PROVN OF REPAIR SHED FOR VEHS KOTA STONE AT FLOORS OF BLDG NO T 163 04 X HARDSTANDING FOR TURNING PADS OF VEHS NEAR BLDG NO OPT 131 UNDER GE GANGTOK

Amount

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

M & L for Removing excavated materials (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m the starting point complete all as specified and as directed.

Returning, filling in, including spreading levelling watering and well ramming in layers not exceeding 25 cms in thick as in soft/loose soils complete all as specified and directed.

M&L for PCC 1:4:8 type C-2 (using 40mm graded stone aggregare) as in foundation filling & mass concrete completed.

M&L RCC (Nominal mix) 1:1.50:3 using 20mm graded stone aggr as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed

M&L mild steel TMT Bars 10mm dia and over cut to length bend to shape required including cranking bending spirally for column, hooking ends & binding with and including mild steel mild steel wire (annealed not less that 0.90 mm dia or securing with chip).

All as per item No 07 here-in-before but 5mm dia and over upto and including 10 mm dia in stimup, spacer and binders.

M&L for RCC (Nominal Mix) 1:2:4 foundation, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. complete all as specified and as directed

M&L for formwork to sides of concrete foundations, plinth beams for rough finished surface of concrete, complete all as specified and as directed

Material and Labour for precast cement concrete solid block masonry Type C1 (1:3:6) using 20 mm graded aggregate as per IS 383 exc 10 cm in width and setting in cement mortar (1:6) complete all as specified and as directed by the Engr-in-Charge.

Material & labour for rendering 15mm thick on block concrete masonry walls in CM 1:6, finished even and smooth without using extra cement complete all as specified.

M&L for rendering 20mm thick in cement mortar 1:4 in two layers of 10mm each using WPC in finishing layer on brick or concrete surfaces finished even & smooth (WPC for finishing layer will be paid seperately as supply only).

Supply only integral water proofing compound.

M&L Preparation of newly plastered surfaces of walls and applying three coat of white wash on new surfaces of walls all as specified and directed.

M&L Preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of suitable primer on new surfaces of walls all as specified and directed.

M&L for mild steel rolled sections conforming to Fe-290 (Gde E-165) as in main and cross beams, hip and jack rafters; purlins where connected to common rafter and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile stregth of 550 mpa as in roof covering fixed with self tapping screws complete all as specified and directed

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and applying neat cement slurry, etc complete.

M&L for 100mm thick PCC concrete type C2, 1:3:6 (40mm graded aggregate) in flooring complete all as specified and directed.

M&L for 50mm thick PCC concrete type B- 1, 1:2:4 (20mm graded aggregate) in flooring complete all as specified and directed.

M&L for providing Plastic dividing strips, 1.5mm thick and 48 mm wide ditto

Material and labour for PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in coping including weathering slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L for preparation of new steel surface of any description over 10cm in width or girth, not otherwise desribed and applying two coats of synthetic enamel paint over a coat of red oxide Primer.

Material & labour for hardcore of gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface using broken stone or boulders.

M&L for 75mm thick PCC type C-2 (1:3:6) using 40 mm graded agg in plinth protection path/hardstanding finished cement concrete surfaces fair and even all as directed by Engineer-in-Charge.

Material and labour for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in surface channels and drains complete all as specified and as directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds mitered/ stopped ends etc.

M&L Screed Bed or Bedding layer of mortar 20mm thick for laying tiles complete all as specified and as directed.

M&L Rendering 10mm thick in cement Mortar 1:4 plastered surfaces finished rough to received wall tiles complete all as specified and as directed.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dadoand pillar laid over cement screed and jointed complete all as specified and directed.

M&L for chequred cement concrete tiles of size 200mm x 200mm x 25 mm/ 300 x 300mm x 25 mm thick as in pavement/footpath/trade/riser, set and jointed in neat cement slurry and pointed with grey cement and pigment laid over and including screed bed/bedding layer of 15mm thick in cement mortar (1:4) complete all as specified and as directed

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15 deep and getting out soft/loose soil completed.

