CWE/P-41/2019-20SPECIAL REPAIR TO ORS MD ACCN BLDGS NO NP-29/01 TO 08 AT MIRTHAL UNDER GE SOUTH PATHANKOT

Amount

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each including taking out hold fast complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each including taking out hold fast complete all as specified and directed.

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 105 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after tarring of hollow portion of frame complete all as specified and directed

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 125 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after taaring of hollow portion of frame complete all as specified and directed.

M&L Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (two panel) with lock rail and panel of 9mm BWP commercial plywood or 12 mm veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated all as specified.

M&L factory made Glazed and skelton shutters 30mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (without shash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in SSR Part-1, secton 8, clause 8.24(a) kiln seasoned and pressure treated all as specified.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixed complete alll as specified .

M&LFactory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with Particle Board Core 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing as per SSR Part II 2010 complete alll as specified . .

Supply and fxing in repairs, 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate fixed in repair complete all as specified.

S & F mild steel sliding door bolts, stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolts plate and two on staple plate, 300mm long, all as specified.

M & L Mild steel butt hinges, medium weight, cold rolled (ISI marked),100mm long , complete all as specified.

Supply and fxing Aluminium anodised, barrel tower bolts of extruded section of size 150mm ISI marked and fixed, complete all as specified and directed.

M & L Aluminium alloy handles (ISI marked), cast type, anodised of size 150mm and fixed, complete all as specified and directed.

M&L Steel window/ Ventilator factory made out of M S tubular frame with double shutter with sash bar made out of section using flash butt welding, hinges (ISI marked) shall be provided to both shutters with fittings and grills complete and one shop coat of red oxide primer all as per drg No CEPZ/TD/245/01 Sh 1/1, CEPZ-TD/246/01 Sheet 1/2 and Sheet 2/2 all as specified and directed by Engr-in-Charge. Note: (i) Cutting holes for hold fast making good in cement mortar 1:3 and PCC 1:2:4, type B-1 shall be included in the quoted rates. (ii) Grills/Gaurd bar shall be measured and paid separetely

M & L framed work such as grills, grating etc with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barrel, iron doors, ladders, balusters, walkway, frame work of water tanks and similar work confirming to Fe-290 Gde E-165 complete all as specified.

M & L 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified.

M & L galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified.

Preparation new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified.

Preparation new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

M&L brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar 1:4, complete all as specified and directed.

Taking down cement plaster or cement line plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

M&L 15mm thick rendering in cement mortar 1:4 on fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified

M & L 10mm thick cement plaster rendering in cement mortar 1:6 on fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified

M & L 5mm thick cement plaster rendering in cement mortar 1:3 in facia or edging of Chajjas, ceiling and roof projection and making the line in true shape & finishing the surface even and smooth without using extra cement, complete all as specified.

M& L for preparation of new plastered surfaces of walls and applying two coats cement base paint of approved brand all as specified.

M & L for preparation of new plaster surface of walls including cornices pilaster etc, and applying two coats of oil bound distemper, complete as specified and directed.

M&L for three coats of white wash including preparation of newly plastered surfaces of ceiling complete all as specified.

M&L for preparation of old plastered surfaces and applying two coats of white wash on wall all as specified.

M& L for preparation of old treated surfaces of walls and applying two coats cement base paint of approved brand all as specified.

M & L for preparation of old treated surface of walls including cornices pilaster etc, and applying two coats of oil bound distemper, complete as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically described complete all as directed by Engineer-in-Charge.

M & L Plain Cement Concrete 1:3:6, type C-1 (using 20mm crushed stone aggregate), 75mm thick as in plinth protection, flooring etc laid in alternate bays finishing even and smooth without using extra cement complete all as specified.

M & L machine pressed chequered cement concrete tiles 300x300x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment including 20mm thick in cement moratr 1:6 complete all as specified and directed.

M & L Plain Cement Concrete 1:3:6, type C-1 (using 20mm crushed stone aggregate), 75mm thick as in sub base cement complete all as specified.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

M&L Steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

All as per Srl item No 37 here-in-before but except pipe.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

M&L Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

All as per Srl item No 40 here-in-before but except pipe.

Dismantling water tanks and removing from site capacity exceeding 250 ltr and not exceeding 500 ltr complete all as specified and directed.

