Development of Park near Kala Niketan School Gazipur through installation of Children Play Apparatus Open Gyms and Sitting arrangement etc in W No 19E Shah South Zone

Amount

PART – ‘A’ ... Installation ofChildren Play Apparatus (CPA) :-

Supply and fixing of 1.8 MTR Wave Slide. "A" shaped support posts of height 2.28 m, are to be schedule Galvanized steel with a 60mm OD {Outer Diameter}. All the posts are to be finished with a baked on powder coat finish. Powder coatings used TGIC Polyester powder. Electro - statically applied polyester powder must have a tough finish with maximum durability. Deck of size 0.80 m x 0.60 m and Staircase of size 1.84 m x 0.60 m shall be an all-PATENT welded assembly fabricated from perforated solid punched steel. Deck perimeter is precision pre punched for attachments. Decks are pre pressed, punched, and welded, powder coated to 2.2mm thickness or vinyl plastic coated to a thickness of 4mm of height 1.9 m and Dia 32 mm shall be an all patent welded unit, fabricated from 32 0.D. galvanized steel pipes with a baked on powder coating finish. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. Wavey Slide of size 2.95 m x 0.72 m x 1.72 m, Panels, Plastic Components [super thick plastic] shall be rotationally molded from antistatic, copolymer. ALL WELDING IS CARRIED OUT BY ROBOTS [SIMMILIAR TO THE ONES USED IN THE AUTOMOBILE INDUSTRY], WHICH GUARANTEES STRONG AND SMOOTH WELDS ELIMINATING ANY RAG, WELD SCARS AND ENSURES THE INTEGRITY AND STRENGTH OF THE WELDED AREAS-PLAY EQUIPMENT DIMENSIONS: Size: L x W x H 4.18 m x 0.89 m x 2.28 m- All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:1%: 3 (1 cement : 11/2 coarse sand : 3 graded stone aggregate 20mm nominal size) of required size as per department/ manufacturers specifications and guidelines- (The fixing charges of C:C Block shall be paid Separately).

Supply and Fixing of Merry Go Round The platform Dia.1.21m, of thickness 2mm and width of 60 mm, with solid precision punched holes and reinforcement rib. After shot blasting, oil and phosphate removal, Zinc Primer Paint is applied at all the welding points using Zinc powder (Interpon PZ660) and Powder coated using Akzo Nobel powder coating.The handrails is made from Dia. 50 mm galvanized steel tubes and wall thickness of 2mm as per GB / T 700-1988. The welding used is C02 shielded arc welding (meets with the requirement of BS1387-1985, and the technology used meets the requirement of the BS1387-1985) and welding is done by robotic welding. The Centre rod for the merry go round is made from 98mm dia, galvanized steel post and connected on to a 160mm dia pipe which is connected to the base plate at the bottom for fixing the foundation. The concealed bearings of grade 6213 and 32213 which conforms to GB-T308-2002 is used to ensure smooth movement of the equipment. The centre rod is connected to the 1.3m dia platform througha base plate of 250mm dia using M16 stainless steel anti theft screws. The installation requires the poles to be fitted using Anchor fasteners on a concrete foundation of minimum strength M-25, cement concrete blocks of required size, as per direction given by engineer in charge, finished below ground level. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:1h: 3 (1 cement : Ih coarse sand : 3 graded stone aggregate 20mm nominal size) of required size as per department/ manufacturers specifications and guidelines. (The fixing charges of C:C Block shall be paid Separately).

Supply and fixing of 4 Seater See saw- The See Saw consists of 2 poles of Dia 114mm and thickness of 2.5mm which balances the horizontal rod at the center which is of size 1614 mm length and Dia 114 mm. It consists of 4 seats which is made of LLDPE virgin plastic of size 364 mm X 250 mm X 180 mm. Each seat consists of a safety stand in the horizontal balance bar which is of 500 mm X 462 mm and a thickness of dia 32 mm. Specialized connectors such as clamps and couplings are to be cast from aluminium which is pre-treated, and cured, with a baked on powder coat finish. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. ALL WELDING IS CARRIED OUT BY ROBOTS [SIMMILIAR TO THE ONES USED IN THE AUTOMOBILE INDUSTRY], WHICH GUARANTEES STRONG AND SMOOTH WELDS ELIMINATING ANY RAG, WELD SCARS AND ENSURES THE INTEGRITY AND STRENGTH OF THE WELDED AREAS. L x W x H ) 2-60 m x 0.5 m x 0.7 m. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:1%: 3 (1 cement : 11/2 coarse sand : 3 graded stone aggregate 20mm nominal size) of required size as per department/ manufacturers specifications and guidelines. (The fixing charges of C:C Block shall be paid Separately)-

