PROVISION OF COVERED SHED FOR FURNITURE AT BSO YARD AND CERTAIN OTHER SANCTIONED WORK UNDER GE (EAST) JALANDHAR CANTT

Amount

Surface Excavation not exceeding 30cm deep and averaging 15cm deep and getting out in Soft/ Loose soil, complete all as specified and directed

Surface dressing not exceeding 15cm deep and getting out in hard/ dense soil complete all as specified and directed

Excavating in trenches n.exc 15 m wide and n.exc 1.5 m deep for foundations, etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 Sqm on plan and getting out in ordinary soft/loose soil, complete all as specified and directed

Material and labour for PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregates) lean concrete as in foundation, filling and mass concrete complete all as specified

Material and labour for brick work with flyash bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed

Material and labour for brick work with flyash brick, straight or curved on plan any radius in half brick thick walls built in CM 1:4 complete all as specified and directed

Returning filling in including, spreading, levelling, watering and well ramming in layers not exc 25 cm soft/loose soils, complete all as specified and directed

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point in soils complete all as specified and as directed

Removing excavation soil exc. 250m but n.exc 500m and depositing where directed at a level n.exe 1.5m above the starting point, complete all as specified and directed

Material and labour for rendering 12mm thick in cement mortar 1:6 on fair faces of brick walls or on concrete surfaces finished even & smooth complete all as specified and as directed

Material and labour for rendering 15mm thick in cement plaster 1:6 on fair faces of brick work or concrete surface including even & smooth surface without using extra cement, complete all as specified and directed

Material and labour for plastering in CM 1:4, 15mm thick on fair faces of brick/concrete wall surfaces and finishing fair & even complete all as specified and as directed

"Supply only" Water proofing compound (ISI Marked) complete all as specified

Material and labour for prepration of new surfaces of walls including cornices pilasters etc, applying three coat of white wash complete all as specified

Material and labour for preparation of new surfaces of wall including cornices, plasters etc (Plastered or unplastered surfaces) and applying two coats of cement base paint complete all as specified

Material and labour for 5mm thick rendering in cement mortar 1:3 on concrete surfaces, ceiling etc finished surface even complete all as specified and as directed

Material and labour for preparation of new plastered surface of ceiling including cornices pilasters etc. and applying three coat of white wash on ceiling complete all as specified and as directed

Material and labour for RCC Design Mix, M-25 (using 20mm graded aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and as directed

Material and labour for RCC Design Mix, M-25 (using 20mm graded aggregate) as in columns, pillars, piers, posts and strut like complete all as specified and as directed.

Material and labour for RCC Design Mix, M-25 (using 20mm graded aggregate) as in beams, lintels over 1.5m span and the like complete all as specified and as directed

Material and labour for RCC Design Mix, M-25 (using 20mm graded aggregate) as in slab supported on walls, beam and column in floors, roof, landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed

Material and labour RCC M-25 (Design mix) using 20mm graded stone aggregate as in chajjas, supported on walls, complete all as specified and directed.

Material and labour for formwork to sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any) of foundation and plinth beams , and similar work, vertical or to batter, flat surfaces of concrete , surface is required to be fair finished complete all as specified and as directed.

Material and labour for formwork to sides of pillars, posts, struts, piers, columns and stanchions, rectangular or polygonal surfaces of concrete, surface is required to be fair finished complete all as specified and as directed

Material and labour for formwork to sides/soffits of beams/lintel beam for rough finished surface of concrete flat, complete all as specified and directed

Use & waste for form work to soffits of suspended slab such as roof slab, floor slab , landing and similar work; not exc 200 mm thick horizontal or sloping, rough finished surface of concrete, complete all as specified and directed.

Material and labour for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n.exc 20cm wide, rough finished surface of concrete, complete all as specified and directed

Material and labour for formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished surface of concrete flat complete all as specified and directed.

