SPECIAL REPAIR TO P-9 BUILDING 8 GROUND and FIRST FLOOR OF QAE (NAVAL) AND P-14 BUILDING AT DGQA COMPLEX BADARPUR UNDER GE (AF) TUGHLAKABAD

Amount

Taking down chowkats or frame with shutter (without taking out shutter from the frame) exceeding 1.50 sqm and n exc 4.00 sqm each and removal from site all as specified and directed.

Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each and removal from site all as specified and directed

Taking down or up 15 mm bore galvanised iron tubing and connection including cleaning for refixing or removal all as specified

All as per item No 3 here in before but 20 mm bore

Taking down cement plaster including raking out joints hacking for key and scrubbing down with water complete as specified and directed. All dismantling/demolished material removed from MOD land completely

Taking down rain water pipe and eaves gutters (any size and pattern) including all fittings heads shoes bends swan necks etc complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving n exc 15 cm thickness (below or above ground level)

Demolition of cement concrete of any description & in any position not otherwise specially provided for etc complete all as specified & directed.

Dismantling of cast iron drain pipe of 100mm bore jointed in lead joints or cement joints and taking out of under floors if required

Demolition of brick work or stone/boulder masonry, built in cement mortar incl. all quoins arches, pillars etc. but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

S&F 1000 ltrs Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top ) including dismantling and hoisted and fixed in position etc complete all as per specified and directed.

S & F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified.

All as per serial item 12 here in before but 20 mm bore

Refixing only old GI tubing 15 mm bore pipe and connections in new or old position as on walls ceiling floors etc all as specified. (i) Cleaning of pipe is included in Srl No 03 & 04 here in before (ii) Rates quoted by the contractor deemed to be included S & F new fittings as required.

All as per serial item 14 here in before but 20 mm bore

S & F in repair 20 mm bore ball brass valves (Float valve) high pressure with polythene float and fly nut complete screwed to iron pipe or brass ferrule complete all as specified

S & F in repair 20 mm bore Gun-metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe all as specified and as directed

S & F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm pre-laminate PVC sheet, reinforced with MS square tube fixed in opening with smooth finish complete as per manufacturer's specifications and as directed by Engineer-in-Charge

S & F factory Made Solid PVC Moulded Door Shutter with particle board, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded pre-laminated PVC Sheet on the front face & 2mm colour PVC pre-laminated sheet on back face, supplying & fixing in frame at site as per specification & drawing specified in SSR and as directed by Engineer-in-Charge

S&F 100 mm long butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type C-21

S&F 150 mm size aluminium handles, cast type anodised and fixed.

S&F 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/ Chowkhat of size 100 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

M & L for PCC 1:2:4 type B1 in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles complete as per direction of Engineer-in-Charge.

M &L WPC Flush shutters,30mm thick solid core construction, with block board core and plywood face panels, commercial type on one sides with 0.9mm thick decorative laminate type 1 on both side and lipping/frame to match surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer’s instructions.

S & F 200 mm mild steel barrel tower bolts stove enamelled black with bright bolt and fixed

S & F SS finish mortise lock handle set 175mm size with 6 lever locking mechanism all as spfd and directed

S & F 100 mm size mild steel butt hinges medium weight cold rolled and fixed with screws or welding where required

S & F mild steel pressed handle 150 mm long oval types stove enamelled black

S&F floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring overall length 140mm complete all as specified and as directed.

S&F Aluminium Anodized powder coated aluminium frame for doors, windows, ventilators, partition wall with one or more rebates including joining cleat for fixing etc complete all as specified. (thickness of powder coating is 50 micron)

S&F anodised aluminium powder coating of any colour (Thickness of powder coating not less than 50 micron) window and ventilator shutter side hung type suitable for glass pan without sash bar, aluminium sections weighing 0.55kg/m incl necessary joining cleat glazing clips, rubber neoprene packing, aluminium anodised snap beading, screws , peg stay 150mm long -1 No, hinges type B-21 100mm long -2 Nos, suitable handle -1 No complete all as specified handles 1 Nos in each window, hinges, aluminium snap beading screws complete all as specified.