M&L for excavating over areas, in soft loose soil n exc 1.5 deep and getting out etc all as specified.

Materials and labour for 150mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub-base of floor etc complete all as specified and as directed by the Engr-in-Charge.

Material and labour for 100mm thick PCC 1:2:4 type B2 (using 40mm graded stone aggregate) as in sub-base of floor etc complete all as specified and as directed by the Engr-in-Charge.

Excavation in post holes in soft/loose soil each n.exc 05 cum, getting out returning filling in and ramming earth or broken rubble mixed with earth around, in layer not exceeding 25cm complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 (40mm graded stone aggregate) as in foundation, filling, mass concrete etc completed.

S&F of Mild steel works as in posts, struts, etc in fencing including cutting tops to shape as directed drilling holes notching for wire etc, flat iron fillets/horizontal bars etc including necessary drilling, welding, bolting or riveting etc complete.

S&F of Mild steel screw bolts (Machine Made) with hexagonal heads, bolts washers etc (5 to 10mm dia) length of bolt exc 5cm and n.exc 10cm long completed.

S&F Mild steel round bars grade Fe290 10mm dia and over dia cut to length, bent to shape required including cranking, bending spirally, hookings/ends and binding or securing with clips completed.

S&F Mild steel flat iron of size 40 x 6mm conforming to Fe 290 including necessary drilling and fixing with nuts & bolts complete all as specified and as directed (Note : MS nuts & bolts shall be measured and paid separately)

Fixing only chain link fencing fixed to any type standard rail, staining bolts etc. completed.

Supply only chain link MS galvanised fencing of mesh size 50 x 50 weight not less than 2.57 Kg/Sqm and completed as specified and as directed.

S&F Galvanished, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm barbs at 75mm spacings and straining and fixing to any type of standard rails strainging bolts, including, securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc as directed (each line wire to be measured).

M&L for two coats of synthetic enamel paint over a coat of red oxide primer to surfaces of any description n.exc 10cm in width or grith incl preparation of new steel surfaces complete all as specified and directed.

Dismantling plain or corrugated sheeting, any gauge, thickness all as specified.

Dismantling of timber in scantling 40 sqcm and over in section in any position in unframed work all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) of area exc 1.5 sqm but n.exc 4.0 sqm complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) of area n. exc 1.5 sqm complete all as specified and directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), removing from the Sites and rubbish off the Premises complete all as specified and directed.

Dismantling of wall and ceilling boards (fiber pulp insulation etc) or insulation boards.slabs/blankets any thickness including cover fillets complete all as specified and directed.

M&L framed work as in doors gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete.

M&L for preparation of previously treated steel surface of any description not otherwise described n exc 10cm width or girth and applying two coats of black japan paint over a coat of red oxide complete all as specified and directed by the Engr-in-Charge.

Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheets of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and directed.

M&L 15mm thick rendering plaster on fair faces of conc faces/brick faces smooth without extra cement in CM 1:4 complete all as specified and as directed.

M&L for preparation of new plaster surfaces and applying priming plastered and other surfaces with alkali resistance priming paint and applying two coats of acrylic washable distemper on walls as specified and directed.

M&L Vitrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match completed.

M&L Vitrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surface etc set and jointed in neat cement slurry and pointed in white or coloured cement to match completed.

M&L 15mm thick screed bed or bedding layer of cement plaster 1:4 incl finished all as specified.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match,over and Incuding 15mm thick screed bed with CM 1:6 complete in floor for receive the tiles complete all as specified and as directed.

M&L glazed ceramic coloured tiles 300 x 200mm x 7mm thick on vertical surfaces such as skirting, dados, set & jointed in neat cement slurry & pointed in colour cement to match complete all as specified and as directed.

M&L Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing with Powder Coating (Minimum thickness of power coating 50 micron complete all as specified and as directed.