Supply and Fixing of Monkey Bar. Support posts of height 2.1 m are to be schedule Galvanized steel with a 89 mm OD {Outer Diameter}.Al} the posts are to be finished with a baked on powder coat finish. Specialized connectors such as clamps and couplings are to be cast from aluminium which is pretreated, and cured, with a baked on powder coat finish- Handrail of size 0.94 m and Dia 32 mm shall be an all-patent welded unit, fabricated from 32 O.D. galvanized steel pipes with a baked on powder coating finish. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. ALL WELDING IS CARRIED OUT BY ROBOTS [SIMMILIAR TO THE ONES USED IN THE AUTOMOBILE INDUSTRY], WHICH GUARANTEES STRONG AND SMOOTH WELDS ELIMINATING ANY RAG, WELD SCARS AND ENSURES THE INTEGRITY AND STRENGTH OF THE WELDED AREAS. L x W x H)2.91 m x 1.11 m x 2.2 m. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:11h: 3 (1 cement : lh coarse sand : 3 graded stone aggregate 20mm nominal size) of required size as per department/ manufacturers specifications and guidelines. (The fixing charges of C:C Block shall be paid Separately).

Supply and fixing of 2 Seater See saw The See Saw consists of 2 poles of Dia 114mm and thickness of 2.5mm which balances the horizontal rod at the center which is of size 1614 mm length and Dia 114 mm. It consists of 2 seats which is made of LLDPE virgin plastic of size 363 mm X 250 mm X 155 mmEach seat consists of a safety stand in the horizontal balance bar which is of 500 mm X 462 mm and a thickness of Dia 32 mm. Specialized connectors such as clamps and couplings are to be cast from aluminium which is pretreated, and cured, with a baked on powder coat finish. Bolts, nuts, screws, washers and etc used for assembly Shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. ALL WELDING IS CARRIED OUT BY ROBOTS [SIMMILIAR TO THE ONES USED IN THE AUTOMOBILE INDUSTRY], WHICH GUARANTEES STRONG AND SMOOTH WELDS ELIMINATING ANY RAG, WELD SCARS AND ENSURES THE INTEGRITY AND STRENGTH OF THE WELDED AREAS. L x W x H 1.91 m x 0.5 m x 0.82 m. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 3 (1 cement : Ih coarse sand : 3 graded stone aggregate 20mm nominal size) of required size as per department/ manufacturers specifications and guidelines. (The fixing charges of C:C Block shall be paid Separately).

