GENP-24/2020-21 ADDITIONAL/ALERATION TO ARJAN BLOCK AND SPECIAL REPAIR TO SUBROTO AND LATIF BLDG AT AF PALAM UNDER GE (AF) PALAM DELHI CANTT-10

Amount

PART-I (B/R PORTION) Taking down cement plaster on brick or concrete wall surfaces etc including raking out joints, hacking for key , scrubbing down with water etc.

M&L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces including finished even and smooth surface without using extra cement.

M&L for 10 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces including finished even and smooth surface without using extra cement. and using water proof compound. NOTE: Water proofing compound shall be measured and paid saperately.

M&L for 10 mm thick cement plater in cement mortar 1:3 on concrete surfaces in ceiling including finished even and smooth surface without using extra cement..

M&L for complete removal of existing old treatment and applying two coats of plastic emulsion paint (Interior) over a coat of primer over 3mm thick wall care putty on walls.

M&l for two coats of plastic emulsion paint (Interior ) over a coat of primer over 3mm wall care putty to obtain smooth regular / even finished surface using sand paper including preparation of newly plastered surfaces.

M&l for two coat of plastic emulsion paint (Exterior) over a coat of primer over 3mm wall care putty to obtain smooth regular / even finished surface using sand paper including preparation of newly plastered surfaces.

M&L for applying one coat of plastic emulsion paint (Exterior) including preparation of old treated plastered surfaces on walls.

Supply only integral water proofing compound ISI marked.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) n.exc. 1.5 Sqm each.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) exc. 1.5 Sqm and n.exc. 4 Sqm each.

S&F for factory made fibre glass reinforced plastic (FRP) door frame, three lagged of cross section 90 mm x 45 mm having single rebaetd of 32mmx15 mm to receive shutter of 30 mm thickness, moulded with fire retardant grade unsaturated polyesterresin and chopped mat. Door frame lamination shall be 2mm thick and filled with suitable wooden block in all over frame. The frame shall be covered with fibre glass from all sides including MS stay at the bottom to steady the frame complete all as specified and directed by Engr-in-Charge.

S&F factory made solid FRP door shutter 30 mm thick glass fibre reinforced plastic (FRP) panelled door shutter of required colour and approved brand and manufacturer made with fire retardant grade unsaturated polyester resin mouled to 3 mm thick FRP laminated for forming hollow rails and styles with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP panels and confirmign to IS 14856-2000 complete all as specified and directed by Engr-in-Chrge.

M&L for factory made pressed steel frame for door with single rebated of size 105mm x 60 mm including necessary fixing lugs, hinges , lock strike plate etc complete all as specified and directed by Engr-in-Chrge.

S&F for 35mm thick factory made second class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete.

Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles and rubbish off the premises from site to outside of MoD land.

Material and Labour for Joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but n exc 0.18 Sqm as in flooring etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6.

Material and Labour for glazed ceramic tiles coloured printed of size 450x300x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in vertical surface,dado,skirting etc over and including 10 mm thick cement plaster in CM 1:4.

M&L for double charged vitrified coloured tiles ( light shade ) 10 mm thick (square/ rectangular) polished, area of each tile exceeding 0.36 sqm but not exceeding 1.00 sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed/bedding in CM 1:6. Note for item No.17 to 19:- Rates also includes in the item for necessary raking,circular cutting or notching and waste on tiles.

M&L for preparation of newly wooden surfaces of any description, not otherwise described,over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M&L for one coat of synthetic enamel paint including preparation of old wooden surfaces of any description, not otherwise described, over 10cm width or girth complete.

M&L for preparation of newly steel surfaces of any description, not otherwise described,over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

Dismantling of brick tiles Single layer on roofs laid dry or with cement mortar and removing the debris from site to outside MoD land.

M&L for precast cement concrete tiles, glossy finished rubber moulded, machine made of 22 to 25 mm thick of any size and pattern as approved by GE as per IS-1237 of make ultra designer tiles indian series or its equivalent in NITCO/CORAL/ HINDUSTAN as in terrace/floors etc set, jointed and pointed in neat cement slurry and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed by Engineer-in-charge

Surface excavation in any type of soil not exc. 30 cm deep and averaging 15 cm deep.

M&L for hardcore of broken stone or boulders gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surrface.

M&L for 100mm thick cement concrete type B- 2,1:2:4 (40mm graded stone aggregate) as in floor with finished surface even and fair complete.