Supply and fxing rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug complete all as specified and directed.

S &F 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms)

Supply and fixing 20 mm stop valve of cast copper alloy , butterfly handle (ISI marked), screwed down high pressure, screwed both ends for iron pipe or for unions , complete all as specified.

Supply and fxing in repairs,Vitreous china Wash hand basin, white, flat back/angle back type of size 550x400mm including brackets, brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc , complete all as specified.

Supply and fxing in repairs, Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, white, with integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe of 32mm dia and syphonage pipe etc, and including concrete bedding complete, all as specified and as directed.

Supply and fixing in repairs kitchen stainless steel sink with drainage board 1mm thick with plugs, washers and wastes including fixing bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410mmx330mmx160mm fixed, complete all as specified.

Supply and fxing in repairs, PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all joints , complete all as specified.

Supply and fixing in repairs Bib taps 15mm bore of cast copper alloy chromium plated (ISI marked) fancy type, screwed down, high presure, screwed both ends for iron pipe or for brass ferrule, complete all as specified and directed.

Supply and fixing in repair 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated (ISI marked), screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed shank and fly nuts screwed for iron pipe complete, all as specified & directed

Supply and fixing in repairs angle valve of cast copper alloy chromium plated (ISI marked), fancy type screwed down high pressure, screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified.

Supply and fixing concealed stop cock, fancy type , chromium plated (ISI marked) with long shank and cup , screwed down, high pressure, with capstan head, screwed both ends for iron pipe of 15mm bore, complete all as specified and directed.

S&F swivel shower rose of PTMT any colour incl fixing to steel pipe or union fixed (Minimum weigtht 40 gms) complete all as specified and directed.

M&L PVC connection 15mm size with PTMT nuts on both ends of length 450mm , complete all as specified.

S & F in repairs tubular towel rail 60cm long between flanges , 20mm dia D type Brass Chromium plated incl necessary brackets, fixed with chromium plated screws and wooden/plastic cleats complete all as specified and directed.

S&F in repairs grating square fitting of PTMT of size 100 mm (Minimum weigtht 25 gms) complete all as specified and directed.

Supply and fxing in repairs, cast iron floor trap of 100mm dia of outlet, including jointing to waste pipe with fixed in cement concrete 1:2:4, type B-1 complete all as specified.

Dismantling/ taking down of cast iron or unrienforced concrete or PVC soil waste and drain pipe 75mm or 100 mm dia with all fittings complete all as specified and directed

Supply and fxing 100 mm dia sand cast pipe, cast iron soil waste and vent pipe ISI marked in any length with or without ears with cement joints fixed to wall, complete all as directed

Supply and fxing 75 mm dia sand cast pipe, cast iron soil waste and vent pipe ISI marked in any length with or without ears with cement joints fixed to wall, complete all as directed

S & F 100 mm dia cast iron cowl ISI marked complete all as specified and directed.

S & F 75 mm dia cast iron cowl ISI marked complete all as specified and directed.

M&L PVC (SWR) pipes 110mm dia ISI marked any length single socketed with rubber ring joint fixed to walls as drainage pipe complete all as specified and directed.

M&L PVC (SWR) bends any radius of 110mm dia ISI marked complete all as specified and directed.

Supply and fix in repairs 18/19 mm thick block board, grade 2 quality, interoir grade , commercial type, fixed with screws to timber frame work complete all as specified and directed.

M&L 2nd class hard wood (Hollock), plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified.

Supply and fxing Hasp and staple,100 mm long stove enamelled , including bolt to hinge plate and fixed with screws complete all as specified. ISI Marked

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Non-skid cermic coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 15 mm thick in cement mortar 1:6 complete all as specified.

M&L Non-skid cermic coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 15 mm thick in cement mortar 1:6 complete all as specified.

M&L Glazed ceramic coloured tiles in skirting/dado 350 x 450 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over and including 10 mm thick cement plaster in cement mortar 1:4 as in backing coat rough finished surface complete all as specified.

M&L machine cut kota stone slab flooring 20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, size of each slab not be less than 0.28 Sqm, including rubbing and mirror polishing complete over 20mm thick screed bed in cement mortar 1:6, complete all as specified.