Supply and fixing of Toddler Swing Item Descriptions Product Area : 3.3m x 1.0m (10.8ft X3.3ft) Safe Play Area : 4.3m x 2.0m (14ftX6.6ft) Technical Specification: Centersupport :IOONB Pipe welded together to form a rigid vertical support frame to withstand pitching, rolling & yawing moment- The with a circular flange & square plate IOONB pipe is hot dip galvanized pipe of height 2775mm conforming to IS 1239 with Gl thickness of 60g The ISA & tor rods are fixed to the lower end of the pipe so as to make strong foundation. Top pipe : 50NB Top Pipe with Flange welded at its center& covered both sides with end caps. Pipe can withstanding torsional stress created due to swinging motion. This 50NB top pipe is hot dip galvanized pipe of length 2950mm conforming to IS 1239 with GT thickness of 601.1. Seat assembly : 1) Swing clamp assembly : Swing clamps made up of two parts are joined together with M6 Allen bolts along with S-Hook & a specially designed swing pin. The S-Hook is specially designed to house a bearing for smooth & noiseless swinging. The clamps are made from injection molded Nylon-6 plastic. 2) Chain :Rubber dip molded swing chain of dia. 6mm & 1450mm Long. 3) Hook :S-Hook of dia 8mm & 145x130 Triangular hook of Grade SS 304. 4) Seat :Rubber Seat made up from the nitrile rubber & It is tested for Shorea hardness using Durometer. FRP Joker Face :The FRP Joker Face is made up of Fiber reinforced plastic(FRP). Pins and Circlips: 12mm diameter pins shall be made from EN8 material &Circlip AID. Bearing: Bearing is self-lubricated made of SKF/ NTN/ NACHI make shall be provided for smooth & trouble-free movement. Pipes: All metal pipes are Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with Gl thickness upto 60micron. FRP product :AII the Fibre Reinforced Plastics (FRP) materials are processed by the hand laid process which is considered to be the best of its type. We use international quality of Gel coats which is duly mixed with U.V stabilized pigment to give the required colour to the product. Thickness ofthe FRP material varies from 3 mm to 5 mm as per the product. The FRP material is tested for abrasion resistance & UTS (ultimate tensile test). Pipe Materials or Class: Light Duty CA' Class) & Medium Duty Class) Series of pipes only. Wall thickness of pipe varies according to class /series of pipe used. Powder coating: It shall be done with pure polyester raw material.Dry film Thickness maintained within the range of 50-70 microns. It is tested for adhesion test (According to ASTM-D-3359) with the help of cross hatch cutter instruments. Nut and Bolts: Galvanized/ S.S./Allen Bolt/Button Head Allen Bolt & Nuts / Nylon Lock Nuts are used with PVC Bolt Caps. All open ends of pipe been closed by G.l / PVC caps for user safety against entrapment. Certificate: IS09001:2015 Color: Multicolor for optional or customized & according to RAL shade. Packaging: Safety 3 layer packaging like 1st EPE Foam 2nd HDPE Film and 3rd is Stretch wrap. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 3 (1 cement : I coarse sand : 3 graded stone aggregate 20mm nominal size) of required size as per department/ manufacturers specifications and guidelines. (The fixing charges of C:C Block shall be paid Separately).

Supply and fixing of A Swing. "A" Shaped support posts of height 2.0 m are to be schedule Galvanized steel with a 80mm OD {Outer Diameter}.All the posts are to be finished with a baked on powder coat finish. Specialized connectors such as clamps and couplings are to be cast from aluminium which is pre-treated, and cured, with a baked on powder coat finish. Top rail of length 2.6 m and Dia 6() mm shall be an all-patent welded unit, fabricated from O.D. galvanized steel pipes with a baked on powder coating finish. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel- Flat Swing seat of size 440 mm x 153 mm x 30 mm, Plastic Components. ALL WELDING IS CARRIED OUT BY ROBOTS [SIMMILIAR TO THE ONES USED IN THE AUTOMOBILE INDUSTRY], WHICH GUARANTEES STRONG AND SMOOTH WELDS ELIMINATING ANY RAG, WELD SCARS AND ENSURES THE INTEGRITY AND STRENGTH OF THE WELDED AREAS. Size: (L x W x H )2.75 m x 1.53 m x 2.0 m. All complete as perthe direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:1h: 3 (1 cement : 1% coarse sand : 3 graded stone aggregate 20mm nominal size) of required size as per department/ manufacturers specifications and guidelines. (The fixing charges of C:C Block shall be paid Separately).

