CERTAIN EM BR WORKS REPAIR TO ROOF PLASTERING FLOORING JOINERY AND OTHER MISC WORKS OF MD ACCNS NEAR IB GATE UNDER GE NORTH BIKANER AT MIL STN BIKANER

Amount

Demolition of reinforced cement concrete to any thickness as in slabs beams incl cutting of reinforcement as reqd at site.

Demolition of reinforced cement concrete in roof floor (other than ground floors) beams staircase, landing chajja and similar work complete all as specified.

Demolition of cement concrete in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.

Demolition of cement concrete of any description not exceeding 15 cm thickness (below or above ground level) complete all as specified.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified.

Demolition of brick/stone masonry built in CM. all as specified.

Taking down shutter only exc 1.00sqm but nexc 2.00 sqm complete all as specified and as directed.

Taking down shutter & refixing in the same opening only exc 1.00sqm but nexc 2.00 sqm preserve it properly in the store and refixing in the same opening complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt ), all as specified and directed by Engineer-in Charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), all as specified and directed by Engineer-in Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips including providing and fixing new ones complete all as specified and as directed by Engineer-in-Charge.

Taking up or down steel tubing 15 mm bore with connections for cleaning for refixing or removing to store yard complete all as specified of the following description :-

Taking up or down steel tubing 20 mm bore with connections for cleaning for refixing or removing to store yard complete all as specified of the following description :-

Taking up or down steel tubing 25 mm bore with connections for cleaning for refixing or removing to store yard complete all as specified of the following description :-

Dismantling cast iron /PVC pipes fixed to walls or laid in trenches in any position.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs cleaning etc and hoisting if required reconnecting and refixing in position after cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc complete (capacity of tanks exc 250 ltr and n exc 500 ltrs)

Dismantling existing tanks, setting aside (or lowering if required)for repairs , cleaning ete. And hoisting if requeired reconnecting and refixing in position of capacity execeeding 250 ltrs and not exceeding 500 litres and removing to stores, all as specified.

Cutting through holes into through cement concrete slabs chajjas etc reinforced or other wise exc 100 sqcm but nexc 250.00 aqcm.

M & L for proning of trees up to 3 mtrs along the periphery of Building for the maintenance of area and to maintain external services incl complete removal from site complete all as specified and as directed by Engr In Charge.

M & L for uprooting of vegetation growth over building roof tops/sides of walls n exc 30 cm girth including and stacking of serviceable of metarial to a distance n exc 50 cm and cleaning side and making good of the disturbed surfaces in brick work cm 1:4 surface/area n exc 0.50 sqm complete all as specified and as directed by Engr In Charge. (Note :- For removal of vegetation if required at site rain water pipes/bends to be removed & preserved and refixed in the same laction cost included in the item).

M&L Mild steel frame work such as grills, grating etc. with ends of bars shouldered and or riveted, or forged into spikes : framed guard bars, barred iron doors, ladders, railings and similar work conforming to Fe – 290 Gde E-165 complete all as specified and as directed by Engineer-in-Charge.

M&L Mild steel Channels , framed brackets of angles or tees with web and flanges cut to shape, drilled and counter sunk for screw, including bending and welding angles , as necessary , gusset plates, riveting, etc, n exc 10 kg each brackets conforming to Fe – 290 Gde E-165 complete all as specified and as directed by Engineer-in-Charge.

M&L for TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

M&L for TMT bars 5 mm to 10 mm dia in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

M&L for reinforced cement conc M-25 design mix as in beams , cantilevers over span 1.5m landings , balconies & chajjas etc.

M&L for reinforced cement conc M-25 design mix as in slab supported on walls , beam, and columns in floors,roofs landings , balconies etc.

M&L of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, fair finished surface of concrete, all as specified .

Form work to sides and soffits of roof beams incl supports over hangs etc finished rough

Form work to edges of concrete flats, breaks ,conc railing nexc 200mm wide finished roughthick

M&L for 10 mm thick Rendering in cement mortar 1: 4 on concrete surfaces, finished Fair & even including mixing water proofing compound as per manufacturer's instns( WPC to be measured separately as supply only)

Supply only integral water proofing compound complete all as specified.