S&F anodised aluminium powder coating of any colour (Thickness of powder coating not less than 50 micron) window and ventilator shutter side hung type suitable for wire mesh without sash bar, aluminium sections weighing 0.55kg/m incl necessary joining cleat glazing clips, rubber neoprene packing, aluminium anodised snap beading, screws, peg stay 150mm long -1 No, hinges type B-21 100mm long -2 Nos, suitable handle -1 No complete all as specified handles 2 Nos in each window, hinges, aluminium snap beading screws complete all as specified.

Supply and fixing 7mm thick aluminium grill of make Deco grill DG-104 model fitted in to suitable aluminium channel and fixed to windows/ventilators including channel complete all as directed by Engr-in-charge.

S&F 4.0 mm thick plain sheet glass panes and glazing with oil putty in square not exceeding 0.5 Sqm in each pane and fix in aluminium door / window/ventilator complete all as specified.

S&F 4.0 mm thick Figured glass, pin head type and glazing with aluminium beading screws or oil putty in square not exceeding 0.5 sqm in each pane and fix in aluminium door/ window/ ventilator complete all as specified.

S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and fixed with tinned tacks or galvanised wire staple complete all as specified.

M&L for providing and applying corrosion resistance non-shrink free flow, cementitious one component Micro-concrete with average thickness 75mm having compressive strength (BS 4551-80-60) 50 MPA at 28 days, Tensile strength (ASTM C 348)-2.0 N/mm2 @ 28 days, Flexural strength (ASTM C 348)-9 epoxy bonding agent TM bond EP thermax having mix density of 1.45 to 1.5 kg/ltr, compressive strength (BS-6319 PT 3)-25 Mpa at 7 days bond strength (ASTM C 881)- 11 N/mm2 at 7 days, having an over lay time of 3 hrs at 30°C pouring of micro concrete into the formwork using suitable arrangement or if required using pumping device for and the bottom shuttering after 7 days ensuring proper bond between the micro concrete and existing concrete substrate etc including all tools and tackles as per accepting office, complete all as specified and directed by Engineer-in-Charge. Make : BS-66 Music of Thermax/Webac Chemicals/Chemco System or as approved by Accepting Officer. Note: Shuttering & Scaffolding rate deemed to include in same item. Height of building upto 4 mtr. No extra claim by contractor for same.

M & L for washed stone grit plaster on exterior walls in two layers, under layer 15 mm thick cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool ,applying cement slurry on the under layer @ 3 kg of cement per sqm, top layer 15 mm thick cement plaster 1:1/2:2 (1 white cement : 1/2 coarse sand : 2 stone chipping 8 to 10 mm nominal size ) in panels with aluminium beading groove ( size of aluminium beading 10 mmx 10 mm ) all around as per approved pattern including scrubbing and washing and colour (as per user direction ) the top layer with brushes and water to expose the stone chippings complete all as specified and directed by Engr-in-charge. Note : work can carried out upto 15 mtr height.

M&L for 15mm thick rendering in CM 1:6 on other than fair faces of brick or concrete surfaces finished even and smooth without using extra cement all as spfd and directed.

M & L for 75 mm thick PCC 1:3:6 type C2 as in plinth protection finished even and smooth without using extra cement as specified

M&L for construction joint 30mm deep x 10mm wide with sealing compound grade 'B' all as spfd and directed

S&F in repairs of Venetian blinds, vertical type, 100 mm wide with polyester fabric of approved colour and pattern with aluminium fittings, and top rail and nylon buttons/loops etc fixed cuttings and alteration if necessary where ever AC/ coolers exists complete all as specified and directed by Engr-in-charge.

S&F in repair PVC wall lining joint free consisting of 5mm thick colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification. Note : Cost of Cornices, Fillets included in same item. Pattern/design and colour shall be approved by Accepting Officer. No Extra shall claim by the contractor for same.

S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing.

M&L for 4 mm thick acrylic colour sheet exc 0.50 sqm in each pane & fixed by drilling holes/punching/screwing fixed with beads with metal panel pins/spring clips in metal surrounds including taking down old glass/sheet with putty. Work to be carried out up to 16m height.