M&L for 60 mm factory made machine pressed, precast interlocking paver block any shape and size confirming to IS 15658-2006 of M-35 grade with grey cement and pigment over 25 mm thick sand bedding layer complete.

Dismantling asbestos cement (corrugated , semi corrugated etc ) sheets in roof coverings.

S&F for pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / clading to wall fixed with self tapping screws as specified.

S&F 150 mm aluminium anodised,barrel tower bolts of extruded section and fixed.

S&F 250mm aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F 100 mm extruded aluminium alloy handles, fabricated type, anodised.

S&F 100mm Butt hinges, medium weight, cold rolled mild steel, and fixed

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor of size 140 mm.

PART-II (E/M PORTION) Taking down carefully unserviceable copper/aluminium point wiring (light, fan, socket or power) including fixture and fitting such as switches, ceiling rose, lamp holder, regulators, sockets, light fittings, wooden terminal boxes, plastic laminated sheet cover including taking down of meter board any type complete all as specified and as directed.

Taking down unservesiable sub main wiring with conduits/battens etc complete all as specified and as directed.

Taking down unservesiable MCCB/MCB DBs including MCCB/MCBs of any type and capacity complete all as specified and as directed.

Taking down unservesiable light fitting and ceiling fitting any type including disconnecting the connection complete.

M & L for Point wiring with single core PVC insulated unsheathed 1.5 Sqmm FRLSH multistranded copper conductor cable 1100 volts grade IS-694 marked drawn in and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked with all conduit fittings and fixing accessories including modular metal flush box with modullar plate for mounting switches, sockets, fan regulators, etc and earth wire single core PVC insulated unsheathed multistrand copper conductor cable 1100 volts grade IS-694 marked 1.5 Sqmm FRLSH cable as continuous earth wire connecting to common earth dolly in concealed wiring system including making good the disturbed surface of wall for One light point controlled by one switch one way complete.

All as per item No.40 above but for one ceiling fan/exhaust fan point controlled by one switch.

All as per item No.40 above but for one socket outlet 5 Amp controlled by one switch on independent board

All as per item No.40 above but for one 3 pin 5 Amps socket out let point on the same board controlled by one switch complete.

All as per item No.40 above but for one light point controlled by two 2-ways switches with cables 1.5 Sqmm.

All as per item No 40 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 Sq mm stranded copper conductor cable PVC insulated unsheathed multistrand copper conductor cable 1100 volts grade IS-694 marked 2.5 Sqmm FRLSH cable as continuous earth wire connected to earth dolly complete, all as specified and directed.

All as per item No 40 here-in-before but for one power point 6 pin 15 Amps socket out let with 4.0 Sq mm stranded copper conductor cable PVC insulated unsheathed multistrand copper conductor cable 1100 volts grade and 4.0 Sqmm FRLSH cable IS-694 marked as continuous earth wire connected to earth dolly complete all as specified and directed.

Supply and fixing ceiling rose, surface type, 65mm x 50mm, 2 to 3 terminal complete.

Supply and fixing Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete.

Supply and fixing switch piano flush type 5 Amps, single pole one way complete.

Supply and fixing switch piano flush type 5 Amps, single pole two way complete.

Supply and fixing socket out let 2/3 pin 5 Amps, flush type complete, all as specified and directed by Engr-in-Charge.

S&F switch piano flush type single pole one way15 Amps complete.

Supply and fixing socket outlet 2 in 1, 6 pin 5/15 Amps, flush type complete .

S&F Indoor decorative LED battens- integrated type 20 watt 4 feet white fixture with extruded aluminium body suitable for LED tube 20 watt , bipin holder, connector block, LED rod 20 watt etc complete with all accessories internally wired and connecting up with twin core copper conductor cable complete all as specified and directed by Engr-in-Charge. Make - C&S Cat part No. LTTB4F20WLED/W or its equivalent in Polycab/Halonix.

S&F Indoor decorative LED battens- integrated type 10 watt 2 feet white fixture with extruded aluminium body, suitable for LED tube 10 watt , bipin holder, connector block, LED rod 10 watt etc complete with all accessories internally wired and connecting up with twin core copper conductor cable complete all as specified and directed by Engr-in-Charge. Make - C&S cat part No LTTB2F10WLED/W or equivalent in Polycab/Halonix.

Supply and fixing in repalcement of LED bulb 12 watt in replacement of CFL 11/15 watt fixed in pendent holder /bulk head complete all as specified and directed. Make - C&S Cat part No LTHPLEDLAMP 12W/B22 or equivalent to Polycab/Halonix.

