Repair to Joinery, Brick work, Plaster, Water Supply Items and Sanitary Items in OTM Accn and Misc Repair and Certain B/R works under AGE B/R-II of GE (N) Bikaner at Mil Stn Bikaner

Amount

Demolition of brick work built in cement mortar or stone/ boulder masonry, built in lime mortar including all quoins, arches, pillars etc all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness all as specified.

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each and removing from site complete all as specified and as directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exc 1.5 Sqm and not exceeding 4 Sqm each and removing from site complete all as specified and as directed by Engineer-in-Charge.

Taking down door shutter of any description exceeding 01 Sqm but not exceeding 02 sqm and removing from site complete all as specified and as directed by Engineer-in-Charge.

Taking down door shutter of any description not exceeding 01 Sqm each and removing from site complete all as specified and as directed by Engineer-in-Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings.

Disconnecting existing tanks,setting aside (or lowering if required) for repairs, cleaning, etc. and hositing if required reconnecting and re-fixing in position.Exc 500 Litre & n exc 1000 Litre (Cleaning repairing etc. measured separately).

Dismalting of old unservcieable aluminium snap grid false ceiling complete all as specified and directed by Engineer-in-Charge.

M & L Brick work with fly ash bricks (old size) straight or curved on plan exc 6m mean radius built in Cement and sand mortar 1:6 complete all as specified and directed.

M & L Rendering 15mm thick on wall in cement mortar 1:6 finished even & smooth without using extra cement using liquid water proofing compound all as specified

M & L Rendering 10mm thick on wall in cement mortar 1:6 finished even & smooth without using extra cement all as specified

Supply only Liquid water proofing compound.

M & L 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate, including finishing surface of concrete topping even and rough as in sub base complete all as specified and as directed by EIC.

M & L 18 to 20 mm thick machine cut kota stone slab as in flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 20mm thick screed bed in cement and sand mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

M & L 18 to 20 mm thick machine cut kota stone slab as in skirting/dado etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 10mm thick screed bed in cement and sand mortar 1:4 complete all as specified

M & L Vitrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, laid over & including screed bedding 15 mm thick in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified.

M & L Non Skid coloured ceramic tiles 7 to 8mm thick in floors, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm laid over & including screed bedding 15 mm thick in cement mortar 1:6 etc. set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified.

M & L Non Skid coloured ceramic tiles 7 to 8mm thick in floors, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm. laid over & including screed bedding 15 mm thick in cement mortar 1:6 etc. set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified.

M & L Glazed coloured ceramic tiles 300mmx200mmx7mm thick on vertical surfaces such as skirting, dados and risers to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over & including 10 mm thick cement plaster in CM 1:4 all as specified.

M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade laid over 50mm thick sand cushioning all as specified.

M & L Chequered cement concrete tiles 25 cm x 25 cm x 22mm thick with grey cement and pigment machine pressed, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed in cement and sand mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

S & F in replacement Steel windows, with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded including one shop coat of red oxide Zinc chrome primer including making good disturbed surfaces of walls, complete all as specified.

S & F in replacement Steel windows, with side hung shutters including projecting type hinges with steel handle and steel peg stay complete without glazing bars dovetailed or welded including one shop coat of red oxide Zinc chrome primer including making good disturbed surfaces of walls, complete all as specified.

S & F 35 mm thick plain framed, panelled shutter (two panel) with lock rail using 2nd class H.W (Siras or any second class Hard wood as approved by GE ), kiln seasoned and chemically pressure treated, the size of rail and style as per IS:1003 (Part-I) and panel insert of 9mm thick BWP Phenol formaldehyde bonded commercial facing ply wood, all as specified.

S & F 35mm thick glazed/ wire gauged/skeleton shutter (well kiln seasoned) 2nd class hard wood (Siras or any second class Hard wood as approved by GE), the size of rails and styles as per IS, chemically pressure treated in factory against termite infestation prepared to receive wire gauge or glass (without sash bars), edges of frame chamfered or rounded, fitted with cut and mitered beads, all as specified. Note: Wire gauge/glazing to be measured and paid separately).