S & F 110 mm bore of pipe PVC (SWR) pipes double socket in any length with rubber ring joint laid in trenches on in floor as directed

All as per item No 47 here in before but fixed to walls

S & F 75 mm bore of pipe PVC (SWR) pipes double socket in any length with rubber ring joint laid in trenches on in floor as directed

S & PVC (SWR) floor trap 75mm dia, plain with CP grating including jointing with solvent jointing to waste pipe with cement joints etc complete as directed

S & PVC (SWR) floor trap 100mm dia, plain with CP grating including jointing with solvent jointing to waste pipe with cement joints etc complete as directed

S & F 110 mm bore PVC(SWR) bend of any radius diminshing pieces or tappers (larger bore measured) fitted with access door complete all as specified and directed

S&F in repair of PVC (SWR) branch pieces, tee equal or unequal spigot or socket type or with parallel branches to 110 mm dia pipe fitted with access door complete all as specified by Engineer-in -Charge.

S&F in repair vitreous china wash basin under counter oval type (536mm X 435 mm), white, flat back, size 550 mm x 400 mm fixed over granite and including CP waste coupling, waste fitting and union complete all as specified and as directed.

S&F in repair vitreous china wash basin, flat, back, size 650x400 x 200) mm including full pedestal but including brackets and including cutting for and pinioning in ends of brackets, waste pipe, coupling and pillar tap complete fittings all as directed by Engr-in-Charge

S&F in repair swan neck pillar mixer cast copper alloy for iron pipe and fixed with 15mm bore in repairs all as directed.

S&F 32 mm bore of pipe low density (LDPE) of pressure rating 6 kg/ Sqcm fixed to wall or floor etc including fittings complete all as specified and as directed.

S&F 32mm dia waste fitting brass chromium plated for basin with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S&F in repair vitreous ceramic full stall urinal with SS urinal spreader, coupling & waste pipe complete in all respected as directed.

S&F in repair Curved Urinal Partition with frosted glass 8mm thickness and size (900mm, H x 450mm, W) all as directed

S & F in repair PVC connection 15 mm size with CP nuts of length 600 mm etc complete all as specified.

S&F bib tap of CP fancy type with butterfly handle screwed down screwed for iron pipe of 15mm bore fixed in repairs

S&F in repairs 2 way angle cock double handle with flange 15 mm bore (for iron pipe) cast copper alloy fancy type chromium plated screwed down, complete all as specified and as directed by Engr-in-charge .

S&F in repair angle valves CP screwed down high pressure of fancy type chromium plated screwed both ends for iron pipe or for union and fixed with 15mm bore complete all as specified.

S&F in repair of CP soap tray fixed to walls with rubber plugs complete all as specified and directed.

S&F in repair of Wall mixture 15mm bore dia cast copper alloy with cap capstan chromium plated screwed down high pressure with or without lettered "Hot" or "Cold" with long screwed shanks and fly buts screwed for iron pipe complete all as specified and as directed

S & F in repair of 15 mm dia bore concealed stop valves cast copper alloy chromium plated fancy type with long shank & cup (concealed type) complete all as specified and as directed.

S&F in repair brass chromium plated tubular towel rail 20 mm dia D type, 60 cm long between flanges complete all as specified and as directed.

S&F in repair sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F of wall mounted LED mirror with smart sensor and 3 colour (warm, white, Natural) (600mm x 450mm) fixed as per manufacturer's spfd complete all as directed

S&F in repair of PVC bath room cabinet with mirror of size 432 mm x 311 mm complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan with cistern (wall mounted closet) including flushing cistern and flush pipe) including connection to drain or outgoing pipe and flush pipe with complete fittings all as specified and as directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts flushing cistern and flush pipe) with seat cover with CP screw complete all as specified and as directed.

S & F in repair PVC low level cistern of 10 lit capacity inclusive of brackets and PVC bend long type and connection to flush pipe of any size and pattern with inlet ball valve float and handle etc. complete all as specified & directed.

