprising incoming switch fuse unit/MCBB, digital voltmeter &

ammeter with selector switches, over load and under voltage protection

devices, single phase preventors, MCB and DOL starter for each pump,

indicating lights etc. all complete.

Programmable Control System shall be PLC based, duly authentiated by the

Pump Manufacturer.

Notes: 1) Switchgear and starter ratings are indicative. The Tenderer shall

quote for the actual rating required as per the pump model proposed by him.

2) Provision for BMS connectivity. The panel should have sufficient no. of

potential free contacts for connectivity with Building Management System for

monitoring purposes

HYDRO-PNEUMATIC SYSTEMS - FOR TWO UPPER FLOORS OF TOWERS-

TYPE- V (To be installed at terrace level)

AR on MR Supply, installing, testing and commissioning of clear water packaged

hydropneumatic pumping system for general water supply for two upper floors of

each tower (with a single VFD common for both pumps) as per following details:

The packaged unit shall be complete with :

a) Pumps: Horizontal monoblock / Vertical inline booster pumpset with

mechanical seal

2 nos. (1 working+1 standby)

Material of Construction (M.O.C):

: Impeller — Stainless Steel -AISI 304

: Shaft — Stainless Steel - AISI 304

: Pump Head — Cast Iron

: Base — Cast Iron

: Motor Stool — Cast Iron

Motor: 2900 RPM; 3Ph 415V 50Hz

Insulation Class - F

Efficiency - IE2 Min.

Protection - IP54 Min.

Discharge ( each pump) : 4.0 M3/hr.

Working Pressure : 2.5 kg/sq.cm.

b) Pressure Tank: FRP vessel with replacable polyetheruethane (PEU) bladder

certified for drinking water. Minimum 8 Bar pressure rating — 1 No. 200 Lts.

c) Interconnecting Pipe work and Valves : Common suction & delivery

headers in hot dipped galvanised iron, Isolating valves and non return valves

on suction & delivery side of pumps.

d) Common fabricated base frame, duly painted.

e) Power and control cabling between panel and pumps.

f) Accessories like presure guages, pressure switches etc.

g) Electric control panel mounted on the skid for automatic operation of

pumps comprising incoming switch fuse unit/MCBB, digital voltmeter &

ammeter with selector switches, over load and under voltage protection

devices, single phase preventors, MCB and DOL starter for each pump,

indicating lights etc. all complete.

Programmable Control System shall be PLC based, duly authentiated by the

Pump Manufacturer.

Notes: 1) Switchgear and starter ratings are indicative. The Tenderer shall

quote for the actual rating required as per the pump model proposed by him.

2) Provision for BMS connectivity. The panel should have sufficient no. of

potential free contacts for connectivity with Building Management System for

monitoring purposes

HYDRO-PNEUMATIC SYSTEMS - FOR TWO UPPER FLOORS OF TOWERS-

TYPE-VI (To be installed at terrace level)

AR on MR Supply, installing, testing and commissioning of clear water packaged

hydropneumatic pumping system for general water supply for two upper floors of

each tower (with a single VFD common for both pumps) as per following details:

The packaged unit shall be complete with :

a) Pumps: Horizontal monoblock / Vertical inline booster pumpset with

mechanical seal

2 nos. (1 working+1 standby)

Material of Construction (M.O.C):

: Impeller — Stainless Steel -AISI 304

: Shaft — Stainless Steel - AISI 304

: Pump Head — Cast Iron

: Base — Cast Iron

: Motor Stool — Cast Iron

Motor: 2900 RPM; 3Ph 415V 50Hz

Insulation Class - F

Efficiency - IE2 Min.

Protection - IP54 Min.

Discharge ( each pump) : 5.0 M3/hr.

