CERTAIN SPECIAL REPAIRS AND REVENUE WORK AT AMRITSAR CANTT

Amount

B/R PORTION Dismantling Asbestos cement ( corrugated, semicorrugated ,etc.) sheets in roof coverings

Dismantling boarding , any description , fixed in any position with screws

Dismantling RCC purlins in suspended works all as specified and directed

M&L for Providing and fixing Gypsum board 12 mm thick in ceiling fixed with screw as per manufacturers instructions incl preparation of new surfaces & applying two coat of OBD on ceiling as specified and directed by Engr-in-charge

S&F GI frame work for seameless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws as 450mm centre to centr/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre.

S&F Hangers 2 mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified.

S&F mild steel Gde Fe-410-W as in roof trusses, (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee,angle,channel, hollow tube or flat sections) including distance pieces , cleats etc including welding of joint as per the direction given by Engr in charge

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

M&L for preparation of untreated steel/iron surfaces of any description , over 10 cm in width or girth, not otherwise described and applying two coats of sythetic enamel paint over and incl one coat of red oxide primer.

M&L for PCC 1:2:4 type B-0(using 12.5mm graded stone aggregates) as in roof padding of average 50mm thick, roof kerbs or mud stops, rounded or chamfered on edges and like including weathering slight rounded and throating complete all as specified and directed

Taking down cement plaster of any description on brick walls, etc including raking out joints, hacking for key scrubbing down with water etc

Demolition of brickwork, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed

M&L for Brick work with sub class "B: bricks straight or curved on plan exc 6 m mean radius in CM 1:4.

All as per Srl item No 13 above but except bricks (old dismantled serviceable bricks obtained from Srl item No 12 shall be reused after necessary cleaning of mortar)

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 and finishing even and smooth without using extra cement.Complete all as specified and directed.

All as per Srl item No 15 above but in CM 1:6.

Material and Labour for preparation of new/old plastered/unplastered surfaces and applying two coats of oil bound distemper over coat of primer on walls complete all as specified.

Material and Labour for preparation of new/old plastered/unplastered surfaces and applying two coats of cement base paint of shade as approved over a coat of cement primer on wall surfaces complete all as specified.

Dismantling Brick tiles or terracing tiles, single layer on roofs complete all as specified and directed

Demolition mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed by Engr-in-Charge

M&L for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including cleaning surfaces etc complete all as specified and directed

S&F minimum 3 mm thick APP Film based polymeric membrane minimum weighing 3 Kg per Sqm reinforced with polyster non woven polyster (weight not less than 150 gms/sqm) laid over bituminous primer of 0.3 Kg/Sqm and with complete torch application including sealing of joints 100 mm along width and 75 mm along length of membrane after cleaning down the roof by brooms complette all as specified and directed.

M&L for 40 mm thick brick tiles laid on 15mm thick cement mortar 1:6 and joints grouted flush in cement mortar ( 1:3) and pointing in CM 1:3 mixed with 5 % of crude oil by weight of cement complete all as specified and directed

All a per Srl item No 23 above but except tiles (old serviceable dismantled tiles obtained from Srl item No 19 shall be reused after necessary cleaning of mortar)

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:3. finishing even and smooth without using extra cement complete all as specified and directed For struts in patch.

M&L for three coats of white wash on plaster surface of ceiling including prepration of surface.

Taking down Chowkats or frames from the opening of size not exceeding 1.5 sqm each with shutters ( without taking off shutters from the frames) complete all as specified and directed

All as per Srl item No 27 above but size of opening exceeding 1.5 Sqmtr but not exceeding 4 Sqmtr

Material and labour for Box type steel window made of ERW tube P-section of size 60mmX25mm double frame, comprises of glazed Skelton & gauzed shutter of ERW tube P-section size 50mmX20mm with one/two Nos openable leaf consisting of two nos sash bar of T-section 20mmX3mm welded to frame with one No vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/screwed to frame for fixing of glass including fittings and fixtures like Handle, Tower bolts, Stopper, Cleat, Pintal hinges, holdfast etc as given below all as shown on drg No CEJZ/TD 1020/08 Sh 1/3 to 3/3 dt 01 May 2008 complete including cutting holes, making good dismantled portion in PCC 1:2:4 type B-1 complete all as specified and directed. (a)Hold fast,150mm long of 12mmX3mm MS flat-04Nos per window (b) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (c) MS Tower bolt 150mm long-02 Nos/leaf (d) Z Section stopper 20mmX25mm,100mm long -01 No per leaf (e) Cleat 55mm long of hollow square 15mmX12mm-02 Nos per leaf Note:- 1. Wire guage, Sheet glass, guard bar and painting shall be measured and paid separetely. 2. Mode of measurement for this item shall be for window portion only excluding ventilator portion where ever shown in drawing.