S&F in repair A Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S & F 110 mm bore of pipe PVC (SWR) pipes double socket in any length with rubber ring joint fixed to walls with MS clamps as directed

S & F 110 mm bore of pipe PVC (SWR) bends with access door of any radius / shoe fixed to PVC pipes as directed

M&L for GVT (Glazed vitrified tile) tiles light coloured of size 300x600mm and thickness more than 9mm, on vertical surfaces such as skirting/dados etc, set & jointed in high performance polymer based adhesive (Laticrete Plus or equivalent) & pointed in coloured cement to match the shade of tiles over rendering 15 mm thick in CM (1:4) on wall including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) all as specified and directed by the Engr-in-Charge. All dismantled/demolished material shall be removed from MoD land and not extra claim by contractor for same.

M&L for Vitrified Ceramic tiles 10mm thick(square/rectangular) polished, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors over 15 mm thick screed bed in CM (1:6) etc set and jointing in neat cement slurry and pointed in white or coloured cement to match, including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) all as specified and directed by the Engr-in-Charge. All dismantled/demolished material shall be removed from MoD land and not extra claim by contractor for same.

S&F non skid ceramic coloured tiles of 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm in floor with 15 mm thick Screed bed or bedding layer in CM (1:6) set and jointed in neat cement slurry and pointed with white or coloured cement to match including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) all as specified and directed by the Engr-in-Charge. All dismantled/demolished material shall be removed from MoD land and not extra claim by contractor for same.

Material & labour for dura stone (HDVT) 12mm thick heavy duty outdoor tiles, rustic finish of size 600x600mm in floors etc set & jointed in high performance polymer based adhesive (laticrete 315 Plus of equivalent ) to be mixed with water or latex with spacer and grout fill with MYK LATICRETE Stellar grout OR MYK LATICRETE Sanded or Unsanded Grout mixed with MYK LATICRETE 1776 Grout Admix Plus or equivalent complete all as specified and directed incl dismantling floor, hearth or wall tiling including cement mortar bedding cement mortar bedding (but not backing ) all as spfd and directed. All dismantling/demolished material removed from MOD land completely. Rate of removal outside side from MoD land deemed to be included in the same item.

M&L brick work in CM (1:6) with sub class ‘B’ bricks straight or curved on plane exc 6m mean readies, used in drain, boundary wall, compound wall complete all as specified and directed by Engr in charge.

M&L for 20mm thick granite (of any type)work (table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms and like over 15mm thick screed bed in CM 1:6 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite etc complete all as specified.

Rounding to the edge of stone slabs on edge such as cooking platform

S&F heavy duty parking tile (300x300mm) and 30mm thick Pre Polished sleek glossy look, water repellence over 15mm thick screed bed of CM1:4 all as spfd and directed by Engr-in-Charge

S&F in repair of corner glass shelf 12" complete all as specified and as directed.

S&F in repair of front glass shelf 450 mm long complete all as specified and as directed.

Dismantling boarding, any description, any description, fixed in any position with nails etc complete all as specified & directed.

S& F 18 mm solid PVC ply of 1st quality of approved colour laminate one side and white another side fixed with 'L' SS button fixed with screw as a shelf complete all as specified and directed by Engineer-in-charge.

S&F 18 mm solid PVC ply of 1st quality of both side prelaminated colour fixed as a shutter with screw, solvent cement/adhesive complete all as specified and directed by Engineer-in-charge.

S & F Brass 4 lever locks, cupboard, grade I, size 50 mm

S&F Magnetic catcher for Wardrobe, Cub-boards Etc.

S&F SS hydraulic soft close hinge with screws for door shutter of cabinet all as directed.

Supply and fixing stainless steel fancy Grade 304 handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.

Dismantling of wrought iron or Mild Steel work of any description complete all as specified and directed by EIC

S&F framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

S&F in repair Aluminium door seal width of 1.50 inch with nylon brush fitted with screw complete all as specified and as directed.

M&L for racking out joints/pointing of cement mortar to brick tile work laid flat in roof all as spfd and directed

M&L for flush pointing with CM 1:3 to brick laid flat or brick tile on roof all as spfd and directed

M&L for nominal mix of cement concrete Type B0(1:11/2:3) using 12.5mm graded aggregate as in roof for maint the uniform slope all as directed by Engr-in-Charge

M&L for 10mm thick plastering in CM (1:3) on green concrete roof surfaces Sqm with water proofing compound @ 3% by weight of cement, surface finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge. Note - WPC shall be measured and paid separately.