M&L Anodised aluminium window and ventilator shutters, fixed type without sash bar aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips rubber packing, anodised aluminum snap beading, screws with powder coating (minimum thickness of powder coating 50 micron complete all as specified and as directed.

S&F 5.50 mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufactures complete all as specified and as directed.

S&F 3mm thick, sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and as directed.

S&F Mild steel butt hinges 75mm long, medium weight, cold rolled, complete all as specified and directed.

S&F Extruded aluminium alloy handles 100mm long, fabricated type anodised complete all as specified and directed.

S&F Aluminium anodised barrel tower bolts, 100 mm long of extruded section complete all as specified and directed by the Engr-in-Charge. .

Supply and fix in repair vitreous china, white colour, flat back, wash hand basin of size 63 x 45 x 22.5cm fixed with brackets , including providing 32 mm dia PVC waste pipe , 32 mm bore CP waste coupling and making all necessary connections complete as directed.Make : Cera Cat No. S2040104 or equivalent of make as specified in List of makes.

S&F Vitreous china wash down water closet pan size 520mm x 360mm x 390mm with 'P' & 'S' trap, incl fixing bolts, plastic water closet seat cover, closed pattern with flat bottom, and mild steel chromium plated aluminum anodised hanging device, making all necessary connections and making good to floor all as specified and directed by Engr-in-Charge.

S&F Vitreous China urinals, bowl type (back or comer wall type), complete including providing and faing plugs, bedding urinal against wall in cement mortar 1:2. securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistem with brackets, flush pipe, grating and Union for discharge pipe (Exclusive of fbing supply pipe to flushing cistern, trap and waste pipe complete all as specified and as directed.

M&L for 15 mm bore steel tubing medium grade galvanised with all Sittinged complete to walls & laid in floors complete all as specified and directed.

M&L for 20 mm bore steel tubing medium grade galvanised with all fittinged complete to walls & laid in floors complete all as specified and directed by the Engr-in-Charge

S&F for 15 mm bore fancy type pillar tap cast copper alloy with capstan heads chromium plated screwed down high pressure with or without letter hot or cold with long screwed shanks and fly nuts screwed for iron pipes and fixed complete all as specified and as directed

S&F CP centeral hole basin mixer extended costed spout with 450mm braided hoses complete all as specified and directed.

S&F for 15 mm bore two way bib taps long body cast copper alloy chromium plated, wall Banges and aerator with all accessaries complete all as specified an directed

S&F 15 mm dia stop cock /concealed stop cock cast copper fancy type chromium plated alloy screwed down high pressure with clutch or butterfly handle served both ends for iron pipe or for union compete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all respect as specified.

S&F Aluminium anodised tubular towel rail, 20mm dia, D type 60cm long between flanges etc complete all as specified.

S&FSoap dish, vitreous China white, approximate size 160x 160x 90mm. any type, foxed to plugs with chromium plated brass screw complete all as specified and directed

S&F of PVC 'P' or 'S' trap 110mm bore complete all as specified and directed by the Engr-in-Charge.

S&F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by the Engr-in-Charge.

M&L Concrete bed to drain pipe of 110m m dia including packing under and haunching against the side or pipe after they are laid and tested in complete all as specified and directed by the Engr-in-Charge.

S&F for 40 mm dia GI pipes Heavy Class for water pipe line complete all as specified directed

S&F 4 mm thick (E- board) Non asbestos fibre cement building boards fixed or laid/ inserted to Gl snap grid framework with screws fixed in ceiling flat or sloping including Gl frame work for ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended fromsoffit at approx 900 mm centre to centre with G cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting levelfixed to roof slabs by means ofceilling cleats made out of G.I.flat 40 x 3 mm size 60mm longand expansion hold fasteners 12.5mm dia. 40mm longcomplete all as specified and directed

S&F Solid PVC door frame of size 50mm x47mm made out of 5 mm plain colou PVC sheet renforeced with MS square tube, suppling & foxing in opeming as sper specofication & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bootom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rails on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the stiles & rails with suitable PVC sheet beading & joined together with solvent cement suppling & fixing in the frame at site as specification & drawing

E/M Portion Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, inlcuding fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc removing materials for taking credit and making good disturbed surfaces of walls, floors etc complete all as specified and as directed.