Material and labour for TMT bars 10mm dia and over, cut to length, bent to shape as required including cracking bending hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and as directed

All as per Srl item No 29.00 here-in-before but 5mm dia and over upto and including 10mm dia inserting, spacers and binders

Material and labour for 75mm thick PCC (1:4:8) type D-2, (40mm grade aggregate stone aggregate) as in sub base complete all as specified and directed

Material and labour for 100mm thick PCC (1:4:8) type D-2, (40mm grade aggregate stone aggregate) as in sub base complete all as specified and directed

Material and labour for 25mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as a leveling concrete in floor finishing concrete complete all as specified and directed

Supply and fixing Non skid ceramic coloured 7 to 8 mm thick area of each tile exc 0.11 sqm but n.exc 0.18 Sqm in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed 1:6 cm complete all as specified and directed.

Supply and fixing of glazed ceramic coloured /printed tiles 450x300x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match including 10 mm thick in cm (1:4) in vertical surfaces of walls/skirting etc. complete all as specified and directed

Material and labour for hard core of broken stone or boulders of gauge n.exc 63mm deposited spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface complete all as specified and directed

Material and labour for 75mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection and making joints and filling with bitumen sand mastic including necessary formwork complete all as specified and directed

Material and labour for 12mm thick cement plaster in cement mortar (1:3) on concrete roof surfaces finished even and fair, including cleaning the roof top by water etc with WPC complete all as specified and directed

Material and labour for renderng 15mm thick in CM 1:3 on brick wall surfaces finished even and smooth using extra cement with WPC (WPC shall be measured and paid separetely) complete all as specified and directed.

Material and labour for Bitumen Primer shall be applied on plastered surface of roofs at the rate of 0.40 Kg/Sqm of Surface area of roof for use in water proofing and dump proofing treatment complete all as specified and directed

Material and labour for APP based polymeric membrane minimum weighing 3.60 Kg/sqm and minimum 3mm thick reinforced with five layer polyster non wove fabric (wt. Not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified

Material and labour for 20mm dia steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed

All as per srl item No 42.00 here-in-before but 15mm dia

Supply and fixing PVC Connections 15mm size with PTMT Nuts of length 450mm complete all as specified and as directed.

Supply and fixing 32mm dia PVC waste pipe for WHB/URINAL complete all as specified.

Supply and fixing Vitreous china urinal half stall type, white including connection to flushing pipe and outgoing pipe complete all as specified and directed

Supply and fixing vitreous china wash down water closet pan white excluding fixing bolts, flushing cistern and flush pipe with and incl 'P' or 'S' trap and all as specified and directed.

Supply and fixing vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest including CI 'P' or 'S' trap with providing lime concrete bedding and connecting to flushing cistern complete all as specified

Supply and fixing plastic seat cover white for water closet pedestal pattern closed patter with flat bottom fixed with mild steel chromium plated or aluminium hinging device complete all as specified.

Material and labour for toilet paper holder box types of chromium plated fixed to walls with chromium plated brass screws complete all as specified & directed

Material and labour for soap dish, fixed to plugs with chromium plated brass screws approximate size 160x160x90mm complete all as specified & directed

Supply and fixing PVC low level flushing cistern , white , 10 ltrs capacity with float valve and brackets complete all as specified and directed.

Supply and fixing 15mm dia bib taps fancy type cast copper alloy with Chromium plated crouch or butterfly handle screwed, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

Supply and fixing stop valves 15mm, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

Supply and fixing CP grating doom 100mm dia complete all as specified and directed.

Supply and fixing towel rail 600 mm long and 20 mm dia brass chromium plated D type fixed with screws and wooden or plastic cleats complete all as specified and directed

Supply and fixing vitreous china wash basin white flat black of size 550x 400 mm (excluding taps), waste, chain and plug including brackets complete all as specified and directed

Supply and fixing pillar taps, brass, with capston heads, fancy type, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts screwed for 15mm bore iron pipe, complete all as specified and directed

Supply and fixing 500 ltrs rotational moulded polythine water storage tanks (cylinder vertical with closed top) hoisted and fixed in position including ball brass valves, high pressure with polythene float and fly nut complete screw for iron pipe or brass ferrule all as specified in SSR Part-I

Supply and fixing ball brass valves 20mm, high pressure, with polythene float and fly nut complete screwed for pipes or brass ferrule and fixed complete all as specified and directed

Supply and fixing 20mm dia gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed

Material and labour for PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as directed

Supply and fixing PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 75mm dia incl necessary clamp complete all as specified and directed

Supply and fixing PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 110mm dia on laid in floors/ trenches with & including existing/ new MS stack clamps of FI 50 x 3mm complete all as specified and directed

Supply and fixing PVC (SWR) bends any radius 75mm dia complete all as specified and directed

Supply and fixing PVC (SWR) bends any radius 110mm dia complete all as specified and directed

Supply and fixing PVC (SWR) branch piece, double (double Y) equal or unequal for 75mm dia complete all as specified and directed.