Supply and fixing of Animal MGR.item Description Product Area : 2.1m Dia (7 ft Dia.) Safe Play Area : 3.1m Dia (10.2 ft Dia.) Technical Specification: MGR frame : MGR Frame made from 40NB pipes welded together with bottom end over a circular plate meant for assembling bearing assembly. The top end of the pipe is welded with a ISF & a plate for mounting the animal (duck) over it. The four 40NB pipe are hold together with four 25NB pipe to form a strong structure. The Gl plated bowl is used to cover the top of the bearing assembly. Bearing assembly :Bearing assembly with two bearings 1. Ball Bearing used for smooth rolling action. 2.Taper Roller Bearing take vertical thrust due to rolling moment & applied weight. The whole structure is mounted on heavy-duty bearing shaft permanently lubricated with water sealant. Centersuppor : 80NB hot dip galvanized center support pipe of length 500mm with Gl thickness of 601.1 .This pipe is welded with a 150x150mm base plate at bottom for fixing the foundation angles ISA & Circular plate on top with OD 200mm for assembling the bearing. Foot rest :Foot rest made from 15NB Galvanized pipe with end caps welded to two plates forminga foot rest. Duck: Duck is made out of molded plastic in rotational molding process. Rotational MoldedProducts :The ROTO products are manufactured using material LLDPE {Linear Low Density Polyethylene) with UV stabilization of Food Grade Non Hazardous Plastic compiled to ROHS. Thickness of the ROTO products varies from 5 mm to 8 mm as per the product. The overalE product obtain is a seamless to ensure perfect blend of uniform thickness & durability. Pipes: Ali metal pipes are Hot Dipped Galvanized Pipes with Gl thickness upto 60micron. Pipe Materials or Class: Light Duty Class) & Medium Duty ('B' Class) Series of pipes only. Wail thickness of pipe varies according to class / series of pipe used. Powder coating: It shall be done with pure polyester raw material. Dry film Thickness maintained within the range of 50-70 microns- It is tested for adhesion test (According to ASTM-D-3359) with the help of cross hatch cutter instruments. Nut and Bolts: Galvanized/ S.S./Allen Bolt/Button Head Allen Bolt & Nuts / Nylon Lock Nuts are used with PVC Bolt Caps. All open ends of pipe been closed by Gl / PVC caps for user safety against entrapment. Certificate: IS09001:2015 Color: Multicolor for optional or customized & according to RAL shade. Packaging: Safety 3 layer packaging like 1st EPE Foam 2nd HDPE Film and 3rd is Stretch wrap. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:1%: 3 (1 cement : lh coarse sand : 3 graded stone aggregate 20mm nominal size) of required size as per department/ manufacturers specifications and guidelines. (The fixing charges of C:C Block shall be paid Separately)-

Supply and fixing of N Swing inverted "U" Shaped support posts of height 2.1 m are to be schedule Galvanized steel with a 80mm OD {Outer Diameter}. All the posts are to be finished with a baked on powder coat finishSpecialized connectors such as clamps and couplings are to be cast from aluminium which is pretreated, and cured, with a baked on powder coat finish. Toprail of length 2.5 m and Dia 89 mm shall be an all-patent welded unit, fabricated from O-D. galvanized steel pipes with a baked on powder coating finish. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shah be of tamper resistant stainless steel. Flat Swings seat of size 430 mm x 180 mm x 50 mm, Plastic Components. ALL WELDING IS CARRIED OUT BY ROBOTS [SIMMILIAR TO THE ONES USED IN THE AUTOMOBILE INDUSTRY], WHICH GUARANTEES STRONG AND SMOOTH WELDS ELIMINATING ANY RAG, WELD SCARS AND ENSURES THE INTEGRITY AND STRENGTH OF THE WELDED AREAS. Size: (L x w x H )2.6 m x 1.26 m x 2.1 m. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:1h: 3 (1 cement : 1% coarse sand : 3 graded stone aggregate 20mm nominal size) of required size as per department/ manufacturers specifications and guidelines. (The fixing charges of Block shall be paid Separately)-

MULTI ACTIVITY PLAYS SYSTEM ACTUAL EQUIPMENT SIZE: 22 X 22 X 11 FT. MINIMUM RECOMMENDED AREA: 28 X 28 X 13 FT. CHILDREN CAPACITY: 25 CHILDREN MATERIAL SPECIFICATION: STRUCTURE GYMS PIPE: Class-B and conforming to IS-1239. OD - Hot Rolled Soft Steel Stripes or forged. LLDPE PLASTIC PARTS: UV Stabilized. Narrow MWD, Excellent Process ability, Good Impact Strength & Stiffness, Excellent Internal & External Surface Finish. ACRYLIC: Acrylic clarity, light weight, impact resistance, and weather resistance. HDPE PARTS: UV Resistant. Anti Static. Good Electrical Properties. PLATFORM & LADDER: CR Sheet 1.6 mm thickness, high strength and improved formability. ALUMINIUM CLAMP: high fatigue strength, excellent castability, very good corrosion resistance, self-piercing riveting and clinching. PP CAPS: caps are manufactured from high quality polymers. Gl HARDWARE: All galvanizing Hardware are carried out by the hot dip process, in accordance with Specification IS 2629. VINYLE STICKER: High Strength Acrylic Adhesive 300 is designed to be compatible with a variety of print methods and end use applications. MIG WELDING: MIG welding is versatile and can be used with a wide variety of metals and alloys, corrosion resistance, soft surface to prevent injuries. POWDER COATING:The finish is more flexible than traditional paint, and allows for a small amount of bending and flexing as parts vibrate and move. It is also resistant to scratching, flaking, and corrosion. BUBBLE WRAP: Thickness of 6 mm. Bubble wrap is lightweight, water resistant, reusable non scratching. And, Commonly used for packing fragile items.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:1%: 3 (1 cement : 1% coarse sand : 3 graded stone aggregate 20mm nominal size) of required size as per department/ manufacturers specifications and guidelines. (The fixing charges of C:C Block shall be paid Separately).