Supply only integral water proofing compound ISI Marked complete all as specified and directed by Engr-in-charge.

M & L for rendering 5 mm thick on ceiling on fair faces of brick or concrete surface in CM (1:3) finished even and smooth without using extra cement all as specified

M & L for preparation of new plastered surfaces of walls and applying two coat of Oil Bound distemper over a coat of 1mm thick wall care putty on wall, complete all as specified.

M&L for preparation of new plastered surface of walls and applying two coat of exterior weather proof water base emulsion paint (APEX) of any colour complete all as specified & directed. Note:- Quoted rate shall be deemed to be included for work in buildings/structure upto 10mtr height.

M&L for complete removal of old existing treatment of walls surfaces and applying a coat of white cement base wall care putty in patches as required and as directed by Engr-in-Charge finished even and smooth with sand paper and applying two coat of exterior weather proof water base emulsion paint (APEX) of any colour all as specified & directed. Note:- Quoted rate shall be deemed to be included for work in buildings/structure upto 15 mtr height.

M & L preparation of newly plastered surfaces and applying three coat of white wash on ceiling incl preparation of surfaces.

M&L for preparation of old surfaces including complete removal of old existing treatment of wall surfaces and applying two coat of Oil Bound distemper over a coat of 1mm thick wall care putty on wall,

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of primer etc. complete all as specified and as directed.

M & L preparation of new surfaces of steel and iron work of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of primer etc complete all as specified and as directed.

M&L for preparation of old painted wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint etc complete all as specified and as directed.

M & L preparation of old painted surface of steel and iron work of any description over 10 cm width or girth and applying one coat of synthetic enamel paint etc complete all as specified and as directed.

Demolition of concrete is reinforced (Reinforcement cut as required to facilitate demolition) of any description and in any position not other wise specially provided for complete all as specified and directed by Engineer in Charge

S&F 30 mm thick factory made WPC glazed and skeleton shutters, open rebated and with SS wire gauze dia 0.63mm and average width of aperture 1.4mm in both side (Top rail 100mmx30mm, Lock Rail 150mmx30mm & bottom rail 150mmx30mm) and stylise (150mmx30mm) complete with laminate finishing. Lipping/frame to match surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions.

S & F 300 mm mild steel sliding bolt plate type stove enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate and fixed

M&L TMT steel bars 10mm dia and over cut to length bent shape required, including cranking bending binding with mild steel wire (annealed) not less than 0.9mm dia quality conforming to relevant IS complete all as specified.

M&L demolition of old existing loose/unsound weaken mixture of binding material such as cement and fine aggregate(<4.5mm retained on IS sieve) of any description and in any position from existing internal surface of RC components or any surface having average profundity of 15mm by hand tool that has a long metal blade with a sharp edge at end chisel and hammer or user robust pneumatic chisel/hand tools and removal from MoD land including M&L for applying one coat of mixture of two monomer unsaturated liquid hydrocarbon and gaseous hydrocarbon and polymerized them to get the high polymer dispersion emulsion can be successfully bond to cement mortar , which improved adhesion to concrete, offers the better durability, reduces the shrinkage and increase the flexibility and resistant to emulsification in damp condition modified. Ensuring no porosity in new/old surface on dilapidated girders or reinforcement encased in concrete complete all as specified and directed by Engr-in-Charge.

M&L for applying hydraulic binders, osmotic and complexing admixture passivation additives passivating protective matrix and welded MS wire cloth weigh not less than 1Kg/Sqm with 20mm thick one component chloride free shear thinning fibre reinforced polymer modified, additives reduce or eliminate internal rust and corrosion by neutralizing acids and forming a chemical protective barrier to repel moisture from metal surface corrosion inhibiting additive, primer MUCIS for exposed corroded visible steel forming a continuous film not less than 250 micron of single component conforming to EN 1504-7-2006 and preparing the surface to receive the bled of epoxy and sand including providing necessary proportions complete all as spfd and directed by Engr in charge. Make : Thermax, M/s Sika India Ltd , M/s STP Ltd

M&L for 10mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces finished even and smooth without using extra cement all as spfd and directed.