M&L Kota stone slab 20mm thick in riser of steps, skirting, dado and pillar laid over cement screed in cement mortar 1:4, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing & complete all as specified & directed.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in cooking platform and like in cement mortar 1:4 over 20mm thick screed bed or bedding layer in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admisture of pigment to match with shade of granite complete all as specified & directed.

Supply and fxing in repair curtain rod 25 mm dia pre painted synthetic enamel paint of wooden finish , fixed with screws complete all as specified.

Supply and fxing in repair wooden (turned, weathered & mitred) brackets (set of two) of Ist class hard wood pre polished with french polish and touch wood with cut hole suitable for 25 mm dia rod fixed with screws and gutties in wall, complete all as specified and directed.

Supply and fxing in repair wooden (turned, weathered & mitred) end caps (set of two) with ornament and fixed to curtain rod of 25 mm dia with screw of design/shape complete all as specified and directed.

S&F Doctor fixit Pidfin 2K high performance 2 component flexible Acrylic polymer modify cement base water proofing coating in two coat 1mm thick dry film mixed in ratio 2:1 by weight or 1.5:1 by volume product of M/S Pidilite Industry Limited Makers of Fevicol adhesive brand complete all as specified

M & L PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in padding in roof slabs/chhajjas/ sunken including water proofing compound @ 3 % by weight of cement and finishing the surfaces even & smooth without using extra cement, complete all as specified and directed.

Taking out and cleaning of existing roof treatment of any descrition completely and washing, rubbing with water and providing 20mm thick in cement mortar (1:3) on flat roof surfaces mixed with liquid water proofing compound @ 4% by weight of cement, finished fair and even without using extra cement, to receive water proofing treatment complete all as specified. (The rate includes for filling cracks in existing roof with cement putty using suitable bonding agent (shalcrate 42) before laying cement plaster)

M & L for providing and laying of water proofing treatment of roof APP (Atactic Polyproplyllen) modified prefabricated five layer 3mm thick water proofing membrane, super thermply non woven polyester mat reinforcement of 160 gsm, weight of membrane @ 3.6 Kg/Sqm over a solvent based bitumen primer @ 0.3 Ltr Sqm by the same manufacturer conforming to IS:3384-1986 , The membrane shall be laid using bitmun torch.The end lap should be 100 mm and the side lap must be minimum 75 mm the membrane shall be first laid up to the parapet wall junction and then shall be overlapped with another membrane (flashing) with an overlap covering up to a distance of 300mm. In case parapet height is less than/ up to 500 mm, membrane shall be terminated at the top of parapet.All rain water pipe opening shall be suitably sealed with the APP membrane all as specified and directed.

M & L 40 mm thick brick tiles laid on 15 mm thick cement mortar 1:6 and joints grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cement, complete all as specified and directed

Taking down old damaged SGSW pipes from exiting lines inlcuding necessary excavation of old fitted in trenches and supply and fixing UPVC under ground drawongs pipe (UDS) type 'B', 150mm dia with wall thickness 4mm (minmum) and pressured 4 KN/Sqm jointed in cement solvent complete including providing cement concrete (1:4:8) type 'D-2' using 40mm graded crushed stone agrregate as in bed including packing under and huanching against the sides of the pipe after they are laid, tested and including removing and returning filling of soils all as directed by Engr-in-Charge.

Supply and fxing in repair stainless steel plate rack 700 x 750 x 300 mm deep with plate rack, spoon holders , shelves etc , complete all as specified.

M & L pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Precast RCC 1:2:4, type B1 (using 20mm graded aggregate) as in cover slabs for Man holes etc set in CM 1:6 complete all as specified and as directed

TMT bars 6mm to 8mm dia. as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

M&L Point wiring for light/fan/bell point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc ) made of not less than 16 gauge MS sheet and 6cm depth covered with 3mm thick laminated bakelite sheet fitted with brass screw and washers and including 1.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) (b) On RCC roof ceiling PVC conduit shall be provided on surface for fan with proper fixing clips all as directed.

All as per above item no 91.00 here in before but for one 3 pin socket outlet 5 amp on same board all as specified and directed.

All as per above item no 91.00 here in before but for one 3 pin socket outlet 5 amp on independent board all as specified and directed.