Lime concrete terracing as specified on roof

40 mm thick Brick tiles bedded in 15 mm thick cement and sand mortar (1:6) and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed by Engineer-in-Charge.

M&L for cleaning existing reinforcement bars with wire brush / rotary wire brush making the surface free from cement skin, loose particles, dirt, etc and applying rust remover ('Rustoff 100' of Sika / '8832 GM' of Pidilite or equivalent of Fosroc / Dr. Fixit) on the rebars and removing the loose rust particles after minimum 24 hours by wire brush, all as per manufacturer’s instructions, complete all as specified and as directed. Note : Mode of measurement shall be affected surface area of column, beam, slab, etc.

M&L for Jodhpur/dressed Stone slabs in sunshades, chajjas shelves, cills, landinngs, cover stones, templates, etc n exc. 2m in lenth, punched dressed on face and along exposed edges , self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4 complete all as specified.

M&L Jodhpur stone roof slabs, self faced 7.5 mm to 10 cm thick, 25 cm to 35 cm wire hoisted and set, joined and grounted in CM 1:3

M&l for brick work with Fly Ash bricks old sized straight or curved on plan exc 6m mean radius brick walls built in CM 1:6.

M&l for Brick work with subclass ‘B’ bricks, ld sized straight or curved on plan exc 6m mean radius, built in CM 1:6.

M&L half brick work with Fly Ash bricks ld sized straight or curved on plan to any radius built in CM 1:4 all as specified and directed.

M&L for Rendering 10+5 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately).

M&L for Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified.

M&L for Rendering 5mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement all as specified.

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

M&L for 25mm thick PCC type B-0 using 20mm graded crushed stone aggregate as in sub base for laying floor finishes.

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 laying floor finishes complete all as specified.

M&L for 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:3 and finished even and fair for receiving tiles on vetical surface mplete all as specified.

M&L for Non skid digital coloured tiles (square/rectengular) 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified.

M&L for glazed digital coloured ceramic tiles in dado/vertical surface (600mm x 300mm x 7 mm/450x300x7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specified and directed.

S&F 20mm thick Granite (of any type) tiles machine cut , in skirting dado laid over cement screed and jointed with grey cement slurry and pointed with white or grey cement with admixture pigment to match the shade of slab incl at moulding/bullnosing at edges and rubbing / polishing incl round finished to true surface of glazing.

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete , of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete , of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified

M&L for providing cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast complete all as specified.

M&L for factory made, 2nd class hard wood 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L Ist Class Hard Wood Glazes and skelton,(35mm)open rebated and prepaired to recive glass,gauze etc.(without sash bars) edge or framing plain, chamferd or rounded fitted with cut and mitreds beads for securing glass.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads / steel windowsin squares not exceeding 0.50 Sqm in each pane complete all as specified.

S&F 100mm long butt hinges medium weight cold rolled mild steel and fixed.

S&F MS bow handle oval type handles 150mm size.

150mm long MS tower bolts

MS sliding door bolts 250mm size, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum 6 bolts and nuts four on bolt plate and two on staple plate and fixed.

MS 300mm ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified.

S&F factory made pressed steel frame / box windows ventilators with glazed and fly proof shutters provided to size and dimensions as specified and shown on drawing no. BTD 888R sheet bo. 1/5 to 5/5 and BTD 889 sheet no 1/4 to 4/4 with and including MS frill , MS fillets pintol hinges , tower blolts, MS pressed handle Peg stay MS lugs, locking arrangements, dash through bolt where required etc including one shop coat of primer with red oxide zinc chrome complete all as spfd and as directed. Notes:- (i) PCC filling frames, glass , wire gauge and painting shall be measured and paid for seperately under fespective item of work Provn of all other items as shown on drawings shall be deemed to be included in quoted rate of this item . (ii) The qouted rate shall be deemed to be included provn of cutting holes of suitable deppth in walls for inserting lugs etc and making good dismantled portion in pcc 1:2:4 type B-0 using 12.50 mm graded crushed stone graded aggregate and CM 1:3 complete with dismantling old window of any size as directed.