S&F in repair 15mm dia bore cast copper alloy fancy swan neck type mixer pillar tape for cold and hot water complete all as spfd and directed

S&F in repair of brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and as directed

S&F in repairs stainless steel curtain rod of dia 25 mm complete as approved.

S&F Stainless steel bracket with finels for holding curtain rods of dia 25 mm as approved

S&F in repair grating doom 100 mm dia SS Grade 304 all as specified and directed by Engr-in-Charge

S&F of glazed ceramic coloured tiles 7mm thick 450 x 300mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade etc including 10 mm thick rendering in CM 1:4 including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L Non-skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors over 15 mm thick screed bed in CM (1:6) etc set and jointing in neat cement slurry and pointed in white or coloured cement to match, including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M & L for Rolled Steel section (Fe -410, Grade E-250)as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws to steel frame work incl dismantling of plain or corrugated steel galvalume sheet/valley gutter any gauge, thickness including nainital or similar pattern roof coverings including ridges for north light truss, as specified.

S&F 18 mm solid PVC ply of 1st quality of approved colour one side and white another side fixed with 'L' SS button fixed with screw including fixing 2mm thick PVC edge banding tape with hot glue by edge banding machine as a shelf complete all as specified and directed by Engineer-in-charge.

S& F 18/19 mm solid PVC ply of 1st quality of both side prelaminated colour fixed as a shutter including fixing 2mm thick PVC edge banding tape with hot glue by edge banding machine etc with necessary auto closing spring loaded hinges (hydraulic type) etc complete as per direction with screw, solvent cement/ adhesive complete all as specified and directed by Engineer-in-charge.

Complete taking down/demolition carefully any type of existing roof treatment i.e. mud puska, brick coba, brick tiles, any type of tiles, PCC, plastering, leeping etc. of any type and thickness varying from 20mm to 125mm in roofs including cleaning the surface after removal (removing the rubbish) complete all as specified and as directed. Note:- Rate of removal of debris outside from MoD land deemed to be included in the same item.

Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and slurry 1:3 complete all as specified and as directed.

M&L for nominal mix of cement concrete Type A0 (1:11/2:3) using 12.5mm graded aggregate as in roof for maint the uniform slope all as directed by Engr-in-Charge

Surface preparation and applying cement screed bed of 10 mm thick 1:4 with water proofing compound @ 3% weight of cement as per manufacture instruction with APP modified polymeric membrane centre core of 100 micron HMHDPE, weight not less than 3 Kg/Sqm and clear thickness of membrane not less than 3 mm thickness, on newly prepared surface with overlap while torching shall be 100mm on length side & 100mm on width side of membrane as per manufacturer instruction complete all as specified and as directed with the following description. (a) Apply evenly a coat of bituminous primer conforming to IS -3384 @ 0.40Kg/Sqm. (b) A coat of bonding bitumen confirming to IS -702 of grade 85/25 @1.20Kg/Sqm as IInd course. (c) Laying of APP modified polymeric membrane as a IIIrd course. (d) Two coat of aluminium paint and application by brushing @.25 Kg/sqm on APP membrane as a forth course.

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner all as spfd and directed by Engr-in-charge.

Taking down carefully aluminium point wiring (light/fan/socket power) complete, including fixture and fitting such as switches, ceiling roses, pendants, regulators, socket, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition separately) and making good disturbed surfaces of walls, floors, etc.

Material and labour for point wiring concealed in and including rigid non-metallic PVC conduit, medium grade, ISI marked, 19/20 mm dia, with 1.5 sq mm FRLS PVC insulated & unsheathed, multi stranded copper conductor cable, single core, 1100 volts grade, with modular flush metal terminal boxes factory fabricated (same make of modular type switches and sockets (etc.) modular metal box including cover plates, frames of suitable size and depth including FRLS insulated and unsheathed Multi standared copper conductor of 1.5 sqmm and connected to common earth dolly as continuous earth wire complete for the following :- (Note cutting chases and making good with two coat white wash incl matching with existing surfaces in included in quoted rate by the contractor).

One light/fan/ bell point controlled by one modular switch one way

One 3/5 pin socket outlet point on the same board with other modular switches

One 5 Amp socket outlet modular point on independent board with one modular switch one way.

