Development of Sindhfana River Ghat under Rajmata Jijau Nadi Ghat Pariyojana belongs to Nagar Parishad (Construction of C.C. Road from Old Bridge to Siddheshwar Temple) in Majalgaon Tq. Majalgaon District Beed in the state of Maharashtra

Amount

Excavation for foundation in earth, soils of all types, sand, gravel, soft murum including shoring and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete. (By Mechanical Means) a) Upto 1.50 metre lift Normal Rate

Supplying hard murum/ kankar at the road site, including conveying and stacking complete.

Spreading hard murum/ soft murum/ gravel or kankar for side width complete

Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etcetera complete.

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader / Paver on prepared surface, mixing by mix in place method with rotavator at Optimum Moisture Content, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- By Mix in Place Method and Grading - II Material

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density. By Mechanical Means -Grading I (Using Screening Type B (11.2 mm) Aggregate)

Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate (Natural Sand/ VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 mili metre,, cement content not to be less than 150 Kilogram/ Cubic Metre, Optimum Moisture Content (OMC)to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge, compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etcetera complete.

Providing and laying in-situ M-30 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate(VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/ non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver, compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @0.6 metre X 0.6 metre centre to centre, admeasuring 80 mili metre at bottom and 40 mili metre at top with depth of 75 mili metre and maintaining the same throughout curing period by any other method approved by Engineer-in-charge.

Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet Confirming to Indian Standard 3395 : 1997 below concrete pavement including all materials and labour complete.

Providing and fixing in position Thermo Mechanical Treated (TMT) FE 500, tie bars precoated with anticorrosive epoxy paint of 12 mili metre diametre 70 centi metre long and at 30.00 centi metre centre to centre and wherever directed including handling, straightening wrapping with paper of approved quality for half length, necessary cutting, handling, straightening, supported by assembly of Thermo Mechanical Treated (TMT) FE 500, chairs with proper alignment etcetera complete.

Providing and fixing in position Thermo Mechanical Treated (TMT) FE 500, 32 mili metre diametre dowel bars precoated with anticorrosive epoxy paint of required diametre 60 centi metre Long and at 30.00 centi metre centre to centre and wherever directed including handling, straightening, necessary cutting supported by Thermo Mechanical Treated (TMT) FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed etcetera complete.

Cutting transverse contraction joints 3 to 4 mili metre wide and depth 60 mili metre .in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay / slab etcetera complete including subsequent widening of the groove 8 to 10 mili metre wide at top having depth of 15 mili metre as directed by Engineer incharge.

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned up to a lead of 1000 Metre including removal and disposal of top organic soil not exceeding 150 mili metre in thickness.

Providing to contraction joints polysuphide sealant (Pouring grade) confirming to BS : 5212 - 1989 into sawed groove widened at top for sealant reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter (appraox. 25% larger than the initial 3 mili meter 4 mili metre joint) overlaid with bond breaking tape as per detailed drawing. Item includes cleaning the joints with water jet / air compressor and allowing joint to become thoroughly dry before sealant is applied and applying primer. (A) Contraction and longitudinal joints (15 mili metre deep x 8 mili metre wide)

Transportation of excavated material with lead & lifts away from site 3.00 km. etcetera complete as directed by Engineer in Charge.

Providing soling using 80 mili metre size trap metal in 15 centi metre layer including filling voids with Crushed sand/grit, ramming, watering etcetera complete.

Providing and laying in situ / ready mix cement concrete of M-10 proportion with trap/ granite/ quartzite/ gneiss metal in foundation including necessary form work, compacting and curing etcetera complete. (with reversible drum type mixer with SCADA with fine aggregates of required specifications (Natural sand / VSI sand finely washed etcetera )

Providing cast in situ / ready mix M-20 grade cement concrete for head walls of Cross Drainage Work / retaining walls etcetera including necessary form work, compaction, finishing and curing etcetera complete. (with reversible drum type mixer/ concrete batch mix plant (pan mixer) with SCADA

Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 450 mili metre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etcetera complete.

Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 900 mili metre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etcetera complete.

Providing and laying in situ / ready mix M-30 plain cement concrete of trap /granite/quartzite/ gneiss metal for cast in citu piers, abutment, returns, wings etcetera including provision of "V" shaped false joints to form suitable panels on the faces to approve design with compacting by vibrating and curing complete, including plywood/steel form work centering ( excluding dewatering by means of pump) and including bailling out water and curing finishing in cement mortor 1:3 etcetera complete. as directed by engineer in charge basic rate shall be increased for height above 5.00 metre in followinh manners (a) Height upto 5 metre (With Concrete Mixer)With fine agreegates of required specifications (VSI sand finely washed etcetera ) i) Height up to 5 metre, normal rate. ii) Height 5 to 7.50 metre, add 5 percent extra over basic rate. iii) Height 7.50 to 10 metre, 7.50 percent extra. iv) Over 10 metre Height, add 10 percent extra for every 2.50 metre rise.

Providing and laying weep holes of 100 mili metre diametre Poly Venyle Chloride pipes as per drawing for abutment returns, return walls etcetera Complete.

Back filling behind abutment, wing wall and return wall as per drawings and technical specifications etcetera complete. (by granular material)

Conveying materials obtained from road cutting including all lifts, laying in layers of 20 centi metre to 30 centi metre breaking clods, dressing to the required lines, curves, grades and section, watering and compacting to not less than 97% of standard Proctor density for a lead of over 50 metre to 300 metre inclusive from the site of excavation to the site of deposition as directed.

Providing, cutting, bending, hooking, tying and laying in position Thermo Mechanical Treated (TMT) FE 500 steel bars for reinforcement for all Reinforced Cement Concrete works as per detailed drawings etcetera complete.

Yash Construction co

M/S B. R. ANDE CONSTRUCTION COMPANY

C B Bikkad Engineers and Contractors