PART – ‘B’ . Installation of Open Gym :-

Providing and Installation of AERIAL STROLLER Design, Shaped and size of Air Walker as per standard given by the manufacturer. The Air Walker fabricated with main post of 89mm O.D. dia "c" class Gl pipe as per IS- 1239 other pipes of 40mm dia "c" class Gl pipe G-l. Pipe as per IS-1239 having powder coated 80-120 micron at thick G.I. using Akzo Nobel or equivalent in desired shade and colour. Ali welding joints of pipe shall be robotic type welding. All open ends of pipe to be closed with Gl/ LLDPE/ FRP caps, base plate cover shall be made of virgin LLDPE plastic by rotational moulding/ FRP material. A High quality grip rubber should be used on handles, Foothold shall be made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings should be used in the equipments s manufactured by reputed company duly oil sealed and self lubricated to be approved by Engineer-in-charge. The equipment shall be fitted with in-built limiters. The equipment shall be fixed on Ground with concrete after deep excavation work & Circular foundation stand welded bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C(1:1%:3) block of size:After deep excavation/earth work at site as required. All complete as per directions and pre approval of Engineer-in charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc. The fixing charges of equipment shall be paid separately.

Providing and Installation of ABS BOARD DOUBLE Design, Shaped and size of of SIT UP BOARD as per standard given by the manufacturer. Sit up board made from "c" class G.l. pipe. The main frame is of 32mm NB made from "c" class G.i. pipe. The remaining frame of the sit up board is 25mm NB made from "d' class G-l- pipe. A performed G.l. sheet in 2mm is welded on main frame. The foundation pipes are embedded in CC block (which shall be paid separately) and painting by powder coating mall. G.l. using Akzo Nobel or equivalent in desired shade and colour. All welding joints of pipe shall be robotic type welding. All open ends of pipe to be closed with G'/ LLDPE/ FRP caps, base plate cover shall be made of virgin LLDPE plastic by rotational moulding/FRP material. The equipment shall be fitted with in-built limiters. The equipment shall be fixed on Ground with concrete after deep excavation work & Circular foundation stand welded bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:1%:3) block of size:- After deep excavation/earth work at site as required. All complete as per directions and pre approval of Engineer-in- charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc. The fixing charges of equipment shall be paid separately.

Providing and Installation of AERO RIDER Design, Shaped and size of HORSE RIDER as per standard given by the manufacturer. Main post of 65 N.B. and "c" class Gl pipe G.l. Pipe as per IS- 1239 and rest of the pipe 40mm dia and "c" class Gl pipe G.l. Pipe as per IS-1239 and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic type welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact of injury. Base plate cover and seat to be made up from virgin LLDPE/FRP materiai. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be pre approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by Gl/ LLDPE/ FRP caps for user safety. The equipment to be fixed on Ground with concrete after deep excavation work & Circular foundation stand welded bolt and once the concrete is set, fix the equipment on to it and cover with the base plate. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:1%:3) block of size:- after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. The fixing charges of equipment shall be paid separately.