Supply and fixing PVC (SWR) vent cowl 75mm dia complete all as specified and directed

Supply and fixing 110mm PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed

Supply and fixing 110mm PVC (SWR) floor/ nahani traps, plain with grating incluidng jointing with solvent cement complete all as specified and directed

Supply and fixing steel window/ ventilator 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises glazed skeleton shutter ERW sec 50mm x 20mm and 1mm thick with two openable leaf consisting two Nos sash bars of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion PCC (1:2:4) type B-1 four Nos for each window) including following fittings welded to frame shutter:- (a) Hold fast, 150mm long of 12mm x 3mm made to shape-04 Nos per window. (b) Handle of z section 20mm x 25mm, 100mm long 01 No per leaf. (c) MS tower bolt 150mm long- 2 Nos per leaf. (d) z section 20mm x 25mm, 100mm long stopper - 01 No per leaf. (e) MS pintal hinges of size 75mm x 12mm- 2 Nos per leaf. (f) Fabrication & fixing arrangement as per Drg No CEJZ/TD-06/07. Note: Grill/ flat iron and glass panes/ wire mesh shall be measured and paid separately under respective item of this BOQ.

Ditto All as per srl item No. 72.00 above but gauged shutters without sash bars complete.

Supply and fixing Figured Glass 3.0 mm thick, Pin Head type and glazing with Wooden Beads or Oil Putty in Square or Rectangular, not exc. 0.50 Sqm, complete all as specified and as directed.

Supply and fixing sheet glass, ordinary quality 3mm thick fixed with oil putty size of glass not exc 0.50 sqm in each pane, complete all as specified and directed

Material and labour for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

Supply and fixing mild steel framed work such as guard bars/grills, grating etc with end of bars shouldered and/or riveted or forged into spikes; framed guard bar; barred iron door; ladder frame baluster; walk ways railing; framework of water tank and similar works including one shop coat of zinc chromate primer complete all as specified

Supply and fixing PVC door frame size 50mm x 47mm made out of 5mm of plain colour PVC sheet & edges wil be painted to match with prelam sheet, reinforce with MS square tube supplying & fixing in opening as per specification as directed

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. M,S frame shall be covered with heat moulded plain PVC sheet, channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side prelam PVC sheet instead of plain PVC sheets for top rails, lock rails and bottom rails on either side and as gap insert for top rail and bottom rail Panelling of both side prelam PVC sheet instead of plain PVC sheets to be fitted in the M.S frame welded /sealed to the stiles & rails with suitable prelam PVC sheet instead of plain PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site as per specification and drawing

Supply and fixing 100 mm butt hinges extruded aluminium alloy with mild steel hinge pin anodized and fixed complete all as specified and directed

Supply and fixing aluminum anodised barrel tower bolt 150 mm long of extructed section complete all as specified and directed

Supply and fixing aluminum anodised handle cast type 125mm, anodised complete all as specified and directed

Material and labour for Brick work with flyash bricks, straight or curved on plan exc 6 m mean radius built in CM 1:4 complete all as specified and directed

Material and labour pre cast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in cover slab set in CM 1:4, complete all as specifed and directed.

Supply and fixing TMT bars 6 to 8mm dia cut cut to length bent to shape required including binding with mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and as directed

Material and labour for Providing PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregate as in coping , benching/haunching , slightly rounded or chamfred angle and throating etc all as directed .