Mild steel Framed work such as steel gates, chowkhats and other similar works of angle or other section with gusset plates rails, braces etc, complete, drilled for fixing of steel sheeting or other covering etc. conforming to Fe – 290 Gde E-165 complete including taking down existing gate all as specified and as directed by Engineer-in-Charge

Mild steel frame work such as grills, grating etc. with ends of bars shouldered and or riveted, or forged into spikes : framed guard bars, barred iron doors, ladders, railings and similar work conforming to Fe – 290 Gde E-165 complete all as specified and as directed by Engineer-in-Charge.

S & F Factory made Solid PVC door frame of size 50 x 47 mm , made out of 5mm plain coloured PVC sheet reinforced with MS square tube fixed in opening complete as per manufacturer's specifications and making good the disturbed surfaces with plastering in CM 1:6 and the rate quoted is inclusive this element, noting extra shall be paid on this account complete all as specified.

S & F 30mm thick factory made PVC solid panel PVC door, shutter conforming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 gauge thickness & size 19x19mm for stiles and 15 x15mmfor top & bottom rails, MS frame shall have a coat of red oxide primer of approved make and shall 'be covered with 5mm thick heat moulded PVC 'C' channel of size 30x50mm forming styles, and 5mm thick, 75mm wide PVC sheets for top rail, lock rail & bottom rail on either side, and 10mm (5mmx2)thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail panelling of 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with 30mm wide x 5mm thick PVC sheet beading on either side and jointed together with solvent cement adhesive and an additional 5mm thick PVC strip of 20mm width is to be struck on the interior side of 'C' Channel using PVC solvent adhesive complete as per manufacture’s specifications & drawings, all as directed by Engineer-in-Charge.

S & F 35mm thick flush shutters, ISI marked, solid core construction, with block board core and plywood face panels, commercial face panels, commercial type on both sides all as specified.

M & L Preparation of new plastered surface and applying two coats of white wash on wall complete all as specified and as directed by Engr-in-Charge.

M & L Preparation of new plastered surface and applying two coats of distemper oil emulsion on wall complete all as specified and as directed by Engr-in-Charge.

M & L Preparation of new plastered surface and two coats of cement base paint over a coat of primer as per maufacturer's instructions complete all as specified and as directed by Engr-in-Charge

Preparation of old decorative concrete, plastered/ un-plastered surface by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying two coats of white wash on walls all as specified.

Preparation of new decorative concrete, plastered/ un-plastered surface by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying two coats of cement base paint on walls all as specified.

S& F mild steel medium weight Butt hinges 100mm long and fixed with steel screws complete all as specified.

S&F mild steel Tower Bolt 150mm long stove enameled black with bright bolt complete all as specified.

S&F Mild steel pressed handles, 150 mm long, oval type, stove enamelled, black, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F MS sliding door bolt, plate type, stove enamelled, black with bright bolt not less than 12mm dia, length of bolt 250mm, including a minimum of 6 bolts, nuts and washers, four on bolt plate and two on staple plate complete all as specified.

S&F Mild steel galvanised wire cloth 0.56mm nominal dia of wire and 1.18 mm average width of aperture fixed with tinned tacks or galvanised wire staple complete all as specified.

S&F in repairs Mild steel galvanised wire cloth 0.56mm nominal dia of wire and 1.18 mm average width of aperture fixed with tinned tacks or galvanised wire staple complete all as specified.

S & F Sheet glass 3mm thick, ordinary quality & glazing with oil putty in squares n.exc 0.5sqm in each pane all as directed by Engineer-in -charge.

S & F in repairs Sheet glass 3mm thick, ordinary quality & glazing with oil putty in squares n.exc 0.5sqm in each pane all as directed by Engineer-in -charge.

M & L PCC 75 mm thick in 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection finished the surface even and fairwithout using extra cement all as specified

S&F in repairs PVC grating 125 mm dia all as specified. ( Minimum Wt 40 Gm). Make:- Prayag or equivalent

S&F in repairs PVC waste pipe of best quality for urinal as per sample kept in AGE office all as specified.

S&F in repairs PVC waste pipe of best quality for WHB as per sample kept in AGE office all as specified.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm all as specified.

S&F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls all as specified

S&F in repairs 110mm bore PVC (SWR) bends any radius all as specified.

S&F in repair 15mm bore stop valve, cast copper alloy, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-charge.