Providing and installation of FOREARM TWIRL DOUBLE/ TAICHI SPINNER. The products must tested and certified to meet EN16630 safety standards with GS test mark- The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature-Joints are Robotic Welded. Alf welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA -USA Powder Coatings to the thickness of 130-180 microns. Bearings Maintenance-free ball bearings. Scope of delivery: 1 completely pre-assembled equipment modules Maintenance: Maintain according to EN16630 and the maintenance guide Size (LxWxH) 1245x1070x1500 mm. Capacity 2 persons. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c.c work up to plinth level, c.c block (1:1%:3) 20mm nominal size of required size as per department / manufacturers specifications and guidelines. The fixing charges of equipment shall be paid separately.

Providing and Installation of DOUBLE SHOULDER EXERCISER Design, Shaped and size SHOULDER EXERCISE as per standard given by the manufacturer. With main post of 114mm dia and "c" class Gl pipe G.l. Pipe as per IS-1239 Hand rest of the pipe 40mm dia and "c" class Gl pipe G.J. Pipe as per IS-1239 and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic type welded with joints scalloped as necessary and dressed off removing sharp edges and burrs- Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber on top end. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury seat and base plate coverto be made up from virgin LLDPE/FRP material. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by Gl/ LLDPE/ FRP material caps for user safety. The equipment to be fixed on Ground with concrete after deep excavation work & Circular foundation stand welded bott and once the concrete is set, fix the equipment on to it and cover with the base plate. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:1%:3) block of size:- after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. The fixing charges of equipment shall be paid separately.

Providing and fixing of CHEST PRESS DOUBLE Design, Shaped and size of CHEST PRESS DOUBLE as per standard given by the manufacturer. main post of 114mm and "c" class Gl pipe made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick- All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Seat and base plate cover to be made from virgin LLPDE/FRP material. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge- Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C;C (1:1%:3) block of size:- after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. The fixing charges of equipment shall be paid separately.

Providing and Installation of SURF BOARD DOUBLE Design, Shaped and size of SURF BOARD as per standard given by the manufacturer. The Surf Board fabricated with main post of 114mm dia "c" class Gl pipe. G.l. Pipe as per IS-1239 Hand rest of the pipe 40mm dia "c" class Gl pipe G.l. Pipe as per IS-1239 having powder coated using Akzo Nobel or equivalent of 80 120 micron thick. Att joints of pipe are robotic type welding with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin LLDPE/FRP material Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movements. All open ends of pipe to be closed by GI/ LLDPE/ FRP caps for user safety- The equipment to be fixed on Ground with concrete after deep excavation & Circular foundation stand welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:1%:3) block of size:-deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineering charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. The fixing charges of equipment shall be paid separately.

Providing and fixing of HIP TWISTER DOUBLE Design, Shaped and size of HIP TWISTER DOUBLE as per standard given by the manufacturer. with main post of 114mm and "c" class Gl pipe made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick- All joints of pipe are robotic TYPE welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Rotating and base plate cover to be made from virgin LLPDE/FRP material. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:1%:3) block of size: after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. The fixing charges of equipment shall be paid separately.

Providing & fixing of Dual SKY WALKER Design, Shaped and size of SKY WALKER as per standard given by the manufacturer. main post of 114mm dia and 'f' class Gl pipe G.l. Pipe as per IS-1239 and rest of the pipe 40mm dia a G.l. Pipe as per IS-1239 and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic type welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury and base plate cover to be made up from virgin LLDPE/FRP material. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by G'/ LLDPE/ FRP material caps for user safety. The equipment to be fixed on Ground with concrete after deep excavation work & Circular foundation stand welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:1%:3) block of size:- after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. The fixing charges of equipment shall be paid separately.

Providing and fixing of SHOULDER TWIRL DOUBLE Design, Shaped and size of SHOULDER TWIRL DOUBLE as per standard given by the manufacturer. fabricated with main post of 114mm "c" class Gl pipe made of hot rolled tubular steel and hot dipped galvanized and powder coated using AkzoNodel of 80-120mm micron thick. Ail joints of pipe are robotic type welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:1%:3) block size:- after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. The fixing charges of equipment shall be paid separately.