Working Pressure : 2.5 kg/sq.cm.

b) Pressure Tank: FRP vessel with replacable polyetheruethane (PEU) bladder

certified for drinking water. Minimum 8 Bar pressure rating — 1 No. 200 Lts.

c) Interconnecting Pipe work and Valves : Common suction & delivery

headers in hot dipped galvanised iron, Isolating valves and non return valves

on suction & delivery side of pumps.

d) Common fabricated base frame, duly painted.

e) Power and control cabling between panel and pumps.

f) Accessories like presure guages, pressure switches etc.

g) Electric control panel mounted on the skid for automatic operation of

pumps comprising incoming switch fuse unit/MCBB, digital voltmeter &

ammeter with selector switches, over load and under voltage protection

devices, single phase preventors, MCB and DOL starter for each pump,

indicating lights etc. all complete.

Programmable Control System shall be PLC based, duly authentiated by the

Pump Manufacturer.

Notes: 1) Switchgear and starter ratings are indicative. The Tenderer shall

quote for the actual rating required as per the pump model proposed by him.

2) Provision for BMS connectivity. The panel should have sufficient no. of

potential free contacts for connectivity with Building Management System for

monitoring purposes

SUMP DRAINAGE PUMPS

AR on MR Supply, installing, testing and commissioning drainage pumping system in the ramp

332 base sump of plant room & STP plant room S-1 & S-2 comprising of the following:

a) 2 Nos.Vertical fully floodable type submersible drainage pumps in close

coupled design single stage, suitable for handling minimum 12 mm dia solids.

Discharge of each pump : 150 LPM

Working Head : 14 M

Material of Construction (M.O.C):

Corrosion Resistant in general

: Bearings — Anti friction,

prelubricated ball bearings,

packed with grease for life.

Motor: — Dry Motor with built in over

load protection

Protection - IP68.

Efficiency - IE2 Min.

Insulation Class - F

b) Electric control panel for automatic operation of pumps as per the water

level in the sump.The pump operation shall be controlled with magnetic float

type level controller.The Panel shall comprise of incoming MCB, digital

voltmeter & ammeter, On-Off lamps, starters with circuit breakers for each

pump, rotating start sequence, both pumps to work simultaneously to meet

There shall be an audio-visual alarm, if any pump fails to start.

c) Power cabling and control cabling between magnetic float type controller

panel and pump panels including cable tray as required.

d) Each pump should be skid base mounted of 9" height to avoid mud choking.

e) Pump suspension systemwith Stainless Steel Sling wire with `U` clamp.

f) HDPE Flexible Reinforced Hose with both side matching jubilee clamp for

ease of connection and disconnection from discharge pipe. Hose shall 3000

mm in length (Approximate). Hose size shall not be less than 50 mm dia.

AR on MR Supply, installing, testing and commissioning drainage pumping system in the ramp

base sump of Basement Parking S-4 comprising of the following:

a) 2 Nos.Vertical fully floodable type submersible drainage pumps in close

coupled design single stage, suitable for handling minimum 12 mm dia solids.

Discharge of each pump : 300 LPM

Working Head : 14 M

Material of Construction (M.O.C):

: Bearings — Anti friction,

Motor: — Dry Motor with built in over

Protection - IP68.

Efficiency - IE2 Min.

Insulation Class - F

b) Electric control panel for automatic operation of pumps as per the water

level in the sump.The pump operation shall be controlled with magnetic float

type level controller.The Panel shall comprise of incoming MCB, digital

voltmeter & ammeter, On-Off lamps, starters with circuit breakers for each

pump, rotating start sequence, both pumps to work simultaneously to meet

There shall be an audio-visual alarm, if any pump fails to start.

c) Power cabling and control cabling between magnetic float type controller

panel and pump panels including cable tray as required.

d) Each pump should be skid base mounted of 9" height to avoid mud choking.

e) Pump suspension systemwith Stainless Steel Sling wire with `U` clamp.

f) HDPE Flexible Reinforced Hose with both side matching jubilee clamp for

ease of connection and disconnection from discharge pipe. Hose shall 3000

mm in length (Approximate). Hose size shall not be less than 50 mm dia.

