SPECIAL REPAIR TO BLDG NO KND-29 AT JUTOGH MT AND OTM BLDG NO T-4 ADH OR LINE UNDER GE (I) JUTOGH

Amount

Demolition of cement concrete (un-reinforced) in ground floor and paving n. exc 15 cm thick below or above ground level, complete all as specified and directed.

Demolition of brick work or stone boulder masonry built in cement mortar, complete all as specified and directed.

Dismantling of RCC shelf other than ground floors and similar suspended works, complete all as specified and directed.

Taking down cement plaster of any description on brick wall surfaces etc including raking out joints hacking for key , scrubbing down down with water etc., complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M&L for brick work with sub class 'B' bricks (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified and directed.

M&L for stone masonry random rubble, well bonded, bedded and solidly hearted in CM 1:6 in retaining walls abutments brought up to courses complete all as specified including necessary provn of weep holes etc., complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick built in CM 1:4 with sub class 'B' bricks of class designation 10 (minimum compressive strength of brick 100 kg/Sqcm), complete all as specified and directed.

M&L for rendering 10mm thick in two layer on stone masonry surfaces or surfaces other than fair face of brick work in CM 1:6, finishing surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15mm thick CM 1:4 on fair face of brick, hollow block, concrete surface finished even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for non skid ceramic tiles (coloured) 300x300x 7 to 8mm thick (square/rectangular) area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:6), complete all as specified and directed.

M&L for 1st quality, glazed ceramic coloured tiles 350x250x 7mm/450x350x 7mm thick on vertical surface of walls with neat cement slurry @ 3.00 Kg / Sqm incl pointed in white cement with pigment to match the shade of tiles, over and incl screed bed 10mm thick 1:4, complete all as specified and directed.

M&L for coloured ceramic cladding/ elevation tiles joint free in vertical surfaces of size 350x250x7-8mm/ 450x300-350x7-8mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick backing coat in cement mortar 1:4, complete all as specified and directed.

M&L for non skid ceramic tiles 7-8mm thick coloured (Square/rectangular)each tiles exceeding 0.18 sqm but n exc 0.38 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed as in CM 1:6, complete all as specified and directed.

M&L for non skid ceramic tiles 7-8mm thick coloured (Square/rectangular) each tiles exceeding 0.18 sqm but n exc 0.38 sqm in vertical surface such as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick backing coat in cement mortar 1:4, complete all as specified and directed.

M&L for RCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in shelves/ slabs/ beam/ columns/ foundation and like with and incl use and waste of necessary form work complete all as specified and directed.

M&L for MS TMT Bars 10mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for MS TMT Bars 8 mm dia cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified and directed.

Taking down chawkhat or frame with (without taking of shutters from the frames) exc 1.50 sqm but n. exc 4sqm complete all as specified and directed.

All as per Srl Item no 20.00 above but n.exc 1.5 sqm, complete all as specified and directed.

S&F in repair 2nd class HW Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F 30mm flush shutters, solid core construction, with block board core and plywood face panels, commercial types on both sides incl teak wood beading around the shutters complete all as specified and directed.

S&F 2nd class hard wood 30mm thick made glazed and skeleton shutters factory made open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass, etc, size of members of shutters as specified in SSR Part-1, Section-8, clause 8.24 (a) complete all as specified and directed.

S&F in repair factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length and making it good to match with existing surface, complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: Stainless steel butt hinges and necessary SS screws shall be measured and paid separately.

S&F box type of steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

S&F box type of Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed.

S&F box type of Steel ventilators, with top hung shutter including hinges steel peg stay, complete all as specified and directed.

S&F sheet glass ordinary quality 4 mm thick glazing in square/ rectangle n.exc 0.50 sqm each pan with oil putty or aluminium beads fixed to steel and wooden of any height including necessary scaffolding and T&P required to complete the work complete all as specified and directed.

S&F sheet glass 4.00 mm thick figured glass pin headed type and glazing with oil putty or wooded bead built in squares not exceeding 0.5 sqm in each pane, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, with ridge, gutters, etc, any gauge, and thickness incl Nainital pattern roof covering, fixed with J/L hooks or coach screws complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges ,flashing, eaves board, valley gutter etc, fixed all as per manufacturer's instructions, fixed with self tapping screws, at site with suitable arrangement as required, complete all as specified and directed.

S&F for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall,facia, ridges ,flashing, eaves board, valley gutter etc, fixed all as per manufacturer's instructions, fixed with self tapping screws, at site with suitable arrangement as required, complete all as specified and directed.