All as per item No 138 here in before but Power point 15 Amps wiring using 2.5 sqmm copper conductor unsheathed cable with earth wire 2.5 sq. mm green PVC insulated. Complete all as specified and directed by Engr-in-Charge.

Taking down existing sub main wiring of any type and description including removal of teak wood batten/pipe etc complete.

M&L sub main wiring with multistranded FRLS copper conductor cable PVC sheathed in and including concealed in brick wall/RCC as per the site condition, providing suitable PVC conduit with three runs of 6.0 Sqmm and 6.0 Sqmm FRLS copper conductor as earth wire and connected to earth dolly all as specified and as directed by Engr-in-Charge. (The work includes cutting of Chasis and making good the disturbed surfaces)

All as per item No 144 here in before but sub main wiring of three run 4 sqmm complete all as specified and directed.

M&L for modular socket outlet 6A, 2/3 pin combined 2 module complete all as specified and as directed by EIC.

M&L for modular socket outlet 6A/16A, 2/3 pin combined 2 module complete all as specified and as directed by EIC.

M&L for modular switch 1 way 6 Amps 1 module, suitable for 230 Volts AC supply complete all as specified and as directed.

M&L for modular switch 1 way 15/16 Amps 1 module, suitable for 230 Volts Ac supply complete all as specified and as directed by EIC.

M&L ceiling rose 3 terminal 230 volt all as specified and directed by Engr-in Charge

M&L for Electronic modular fan regulator step type 120 watts 2 module complete all as specified and directed by Engineer-in-Charge.

S&F Modular Bell push switch 6 A 1 module all as specified and directed by Engineer-in-Charge.

S&F Multi purpose Bell suitable for AC, 230 Volts, 50 Hz complete all as directed by Engineer-in-charge.

Taking down old UNSV socket DB, M&L for metal clad plug & socket with earth complete with metal clad plug top and including one single pole including MCB 32 Amps 240 volts complete all as specified and directed by Engr-in-charge.

Taking down old UNSV DB, S&F sheet metal enclosure for flush with wall DB's when MCBs to be used single pole & neutral 8 way single door 240V complete all as directed by Engr-in-Charge.

Taking down old UNSV MCB from DB, S&F of TP&N 4 Pole, 4 ways vertical load line flush with wall DB are fitted with bus bars, neutral 4 way double door 415 volts complete all as specified and directed by Eng-In-charge.

Taking down old UNSV MCCB from DB, S&F MCCB sheet metal enclosure distribution board fabricated with CRCA sheet steel, powder coated included with insulated vertical phase bus bar, neutral bars and earth bars, cement spill protector and colour coded interconnecting wire set, cable ties, blanking plates of double door type suitable for housed 3/4 pole MCCB as incomer and SP/TP MCBs as outgoing, IP 43, metal door type, TPN 12 way, complete with MCCB 4 pole, 415 Volts, fixed type, 125 Amps with breaking capacity 16 KA complete fixed to MCCB DB enclosure and DB to be fixed with walls concealed type including taking down old existing DB all as specified and directed.

Taking down old UNSV MCB from DB, M&L for MCB 'C' curve 6 to 32 Amps SP 10 KA load as per requirement of site, to incorporate in above DB complete all as specified and directed by Engr-in-charge.

Taking down old UNSV MCB, M& L for MCB DP C curve 40 Amps. Complete all as specified and directed by Engr-in-Charge.

Taking down old UNSV MCB, M& L for MCB Four pole higher rating MCB of 63 Amps capacity, 10 KA, 415 Volts complete incl taking out old UNSV from existing DB all as specified and directed by Engr-in-charge.

S&F wall mounted LED batten 20 watt, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver 230 Volt, incl all accessories prewired including making necessary electrical connection with 3 core copper conductor and testing complete all as directed by Engr-in-charge

S&F wall mounted LED batten 10 watt , extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver ,230 Volt, incl all accessories prewired including and making necessary electrical connection with 3 core copper conductor and testing complete all as directed by Engr-in-charge

S&F in repair surface/recess mounted LED flat panel 2'x2' with high efficient LEDs of capacity 34/36 W & glare free full window opal diffuser in replacement of existing light fitting complete all as specified & directed by Engr-in-Charge.

