REPAIR TO BOUNDARY WALL GATES FENCING SECURITY WALL HARD STANDING WASTE DISPOSAL SYSTEM, DRAIN, RAINWATER PIPE, VALLEY GUTTERS AT COMMON AREA AND INS ABHIMANYU AT NAVAL STATION KARANJA

Amount

Demolition of stone/brick masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facings dressed stone work and pre cast concrete articles complete all as specified and directed.

-ditto all as per srl item No. 1 above but pre-cast concrete block walling complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width in type B1 (1:2:4) and setting in mortar (1:6) complete all as specified and as directed

M&L brickwork with sub class 'B' bricks , straight or curved on plan exc 6m mean raidus built in cement mortar 1:6 complete all as specified and directed

All as per srl item No. 4 here in before but except bricks Note:- Serviceable bricks obatined from srl item No. 1 shall be re-used in srl item No. 5 after cleaning etc complete all as specified and directed by Engr-in-Charge.

M&L for walling of random rubble, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 all as specified and directed.

-Ditto- all as per item No. 6 hereinbefore but except stone. Note:- stone obtained from item No 1 shall be reused.

M&L for raised pointing to random or polygonal rubble masonry uncoursed or brought upto course in CM (1:4) complete all as specified and directed.

M&L for raised pointing to precast concrete block masonary wall in CM (1:4) complete all as specified and directed.

Taking down cement plaster on brick walls or stone walls etc including raking out joint, hacking for key, scrubbing down with water etc including removing debries directed for a distance max upto 500m complete all as specified.

M&L using ready mix plaster for rendering 15 mm thick in CM 1:4 on fair faces of brick/concrete surfaces , finished even and smooth complete all as specified and directed. (Note:- Item rate shall be include any height of Bldgs for scafolding as all arrangement.) (WPC paid and measured seprately)

M&L for new or previously untreated surfaces of any description & applying two coats of acrylic (antifungal) exterior grade paint over one coat of primer on wall/roof complete all as specified and directed

Supply only liquid water proofing compound mix cement concrete/cement plaster as per manufacture instruction all as directed by Engr-in-Charge. Make : DR. FIXIT PIDE PROOF LW, FOSROC

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick below or above ground level un re-inforced complete all as specified and directed. .

M&L for PCC 1:4:8 type D2 using (40mm graded stone aggregate) as in foundations, fillings & mass concrete etc all as specified and directed.

M & L for cement concrete 1:2:4 type B2 (using 40mm graded stone aggretate) as in surface channel or drain complete all as specified and directed.

M&L PCC 1:2:4 type B1 using (20 mm graded aggregate) as in roof kerbing, or mud stops, rounded or chafered on edges and all around of chequered tile complete all as specified and directed.

M&L for PCC (1:3:6) type C1 using 20mm graded stone aggregate in coping bed black etc including necessary form work complete all as specified and directed.

M & L PCC 1:3:6, type C2 (using 40 mm graded agg) 75 mm thick as in plinth protection without using extra cement complete all as specified and directed.

M&L for machine cut broken stone or boulders of gauge not exc 63mm as in hard core n exc 150mm thick spread and levelled including watering & ramming all as directed by Engr-in-Charge.

M&L, for providing 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded aggregate in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L for 100mm thick cement concrete type B-2 1:2:4 using 40mm graded crushed stone aggregate as in path/floor finished fair even and smooth without using extra cement, laid in alternate panels of size not exc 4 sqm each complete all as specified and as directed by Engr-in-Charge.

M&L for 25mm thick Wearproof topping using metallic floor hardener as per manfacutre's instruction, as specified (incorporating an approved metallic floor hardner), laid on concrete floors and pavings and path, and finished even and smooth (except metallic hardner) all as specified and directed by Engr-in-Charge. (Note metallic hardender & glass strips area measured and paid separately).

Supply only 22 mm wide and 3 mm thick glass dividing strips as laid in floor all as specified and directed by Engr-in-Charge.

Supply on metallic hardner mix with cement cncrete as per manufacture instruction all as directed by Engr-in-Charge. Make : DR. FIXIT PIDE PROOF LW, FOSROC

Dismantling of stone slabs & tiles of any description or thickness in floor aprons, cills etc laid bedded & pointed in any mortar complete all as specified and directed.

