8404 REPAIRS TO FENCING, GATE, DRAIN, FOOTPATH, COMPOUND WALL, HARDSTANDING AND CERTAIN MISC WORK INCLUDING EM INSTALLATION AND AREA UNDER AGE BR-III SOUTH PUNE

Amount

Demolition of cement concrete in ground floors and paving not exc 15cm thick (below or above ground level) un-reinforced.

Demolition of Reinforced cement concrete of any description and in any position (below or above ground level) complete all as specified.

Dismantling stone slabs and tiles including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Demolition of brick work or stone/boulders masonry built in Cement Mortar complete all as specified and as directed.

M&L for 150mm thick Hard core, broken to gauge exc 63mm and n. exc 100mm broken stone/boulders complete all as specified and as directed.

M&L for Plain Cement concrete, 1:4:8 mix, type D2, (using 40 mm graded crushed stone aggregates) 75mm thick as in sub base complete all as specified and as directed .

M&L for Chequered cement concrete tiles of 30cmX 30cm X 25mm thick, rubber moulded glossy finish set, jointed & pointed in neat cement slurry in floors ( with white cement & pigment) laid over and including 20mm thick screed bed in CM 1:6 complete all as specified & as directed.

M&L for precast concrete interlocking paver blocks glossy finish with approved shape and size conforming to IS-15658-2006,60mm thick, M-30 grade with white cement and pigment laid over & including 75mm thick stone dust/grit complete all as specified & as directed.

M&L for PCC nominal mix 1 : 1½ : 3 (using 20mm graded crushed stone aggregate) as in paving complete all as specified & as directed.

M & L for Finishing surface of concrete roads, pavements, by brooming complete all as specified & as directed.

M & L for forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'A', complete all as specified & as directed.

M & L for Precast Cement Concrete block of type C1, (1: 3 :6 mix) (Using 20 mm graded crushed stone aggregates) set in Cement Morter 1:6 complete all as specified & as directed.

M&L for rendering, 15mm thick, in CM (1:6) finished even and smooth without using extra cement complete all as specified and as directed

M & L for Reinforced concrete pipes 300mm bore, class NP2, laid and jointed complete with collars complete all as specified & as directed.

M & L for Reinforced concrete pipes 450mm bore, class NP2, laid and jointed complete with collars complete all as specified & as directed.

M&L for PCC 1:4:8 type D2 using 40mm graded aggregate as in bed to drain pipes including forming cradles for 300mm bore RCC hume pipe complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 using 40mm graded aggregate as in bed to drain pipes including forming cradles for 450mm bore RCC hume pipe complete all as specified and as directed.

M&L for Plain cement concrete 1:3:6 type C-2 (using 20 mm graded crushed stone aggregate) as in surface channels and drains (including necessary form work) complete, all as specified and directed.

Excavation in trenches, not exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. not exc 10 sqm on plan and getting out in Soft/disintegrated rock complete all as specified and as directed.

Excavating in trenches, not exc 1.5 m wide and exc. 1.50m depth but not exc 3 m in depth; for foundation, etc. not exc 10 sq m on plan and getting out in Soft/ disintegrated rock complete all as specified and as directed.

M&L for high strength deformed TMT bars 10mm dia and over of grade Fe 500 as in reinforcement, cut to length, bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

M&L for high strength deformed TMT bars 8mm dia of grade Fe 500 as in reinforcement cut to length, bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.9mm dia all as specified and as directed.

S&F MS TMT bars 6 to 8mm dia and over upto & including 10mm dia, cut to length, bend to shape as required including cranking, bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacers, binders complete all as specified and as directd.

M&L for RCC(nominal mix) Type B1, 1:2:4(20 mm graded aggregate), as in foundation, including rafts, footings, foundation beams, plinth beams, bases of coloums etc complete all as specified & as directed.

M&L for RCC(nominal mix) Type B1 1:2:4(20 mm graded aggregate), as in columns, piers, pillars posts, and struts complete all as specified & as directed.

