IMPROVEMENT OF LT DISTRIBUTION AND CONVERSION OF LT OH LINES TO UG CABLES AND ALLIED WORKS IN TECH AREA AT AF STATION GWALIOR

Amount

Dismantling of ACSR or AAC conductors, complete all as specified and directed.

Dismantling of cross arms of MS channel or angle section etc, complete all as specified & directed.

Dismantling of insulators any type and any size, complete all as specified & directed.

Dismantling of stay assembly set including demolition of concrete and necessary excavation, complete all as specifed and directed.

Dismantling of GI Earth wire, complete all as specifed and directed.

Disconnecting, taking out and removing old existing underground LT cable of any description in any position, complete all as specifed and directed.

M&L for Earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, GI tubing 15mm bore medium grade protection pipe, GI watering pipe 20mm bore medium grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing , all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. The rate quoted shall also deemed to be included for :- 1. Earth lead & protection pipes length upto & including 7.50 metre. 2. Earth filling shall be done by vegetable soil. 3. Soil should be free from stone, boulders, aggregate, gravels etc. 4. MS sheet of size 300mmx300mmx3mm fixed with necessary nuts and bolts on angle iron frame of size 40x40x5 mm and length 60 cm all duly painted with black colour over a coat of red oxide primer and grouted in ground with PCC 1:3:6 using 20 mm graded stone aggregate of size 200mmx200mmx250mm including necessary earth work etc for mentioning earth test result.

Supply , laying , connecting and testing LT 1100 volt grade electric cable XLPE insulated, screened, PVC bedded, galvanised steel strip armoured (heavy duty) ISI marked with aluminium stranded conductor cross sectional area 16 Sqmm , 4 core laid in trenches / duct / pipe/pole including required lugs etc complete all as specified and directed. (Note:- Earthwork & excavation, GI pipe protection and sand cushion shall be measured & paid separetely under respective items)

Supply , laying , connecting and testing LT 1100 volt grade electric cable XLPE insulated, screened, PVC bedded, galvanised steel strip armoured (heavy duty) ISI marked with aluminium stranded conductor cross sectional area 35 Sqmm , 3.5 core laid in trenches / duct / pipe/pole including required lugs etc complete all as specified and directed. (Note:- Earthwork & excavation, GI pipe protection and sand cushion shall be measured & paid separetely under respective items)

Supply , laying , connecting and testing LT 1100 volt grade electric cable XLPE insulated, screened, PVC bedded, galvanised steel strip armoured (heavy duty) ISI marked with aluminium stranded conductor cross sectional area 50 Sqmm , 3.5 core laid in trenches / duct / pipe/pole including required lugs etc complete all as specified and directed. (Note:- Earthwork & excavation, GI pipe protection and sand cushion shall be measured & paid separetely under respective items)

Supply , laying , connecting and testing LT 1100 volt grade electric cable XLPE insulated, screened, PVC bedded, galvanised steel strip armoured (heavy duty) ISI marked with aluminium stranded conductor cross sectional area 70 Sqmm , 3.5 core laid in trenches / duct / pipe/pole including required lugs etc complete all as specified and directed. (Note:- Earthwork & excavation, GI pipe protection and sand cushion shall be measured & paid separetely under respective items)

Supply , laying , connecting and testing LT 1100 volt grade electric cable XLPE insulated, screened, PVC bedded, galvanised steel strip armoured (heavy duty) ISI marked with aluminium stranded conductor cross sectional area 95 Sqmm , 3.5 core laid in trenches / duct / pipe/pole including required lugs etc complete all as specified and directed. (Note:- Earthwork & excavation, GI pipe protection and sand cushion shall be measured & paid separetely under respective items)