M&L Chequered cement concrete tiles 300x300x25mm thick, set jointed and pointed in near cement slurry in floors with gray cement and pigments in any colour machine preassed glazed , over cement screed bed 15mm thick cement motor 1:6 all as specified and as directed by Engr-in-charge.make nitco/arena or equivalent all as specified and directed by Engr-in-Charge.

M&L 60 mm Machine pressed pre casted pressed cement concrete inter locking paver blocks glazed coloured up to 6mm on the top in any shape and size, strenth not less than M-35 all as directed by Engr-in-charge

M&L Sand filling under floors or in foundations including watering and consolidation

Demolition of reinforced (reinforcement cut as required to facilitate demolition) cement concrete in ground floors and paving not exceeding 15 cm thickness( below or above ground level) all as directed.

M&L for precast cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) setin cement mortar (1:4) work for landings, cover slabs, manholes, chajjas, water troughs, manger shleves and similar articles with plain faces complete all as specified and as directed

S&F of Bands, straps,supports or stays for rainwater, ventailing pipes, including bolts, if required hooks,heavy, for large gates, hook and pintle hinges; large hasps and stables; chains;hand made sliding bolts; clamps; hold fasts; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 Gde -165. complete all as specified and directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided incl doors, gates for complete all as specified and as directed

S&F for MS as in posts and struts in fencing angle including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing with mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 (Gde-E-165 quality-B. Note:-Posts/struts of angle iron made to shape shall be welded to existing angle iron bracket of security wall, contractor shall make his own arrangement for welding for boundary wall by using gen sets or any alternative arrangement all as specified and directed by Engr-in-Charge.

S&F mild steel works as in doors or gates (ornamental) of angle or other sectons with gusset plates, rails, braces etc complete drilled, welded etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete.

M&L for welding in repair, exc 2.5 cm but n.exc 5 cm in length thickness of metal to be welded exc 20mm but n.exc 25mm all as specified and directed by Engineer-in-Charge.

M&L for running welding in repair exc 20mm but n ecx 25mm as directed by Engr-in-Charge

M&L painting the surfaces of steel any description over 10cm in width or girth, with two coats of synthetic enamel paint over a coat of red oxide incl preparation of new steel surface. complete all as specified and directed by Engineer-in-charge.

Preparation of old painted steel surfaces of any description not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint all as specified and directed by Engineer-in-Charge.

S&F Galvanized 2 stand Steel Barbed wire 2.24mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standerd rails, straining bolts,including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc incl taking down of existing barbed wire as directed (each line wire to be measured) complete all as specified and directed by Engr-in- Charge

Restriaining resecurig including making good staples or tighting of cross wire galvanised barbed wire in any dia of wire or any spacing all as specified and directed by Engr-in-Charge.

Taking down and refixing in same position after replaing of damage of fencing post concertina coil any dia reinforced punched(chrome razor or blade wire with barbed top of 0.5mm thick galvanised sheet and core wire of dia 2.5mm of high tensile steel wire incuding galvanised MS staples/Clips for tying at crossing complete all as specified and directed by Engineer–in-Charge

S&F in repair any dia concertina coil directed by Engr-in-Charge reinforced punched(chrome razor or blade wire with barbed top of 0.5mm thick galvanised sheet and core wire of dia 2.5mm of high tensile steel wire incuding galvanised MS staples/ Clips for tying at crossing complete including taking down of existing concertina coil all as specified and directed by Engineer–in-Charge

Taking down existing angle iron from wall embadded in PCC and refixing in the same opening/position complete all as specified and as directed by Engr-in-Charge.

S&F mild steel security chain link fencing 60mmx60mm with PVC coated mesh made out of 3mm dia MS wire and 1.00mm thick PVC coating throughout fixed to RCC post including binding wire complete and incl taking down of existing chain link fencing all as specfied and directed.

S&F mild steel round bars 10mm dia and over, in horizontal support for chain link straining of fencing including cut to length, bent to shape required including cranking, bending spirally for hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-W (Gde E-250) complete all as specified and directed.

S&F mild steel screw bolts 10mm dia with hexagonal or square heads at one end and screwed at other ends dia of shank 5 to 10 mm and length of bolt exc. 5cm but n.exc 10cm complete all as specified and directed.

M&L mild steel TMT bars 6 to 8mm dia and over cut to length bent shape as required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-S complete all as specified and as directed

Dinesh Enterprises

HINDUSTAN BUILDERS

BALAJI TRADERS

S N TRADERS

Mahadev Enterprises

M/s S.D Construction Co

M/s Vishwakarma Enterprises