Dismantling of boarding of any description and in any position, complete all as specified and directed.

S&F 6mm thick in 3 layer Plywood, grade BWR, type -BB, fixed with screws to timber frame work etc, as in use of false ceiling & incl beading size 40mm wide, for making to joint free false ceiling, complete all as specified and directed.

S&F GI Clip-in false ceiling tiles of with beveled edges of with G.I sheet (600mmx600mm) is manufactured out of 0.50mm galvanized steel of 100 gsm/sqmtr sheet having powder coated with 60 microns polyester paint on front side. These tiles shall have beveled edges. Two sides of each tiles are raised and piped and stopped to ensure positive engagement into the spring clip-in profile, yet allow for demounting of individual tiles. The rigid suspension system consists of rows of 0.5mm galvanized steel clip-in profiles of size 24mmx34mm of 0.5mm thick and installed at 600mm c/c spacing to support the tiles, clip-in profiles are suspended with hold on clamps. Suspension angles or 4mm G.I Wire are suspended from the roof structure. The tiles are held in place by pressure clips. In the flexible system the hanger and suspension clip replace the suspension angle. G.I Edge profile are of size 24mmx24mmx0.35mm thick with matching the color with tiles, complete all as specified and directed.

S&F 18/19mm thick Block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame, incl necessary beading wk where as required etc., complete all as specified and directed.

S&F 0.9mm thick decorative laminate(mica) type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed.

S&F continuous piano hinges mild steel bright finish or electro galvanized with open flap width 30mm, fixed with screw, complete all as specified and directed.

S&F in repair magnetic catches brass body for use in cup boards of kitchen, ward robes etc. fixed, complete all as specified and directed.

S&F in repair floor door stoppers 140mm of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floors, complete all as specified and directed.

Dismantling timber scantlings in any position in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section (Unframed work), complete all as specified and directed.

M&L for plain fillets, square, rectangular or triangular in section, and secured with nails or brads, using IInd class hard-wood clean sawn in sectional area exc 13 sqcm and not exc 25 sqcm complete all as specified and directed.

Dismantling timber scantlings, framed/unframed work of size 40 sqcm and over in section, in any position in any position with nails etc, complete all as specified and directed.

M&L 2nd class HW clean Sawn timber scantling/ posts complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate, laid in 1:20 slope as in plinth protection, coping, surface finished even and incl use and waste of necessary form work complete all as specified and directed.

S&F Mild steel butt hinges medium weight , clod rolled, 100mm, ISI marked, complete all as specified and directed.

S&F barrel tower bolts aluminium anodised extruded section of size 200mm complete all as specified and directed.

S&F 300 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts, fixed on plate or staple plate complete all as specified and directed.

S&F 250 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts, fixed on plate or staple plate complete all as specified and directed.

S&F aluminium fabricated type extruded handles of size 150 mm, complete all as specified and directed.

S&F aluminium fabricated type extruded handles of size 125 mm, complete all as specified and directed.

S&F in repair of 300mm mild steel ordinary rate tail rod pattern door spring incl roller and roller plate complete all as specified and directed.

S&F in repair 20mm dia stainless steel chromium plated curtain rails fixed with brackets, stops, rollers, etc. complete all as specified and directed.

Taking up or down 15 mm dia steel tubing incl connection and removal from site, complete all as specified and directed.

Taking up or down 20 mm dia steel tubing incl connection and removal from site, complete all as specified and directed.

S&F GI tubing medium grade with all fittings fixed to walls or laid in floors 15mm bore (concealed & open) complete all as specified and directed.

S&F GI tubing medium grade with all fittings fixed to walls or laid in floors 20mm bore (concealed & open) complete all as specified and directed.

S&F in repair 15mm bib tap cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair stop valve/ Angle cock/concealed fancy type cast copper alloy 15mm bore screwed down high pressure chromium plated concealed type complete all as specified and directed.

S&F in repair stop valve cast copper alloy 20mm bore screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union fixed complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

Dismantling water tanks exc 500 n. exc 1000 ltr capacity complete all as specified and directed.

S&F 1000 ltr capacity rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Part-I, complete all as specified and directed.

S&F 20mm bore dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipes etc, complete all as specified and directed.

S&F in repair vitreous china squatting span ORISSA Pattern size 580x440mm with integral foot rests, (excl flushing cistern and flush pipe) but with and incl connection to trap, and to flushing pipe anti-syphonage pipe, etc. complete incl provn of lime concrete and making good to floor, complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts,) complete incl making good to floor to match with adjoining surfaces, complete all as specified and directed.