Providing and Installation of DOUBLE PARALLEL BAR Design, Shaped and size with the COMBINATION of Leg press & EXCERSING BAR as per standard given by the manufacturer. The center frame of the PARALLEL BAR is fabricated with main post of 114mm and "c" class Gl pipe made of hot rolled tubular steel and hot dipped galvanized and powder coated using. Handles are made up of 25NB G.l. pipes. One pair of handiesare attached to main frame in two opposite exercising bars. All pipes are uniformly powder coated up to minimum 80-100 micron thickness to avoid corrosion. All complete as per the technical specifications to manufacture the item. The Complete item to be fixed in C:C (1:1%:3) block of size:- after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in- charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc. The fixing charges of equipment shall be paid separately.

Providing and fixing of HAND ROWER Design, Shaped and size of ROWER MACHINE as per standard given by the manufacturer with main post of 114mm dia and "c" class Gl pipe and FRP (Fiber Reinforced Plastic seat with backrest is fixed over 40NB Galvanized bend pipe. This bend pipe is further linked to 65 N.B base pipe&"c" class Gl pipe with help of connecting links. Connecting links are made up of 25NB G.l. pipes with specially designed metal bush at ends. The paired 25NB pipe handie with rubber grip at the end is fixed over one of the connecting link. The rolling frame is made by 40 NB & 20 NB G.I. pipes. Connecting links are hinged in between seat frame and base frame with specially designed bush bearings. A suitable PVC/ rubber grip is provided for foot rest on seat frame. All pipes are uniformly Polyester based powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by Gl / HDPE caps for user safety against entrapment. Handle for rotating the ring fixed over the pipe ring. The Pipe to be used of standard make and c-class. All complete as per the technical specifications to manufacture the item- The Complete item to be fixed in C:C (1:1h:3) block of size:- after deep excavation/earth work at site as required. All complete as per direction and Pre approval of engineer in charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipmentsetc- The fixing charges of equipment shall be paid separately.

Providing and Installation of Leg Extension. The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA USA Powder Coatings to the thickness of 130- 180 microns Bearings Maintenance-free ball bearings The Seat, backrest and Base plate cover are manufactured from Virgin LLDPE Scope of delivery Maintenance 1 completely pre-assembled equipment modules Maintain as per maintenance guide Size (LxWxH) 13x620x70mm Capacity 1 persons All complete as per the direction of engineer in charge as per approved drawing & design given by manufacturer including earth work cc work up to plinth level C:C block(1:1%:3) 20mm nominal size of required size as per department / manufacturers specifications and guidelines. The fixing charges of equipment shall be paid separately.

Providing and Installation Arm and pedal bike. The products must tested and certified to meet EN16630 safety standards with GS test mark. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using AKZO Nobel Great Wall Powder to the thickness of 80120 microns. All metal parts are tested in a 5% NaCL solution in accordance to IS07227 to speed up corrosion for 3000 hrs. The seat is made from Roto moulded LLDPE Bearings: Maintenance-free ball bearings. Scope of delivery. 1 completely pre-assembled equipment modules. Maintenance: Maintain according to EN16630 and the maintenance guide- Size (LxWxH) '830 MM x 500 MM x 1450 MM. Capacity 1 person. A cycling and upper arm exercise rolled into one. Co-ordination between leg and arm movement encourages balance whilst exercising too. All complete as per the direction ofengineer in charge or as per approved drawing & design given by manufacturer including earth work, cc work up to plinth level, C:C (1:1%:3) block 20mm nominal size of required size as per department/ manufacturers specifications and guidelines. The fixing charges of equipment shall be paid separately.

PART – ‘C’ ... Construction ofSBR (Styrene butadiene Rubber) :-

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. 2.28.1 All kinds of soil

Excavating holes more than 0.10 cum &upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m. 2.30.1 All kinds of soil

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete.

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1.2- 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction 1043 SUB HEAD : 16- ROAD WORK of Engineer-in-charge (length of finished kerb edging shall be measured for payment).

Providing SBR (styrene butadiene Rubber) tile flooring 24 mm thick with group arrangement of approved colour and size and fixingwith P. U. adhesive for reliable and durable bonding with sub-base all complete and as approved by Engineer-in-charge-

PART – ‘D’ .Development of a park with sitting arrangement :- ,

Trenching in ordinary soil up to depth of 60 cm including Removal and staking of serviceable materials and then disposing of by 50 mtr and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/ and manure before and after flooding trench with water(excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage up to 10 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking of dung Manure at site including royalty and carriage up to 1 km (earth; measured in stacks will be reduced by 8% for payment).