Taking down carefully unscrewing min DBsor switch etc.

M & L for point wiring with 1.5 Sqmm PVC insulated unsheathed single core stranded copper conductor (FRLS) Cable of working voltage 1100 Volts grade conforming to IS-694 pt-I & II of 2000 drawn in and including 25 mm size PVC casing caping (Double lock) with all casing capping fittings & accessories with 1.60 mm thick pressed steel or mild steel sheet sunk box covered with 3 mm thick backelite sheet fixed with brass screws & cup washers including 1.5 sqmm PVC insulated unsheathed single core stranded copper conductor (FRLS) cable as earth continuity conductor connected to main switch / DB's or common earth dolly complete for for light point/ fan point/ exhaust fan point/ call bell point controlled by one No 5/6 Amp one way switch complete all as specified and directed.

All as per item No 94 one switch socket outlet point 5/6 Amps on Independent board complete all as specified and directed.

All as per item No. 94 above but for one socket outlet of 15 Amps fixed on independent board with 2.5 Sqmm multistranded copper conductor wire FRLS PVC insulated and 2.5 Sqmm copper conductor wire FRLS PVC insulated using as earth wire complete all as specified and as directed.

S&F in repairs switch piano flush button,single pole, one way, 5 amps complete all as specified and as directed.

S&F in repairs ceiling rose, PVC/polycarbonate insulated body, 3 terminal and 240 volts, ISI marked complete all as specified and directed

S&F in repairs switch socket combination, 2 and 3 pin, 5/6 amps, multipurpose, flush, non shutter, non inter locking type, 230 volt flush type, white/ivory finish with two fixing hole including suitable gang box complete all as directed

S&F in repairs switch socket combination, 2 in 1, 6 pin, 5/6 Amps and 15/16 Amps, multipurpose , flush, non shutter, non inter locking type, 230 volt flush type, white/ivory finish with two fixing hole including suitable gangbox complete all as directed.

S&F in repairs lamp holder angular/straight insulated body, with back plate suitable for batten fittings, white/ivory finish complete all as directed.

S&F in repairs LED lights fitting 1x 18/20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed (Make : Crompton Cat No CCS-103-20-65-SL-DP-NWH or equivalent approved make as listed in PS)

S&F only decorative 2 feet LED tube light fittings 1x10W, 220V, AC mirror type including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F LED light fitting 1x 9W/ 1x10W bulk head luminairies including LED light driver holder connecting up with three core flexible copper flexible copper conductor cable of suitable size complete all as directed.

Supply and fixing round shape 12 watts, 220volts AC recessed type with high efficiency PMMA diffuser soft grade free light complete with dirvers, holders, LED Lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

S&F Exhaust fan made of sturdy Engineering plastic body complete with louvers shutter, voltage 230V, 50Hz copper winding of sweep 150mm complete all as specified and directed by Engr-in-Charge.

Supply, installation, testing and commissioning of electric water heater, storage vertical type, BEE 5 star rated, 25 Ltr capacity 230 volts AC, 50 Hz comprising of high wattage heating element for instant heating, extra thick SS inner tank of superior 304 grade, rust & sock proof ABS outer body, non-ferrous pressure plate with & including provision of Pressure relief valve and grouting bolts suitably flushed to wall or any other surface including electric connection with 3 core PVC insulated, sheathed, stranded copper conductor cable/flexible chord complete all as specified and as directed.Make Model No GHWAMGTWH025 of Havells or eqv as approved make.

S&F MCB DB SPN 8 Ways double door, IP-43, IK-09 with metal door, rated bus bars, earth bar, neutral links complete incl blanking plates as required & fixed flush to wall/other surface complete all as specified and as directed.

S&F in repairs MCB single pole & neutral 40 to 63 Amps, 240 Volts, 10 KA rapturing capacity, 'C' Curve complete all as directed by Engineer-in-charge.