S&F wall mounted fan 400mm Air delivery 100mm all as specified and as directed. Make: Bajaj Cat part No 60139 or equivalent in Havelles/orient.

S&F LED recessed mounting square slim LED down lighter 36 Watt for AS/GB/POP ceiling 2'x2' size complete with internally prewired and connecting up with twin core flexible copper conductor cable of suitable size . Make : C & S Cat part No.LTCRSLM36WATT2X2 or its equivalent in Phillips/Havells .

Supply and fixing sheet metal enclosure for distribution board SPN (when MCBs to be used ) 8 way double door, 200 Amps rated bus bars and with neutral earthing bar and din rail complete all as specified and as directed by Engr-in-Charge

Supply and fixing sheet metal enclosure for distribution board SPN (when MCBs to be used ) 12 way double door, 200 Amps rated bus bars and with neutral earthing bar and din rail complete all as specified and as directed by Engr-in-Charge

Supply and fixing in repalcement of vertical type load line distribution board, double door ,4 way , IP 43 IK09 AC, 3 phase, 415 volts, TPN bus bar 200 Amps rating and earth bar & din rail complete all as specified and as directed by Engr-in-Charge. Make : Legrand Cat Pt 5077 45 or equivalent in Havelles/L&T.

Supply and fixing for MCCB, 4 pole 100A, 16KA, 415Volts complete all as specified and directed by Engr-in-Charge .

Supply and fixing MCB, SPN, 32A ,10KA.

Supply and fixing MCB, SP 40 Amp ,10KA.

Supply and fixing MCB, SP, 6-32A ,10KA.

S & F in repalcement of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB single pole 20 Amps complete all as spd and directed by Engr-in-Charge .

M&L for sub main wiring with 2 runs of 6 Sqmm and one run of 4 Sqmm of single core PVC insulated unsheathed FRLSH cable of multistranded copper conductor 1100 V grade IS-694 drawing into and including rigid non metallic PVC conduit, medium grade ISI marked not less than 20 mm with all conduit fittings & fixing accessories for concealed in wall/ ceiling or surface including one run of 4 Sqmm of single core PVC insulated unsheathed FRLSH cable as earth continuity conductorcomplete all as specified and directed by Engr-in- Charge.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, check nuts, washers of GI or steel including Cement Concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension in 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) with fair finish with 15mm thick plaster in CM 1:4 on internal surface, funnel with wire gauge of 22 gauge 8 mesh per liner inch, 80 mm thick RCC pit cover of size 320 mm x 320 mm in 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) reinforced with XPM JALLI weight not less than 4 kg per Sqm and charcoal dust and common salt all as shown in electrical plate No. 3 of MES SSR Part-I (2009) including provision of earth wire protected by 15mm dia medium grade GI pipe and watering GI pipe of 20mm bore medium grade complete including necessary excavation and earth work & connecting the earthing to an earthing test point main switch board and testing after completion complete all as specified & directed by Engr-in-Charge.

S&F in replacement of exhaust fan metallic body 300mm sweep 230 volts, single phase , AC supply with louvers with nuts, bolts and washers size of the bolts 06 inch long 6mm dia embedded in the wall complete all as specified and direted by Engr-in-Charge. Make:- Havells Cat Part No Ventil Air -DS or equivalent in Cropmton/Bajaj.

Taking down ceiling fans of any sweep and any size including cable connections and disconnecting of fan blades and removing the fan with blades to store yard and hanging ceiling fan in its original position or any other position including including it's fitting and fixtures after carrying out the repairs i.e cleaning, rewiding, greasing and filling, replacement of bearings, painting of fan with one coat of synthetic enamel paint by spraying after preparation of surface by cleaning all dust and filling cavity with filler, reassembling the fan etc including testing complete all as specified and as directed by Engr-in-charge.

Taking down exhaust fans of any sweep and any size including cable connections and disconnecting of fan blades and removing the fan with blades to store yard including it's fitting and fixtures after carrying out the repairs i.e cleaning, rewiding, greasing and filling, replacement of bearings, painting of fan with one coat of synthetic enamel paint by spraying after preparation of surface by cleaning all dust and filling cavity with filler, reassembling the fan etc including testing complete all as specified and as directed by Engr-in-charge.

Supply and fix Water heater storage type of capacity 25 litres complele all as specified and directed by Engr-in-Charge.

M/S Satyam Associates

SHEELSONS ENTERPRISES

Kunal Construction Co.

Jain Associates

Commercial Traders

SARASWATI CONSTRUCTION CO