M&L for RCC(nominal mix) Type B1 1:2:4 (20 mm graded aggregate), as in beams, coping, cantilever, bressummers, lintels, over 1.5m span complete all as specified & as directed.

Use and waste of form work to sides of concrete foundations, footings, bases of columns,Plinth beams etc with rough finished surfaces of concrete flat complete all as specified & as directed.

Use and waste of form work to sides of square, rectangular or polygonal to sides of pillars, posts, struts, piers, columns with rough finished surfaces of concrete complete all as specified & as directed.

Use and waste of form work to PCC bands not exc 20 cm wide for rough finished surfaces of concrete flat complete all as specified & as directed.

M&L for rendering 15mm thick in CM 1 : 4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified & as directed.

M & L for 20 mm thick rough cast plaster in CM (1:6) complete all as specified & as directed.

M & L for preparation new plastered surfaces of walls and appplying two coats of cement base paint complete all as specified & as directed.

M & L for broken glass in coping on top of wall in CM 1 : 3 complete all as specified & as directed.

Returning, filling in, (Soft disentegrated rock) including spreading, levelling, watering & well ramming in layers not exc 25cm complete all as specified & as directed.

Removing excavated materials upto a distance not exceeding 50m & depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion in cement concrete and making good disturbed ground complete, all as specified and directed.

Dismantling of wrought or MS work of any description etc complete all as specified and directed.

Dismantling of fencing wiremesh any type complete all as specified and directed.

Excavation in post holes each not exc 0.5 cum and getting out in Soft / disintegrated rock, including returning fillling in and ramming earth or broken rubble mixed with earth around in layers not exc 25 cm, watering and removing surplus soil to a distance not exc. 50 cm and making good surfaces in post holes complete all as specified & as directed.

M & L for PCC (1:3:6 mix), type C2 (using 40 mm graded aggregates) in foundation of fencing posts complete all specified & as directed.

Supply only Chain link fencing of any mesh, size and gauge complete all as specified & as directed.

Fixing only chain link fencing of any mesh, size, and type to any of the standard, Straining bolts etc including provision of binding wire complete all as specified & as directed. (Note :- Line wire shall be measured & paid seperately.)

Supply only MS round bars 8 to 10mm dia as in line wire, for chain link fencing complete all as specified & as directed.

Supply and fixing MS work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified & as directed.

Supply and fixing Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm n exc 10cm long and 16 to 20 mm dia of neck including welding complete all as specified & directed by Engineer-in-Charge.

Supply and fixing MS framed work such as framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc.with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified & directed by Engineer-in-Charge.

Supply and fix in repair Mild steel, plain, black sheet 1.25mm thick, in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description n.exc 10cm girth or width not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M & L for applying two coats of Synthetic enamel paint over a coat of red oxide primer including preparaton of new untreated steel surfaces of any description exc 10 cm width or girth, complete all as specified & as directed.

Dismantling plain or Corrugated, semi corrugated, etc sheets of any type in roof covering complete all as specifed and directed.

S&F Prepainted galvalume aluminium zinc coating GI based , corrugated steel sheet 0.50 thick of any colour as in roof covering / cladding to wall fixed with self tapping screws complete all as specified & directed.

S&F Prepainted galvalume aluminium zinc coating GI based , Plain steel sheet 0.50 thick of any colour as in roof covering / cladding to wall fixed with self tapping screws complete all as specified & directed.

Demolition and breaking of drain pipes AC /CI/PVC set in cement mortar or adhensive all as directed of 75mm to 110 mm dia complete all as specified and as directed.

S&F PVC (SWR) pipes 110mm bore, single socketed in any length with rubber ring joints fixed to wall / ceiling or laid in trenches complete all as specified and as directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410-W(Gde-E- 250) quality- A complete all as specified and as directed.

REKHA ELECTRICALS

Raj Construction Company

M/s Omkar Associates

Agarwal Agencies

ANIL CONSTRUCTION CO.

J P ASSOCIATES

M/s.BAJRANG CONSTRUCTION

L.K.R.TIWARI CONSTRUCTION

R k construction