S&F MS box type window/ventilator fixed type with glazing bar without wire work and glass as per Drg No CE JZ-70/06-07 dated 07.06.07 with guard bar including priming coat complete all as specified and directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F framed work as door, chowkhats, and Grill gates of angle frame work fixed with Nut & bolt to wall or other section complete drilling or fixing welding be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also festering and fixing complete.

M&L two coats of synthetic enamel painting on steel surfaces of any description over 10 cm in width or girth not otherwise described including prepration of previously untreated surfaces

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2,3 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face &2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing.

S&F pressed steel frames 1.25mm thick for door size of frame 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges complete all as specified and directed.

S&F IInd class hard wood Glazed and skeleton shutters 35mm thick divided into square, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a) ; supplied and fitted to chowkats complete all as specified and directed

S&F factory made 35 mm thick flush shutters solid core construction with block board core and plywood face panels.

M&L two coats of synthetic enamel painting on wooden surfaces of any description over 10 cm in width or girth not otherwise described including prepration of previously untreated surfaces.

S&F Floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed to door shutter of size 140mm.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed

S&F Sheet glass, 3mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane including wooden beading fixed nails including hacking at old glass complete all as specified and directed

All as per Srl item No 41 above but figured glass pin head type & glazing with oil putty

S&F in repair 150mm long aluminium anodised tower bolts,with bright bolt and fixed

S&F 150mm long aluminium anodised handle, oval type, complete all as specified and directed

Supply only butt Hinges, 100mm size, medium weight, cold rolled mild steel complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding and rubbish off the premises. Complete all as specified.

S&F glazed ceramic dark coloured tiles 450x300mmx7mm thick, etc. on vertical surfaces such as skirting , dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:4 on brick surface complete all as specified and directed.

M&L for vitrified light Ceramic tiles 10mm thick (Square/rectangular) polished, area of each tile not exceeding 0.36sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over and including 15mm thick screed bed in cement mortar 1:6.

S&F in repairs vitreous china wash down water closet pan pedestal pattern white including fixing bolts and seat cover white for pedestal pan with flat bottom and cover and mild steel chromium plated hinging device (excluding flushing cistern and flush pipe).

Supply only 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve flote handle including bracket complete all as specified and directed

Supply only Flush pipe of polythylene of low or high density or PVC,32mm dia for low level cistern.

S&F in Repair vitreous China wash basin white,flat back size550x400mm including PTMT waste coupling 32mm bore, complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm.

Dismantling water tanks Exc 250 Ltr & not exceeding 500Ltr and S&F rotational moulded polythene, triple layers, water storage tank 500 Ltr capacity, closed top, cylindrical, hoisted and fixed in position including S&F 20mm bore PTMT ball valve epoxy coated minium weight 210gms with aluminium rod complete all as specified and directed

Taking down or up steel tubing 15mm bore and connections and supplying, fixing and testing galvanised steel tubing 15mm bore “medium grade” with all fittings complete fixed to wall/ ceiling or laid in floors complete all as specified and directed

All as per Srl item No 55 above but 20mm bore of pipe

S&F in repair stop valves, 15mm bore cast copper alloy, chromium plated, screwed down , high pressure, with crutch or butterfly handles , screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F in repair of brass cromium brass plated fancy type bib taps 15 mm bore long nose screwed down screwed for iron pipe or for brass complete all as specified and directed

S&F in repairs 125mm CP shower rose fancy type with CP armincluding fixing to steel pipe or for union for 15mm bore pipe complete all as specified and directed.

S&F in repairs 100mm dia CP grating with or without hinge type or hole type complete all specified and directed.

Taking down eaves gutters and rain water pipes ( any size or pattern) , including all fittings , heads, shoes, bends, swan necks, etc.,complete all as specified and directed

S&F 110mm bore PVC(SWR) pipes single socketed in any length fixed to walls with dash true nut and bolt at every 2mtr length including) including all fittings complete all as specified and directed by Engineer-in-charge Make:-supremo,Finolex,Jyoti.

All as per Srl Item No 63 above but laid in trench or in floor

S&F 110mm bore PVC (SWR) bends any radius With access door

Demolition of cement concrete in ground floors and paving not exceeding 15 cm thickness ( below or above ground level) and disposing the rubbish to a distance exceeding 50 Mtr but not exceeding 100 Mtr away to low lying areas complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate as in plinth protection finishing fair and even.