Supply and fix surface/recess mounted LED flat panel 1'x1' with high efficient LEDs of capacity 15 W & glare free full window opal diffuser in replacement of existing light fitting complete all as specified & directed by Engr-in-Charge.

Material and labour for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to GI strip 25x4 mm main earthing lead by means of galvanized bolts, nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I (2009) with connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt all around earth plate, test point of phosphorous bronze / gun metal of size 75 mmx 75 mm x25 mm, PCC (1:3:6) type C-1 (using 20mm graded black trap/granite/Basalt stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, pre cast RCC (1:2:4) type B-1 (using 20mm graded black trap/granite/Basalt stone aggregate) 40mm thick cover reinforced with 8mm dia TMT bars 3 Nos both way with 12mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh, and 25 mm dia GI medium grade earth lead protection pipe, complete all as specified and directed. NOTE : Earth wire and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item and additional earth strip/protection pipe etc. if any required at site shall be measured and paid for separately under appropriate item of Schedule `A’

S&F cable PVC insulated and sheathed flexible 3 core of size 2.5 sqmm with multistrand copper conductor of 1100 volts grade complete all as specified.

Taking down carefully AC single phase 220/230volt ceiling fan 1200/1400mm sweep single phase complete at site for rewinding and replacement of unserviceable parts i.e Capacitor, PVC connector, MS galvanised check nut, ball bearing, rubber pads, PVC strip clamps including servicing such as removing dust & dirt brushing, rubbing with cotton waste, , washing with detergent powder to fan blades, greasing bearing with ball bearing grease & washer packing, checking of bolts/nuts, washer check nuts split pin rubber packing and rubber seal etc including testing after assembling and connecting to electric system complete all as specified and as directed by Engr-in-Charge. Note : Rates of winding and replacement of any unserviceable parts mentioned above required to make the fan in serviceable condition are include in the quoted rate.

Taking out old UNSV louvers of any type upto G+1 storey, supply and fixing exhaust fan louver of size 300 / 450 mm sweep made out of MS sheet heavy duty of 22 gauge complete including making good the disturbed surface of wall both inner and outer side and match with the existing all as specified and directed. Make- As per sample

Taking out old UNSV UPVC pipe of 65 mm bore complete from existing system, M&L including testing and commissioning UPVC pipe 10 Kg/Cm2 pressure, ISI marked of 65/63mm bore (Outer dia)(As per site requirement) complete with all connected accessories/fittings like elbow, reducer, union, adapter and end plug etc complete all as specified and directed by EIC.

M&L for providing cement concrete type C1 (1:3:6) using 20mm graded trap stone aggregate for foundations/copping of pole/trenches in sub stn etc complete all as specified and directed by Engr-in-charge.

Taking down the old unserviceable exhaust fan from the existing position and Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers with all connected accessories and depositing old fan at AGE E/M store yard complete all as specified and directed by Engr-in-Charge.

M&L in replacement of wall fan of 450 mm sweep, 3 blade type, 1440 rpm, 80 watts with 3 speed rating suitable for AC supply, 230 volts, 50 Hz and deposit the old fan into AGE E/M store yard at Vayusenabad complete all as specified and directed by Engr-in-Charge.

Taking down old existing serviceable ceiling fan of 1200/1400 mm sweep carefully, sealing cable end, dismantling blades and removing the fan and blades and depositing the same to MES store as per the direction of the Engr-in-charge.

Fixing only Ceiling fan after complete cleaning of all dust and connecting up including provision of cable from ceiling rose or connector to fan all as directed by Engr-in-charge.

Taking down old existing serviceable exhaust fan of 250/300 mm sweep carefully , sealing cable end, dismantling band depositing the same to MES store as per direction of the Engr-in-Charge.

Fixing only Exhaust fan after complete cleaning of all dust and connecting up including provision of cable from ceiling rose or connector to fan all as directed by Engr-in-charge.

Deepak Electricals (BID ID -3504377)

Neeraj Enterprises (BID ID -3499224)

FUTURE ENGINEERING (BID ID -3503763)

GM2 (BID ID -3509441)

POOJA ENTERPRISES (BID ID -3509681)

M/S S.K.Electricals (BID ID -3504176)