MP FUND - CONSTRUCTION OF PDS SHOP

Amount

Earth work excavation for foundation in all clauses of soils and sub soils to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and boiling out water whenever necessary etc complete complying with standard specification

Supplying and filling in foundation and basement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain cement concrete 1:4:8 mix ( one cement five sand and ten aggregate)using 40mm gauge hand broken granite stone jelly for foundation including dewatering if found ecessary and laid in layers of not more than 15 cm thick and compacted,etc., complete complying with standard specfication

Fly ash Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand)) using Fly ash bricks of size 9" X 4 3/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Supplying, fabricating and placing in position of Steel Reinforcement using Mild steel or Ribbed tor steel rods, for all RCC works as per the design given by the departmental officers including cost of steel and binding wire and all labour charges for cutting, bending, tying and placing in position etc, complete as per SS.

Providing centering for sides and soffits of R.C.C.works such as lintels, slab that beams plain surface etc., complete including shuttering upto 3.30 M height using mild steel sheet of size 90 c.m x 60 c.m and 10 gauge stifer with M.S. angles of size 25 mm x 25 mm x 3mm laid over silver w.c.wood joints of size 10 c.m. x 6 c.m. spaced at about 90 c.m. c/c and supported by casurins props of 10 c.m. to 13 c.m. dia spaced 75 c.m. centre to centre complying with as per standard specification.

Plinth beam

Column

Reinforced cement concrete 1: 1 1/2:3mix(One cement, one and a half sand and three aggregate)mix for all reinfoced cement concrete works using 20 mm ISS gauge hard broken grainte machine crushed metal including cost and conveyance of all materials at site including all labour charges for concrete mixing, laying, watering, curing properly but excluding cost of steel and centering etc., complete complying with standard specifications.

Below GL

Above GL

Special ceiling plastering in cement mortar 1:3 mix 10mm thick using clean screened sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting for plastering for plastering and protecting from other damages till setting of mortar etc.complete complying with standard specification.

Plastering in cement mortar 1:5 mix 12mm thick using clean screened sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting for plastering for plastering and protecting from other damages till setting of mortar etc.complete complying with standard specification.

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54. Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers.etc., complete.

Finishing the top of the roof slab with one course of Machine pressed tiles of size 23cm x 23cm x 2 cm of approved quality laid in cementmortar 1:3 ( one cement and three sand) 12mm thick mixed with waterproofing compound 2 % by the weight of cement used and the top pointed with red oxide etc., complete complying with standard specification.

Floor finishing with Grano lythic flooring 25 mm thick in cement concrete 1 : 2 : 4 ( 1cement ,2sand , 4 aggregates) mix using 10 to 12 mm size metal, and top rubbed smooth, including cost of all materials and labour charges for mixing, laying , finishing, watering etc., complete as per standard specification.

White washing two coats using best quality slacked shell lime including cleaning surface watering curing including cost and conveyance of all materials at site and all labour charges etc., complete complying with standard specifications.

Manufacturing, Supplying and fixing inposition of Mild Steel Door using outer frames of size 40x40 x6mm and shutters with 18G CRC sheet in center portion and finishing with necessary locking arrangements, painting with primary coat as directed by departmental officer etc. complete.

Supplying and erecting pull and push type rolling shutter with ISI make of approved size and section using 18 GI sheet. The shutterr shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers,transportion charges etc., Rolling shutters with ISI monogram manually operated.

Manufacturing, supplying and fixing in position of MILD STEEL WINDOWS with openable shutters, outer frames and shutter frames shall be made out of steel sections conforming to I.S. 7452/1990. The outer frames and shutter frames of windows made out of ' Z ' section ( F.7D ) of size 25 X 20 X 3mm and confriming to I.S.7452/1990. Mullions are made out of ( F.4B ) ' J ' sections of size 46 X 25 X 3mm and confriming to I.S. 7452/1990. The shutter shall be individual and each of them can be operated seperately. Sash bars shall be made of " T " ( T 2 ) of size 25 X 25 X 3mm. Four numbers of 40 X 40 X 3mm angel hold fasts of 230mm length should be welded to the outer frame of sturdy hinges and one number of handel-cum-latch of special type shall be left for its easy operation. One number of adjustable wind stay with locking bracket of sufficient length shall be provided for each shutter. Mild steel square guard bars of 12mm size shall be welded to the inner face of the window at equal intervals not exceeding 100mm spacing and 18G CRC sheet for shutter panes and welded with shutter frame.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Painting two coats for new Iron work using the best quality Iron best quality synthetic enamel paint etc complete complying with standard specification.

PAINTING TWO COATS with best colour and approved quality of EXTEIOR EMULSION PAINT over a priming coat including thorough scrapping the plaster surface clean removal of dirt etc., complete cost including cost and conveyance of all materials such as,brushes,scaffolding charges etc., complete complying as per standard spefication.

Paving the floor with vetrified tiles (desin should be got approved by the departmental officers before purchase (colour and shade as directed) of size 600 mm x 600mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc completecomplying with standard specification

Casting and Fixing RCC Pre Cast slab-75 mm tk in CC 1:2:4 using 20 mm HBGS excluding cost of Reinforcement grill inposition including moulding curing and finishing etc; complete complying with standard specifications.