M&L for Chequred cement concrete tiles 30 cm x 30 cm x 25 mm thick set and jointed and pointed in neat cement slurry in floors with grey cement and no pigment over & including screed bed 15 mm thick in CM 1:6.including taking down of existing treatment and removing rubbish to low lying areas to a distance exceeding 50 mtr but not exceeding 100 mtr away.

Demolition reinforced roofs, floors (other than ground floors), beams staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition)

M&L for reinforced Cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregates) as in chajjas, facia and the like complete all as specified and directed.

Use and waste of formwork to Chullah hoods, chajjas, weather shades, corbels, water troughs and similar items including edges rough finished surfaces of concrete complete all as specified and directed

S&F mild steel TMT bars 10 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. Or securing with clips complete all as specified and directed

S&F 110mm bore( SWR) vent cowl

M&L 110mm bore PVC (SWR) floor trap ,plain with grating including jointing with solvent cement

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed make-Godrej

Taking down wooden shtters of size exc 1 sqm and not exc 2 sqm each and Refixing in the same opening by easing and adjusting with new Butt hinges of 100mm size of medium weight complete all as specified and directed.

All as per Item No 76 above but size exc 25 Sqmm each.

E/M PORTION Point wiring complete with 1.5 Sq mm (nominal area)FRLS PVC insulated un-sheathed and stranded copper conductor cable I SI marked and including PVC concealed conduit SSI marked ot size 25 mm dia and 1.5 mm wail thickness and conduit fittings including FRLS PVC insulated unsheathed 1.5 Sqmm copper earth wire to common earth and connecting to earth dolly and Metal Flush box, cover plate with frame of suitable size for fixing modular switches/sockets/fan regulator etc complete all as specified for the following (Note : Cost of Metal boxes and modular accessories like cover plates will be included in quoated rate.) Make of wire Havells/Polycab/RR Kabel (a) Fan point/ exhaust fan point / one light point / bell/ buzzer controlled by one switch/ bell push.

All as per Srl item No 78 above but for one socket outet point 5 amps on the same board.

All as per Srl item No 78 above but for one socket outet point 5 amps on the independent board.

All as Ser item 78 here in before but with 2.5 sq mm wire and earth wire of 1.5 sq mm for 3 Pin 15 Amp modular type socket outlet. Note : Point wiring for power point will not be mixed with liqht/fan point circuit or not in the same conduit pipe.

Supply and Fixing Modular switch 6 Amp 1 way 1 module size complete ail as specified and as directed bv Enar-in-Charae. Make Havells/lndo Asian/C&S

Supply and Fixing Modular switch 16 Amp 1 way with indicator 1 module size complete ail as specified and as directed by Engr-in-Charge. Make Havells/lndo Asian/C&S

Supply and Fixing Modular socket shuttered 6 Amp 2/3 pin combined 2 module size complete all as specified and as directed by Engr-in-Charge. Make Havells/lndo Asian/C&S.

Supply and Fixing Modular socket 16Amp multipurpose type 2 module size complete all as specified and as directed by Engr-in-Charge. Make Havells/lndo Asian/C&S

Supply and Fixing Modular Fan regulator step type 120 watts 2 Module size complete all as specified and as directed by Engr-in-Charge.Make Havells/lndo Asian/C&S

Supply and Fixing Modular blank plate 1 Module size complete all as specified and as directed by Engr-in-Charge. Make Havells/lndo Asian/C&S

S&F bell push, Module type, single pole 5 amps complete all as specified and directed. Make Havells/indo Asian/C&S

Supply and fixing of single phase call bell ‘DING DONG’, AC 230 volts single pole fixed over and including pressed steel sunk box of size 175 X 100 mm duly covered with 3 mm thick bakelite sheet complete all as specified and directed. Make

S & F lamp holder insulated body angular type with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size & MS box of suitable size and making good surface as original by plastering and whitewash/colour/distemper etc complete all as specified and directed

S & F Ceiling rose, surface bakelite 3 terminal, 240 volts, 5 Amps with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size & MS box of suitable size and making good surface as original by plastering and whitewash/colour/distemper etc complete all as specified.

S & F in repair MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, 'B' curve type complete all as specified and directed. Make Havells/C&S/L&T

S & F in repair MCB double pole, 240 volts, 40 to 63 Ampere, rupturing capacity 10 KA, 'B' curve type complete all as specified and directed. Make Havells/C&S/L&T

S&F Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified. (Note : cost of removing old wooden box and making good of surface as original by brick work, plastering, whitewash/colour/distemper etc is included in quoted rate) Make Havells/C&S/L&T.

Blanking plate of plastic (suitable for distribution board).