All as per above item no 91.00 here in before but for one light controlled by two way switch all as specified and directed.

M&L Point wiring for 15 Amp socket point controlled by one switch with 4 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc ) made of not less than 16 gauge MS sheet and 6cm depth covered with 3mm thick laminated bakelite sheet fitted with brass screw and washers and including 4sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green)

M&L Switch piano flush type 5 Amp single pole one way, (ISI marked), complete all as specified.

M&L Switch socket combination 2 in 1, 3 pin, 5 & 15 Amp flush type,complete all as specifed.

M&L Switch piano flush type 5 Amp single pole two way, (ISI marked), complete all as specified.

M&L switch socket combination 2 in 1 , 3 pin 5 Amp flush type all as specified & directed.

M&L socket outlet 2 in 1, 3 pin, 5 Amp flush type ,complete all as specifed.

M&L bell push 5 amp, 240 volt, flush type (ISI marked) , complete all as specifed.

M&L buzzer ding dong AC 230 volts all as specified and directed by Engineer-in-Charge.

M&L Stepped type electronic fan regulator 0 to 4/5 step , flush type, heavy duty with hum free snubber circuit complete all as specified.

M&L Ceiling rose, 3 phase/bakelite 65x50mm two or three therminals isolated body fixed on PVC round block complete all as specified.

S&F in replacement sheet metal enclosure factory made (Double door) type IP-43 Protection. Isolated Neutral,Door earthing, cement spill protector, IK-08 complete, single pole and neutral, 240 volts, 50 Hz, 8 way with 200Amps rated copper bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

S & F in replacement existing unsv distribution board iron clad, with double door 4 way with IP-54,1K-09 protection,cemet spill prptector suitable for MCCB as incommer AC 415 Volts three pole with thermal release adjustable type (80% to 100 % ) and MCB as outgoing ,complete with appropriate size copper bus bar and neutral link complete with including one MCCB 3 pole 415 Volts 125 Amps rating with rupturing cap 25 KA of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge (Outgoing MCB will be measured separately).

M&L MCB SP 6 to 32 Amp, 240V with 10KA breaking capacity of 'C' series 10 KA all as specified and directed.

S&F MCB single pole & neutral 6 to 32 Amps, 240 Volts 'C' series, 10 KA, complete all as specified.

Supply and Fix in replacement existing UNSV tube light fitting with LED 20W inverter batten type fitting 4 feet long aluminium extruded housing, charging time 10-12 hours and back up time 04 hours, IP-20 ,rated voltage 230 V, 50 hz, system wattage 20W +/- 10%, system current less than 102 mA, power factor more than 0.95, system lumen efficiency 100lm/watt,CCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85% complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed. Notes: (i) LM79 report from third party (instead of company in house lab) NABL/UL accredited lab (ii) LM 80 report from LED manufacturer (iii) Test certificates to be submitted before commencement of work/ claiming for payment . (iv) Warranty certificate for minimum 2 years to be submitted from OEM.

Supply and fixing in replacement existing unsv integrated LED bulk head light fitting 1X10 watts IP-65 protection connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm all as required.

S&F in replacement existing UNSV sleek LED mirror light fitting 2 feet long 1x10 W including LED tube 2 feet long having ballast, bipin holder, connector block etc complete all accessories prewired and connecting electrically to ceiling rose usning PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as directed by Engr-in-chagre Notes for Srl item no 107 & 108 :- (i) Driver efficiency more than 85% ( Constant current driver) (ii) Non isolated type driver (iii) THD less than 20% (iv) LED driver current less than 60 mA (v) Efficiency of LED Chip more than 130 lm/watt (vi) Efficiency of LED Fixture 100 lm/watt (vii) Surge protection 2.5 KV & above as per IEC standard (viii) working humidity 95%RH (ix) LED Make Nichia /Philips lumiled/ Cree/Osram/Seoul/Bridgelux/Nationsear (x) Life 50000 Hrs at 70% lumes (xi) CRI more than 80 (xii) Working temp -10 degree to 50 degree C (xiii) Heat Sink extruded aluminum (xiv) junction temperature 85 degree C (xv) Body of fitting Extruded Aluminum (xvi) impact code Min IK 03 or more

(xvii) LM79 report from third party (instead of company in house lab) NABL/UL accredited lab (xviii) LM 80 report from LED manufacturer (xix) Low/High voltage, reverse polarity, overload and short circuit protection inbuilt in fixture (xx) IP-20 . (xxi) Test certificates to be submitted before commencement of work/ claiming for payment . (xxii) Warranty certificate for minimum 2 years to be submitted from OEM.