Supplying and spreading of Yamuna sand at site..

Carriage of good earth by manual labour including loading/ unloading & stacking for lead) For first 50 mtr.

Carriage of manure or sludge by manual labour including loading/ unloading & stacking for lead a) For first 50 mtr

Carriage of Yamuna Sand by manual labour including loading/ unloading & stacking for lead a) For first 50 mtr

Rough dressing to the trenched area after 10 to 15 days of its flooding with water including breaking clods.

Fine dressing the ground

Mixing earth and sludge, dung manure in proportion specified or directed

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and stacking of Ficus panda of height 45-60 cm. with 6-7 branches and healthy foliage in p.bag of size 25 cm as per direction of theofficer-in-charge.

Providing and Displaying Golden Bottle brush Topiary well developed with fresh & healthy foliage 5 to 6 big ball 115 to 180 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Washingtoniafilifea palm stem ht. 120-135 cm with 8-10 healthy leaves lush green leaves well developed in big size HDPE Bags as per direction of the officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Bamboo Buddha valley with fresh & healthy 3 to 4 suckers having 75 to 90 cm ht. in 25 cm size Earthen Pot/ Plastic Pot asper direction of the officer-in-charge.

Providing and fixing of RCC Benches, the Specification as under:- Description: This item shall govern the provision of supply, erecting and installation of precast concrete reinforced benches with back rest. 1. General Requirement: The precast concrete reinforced benches shall be manufactured in accordance with the design requirements and details shown in the plan, and in conformity with the requirement of this specification and item no. 172020 of USSOR. 2. Materials and Construction Methods: The material and construction of precast concrete reinforced benches will be as follows: (i) Concrete Mix Design: The benches shall be cast using M-30 grade concrete mix in accordance with IS:10269: 2009 (with latest amendment) in gray cement by using vibro- compaction technique and with reinforcement as detailed in this specification. The manufacturer shall be responsible to design a mix which achieves both the strength and the surface finish required for the installation and application. Compressive strength shall be not less than 30 MPa at 28 days. (ii) Reinforcement Steel: TMT reinforcement bars confirming to IS: 1786:2008 of dia 10mm shall be used as main reinforcement bar and 4mm dia mild steel bars shall be used as stirrups as per reinforcement diagram. (iii) Connections: 12mm dia x 65mm long galvanized steel CSK (Countersunk) bolts with EVA (Ethylene Vinyl Acetate) washer for connecting seating plank with leg and half threaded carriage bolts & nuts with EVA & steel washers of size 165mm length x8mm dia for connecting back rest plank with leg. Threaded steel fastener shall confirm to IS: 1367 with latest amendments. (iv) Paint :Red color acrylic based paint (Other color may be used, if decided by Engineer-in-charge) confirming to IS: 15489 should be used. 3. Detail of member of precast concrete reinforced bench: i. RCC Base Supports: Two number of legs manufactured using M-30 grade grey cement concrete of back height 1000mm, front height 400mm, bottom width 620mm with 100mm thickness. Each leg shall be reinforced with 4 nos. of 10mm dia TMT bars distributed uniformly along the section and periphery of the legs and tied with 4mm dia mild steel stirrups as per detailed given in drawing Each leg will have 3 nos. 12mm dia 65mm length galvanized coupling nuts, welded suitably to the main reinforcement at appropriate location on the seating to receive concrete planks on the legs and 3 holes to receive carriage bolts for fixing back rest planks. ii. Planks: Five RCC planks of size 1500mm x 100mmx50mm shall be cast using M-30 Grade grey cement mixed with 3% red pigment (other color may be used, if decided by Engineer) and each plank reinforced with 2nos.10mm dia TMT bars along the length and 10 Nos. 4mm dia mild steel bars along the width and having 2 holes of 14mm dia at appropriate location to receive 12mm dia galvanized bolts for fixing these planks on the legs. One RCC plank. iii. Installation of RCC bench: Each seating plank (bottom) of bench will be bolted with the leg with the help of 12 dia x65mm length galvanized steel CSK (Countersunk) bolts with EVA and steel washers of size 165mm length x 8mm dia.

Fair Deal Creation and Marketing

Sunrise Enterprises