S&F brass with CP finished, Jet spray with flexible pipe of suitable length fixed to 15mm bore pipe (faucet) complete all as specified and directed.

M&L for plastic water closet seat cover white closed pattern with flat bottom mild steel chromium plated or aluminium hinging device fixed in repair complete all as specified and directed.

S&F in repair 10 Ltrs capacity virgin polypropylene cistern, symphonic action type, ISI marked, white at low level complete with PVC bends, flush pipe and making all connections with and incl inlets ball valve float, handle, brackets and making good the disturbed surfaces in CM 1:3 to match with the existing surface, complete all as specified and directed.

M&L for PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in surface channel/ drains, incl fair finished & necessary formwork complete all as specified and directed.

M&L for mild Steel works as in bends straps, hold fasts etc, conforming to Fe-290, embedded portion duly painted with bituminous paint and sanded, complete all as specified and directed.

Dismantling of 100mm cast iron or reinforced concrete drain pipe, jointed in cement mortar and taking out of trenches/floor/wall if required complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified and directed.

S&F 110mm dia PVC (SWR) bends with oval access / plain door with rubber ring joints fixed as required complete all as specified and directed.

S&F 110mm dia PVC (SWR) junction double, (double T), equal or un equal with oval access door including jointing with solvent cement as required complete all as specified and directed.

M&L for preparation of new or previously untreated surface of wood or board materials of any description not otherwise described over 10cm in or girth & applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old wooden surface of any description not otherwise described over 10 cm width or girth & applying two coats of synthetic paint complete all as specified and directed.

M&L for preparation of new steel surfaces including preparation of surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces including preparation of surfaces and applying one coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls and applying one coat of exterior emulsion/ Apex paint complete all as specified and directed.

Complete removal of existing old surfaces applying two coats of oil bound distemper over one coat of wall care putty (2mm) on walls complete all as specified and directed.

M&L for preparation of newly plastered or unplastered or previously untreated surfaces of walls and applying two coats of exterior emulsion/ Apex paint complete all as specified and directed.

M&L for two coats of distemper oil emulsion on wall incl preparation of new surfaces over one coat of primer on wall surface incl 1mm thick wall care putty, complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc Laid, bedded and pointed in any mortar, complete all as specified and directed.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid & dado and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete over and including 15 mm thick screed bed or bedding with CM 1:6 ,etc complete all as specified and directed. Note:- (i) The quoted rate of kota stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular. (ii) The quoted rate shall also be deemed to incl for cutting and polishing machine and kota polishing to achieve the desired granite finish.

M&L for Green/ Black marble flooring/ woor/ windows cills, or on cooking platform 18 to 20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick cement screed bed in CM(1:6) complete all as specified and directed. (size of the slabs shall not be less than 100cmx60cm ) Note:- (i) The quoted rate of granite stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular. (ii) The quoted rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achieve the desired granite finish.

Supply only water proofing compound all as specified as per manufacturer instruction, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

S&F roof trusses (framed) trussed, purlins, posts, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats conforming to Fe 410-W (Gde-E- 250) quality-A etc complete all as specified and directed.

S&F framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladder, framed baluster, walk ways, railing, framework of water tanks staging and similar work conforming to Fe-290. Gde-E-165, complete all as specified and directed.

S&F Mild steel plain black sheet 0.80 mm thick in hearths, covering to door shutter, valley gutter, ducts use as in ceiling, etc, cut to size, edges beaded if directed, holes punched, including round headed screws, clout nails or rivets, fixed to wood or steel members with plain 40mm lap joints or welded/ riveted seams including bending, turning up, mitered angles, stopped ends, etc. as required complete all as specified and directed.

M&L for coloured chequred cement conc tiles 30cm x 30cm x 22 to 25mm thick in grey cement and with pigment in floors etc, set and jointed in neat cement slurry, over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S&F in repair for 50mm thick PCC 1:4:8, type D-2, using 40mm graded aggregate, as in filling of mass concrete for sub base floors complete all as specified and directed.

M&L for PCC 1:4:8, type D-2, using 40mm graded crushed stone aggregate, as in filling of mass concrete for floors complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as base coarse for floors, complete all as specified and directed.

M&L for preparation of new external surfaces of wall & applying two coats of cement based paint over chalk whiting complete all as specified and directed.