S&F LED Lamp 230 volts,50 Hz,inverter LED 9 watt ,lumen 900 lm, rated current 0.045A, CRI less than 80, Charging time 8 to 10 Hours, operating temperature -10 to 50 degree celcius,back time 04 Hours, complete all as specififed and direccted.

Supply and fix bldg security light fittings with LED security light fittings 25 watt, IP 65 having pressure die cast aluminium alloy housing, prismatic polycarbonate cover complete including making connection with 3 core copper flexible cable of suitable size including galvanised iron pipe bracket 0.90 metre long of 25 mm dia and fixing with bldg for fixing of street light fitting all as directed. Notes :- (i) Contractor shall produce LM79 & LM 80 test report from OEM owned NABL accredited laboratory. (ii) Contractor shall give guarantee/ warranty of complete fitting/ fixture for minimum 2 years from the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of the material at no extra cost. (iv) Contractor shall arrange complete material at site for approval of GE before incorporation in the work. (v) Driver shall be IP 66 degree of protection potted seal type with inbuilt SPD and external SPD of capacity 10 KV to be provided in addition to inbuilt.

M&L Lamp holder Polycarbonate type with back plate having matching colour to holder for angle/batten fittings complete all as specified and directed.

S&F in single pole and neutral enclosure with a two pin and earth plug and socket complete with including one single pole MCB 240V, 20Amp complete all as specified and directed

Supply & Fix Ceiling fan AC single phase 230/240 volts of size 1200 mm sweep complete (BLDC) type BEE 5 star rated including blade ,down rod etc including connecting to ceiling rose all as required or directed. Note: Test report and Warranty certificate from OEM for minimum 2 years to be submitted before claiming for payment.

Supply & Fix Exhaust fan AC sinlge phase 230/240 volts of size 300 mm sweep steel body with louvre including connecting to ceiling rose all as required or directed including connecting to ceiling rose all as required or directed.Note: Test report and Warranty certificate from OEM for minimum 2 years to be submitted before claiming for payment.

Supply & Ventilation fan AC sinlge phase 230/240 volts of size 200 mm sweep having plastic body with louvre including connecting to ceiling rose all as required or directed including connecting to ceiling rose all as required or directed.Note: Test report and Warranty certificate from OEM for minimum 2 years to be submitted before claiming for payment.

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 4 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 4 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 4 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 4 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) Test certificates of cables to be submitted before commencement of work/ claiming for payment. (iv) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement. (v) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 6 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 6 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 6 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 6 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) Test certificates of cables to be submitted before commencement of work/ claiming for payment. (iv) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement. (v) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment

Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanized earh lead wire of size 4.0 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3 of SSR Part I, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI medium grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame, necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. Note: The rate quoted include cost of 7.5 metre earthing wire with protection pipe.

Supply laying jointing and testing LT XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25sqmm 4 core complete all as specified. Note : Earth work , sand cushioning, GI pipe , brick covering for mechanical protection will be measured and paid separately under respective item of Schedule.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation laying poles, stay assembly and laying of LT/HT cables in any type of soil and getting out, complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

Removal of excavated material (soil) to a distance not exc 50m and depositing where directed at a level not exceeding 1.5mtr above starting point complete all as specified and directed

M & L Dry sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed. Note:- 1.Dry fine sand of best available quality shall be used. 2.Punned thickness shall be made and paid.

M & L Sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

M&L for in replacement of existing UNSV cable end termination out door, heat shrinkable type suitable for XLPE/ PVC cables of size 25 sqmm 4 core core with working voltage 1100 volts.

M & L GI pipe medium grade 40 mm bore with all fittings for cable protection fixed to walls/ poles or laid in trenches, under road/ under culvert/ under path/ under floor /on wall etc with fixing clamps, nuts bolts etc all as specified.

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

JAGIR CONSTRUCTION CO

jagdambe traders

malghotra construction co