Supply , laying , connecting and testing LT 1100 volt grade electric cable XLPE insulated, screened, PVC bedded, galvanised steel strip armoured (heavy duty) ISI marked with aluminium stranded conductor cross sectional area 150 Sqmm , 3.5 core laid in trenches / duct / pipe/pole including required lugs etc complete all as specified and directed. (Note:- Earthwork & excavation, GI pipe protection and sand cushion shall be measured & paid separetely under respective items)

Supply , laying , connecting and testing LT 1100 volt grade electric cable XLPE insulated, screened, PVC bedded, galvanised steel strip armoured (heavy duty) ISI marked with aluminium stranded conductor cross sectional area 185 Sqmm , 3.5 core laid in trenches / duct / pipe/pole including required lugs etc complete all as specified and directed. (Note:- Earthwork & excavation, GI pipe protection and sand cushion shall be measured & paid separetely under respective items)

Supply , laying , connecting and testing LT 1100 volt grade electric cable XLPE insulated, screened, PVC bedded, galvanised steel strip armoured (heavy duty) ISI marked with aluminium stranded conductor cross sectional area 240 Sqmm , 3.5 core laid in trenches / duct / pipe/pole including required lugs etc complete all as specified and directed. (Note:- Earthwork & excavation, GI pipe protection and sand cushion shall be measured & paid separetely under respective items)

Supply , laying , connecting and testing LT 1100 volt grade electric cable XLPE insulated, screened, PVC bedded, galvanised steel strip armoured (heavy duty) ISI marked with aluminium stranded conductor cross sectional area 300 Sqmm , 3.5 core laid in trenches / duct / pipe/pole including required lugs etc complete all as specified and directed. (Note:- Earthwork & excavation, GI pipe protection and sand cushion shall be measured & paid separetely under respective items)

Excavation in trenches in hard / dence soil, not exc 1.5 m in width and not exc 1.5 m in depth for laying of cable lines etc and getting out including forming bottom surface, complete all as specifed and directed. NOTE :- (i) Contractor shall take written approval of entire route for excavation before commencing excavation work. (ii) Proper care shall be taken for existing underground services, pipe line / cable during execution. Any damage to the services done during the excavation will be resorted (As per sound Engineering practice) within 24 hrs at his own cost by the Contractor. (iii) For any delay beyond 24 Hrs for whatsoever reason, Penalty of Rs 1000/- per day will be levied upon the contractor.

Supply and spreading clean, dry, fine river sand for UG electric cable in two layers (8 cm thick before laying the cable & 15 cm thick after laying cable ) total 23 cm thick including gently punning the sand up to 18 cm (total thickness) and consolidated around cable for protection of under ground cable complete all as specified and directed. ( Note:- Only punned thickness shall be measured for payment).

Supply & laying unreinforced precast concrete cable cover class LV, Type I flat of size 250mm x150 mm x 40 mm (ISI marked) complete all as specified & directed.

Boring horizontal holes of 150 mm dia in required length across the road, pavement, hard standing by trenchless technology (without disturbing top surface) using ultra sounding technique by deploying required machinery in & including insertion of HDPE pipe of 150 mm bore suitable for 0.4 mpa working pressure in the board hole all as specified and directed.

Supply, Install, Testing and Commissioning, factory made, CPRI type tested, totally enclosed, IP 54 dust, weather and vermin proof, CRCA sheet out door LT Panel for 415V, 3 phase 4 wire , 50 Hz AC system with TPN tinned copper bus bar of rating 1.5 times that of controlling MCCB supported on F class DMC/FRP insulator with short circuit withstand capacity 21 MVA for 1 second, neutral bus bar of capacity of that of phase bus bar , general construction confirming to IS-8623/93, having bottom base channel of MS section not less than 75mm x 75 mm x 5 mm , entire panel having common aluminium earth bar of size 25mm x 5mm at the rear with 2 Nos earth stud, solid connection from main bus bar to switchgears with required size (minimum 1.5 Sqmm) PVC insulated copper conductor cable , cable alleys, cable gland plates in two half inculding LED indicating lamp for all phases and mounted on suitable PCC foundation for the complete panel base with following detailed specification, control and accessories complete all as specified below and as directed:-