Material and labour 150mm dia Salt glazed stoneware drain pipe laid in trenches and jointed as specified

Material and labour for concrete bed to drain pipes including packing under and haunching against the sides of pipes after the air laid and tested in Cement Concrete 1:3:6 type C-2 for bore of pipes 150mm dia complete all as specified and directed

Cutting into existing manholes or septic tank for connecting new drains, making good to pipe and rendering, curring out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished for 100mm dia complete all as directed

Material and labour for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

Supply and fixing steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed

Supply and fixing 1.25mm steel rolling shutters, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or but gear operated type with bevel gear box and crank handle complete all as specified and directed

Supply and fixing plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified and directed

Supply and fixing roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc and jack rafter, purlin of Fe 410 W (Gde-E-250) quality A where connected to common rafter and connection plates guides, complete all as specified

Supply and fixing Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed

Supply and fixing Pre-painted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick of any colour having tensile strength of 550Mpsa as in roof covering/ cladding to wall, fixed with self-tapping screws as specified complete all as specified and directed

Material and labour for 11 to 15mm dia mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other or screwed both ends each screwed and to be bolted with washers and one hexagonal or square nit exc 50mm but n.exc. 100 mm long and dia of shank 10 to 16mm complete all as specified and directed

Material and labour for 18 to 20mm thick machine cut kota stone in flooring laid over and including 15mm thick screed in cement mortar (1:6) laid and jointed with grey cement slurry mixed with pigment to match the colour of stone slab including rubbing and polishing complete all as specified and directed

Material and labour for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment , laid over and including 25 mm thick sand cushion vibrated with mechanical vibrator complete all as specified and directed

Material and labour for spreading and levelling in layers n.exc. 25cm thick including well ramming and watering as required, complete all as specified and directed

Demolition of cement concrete in ground floor and paving not exceeding 15cm thickness (below or above ground) complete all as specified and directed

Material and labour for point wiring for light/fan point with 1.5 Sqmm (nominal area) FRLS PVC insulated unsheathed multi stranded copper conductor of size 1.5 Sqmm cable drawn in and including concealed rigid PVC conduit medium grade not less than 20mm dia with accessories including cutting chases for laying of conduit /fixing of boxes in walls/floor etc including making good to disturbed surfaces as per adjoining specification and terminated in and incl sunken pressed steel boxes duly painted with anti corrosive paint over a coat of red oxide primer with plastic laminated bakelite sheet top cover 3mm thick make hylum or equivalent fixed with nickel polished screws with cup washers etc including FRLS PVC insulated unsheathed multi stranded copper conductor 1.5 Sqmm single core as earth continuity conductor (green colour) connected with earth dolly with thimble complete all as specified and as directed by Engr-in-Charge.

All as per srl item No. 102.00 here-in-before but for one socket outlet 5 Amps on independent board complete all as specified.

All as per srl item No. 102.00 here-in-before but for one socket outlet 5 Amps on the same board complete all as specified.

All as per srl item No. 102.00 here-in-before but with 2.5 Sqmm (nominal area) FRLS PVC insulated unsheathed multistranded copper conductor cable for one 3 Pin 15 Amp socket on independent board including one 2.5 Sqmm copper conductor multi stranded green colour PVC insulated unsheathed FRLS cable 1100 volts grade as earth wire connected to common earth and earth dolly with all accessories complete all as specified and directed by Engineer-in-Charge.

All as per srl item No. 102.00 here-in-before but 3 pin 16 Amp socket outlet with 2.5 Sqmm PVC insulated unsheathed multi thread FRLS copper cable and 2.5 Sqmm PVC insulated FRLS copper cable for continuous earth continuity conductor complete all as specified and directed by Engineer-in-Charge.

Supply and fixing switch piano flush type, 5 Amps, single pole, one way complete all as specified.

Supply and fixing switch modular type, 5 Amps, single pole, one way complete all as specified.

Supply and fixing switch modular type, 15 Amps, single pole, one way complete all as specified.

Supply and fixing socket out let 6 Amp, 5 pin, 2-in-1 flush type complete all as specified.

Supply and fixing socket out let 5 Amp, 5 pin, modular type complete all as specified.

Supply and fixing of switch piano flush button single pole one way 15 Ampere complete all as specified and directed.