S&F in repair 20mm bore stop valve, cast copper alloy, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-charge.

S&F in repair Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, for 15mm bore GI pipe , complete all as specified and as directed by Engineer-in-Charge.

S&F in repair bib tap 15 mm bore, high pressure of PTMT (minimum weight 90 gms) any colour screwed for iron pipe and fixed all as specified. Make:- Prayag or equivalent .

S & F in replacement wash hand basin vitreous china, size 550mm x 400mm, white, flat back, including CI brackets, pillar tap, cast copper alloy, with capstan heads, chromium plated, PVC connection, PVC waste and waste pipe 32 mm dia with brass coupling, PVC grating including pinning in ends of brackets etc all as specified.

S & F in replacement Vitreous China squatting pan, of ‘Orissa pattern ‘ white of size 580 X 440 mm, with integral foot rests and 'P' or 'S' trap including provision of lime concrete bedding minimum 150 mm thick (1 lime, 2 sand or surkhi and 5 aggregate) complete all as specified.

S& F in replacement Vitreous China wash down water closet pan (pedestal pattern) complete all as specified.

S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)

S & F in replacement PVC 10 ltrs , valveless, syphonic action type, flushing cistern, white, low level, with inlet, ball valve, float and handle, including 32 mm bore flush pipe brackets all as specified.

S&F anodised aluminium snap grid frame work of size 605 x 605 mm for false ceiling including necessary notching. The snap grid shall consist of anodised aluminium main & cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/RM and 23.5 x 26.4 x 1.40 mm weighing 0.191 Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminium angle bracket of size 15mm x 15mm x 1.5 mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washer. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminium angle of size 40 x 25 x 2 mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and providing 12 mm thick AC plain boards in grid fixed as false ceiling grid made of aluminium as per specification and providing two coats of synthetic enamel paint over a coat of pink primer including preparation to exposed surfaces complete all as specified and directed.

M & L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with L-type or J-type or cranked hook bolts all as specified.

M & L Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with L-type or J-type or cranked hook bolts all as specified.

S & F in replacement Rotational moulded polyethylene water storage tanks of capacity 500 litres, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed by Engineer-in-Charge. (Notes : (i) The water storage tanks shall be 3 layers, HDPE tanks moulded to seem-less perfection of rotational moulding process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water. (ii) The tanks shall be white coloured with three layered wall and shall be ISI marked. Also refer paras 18.60 and 18.60 A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. However cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30 cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements and as directed by the Engineer-in-Charge shall be deemed to be included in the unit rate of this item.(iv) HDPE storage tanks shall be procured from the manufacturers as per Appendix “D”.)

S & F in replacement Rotational moulded polyethylene water storage tanks of capacity 1000 litres, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed by Engineer-in-Charge. (Notes : (i) The water storage tanks shall be 3 layers, HDPE tanks moulded to seem-less perfection of rotational moulding process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water. (ii) The tanks shall be white coloured with three layered wall and shall be ISI marked. Also refer paras 18.60 and 18.60 A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. However cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30 cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements and as directed by the Engineer-in-Charge shall be deemed to be included in the unit rate of this item.(iv) HDPE storage tanks shall be procured from the manufacturers as per Appendix “D”.)

S & F in replacement Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified and as directed by Engineer-in-Charge. Make : PRAYAG/ POLYTUF / SHAKTI

S&F aluminum anodised cast type handles 150mm size complete all as specified and as directed by Engineer-in-Charge.

S&F 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws of size 125mm complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Mortice lock, vertical type, size 100mm ,4 levers brass metallic complete all as specified.

S&F Mortice lock, vertical type, size 100mm ,4 levers brass metallic complete all as specified.

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F Floor door stopper 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed by Engineer-in-Charge.

S & F Aluminium extruded section Door closer hydraulically regulateld, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35kg and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Floor door stopper150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed by Engineer-in-Charge.

S & F Sheet glass 4mm thick, ordinary quality & glazing with oil putty, aluminium beading and wooden beads one side frosted in squares in each pane all as directed by Engineer-in -charge.

M&L preparation of new wooden surfaces over 10 cm width or girth of any description and applying two coat of synthetic enamel paint over a coat of pink primer all as specified.