S & F in repair wall /ceiling mounting LED 20 Watt high quality extruted tube light fitting complete with all acessories 1x18 Watt LED , suitable for domestic application, 240 Volts, 50 Hz, including one tube rod and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete all as specified and directed. Make Havells/C&S/L&T.

S & F 40 mm bore light grade galvanised iron tubing with all necessary Gl fittings as in protection pipe of cable, fixed to pole or laid under floor/ground / under road crossings for protection of cable complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 meters wide and not exceeding 1.5 meter depth for foundation for LT cables complete all as specified and as directed.

Returning filling in trenches including spreading leveling watering and well ramming in layers each not exceeding 25 cm in soft/loose soil complete all as specified

Removing surplus spoil to a distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.5 meters above the starting point, complete all as specified

M&L for Sand cushioning to UG cable 40cm wide 15cm and 10cm thick above and below the cable in trenches/ducts complete all as specified and directed by Engineer-in-Charge. Note : Thickness after punning down shall be measured

Supply and laying burnt brick sub class 'B' modular size, for cable protection laid length wise perpendicular to the axis of cable complete all as specified and directed.

M & L for laying of LT cable of 1100 volt XLPE insulated and PVC sheathed of size 25 sqmm 4 core with cable gland including taking down old unserviceble cable complete all as specified and directed by Engineer-in-Charge.

Material and labour for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions connected with galvanised iron earth lead of size 4mm by means of galvanised nuts, bolts & washers GI wire of 4mm dia with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed. Note : - (i) Earth lead and protection pipe beyond 7.5 m shall be measured and Paid separately. (ii) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt.

Taking down old unserviceable point wiring any type from existing conduit (light, fan, socket or power point etc) complete such as switches, ceiling rose, pendent, regulator and socket etc and removing the material FRLSom site and making good the disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, whitewash/colour/distemper etc complete all as complete all as specified and directed.

M & L for sub main wiring with 1100 volt grade two single core PVC insulated and unsheathed cable with stranded copper conductor 4 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-Ill) 1983 mark, or relevant ISI mark with alt accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 2.5 sqmm multi - stranded copper conductor as earth wire in green colour complete all as specified and directed.Make of wire Havells/Polycab/RR Kabel

S&F MCCB Incomer distribution board double door vertical type made out of CRCA MS sheet surface with insulated material like polyester or with epoxy powder coating surface mounting TPN 4 way, 415 volts with copper bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB and IP 43 - IK 09 protection with and incl 100 amp 36 kA 4 pole MCCB with thermal - magnetic setting and Icu = Ics= 100% complete all as specified. (Note : The cost of removing old wooden box and making good of surface as original by brick work, plastering, whifewash/Colour/distemper etc. is included in quoted rate) Make Havells/L&T/C&S.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with double pole MCB of rating 240V ,20A suitable for AC complete all as specified.

Supply and fix in replacement of security light fitting LED 25 Watt Including Gl bracket of suitable size and accessories complete mounted on suitable type light grade bracket upto 1 0 mtr long bent to shape, mounted on wall with two nos 8 mm dia, 40 mm long bolts, nuts with twin washers grouted in wall including connection with 3 core PVC insulated overall sheathed flexible cable with muyltistranded copper conductor of size not less than 1.0 sq mm from celing rose to fitting terminal including taking down old CFL security light fitting all as specified and as directed Make

S& F Gl bracket fight grade Gl Pipe 1.2 mtr Length for fixing of street light fitting 36/40 Watt including connection all as specified and directed.

S&F exhaust fan 300 mm sweep including cutting of wall /window/lowers and fixing arrangement complete all as specified and directed.Make Havells/CG/Orient

M & L for laying of LT cable of 1100 volt XLPE insulated,stranded aluminium conductor and PVC sheathed of size 35 sqmm 3.5 core with cable gland complete all as specified and directed by Engineer-in-Charge. Polycab/Havells/RR Kabel.

S&F of Aluminium Lugs for LT 35 sqmm cable including cutting of LT cable suitably and removing the insulation for fixing the lug and crimping it complete all as specified and directed.

S&F of single door outdoor type IP 55 protected Bus bar enclosure of 600mmX450mmX200mm made out of 1.6mm thick CRCA Steel duly Powdered coated with an incl 100A,16 KA 4 pole MCCB with spreader terminal for fixing the cable fitted in bus bar enclosure using 200A rated aluminium Bus bar outdoor type welded to suitable size MS angle iron frame and embedded in PCC 1:2:4 type B1 complete all as specified. Height of enclosure from ground level should not less than 0.5 metre Make of MCCB Legrand/Siemens/Schiender.

m/s. gopal krishan

R D Bansal