S&F 2nd class hard wood 30mm thick made glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass, etc, size of members of window shutters as specified in SSR Part-1, complete all as specified and directed. .

M&L for solid PVC as in use wall/ceiling lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing incl necessary beading work, incl same board beading for joint sealed, complete all as specified and directed.

S&F 9mm thick in 5 layer Plywood, grade BWR, type BB, fixed with screws to timber frame work etc., complete all as specified and directed.

S&F galvanized mild steel wire cloth 0.56mm fixed nominal water proofing of wire and avrg width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple, complete all as specified and directed.

S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty or secured with wooden beads as required in square n exc 0.5 sqm in each pane, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate, laid in 1:20 slope as in plinth protection, coping, surface finished even and smooth without using extra cement, with and incl use and waste of necessary form work complete all as specified and directed.

S&F 150mm long mild steel barrel tower bolts, stove enameled black, with bright bolt and fixed complete all as specified and directed.

S&F 300mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F 125mm mild steel pressed handles, oval type, stove enameled black complete all as specified and directed.

S&F CGI sheeting 0.63mm thick with grade of zinc coating 275 as in roof covering fixed with L or J type hooks or self thread making steel screws of length not less than 75mm with suitable arrangement as required, complete all as specified and directed.

Roughening surface of old concrete by picking, sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg of cement per sqm, complete all as specified and directed.

S&F in repair 75mm thick, PCC 1:4:8, type D-2, using 40mm graded crushed stone aggregate, as in filling of mass concrete for sub base floors, complete all as specified and directed.

M&L for cement concrete/ colour chequered tiles 25cm x 25cm x 22mm thick, machine pressed, set jointed and pointed in neat cement slurry in floors, and cut and polished, over screed bed as in CM 1:4,15mm thick, complete all as specified and directed.

M&L for joint free Non Skid glazed ceramic tiles (coloured) 400x400x 7 to 8mm thick (square/rectangular) as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:6) complete all as specified and directed.

M&L for glazed ceramic tiles joint free in vertical surfaces of size 350x250x7mm/ 450x300-350x7mm/ 300x200x6to7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick backing coat in CM 1:4, complete all as specified and directed.

S&F 5mm thick looking mirror with 6mm thick back ply wood and wooden frame complete including plugging on wall and fixed, complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, bracket guard and railing 60cm long incl screws, complete all as specified and directed.

Removing demolished/ excavated material /soil .n exc 50m depositing were directed at a level n.exc 1.5m above the starting point, complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tanks 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part 1 etc complete including 20mm dia float valve and dismantling of existing tank, complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to draft wall including brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F stainless steel plate rack of size 900mm x 750mm with shelves, hooks and railing to keep plates vertically and horizontally, including necessary fixing arrangement, complete all as specified and directed.

M&L for 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement, complete all as specified and directed.

S&F in repair 15mm bore CP fancy type (sink mixer for mixing hot & cold water cast copper alloy with capstan handle, screwed down for iron pipe and fixed on wall, WHB complete all as specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan socket or power) complete incl (fitting such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc.), removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc., complete all as specified and directed.

M&L for point wiring 1.5 Sqmm (nominal cross sectional area) with colour coding multistranded copper conductor cable, PVC insulated (FRLS-H) and unsheathed cable and including drawn through PVC casing-N-capping of 25X32mm size with all fittings and accessories, terminated to PVC board of suitable size for housing /mounting the switches/sockets including 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable earth wire connected to common earth dolly for one light point control by one, one way switch complete all as specified and directed.

All as per Srl item No 123.00 above but one 3 pin socket outlet 5 amps, on independent board, complete all as specified and directed.

All as per Srl item No 123.00 above but one 3 pin socket outlet 5 amps, on same board with other switches, complete all as specified and directed.

All as per Srl item No 123.00 above but for one 3 pin 15 Amps power point on independent board with 2.5 Sqmm size FRLS-H PVC insulated unsheathed multistranded copper conductor cable and with 2.5 Sqmm FRLS-H PVC insulated unsheathed multistranded copper conductor as earth wire, complete all as specified and directed

S&F switch piano flush single pole, one way 5 Amp, complete all as specified and directed.

S&F switch piano flush single pole, one way 15 Amp, complete all as specified and directed.

S&F socket, 2 in 1, 3 pin 5/6 amps flush type, complete all as specified and directed.

S&F socket 2 in 1, 5 pin 5 and 15 amps, flush type universal, complete all as specified and directed.