Supply and fixing socket outlet multipurpose 2 in 1, 5/6 pin, 5 & 15 Amps, flush type complete all as specified

Supply and fixing socket outlet multipurpose 3 in 1, 6 pin, 5 & 16 Amps, modular type complete all as specified

Supply and fixing ceiling rose surface type PVC/ polycarbonate 65mm x 50mm three terminal complete all as specified.

Material and labour in replacement for sheet metal DB for MCBs, SPN, 8 ways 240V, double door, single phase, with copper bus bar, neutral bar/ connectors/ earth link suitable copper thimbles, lugs etc complete all as specified. Make: EKINOX3 series of Legrand/Acti 9 metalic series of Schneider/Optipro of Indoasian/Osafe of HPL/Metallica of Havells or equivalent in ABB/ Siemens/ Hager

Supply and fixing MCB SP 6 to 32 Amps 240 V, 10 KA, B curve as per Osafe series of HPL/ Acti 9 series of Schneider/ Optipro of Indoasian or equivalent in Havells/ Legrend/ ABB/ Siemens/ Hager. complete all as specified and directed by Engineer-in-Charge

Supply and fixing MCB SPN 32 Amps 240 V, 10 KA, B curve as per Osafe series of HPL/ Acti 9 series of Schneider/ Optipro of Indoasian or equivalent in Havells/ Legrend/ ABB/ Siemens/ Hager. complete all as specified and directed by Engineer-in-Charge

Earthing complete galvanised steel earth plate electrode 60cmx60cmx6.0mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level with the top edge of electrode not less than 1.5 metres below normal ground level connected to galvanised earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron and including GI lead protection pipe of GI light grade 15mm dia upto 7.5 mtrs and watering pipe 20mm bore of GI medium grade with funnel and wire mesh, earth plate covered on all sides with min 150mm thick alternate layers of charcoal, salt all as shown in electrical plate No 3 of SSR Part-I 2009 connected to earthing point with PCC chamber and RCC cover in 1:2:4 complete with any type of earth work involved all as specified and directed and testing on completion. Note:- PCC Chamber shall be constructed at least 0.50 mtr away from on the earth pit electrode and pipe for watering shall be provided in slanting manner

Earthing complete GI earth plate electrode 60cmx60cmx6.0mm thick burried directly in ground vertically in pit not less than 2.25 metres below ground level with the top edge of earth plate at a depth not less than 1.5 metres below normal level covered on all sides with alternative layers of charcoal dust and common salt 15cm thick connected to galvainsed earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel earth wire protected by galvanized steel pipe light grade 15mm bore from top of the earth plate electrode upto test point and watering pipe 20mm bore of GI light grade with funnel and wire mesh, all as shown in electrical plate No 3 of SSR Part-I 2009 and connected to earthing point all as specified or indicated and testing on completion, including PCC earth pit (1:3:6) type C-2, RCC cover with MS frame including excavation and earth work complete all as specified and directed.

Supply and fixing in replacement Deco ultra slim linear LED lighting fixture with co-extruded polycarbonate body environmental friendly energy efficient ready to use pack 22 W LED batten, cool white, operating voltage 140-270V AC complete all as specified & directed by Engineer-in-Charge

Supply and fixing Deco ultra slim linear LED lighting fixture with co-extruded polycarbonate body environmental friendly energy efficient ready to use pack 9 W LED complete all as specified & directed by Engineer-in-Charge

Supply and fixing Deco ultra slim linear LED lighting fixture with co-extruded polycarbonate body environmental friendly energy efficient ready to use pack 18 W LED batten, minimum lumen efficacy 100 lumen/ watt, cool white, 240V, 50 Hz complete all as specified & directed by Engineer-in-Charge

Supply and fixing in repair 70 Watt energy saving LED Well Glass luminaire, environment friendly, long life corrosion resistant with high power light source, vertical surface mounting pressure die-cast aluminium housing complete all as specified and directed by Engineer-in-Charge

Supply, laying and testing cable XLPE Insulated, PVC sheathed, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sqmm 2 core complete laid in trenches passing through pipes/culverts/ under roads/ along wall all as specified and directed by Engineer-in-Charge

Supply, laying and testing cable XLPE Insulated, PVC sheathed, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6 sqmm 2 core complete laid in trenches passing through pipes/culverts/ under roads/ along wall all as specified and directed by Engineer-in-Charge

Supply, laying and testing cable XLPE Insulated, PVC sheathed, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm 3.5 core complete laid in trenches passing through pipes/culverts/ under roads/ along wall all as specified and directed by Engineer-in-Charge

Material and labour for GI tube light grade 40mm bore laid in trenches or fixed on wall/floor for protection of UG cable complete all as specified and directed.