M&L for Easening and resecuring of windows/doors to make them functional incl welding and all necessary repairs if required complete all as specified and as directed.

M&L for welding work in repairs n exc 2.5 cm in length complete all as specified and as directed.

M&L for welding work in repairs exc 2.5 cm in length complete all as specified and as directed.

S&F Stainless steel wire cloth o.36mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings complete all as specified.

S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site complete all as specified.

S&F Butt hinges extruded alumonium alloy with galvanised mild steel hinges pin anodisedand fixed ,type B-21 of 100mm.

Aluminium anodised barrel tower bolt of extruded section of 150mm

Aluminium handles cast type anodised of 150mm

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 litres including all accessories, all as specified (ISI Marked Double Layer).

S&F in Repair for 15 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm complete all as specified.

S&F in Repair for 20 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm complete all as specified.

M&L for 25 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm complete all as specified.

S&F 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified.

S&F 6mm thick plywwod grade BWR , type BB , fixed with screws to timber frame work.

M&L in repairs 75 mm long, Butt hinges, stainless steel, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with flap of hinge ( when open 30 mm) complete all as specified and as directed by Engineer in Charge. .

S&F in repairs 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished

S&F in repairs Hasp and staple 100 mm aluminium anodised, safety type with mild steel hinges pin including bolt to hinges plates and fixed with screws complete all as specified and as directed by Engr-in-Charge.

S&F in repairs 75 mm long, mild steel, barrel tower bolt, stove enameled black with bright bolt, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs MS steel window handle (left/right) fixed to steel windows complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs peg stay for steel windows complete all as specified and as directed by Engineer-in-Charge.

S&F Stain steel curtain rod 20mm dia mild steel chromium plated fancy type with fixing brackets, dooms and knovs at both ends as per requirement complete all as specified and as directed by Engineer-in-Charge.

S&F 75mm bore cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4

S&F 75mm bore sand cast iron waste pipe any length with or without ears laid in floor.

S&F 100mm bore sand cast iron waste pipe any length with or without ears fixed to walls

S&F100mm bore sand cast iron waste pipe any length with or without ears laid in floor.

S&F 75mm bore sand cast iron waste pipe any length with or without ears fixed to walls

S&F sand cast iron bend (any radius) 100mm bore dimnishing pieces or tapers (larger bore measured ) fitted with oval acess doors

S&F sand cast iron bend (any radius) 75mm bore dimnishing pieces or tapers (larger bore measured ) fitted with oval acess doors

S&F in repair PVC Pipe Pipe (SWR) for waste and vent pipe with or without ears, with cement joints 75 mm dia laid in trenches.

S&F in repair PVC Pipe Pipe (SWR) for waste and vent pipe with or without ears, with cement joints 110mm dia laid in trenches.

S&F in repair PVC Pipe Pipe (SWR) floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4, 75mm dia.

S&F in repair PVC Pipe Pipe (SWR) bends (any radius), disminishing pieces or tappers(larger bore measures), 110mm dia with access door.

S&F in repair PVC Pipe Pipe (SWR) bends (any radius), disminishing pieces or tappers(larger bore measures), 75mm dia with access door.

S&F in repair PVC Pipe Pipe (SWR) branch pieces ,Double (equal or unequal ) ordinary or inverted (spigot or socket type) or with parallel branches 110 mm dia.

S&F in repair CI cowls , 50mm dia

S&F in repair PVC (SWR) Couplers for 75 mm bore pipe

S&F in repair PVC (SWR) Couplers for 110 mm bore pipe

S&F in repair PVC (SWR) reducers for 110 mm bore pipe larger bore measured

S&F in repair PVC (SWR) 110 mm bore P traps

S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 50mm bore pipe

S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 100mm bore pipe

S&F cast iron cowl 50 mm bore

S&F 100mm bore CI sand cast iron branch piece single (Equal or un equal) oridinary or inverted with parallel branches

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

M&LProviding cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0.