AR on MR Supply, installing, testing and commissioning drainage pumping system in the sump

of basement drainage S-3 & S-5 comprising of the following:

a) 2 Nos.Vertical fully floodable type submersible drainage pumps in close

coupled design single stage, suitable for handling minimum 12 mm dia solids.

Discharge of each pump : 100 LPM

Working Head : 14 M

Material of Construction (M.O.C):

: Bearings — Anti friction,

Motor: — Dry Motor with built in over

Protection - IP68.

Efficiency - IE2 Min.

Insulation Class - F

b) Electric control panel for automatic operation of pumps as per the water

c) Power cabling and control cabling between magnetic float type controller

d) Each pump should be skid base mounted of 9" height to avoid mud choking.

e) Pump suspension systemwith Stainless Steel Sling wire with `U` clamp.

f) HDPE Flexible Reinforced Hose with both side matching jubilee clamp for Set 2.00 180000.00 0.00 360000.00

LANDSCAPE IRRIGATION PUMPS

AR on MR Supply, installing, testing and commissioning of packaged pumping system for

treated effluent supply (For Landscape Irrigation) as per following details:

The packaged unit shall be complete with :

a) Pump & Motor:

RPM : 2900 RPM;

Power Supply: 3Ph 415V 50Hz

Insulation: Class - F

Motor Efficiency: Min. IE2

Protection:- IP54 Min.

Material of Construction (M.O.C):

: Impeller — Stainless Steel

: Shaft — Stainless Steel

Nos.: 2 nos. (1 working + 1 standby)

Discharge (each pump) : 7 M3/Hour

b) Pressure Tank: FRP vessel with replacable polyetheruethane (PEU) bladder

certified for drinking water. Minimum 10 Bar pressure rating — 2 No. 150 Lts.

c) Electric control panel mounted on the skid for automatic operation of pumps

comprising incoming switch fuse unit/ MCBB, digital voltmeter & ammeter with

selector switches, over load and under voltage protection devices, single phase

preventors, MCB and DOL starter for each pump, indicating lights etc, dry suction

cutoff, all complete.

d) Sequential Control System for the following logic:

i) System to start manually/automatically

ii) System stops automatically if the cut out pressure is achieved

iii) At every start, the other pump shall cut in

the idea is to keep both the pumps operational but with one remaining standby at

any particular moment.

There shall be audio visual alarm in case any pump fails to starts.

e) Interconnecting Pipe work and Valves : Common suction & delivery

headers in PVC Schedule 80 pipes conforming to ASTM-D 1785 and fittings

conforming to ASTM-D 2467, Isolating valves, non return valves on suction &

delivery side of pumps, Accessories like presure guages, pressure switches

f) Common fabricated base frame, duly painted.

g) Power and control cabling between panel and pumps. Set 1.00 475000.00 0.00 475000.00

Notes: 1) Switchgear and starter ratings are indicative. The Tenderer shall

quote for the actual rating required as per the pump model proposed by him.

WATER TREATMENT PLANT

AR on MR Collecting water sample(s) in a manner as perscribed by the laboratory, making

arrangement for the delivery of the sample(s) to the laboratory and getting the

336 sample(s) tested as per IS:10500 - Drinking Water Standard (complete physical, Job 3.00 10000.00 0.00 30000.00

chemical and micro-biological test) and submitting the report(s) to the Engineer-in-

AR on MR Providing, installing, testing and commissioning vertical down flow type multi grade

sand bed pressure filter capable of filtering 8 cum/hour of water at prescribed

filteration rate of 15 cum/sq.m/hr. The filter shall comprise of Composite FRP PP

lined shell, suitable for a minimum operating pressure of 5 kg/sq.cm. , complete with

pedestal, access cover, PVC underbed, 50 mm dia frontal piping, butterfly valve,

pressure guage, first charge of filter media. etc.