S&F in repairs MCB single pole 6 to 32 Amps, 240 Volts, 10 KA rapturing capacity, 'C' Curve complete all as directed by Engineer-in-charge.

Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connected with galvanised iron/steel earth wire of 4mm dia by means of bolts, nuts, check nuts and washers made outof galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part-I and earth wire protected by galvanized pipe light grade 15mm bore and connected to VTPN DB/SPN DB including neccessary earthwork and excavation in any type of soil, GI light grade 20mm bore watering pipe with funnel and wire mesh, PCC 1:2:4 type B1 chamber with 40mm thick RCC 1:2;4 type B1 design mix cover slab with 6mm dia MS bars at 100mm c/c both ways with MS hook 6mm dia MS bars etc complete all as specified and as directed including testing on completion.

Supply and fix stop valves, cast copper alloy, screwed down, high pressure with clutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 15mm complete all as specified and directed by Engr-in-Charge.

Supply and fix stop connection 15mm size with PTMT nut of length 750mm, complete all as specified and directed by Engr-in-Charge.

Supply, Laying, jointing & testing 1100 volts grade, XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured LT electric power under ground cables conforming to IS 7098(Part-I)-1988, heavy duty with aluminium stranded conductor laid in trenches or passing through pipe of cross sectional area 16 sqmm 2 core with all fixing & connecting accessories complete all as specified & as directed.

Supply and laying of DWC HDPE pipe, ISI marked in trenches or in cable ducts or fixed on walls, using clamps along with all accessories like socket, bend, couplers etc confirming to IS 14930 Part-II complete with fittings and cutting, jointing etc of size 50mm outer dia complete all as specified and as directed by Engr-in-Charge.

S&F Rotational moulded polyethene water storage tanks 500 ltrs, ISI Mark, multilayer constraction (Cylindrical vertical with close top) hoisted and fixed in position incl supply and fixing of 25mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe of having weight not less than 455 gms including connection complete all as specified and directed.

M&L for 25mm dia steel tubing medium grade galvanised with all fitting fixed complete to walls and ceiling or floor complete all as specified and as directed.

Supply and fix 25mm bore gun metal valve, ISI marked with iron wheel head screwed both ends for GI pipe complete all as specified and as directed.

Material & Labour for point wiring with 1.50 Sqmm (nominal cross sectional area) PVC insulated (FRLS) unsheathed single core multi stranded copper conductor cable of working voltage 1100 volts grade conforming to IS-694 Pt I & II of 2000 drawn through and including non metallic rigid PVC medium grade conduit and conduit accessories (ISI) Marked concealed in wall/fixed to roof, ceiling etc., including provision of 1.5 Sqmm (nominal cross sectional area) PVC insulated (FRLS) unsheathed single core multi stranded copper conductor cable as earth continuity conductor, fabricated sunken terminal box made out of 1.60mm thick sheet steel painted, concealed in walls, with 3mm thick bakelite/PVC sheet ISI marked top cover with brass chromium plated screws and cup washers for housing switches, socket outlets, fan regulators etc., connected to main switch / DBs or common earth dolly for light point/ fan point/ exhaust fan point/ call bell point/ controlled by one switch 5/6 Amp one way complete all as specified and directed. Note: Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

All as per item No.119 here-in-before but for one socket outlet/metal clad socket of 15 Amps fixed on independent board with 4 Sq mm multistranded copper conductor wire FRLS PVC insulated and 4 Sq mm) copper conductor wire FRLS PVC insulated using as earth wire complete all as specified and directed by Engineer-in-Charge

Supply and fixing LED flood/bay light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection,with impact and corrosion resistant complete with driver and lamp

M/S S. S CHETTRI AND SONS

M/S ANIL KUMAR THAKUR

Phurba Wangdi Sherpa

BIJAY MITTAL

NISHA CONSTRUCTIONS

DHARMINDER SINGH

KARMA TSETEN BHUTIA