M&L preparation of new steel surfaces over 10 cm width or girth of any description and applying two coat of synthetic enamel paint over a coat red oxide zinc chrome primer .

S & F in replacement 6 mm thick AC designer board of size 605 mm x 605 mm as in false ceiling complete all as specified and directed by Engineer-In-Charge. Make :- Everest or equivalent.

S&F powder coated Aluminium work in frame of door, windows and partitions, shutter for door and window and partition wall incl aluminium beading, jointing clits etc. complete fittings all as specified and directed by Engineer-in-Charge.

S&F in replacement 5.5 mm thick tinted glass type fitted with rubber gasket complete all as specified and directed by Engineer-in-Charge

S&F 5.5 mm thick plain glass type fitted with rubber gasket complete all as specified and directed by Engineer-in-Charge

S & F sun control film 25micron reflective type (gareware sun control or equivalent) complete as specified

S & F 30 mm thickness aluminium body with plate size 25x65 mm pivot made of aluminium for aluminium door shutter complete as specified

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store as directed complete.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store as directed complete.

S & F GI tubing 15 mm dia, medium grade and fixed to wall and ceiling or laid in floor with all fittings complete all as specified & directed.

Refixing 15mm bore old steel tubing and connections , in new or old position (walls, ceiling, floors, etc) complete. ( The old serviceable GI pipes retrived from SI No 89.00 shall be used under this items in new or Old position with fittings)

M&L for 20mm bore Steel water tubes, medium grade, ISI marked, galvanised, with all fittings, fixed to walls and ceiling or laid in floors complete.

Refixing old 20mm bore steel tubing and connections , in new or old position (walls, ceiling, floors, etc) complete. ( The old serviceable GI pipes retrived from SI No 90.00 shall be used under this items in new or Old position with fittings)

S & F 1.25 mm thick Pressed steel frames of size 105mm x 60mm for single doors including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S & F 1.25 mm thick Pressed steel frames of size 125mm x 60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M & L PCC 1:3:6 type C1 using 20 mm graded stone aggregate for embedding the hold fast, copping etc complete all as specified & directed.

M & L PVC floor trap 75mm incl.CP grating complete all as specified and as directed.

S & F Asbestos cement sheet 6 mm thick corrugated or semi corrugated fixed in roof covering complete all as specified & directed.

S & F Asbestos cement sheet 6 mm thick plain sheet angular for ridge fixed with coach screws or J type hooks etc complete all as specified & directed.

S & F in repair angle valve cock chromium plated fancy type half/full turn for iron pipe 15 mm bore screwed down high pressure, with capstan head, screwed both ends for iron pipe or for union complete all as specified & directed.

S & F in repair chromium plated shower rose with or without swivel joints 75 mm size of flange including fixing to pipe or union complete all as specified & directed.

S&F in replacement Health fauset chromium plated with and including 1.5 metre long CP flexible pipe and CP brass nuts,for bore of pipe 15 mm suitable for EWC complete all as specified.

S&F 300 mm, ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete.

S & F Tubular towel rail of aluminium anodised, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S & F in repair gun metal glob or gate valve with iron wheel head , crewed for iron pipe of 20 mm dia fixed in repair complete all as specified & directed.

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete.

S&F Steel ventilators with top hung shutter including projecting type hinges, steel peg stay complete all as specified and as directed.

M & L Sand filling under floors for laying floor finishes complete as specified

Taking down and refixing in the same opening after necessary repairs, eazing and tighting work to Aluminium door (changing of beadings, flooor spring,glass, pivots etc shall be measured and paid seperatly under respective items) complete all as specified and directed by Engineer - In - Charge.

M & L for point welding in repairs not exceeding 2.5 CM in length and not exceeding 6mm thick complete in door , window and ventilator hinges or as directed by Engineer - In - Charge.

S&F mild steel medium weight Butt hinges 75mm long and fixed with steel screws complete all as specified

M&L preparation of new steel surfaces over 10 cm width or girth of any description and applying two coat of synthetic enamel paint complete all as specified.

N.K. CONSTRUCTION COMPANY

SHREE GURU NANAK CONSTRUCTION COMPANY

Satish kumar and company

durga construction company

MITTAL ENTERPRISES