Details of Filter

Filter Shell MOC : Fibre glass and

polyester resin

Height : 1800 MM

AR on MR Providing, installing, testing and commissioning chlorine doser comprising 100 litres

capacity chemical grade polypropylene storage tank, electronic metering pump of 0 -

5 litres/hr. capacity against the minimum line pressure of 3 kg/cm2 , injection fitting,

solution delivery tube etc. including making electrical connection including

synchronisation for auto operation with raw water feed pump, all complete.

AR on MR Supplying, installing, testing and commissioning of Horizontal monoblock booster

pumpsets as per following details:

The pump unit shall be complete with :

a) Pumps: Horizontal monoblock booster pumpset with mechanical seal

a) Raw Water Feed Pumps

Discharge : 8 M3/Hr

Material of Construction (M.O.C):

: Impeller — Stainless Steel

: Shaft — Stainless Steel

Motor: 2900 RPM; 3Ph 415V 50Hz

Insulation Class - B Min

Efficiency - IE2 Min.

Protection - IP44 Min.

AR on MR Supply, installation, testing and commissioning of electric pump control panel metal

clad cubicle type suitable for 230V AC single phase 50Hz supply system. The panel

shall be completely compartmentalised and complete with relays, contactors,

starters, sequential pump controller, Bus Bars, designation labels as per

requirement, continuous earth bar, panel separators, protective screens, cable

clamping support system, top/bottom cable gland plates for incoming and out going

cable entries as per details given below:

Sequential pump controller is to keep both pumps operational but with one remaining

standby at any particular moment.

Note: The start stops operation of the pumps shall be controled with magnetic

float type level sensors in the treated water tank. The control cabling between

sensors and the panel will be paid separately as per the actual measurement

under a separate item.

There shall be an audio visual alarm in case any pump fails to start.

32A FP 10 KA MCB - 1 No.

A set of 63 A 415V 50Hz 3 Phase four wire copper busbars.

INSTRUMENTS FOR INCOMER

— Ammeter 0-32A with Selector Switch

( including a set of CTs 32/5A)

— Voltmeter 0-500V with selector switch.

— A set of phase indicating light with

INSTRUMENTS ON OUTGOINGS

— Ammeter with selector switch for each

— Indication lights for ON-OFF-TRIP indication for each pump

Selector switch for auto/manual mode selection for the pumping system

OUTGOING FEEDERS

20A 10KA TP MCB 2.0HP DOL starter, overload relay, single phase preventer, timer Set 1.00 60000.00 0.00 60000.00

etc. - 2 Nos. Dry run protection with sensor complete as required.

16A 10KA DP MCB - 2 Nos.

Note: Switchgear and starter ratings are indicative. The Tenderer shall quote

for the actual rating required as per the pump model proposed by him.

CABLING AND MAIN PANEL

AR on MR Supplying and fixing of following types and sizes of 1.1 KV grade PVC insulated

conductor armoured cable conforming to IS : 1554.

a) 3C 2.5 sq.mm. Copper conductor M 50.00 240.00 0.00 12000.00

b) 4C 4 sq.mm. Copper conductor M 30.00 400.00 0.00 12000.00

AR on MR Supplying, laying & terminating of following types and size of 1.1 KV grade PVC

isulated armoured control cables conforming to IS : 1554 Part-II

AR on MR Supplying and making end termination with brass double compression glands and

copper/aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE

copper/aluminium conductor cable of 1.1 KV grade as required :

a) 3C 2.5 sq.mm. Copper conductor Set 4.00 125.00 0.00 500.00

b) 4C 4 sq.mm. Copper conductor Set 2.00 250.00 0.00 500.00

c) 4C 16 sq.mm. `Al' conductor Set 12.00 330.00 0.00 3960.00

AR on MR Providing and fixing following size G.I. strip / wire on surface or in recess for body