M&L for two coats of synthetic enamel paint on new steel surfaces including preparation of surfaces over a coat of red oxide Zinc chrome primer.

M and L for sheet glass 3mm thick ordinary quality and glazing with oil putty / nails/ wooden beads in square not exc.0.5 Sqm in each pane as reqd at site and directed by Eng-in-Charge.

S&F in repair Vitreous china wash down water closet Orrisa pattern shite of size 550x440 mm including integral foot rest excluding flushing cistern and flush pipe) incl P of S trap complete all as specified.(Make Cera or equivalent)

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white excluding flushing cistern and flush pipe) incl. P or S trap complete all as specified (Make Cera or equivalent).

S&F in repair PVC seat jet for EWC with and including holding down bilts complete all as specified (Make Jaquar or equivalent).

S&F in repair Vitreous china wash basin, white flat back, size 580x450 excluding traps waste pipe fixed with brackets. (Make Cera or equivalent)

Supply and fixing in repair PVC valve less, symphonic action type, flushing cistern, low level white with inlet, ball valve, float and handle including brackets 10litres complete (Make Jaquar or equivalent)

S&F 32mm bore waste fittings brass chromium plated for wash hand basin etc with long screwed shand and flynuts etc. (Make Jaquar or equivalent)

S&F in repairs pillar taps cast copper alloy with capstan head, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe and fixed. (Make Jaquar or equivalent)

S&F in repair overhead shower with arm 225 mm with flange of cast copper alloy chromium plated fixed. (Make Jaquar or equivalent)

S&F in repair Stop valve brass fancy type concealed type stop valve chromium plated with long shank and complete screwed for iron pipe.(Make Jaquar or equivalent)

S&F in repair bib taps chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed (Make Jaquar or equivalent)

S&F in repair bib taps Long Body chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed (Make Jaquar or equivalent)

S&F in repair Towel rail 600mm long of cast copper alloy, chromium plated, fixed in repair complete all as specified and directed by Engineer-in-charge.

S&F for peg set of Six of best quality complete all as specified.

S&F PTMT glass shelf with and ans including chromium plate brass screws and wooden cleats complete all as specified and directed by Engineer-in-charge. (Make Jaquar or equivalent)

S&F Chromium plated stop cock/Angle Valve, with crutch or butterfly handle screwed down for iron pipe or brass ferrule fancy type , CP 15mm dia. (Make Jaquar or equivalent)

S&F PVC connection 15mm size with PTMT nuts of length 450mm. (Make Jaquar or equivalent)

Stop valve cast copper alloy screwed down , high ressure wit crutch or butterfly handle , screwed both ends for iron pipe or for unions or 15mm dia all as specified. (Make Jaquar or equivalent)

Demolition of lime concrete of roof any description and in any position not otherwise specifically provided.

Dismantling existing terrazzo dado/flooring or tiles in bath, WC and kitchen etc complete all as specified.

Dismantling of stone slabs in roofs, chajjas, suspended floors, landings etc only thickness jointed in any mortar complete all as specified.

Dismantling of brick tiles or terracing tiles single layer on roofs complete all as specified.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement base paint white or tinted over and including a coat of alkali resistant priming paint complete all as specified.

Preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over a coat of chalk whiting complete all as specified and as directed by Engineer-in-Charge.

Preparing surfaces of newly plastered or unplaster surface and applying two coat of white wash on ceiling

M&L for preparing old plastered or unplastered surfaces of walls and applying one coats of cement base paint white or tinted over and including a coat of alkali resistant priming paint complete all as specified.

Preparation of old plastered or unplastered surface or wall and applying one coats of distemper oil emulsion, white or tinted over a coat of chalk whiting complete all as specified and as directed by Engineer-in-Charge.

Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc complete all as specified and as directed by the Engr-in-Charge.

Taking down of unserviceable DBs/switch fuses/changeover in sheet steel enclosure complete with MCBs/Fuse/grips any capacity and removing from site and making good disturbed surface of wall, floor etc. Taking after disconnecting all cable complete all as specified and as directed by the Engr-in-Charge.

Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid PVC concealed conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 141 here-in-before but socket point on the same board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No 141 here-in-before but socket point on independent board complete as specifed as directed by Engineer - In - Charge

All as per item No 141 here-in-before but cable 2.5 Sqmm for 15 Amps switch socket outlet on independent board complete as specifed as directed by Engineer - In - Charge

All as per item No 142 here-in-before but one light point controlled by two 02 way switch complete as specifed as directed by Engineer - In - Charge

S&F Switch piano type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge S

S&F Switch piano flush type, Single pole 15 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F Switch piano type, Single pole 5 Amps, two way ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F Socket outlet 2 in 1, 3 pin, 5A ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F switch socket combination 5 in 1, 5/16 amp flush type fixed on laminated sheet top cover (laminated sheet top cover is including in point wiring).

S&F Single pole and neutral enclosure witha two pin and earth plug and socket complete with one single pole MCB 10 Amps complete all as specified and as directed by Engineer-in-Charge .

S&F Ceiling rose PVC/poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and as directed by Engineer-in-Charge.

S&F Bell push, flush type, 5 ampcomplete all as specified and as directed by Engineer-in-Charge.

S&F Buzzer, Ding Dong AC. 230 volts, single pole all as specified and as directed by Engineer-in-Charge.

S&F Lamp holder insulated body with back plate for conduit/casing capping fittings complete all as specified and as directed by Engineer-in-Charge

S&F MCBTPN DB 4 way verticla type 440 V 3 phase with rated bus bar 250 amps , double door tyoe suitable for MCCB as incommer and MCBs as out going double door type grouted in wall with fixing attangement complete all as specified and as directed by Engineer-in-Charge. Make:- Legrand Cat No.-5077 50 or euivalent in C&S/ Havells.

S&F Sheet metal enclosure double door type powder coated MCBDB SPN 8 ways fitted with neutral link earth bar , din rail ,200 Amps rated bus bar 230 volts conforming to IS 13032-1991 complete all as specified and as directed by Engineer-in-Charge.

S&F MCB SPN 5-32 Amps 240 volts, breaking capacity 16 KA omplete all as specified and as directed by Engineer-in-Charge.

S&F MCB SP 5-32 Amps 240 volts, breaking capacity 10 KA omplete all as specified and as directed by Engineer-in-Charge.

S&F MCCB 63 Amps, 4 pole 415 volts, fixed ype breaking capacity 16 KA complete all as specified and as directed by Engineer-in-Charge.

Taking down ceiling fan, sealing cable end, dismantling blades and removing fan and blades to store for Painting of ceiling fans complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. (M & L) and fixing ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan, writing MES No. etc complete all as specified and directed by engineer-in-charge.

Taking down Exhaust fan, sealing cable end, dismantling blades and removing fan and blades to store for Painting of ceiling fans complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. (M & L) and fixing ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan, writing MES No. etc complete all as specified and directed by engineer-in-charge.

Removing and refing water heater storage type puff insulation type of 25 ltrs capacity and 1500 watts BEE star rated -5 with glass line inner shell with Hot & cold pipe , water connection type, electric connection and necessary fixing arrangements complete all as specified and as directed by Engineer-in-Charge

S&F Sub main wiring with 2 core, multi-stranded PVC insulated cable unsheathed 1100 volts grade with copper conductor of size 6 sq mm drawn PVC concealed conduct including earth continuity conductor cable of size 04 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.

N.K. CONSTRUCTION COMPANY

SHREE GURU NANAK CONSTRUCTION COMPANY

JAGDAMBA CONSTRUCTION COMPANY

SUBHAM ENTERPRISES

durga construction company

M/S BUDHRAM BISHNOI