S&F ceiling rose, 3 phase, PVC polycarbonate, insulated body, complete all as specified and directed.

S&F LED inverter batten tube light along with fixture, 1x 20 watt, (4 Feet) wall mounted LED batten, with diffuser, complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed.

M&L for lamp holder (Angle) PVC/ Polycarbonate type with back plate suitable for batten fittings LED 15 Watt CFL, complete all as specified and directed.

S&F inventor building security light 25 watt fixed on wall suitable bracket with all connected accessories complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed.

S&F LED tube light along with fixture, 1x 10 watt, (2 Feet) wall mounted LED batten, extruded PVC, heat sink provided for efficient heat dissipation & integrated electronic driver, optics diffused, complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed.

S&F inventor light fitting 9/10W bulkhead luminaire including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including taking down old unsv existing fittings complete all as specified and directed.

S&F in replacement of Bed side lamp decorative, E-27 screw type holder with 0-2 watt bulb suitable for bedroom, study room, complete all as specified and directed.

S&F 10 Sqmm flat twin core, 1100 Volts grade, stranded, heavy duty, cable PVC insulated aluminium conductor, weather proof and including taking out the unserviceable cable, etc., complete all as specified and directed.

M&L for sub main wiring with 2X6.0 Sqmm+1x6.0Sqmm earth wire single core PVC insulated FRLS-H PVC sheathed cooper cable connecting to common earth dolly in and including heavy duty PVC Casing-N-Capping as per site requirement and direction by EIC, with all accessories complete all as specified and directed. Note: Three runs of copper wire for phase , neutral, earth & one run PVC conduit/ casing shall be measured one unit length.

S & F sheet metal enclosure MCB DB 8 way SPN double door suitable for 240 V, 200 amps rated bus bar/ DIN rail, fixed and flushed on walls including cutting Knitch and making good disturbed surfaces complete all as specified and directed. Make : L&T / Legrand / Schneider.

S&F MCB, SP (single pole) 05 to 32 Amps, 10 kA, B curve for inductive load connected through cable lugs of suitable size complete all as specified and directed. Make : L&T / Legrand / Schneider.

S&F MCB, SPN (single pole and neutral ) 40 Amps for inductive load connected through cable lugs of suitable size complete all as specified and directed. Make : L&T / Legrand / Schneider.

S&F electric water heater, in replacement storage type steel body with copper inner tank and heating element up to 2 KW capacity 25 Litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc and fixing arrangements, complete all as specified and directed.

S&F 15/20 Amp, socket with 16/20 Amp, MCB with metal box combinations flush type universal, complete all as specified and directed.

Supply and laying Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground, complete all as specified and directed.

S&F Air termination, single pointed aluminium rod 12mm dia and 300mm long, complete all as specified and directed.

S&F test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos, 8mm dia 25mm long hex. head screw, complete all as specified and directed.

M& L for Earthing complete with galvanized steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less 'than 1.5 meters below normal ground level, connected to galvanized earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion including galvanised strip protected by 32 mm bore light grade galvanized iron pipe and earth and connected to test point as directed including funnel, watering pipe 20 mm bore light grade galvanized iron wire mesh charcoal and common salt in alternate layers of 15 cm compacted thickness all around the GI electrode with concrete pit in PCC 1:3:6 type C1 including necessary excavation in soft/loose soil and disposal of soil to a distance not exc 50 m and necessary testing complete connected to earthing test point, complete all as specified and directed.

All as per Srl item No. 148.00 above but using galvanized iron strip 32x6mm as earthing lead

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanized iron or steel wire

All as per Srl Item No 150.00 above but for 32x6mm galvanized iron strip complete all as specified and directed.

S&F 16 Sqmm flat twin core, 1100 Volts grade, stranded, heavy duty, cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than one meter apart including 4 mm suspension wire from LT pole to service bracket and including taking out the unserviceable cable, etc., complete all as specified and directed.

Supply, fixing or laying HDPE (DWC) tubing 40mm dia as per IS:16205 part 24 fixing on poles, walls under floors, laying on surface etc as reqd at site complete all as specified and directed. Note: All items and accessories, bend, joints, nut bolts, clamps for wall fixing as per site requirement etc are incl in quoted rates.

M/S Meera Builders (BID ID -3263103)

shiv const co (BID ID -3265960)

M/S kuldeep kumar khullar (BID ID -3269421)

M/S J.S.ENTERPRISES (BID ID -3263244)