Supply and laying old size sub class 'B' bricks laid flat in trenches over the cable with the length of brick perpendicular to the direction of cable length, compressive strength of brick shall not be less than 160 kg/cm² adjacent/abutting each other complete all as specified and directed by Engineer-in-Charge.

Material and labour Sand cushioning with 8cm thick layer of sand before laying of cable and 15cm thick after laying of cable in trenches complete all as specified and as directed Note : Punned thickness of 18cm will be measured and paid.

Supply and fixing exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, frame complete including cutting of hole in wall and making good to disturbed surface all as specified and directed

Material and labour for louvers made of power coated CRCA sheet square frame having aluminium flappers suitable for exhaust fan of 300mm size complete all as specified and directed

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed

Supply and fixing light grade GI bend pipe of length 0.6m and dia 25mm with necessary clamps and screws to completely fixed on wall complete all as specified and directed (for fixing of bldg. lights)

Supply and fixing 25mm dia steel tubing medium grade galvanised with all fittings and fixed laid in trenches complete all as specified and as directed

Material and labour for taking water connections from existing main water pipe line by cutting threading and fixing including fittings in position from GI/ DI pipe of dia upto 100mm complete including any type of earth work etc. all as specified and directed

Supply and fixing sheet metal enclosure DBs when MCBs to be used, SPN 4 ways 240 V, with copper bus bar, double door, complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cable/ wires complete all as specified

Supply and fixing triple pole and earth enclosure with a three pin and earth plug with socket complete with one triple pole MCB 32 Amps complete all as specified & directed by Engineer-in-Charge

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified & directed by Engineer-in-Charge

Supply and fixing switch socket combination, 3 pin ,16 Amp, flush type, universal complete all as specified and directed

Supply and fixing VTPN DB 4 way single door, suitable for MCCB 100 Amp, 4 pole having bus bar for neutral and earth, blanking strips complete all as specified and directed.

Supply and fixing in replacement MCCB 100 Amps, 415V, 16 KA, 4 pole, with adjustable thermal fix magnetic release, ICS=ICU=100% with spreader links and phase separator suitable for Srl Item No. 141.00 above complete all as specified and directed

Supply and fixing in replacement MCB TP 40 Amp, 415V, 10 KA, ‘B’ curve and all the necessary electrical connections complete all as specified and directed

Supply and fixing 240V, 10KA, ‘B’ curve MCB of single pole and current carrying capacity 10 Amp, in the MCB DB complete with connection testing and commissioning all as specified and directed

Material and labour for sub main wiring with two run of single core FRLS PVC insulated unsheathed multistranded copper conductor cable of 2.5 Sqmm drawn through in and including PVC rigid non metallic conduit (medium grade ISI marked) with all fittings including earth continuity FRLS copper conductor cable 2.5 Sqmm PVC insulated with green insulation with any type of civil work reqd including making good to disturbed surfaces to match existing surface complete all as specified. Note: Two run of 2.5 sqmm wire and one run of 2.5 sqmm wire as earth wire including PVC conduit shall be measured as one unit

Material and labour for sub main wiring with two run of single core FRLS PVC insulated unsheathed multistranded copper conductor cable of 4 Sqmm drawn through in and including PVC rigid non metallic conduit (medium grade ISI marked) with all fittings including earth continuity FRLS copper conductor cable 4 Sqmm PVC insulated with green insulation with any type of civil work reqd including making good to disturbed surfaces to match existing surface complete all as specified. Note: Two run of 4 sqmm wire and one run of 4 sqmm wire as earth wire including PVC conduit shall be measured as one unit

NIRMAL SINGH (BID ID -3056689)

M/S Vinod Kumar (BID ID -3058207)