OUTER SHELL :- The outer shell shall be made of min 3 mm thick CRCA sheet supported on MS angle section 75mm x 75 mm x 5 mm frame with openable front & back with concelaed hinges , single door system, lockable/ openable by by keys from both sides, having flush pattern fancy locks, louvers & air vent with gasket for natural flow of air. The bottom of the outer shell contains a detachable plate with hinges provision for entry of armoured cable with adequite size glands. Provision of earthing studs at bottom and threaded lifting lugs of suitable size at top to lift the feeder pillar box safely shall be made. Computer cut self adhesive vinyl danger notice plate having conventional symbol of bone and skull shall be provided.

INNER SHELL :- Inner shell made of 2.0 mm thick CRCA sheet compartmentalized to accomodate each control gear, front openable, single door system lockable/openable with "U' type gasket to make the inner shell completely vermin proof having chromium plated locks (2 Nos in each compartment.) All control wiring shall be with not less than 1.5 Sqmm multistranded copper conductor and shall be properly bunched. tied, ferruled for proper identification and crimped with adequite size of lugs. The cubical shall have a bottom channel of size 75x75x5 mm duly painted with zinc based primer. A detachable predrilled gland plate of thickness 3.15 mm should be used at the bottom, . An inspection lamp with 11 Watt CFL shall be fitted on top side of inner shell. (A) Incoming :- (i) MCCB 4P, 63A, fixed thermal and magnetic setting, Ics=100%Icu, 10 KA -01 No. (B) Out going :- (a) MCCB 4P, 32 A, fixed thermal and magnetic setting, Ics=100%Icu 10 KA - 02 Nos (b) Power Contactor 70 Amps - 1 Nos. (c) Digital Type GIC Astro Timer Switch 230 Volts -1Nos (d) The following items are provided in each compartment :- (i) Digital Voltmeter - 01 No (ii) Digital Ammeter - 01 No. (iii) Set of three Indication LED (RYB) Lamp.

Supply, Install, Testing and Commissioning, factory made, CPRI type tested, totally enclosed, IP 54 dust, weather and vermin proof, CRCA sheet out door LT Panel for 415V, 3 phase 4 wire , 50 Hz AC system with TPN tinned copper bus bar of rating 1.5 times that of controlling MCCB supported on F class DMC/FRP insulator with short circuit withstand capacity 21 MVA for 1 second, neutral bus bar of capacity of that of phase bus bar , general construction confirming to IS-8623/93, having bottom base channel of MS section not less than 75mm x 75 mm x 5 mm , entire panel having common aluminium earth bar of size 25mm x 5mm at the rear with 2 Nos earth stud, solid connection from main bus bar to switchgears with required size (minimum 1.5 Sqmm) PVC insulated copper conductor cable , cable alleys, cable gland plates in two half inculding LED indicating lamp for all phases and mounted on suitable PCC foundation for the complete panel base with following detailed specification, control and accessories complete all as specified below and as directed :-

OUTER SHELL :- The outer shell shall be made of min 3 mm thick CRCA sheet supported on MS angle section 75mm x 75 mm x 5 mm frame with openable front & back with concelaed hinges , single door system, lockable/ openable by by keys from both sides, having flush pattern fancy locks, louvers & air vent with gasket for natural flow of air. The bottom of the outer shell contains a detachable plate with hinges provision for entry of armoured cable with adequite size glands. Provision of earthing studs at bottom and threaded lifting lugs of suitable size at top to lift the feeder pillar box safely shall be made. Computer cut self adhesive vinyl danger notice plate having conventional symbol of bone and skull shall be provided.

INNER SHELL :- Inner shell made of 2.0 mm thick CRCA sheet compartmentalized to accomodate each control gear, front openable, single door system lockable/openable with "U' type gasket to make the inner shell completely vermin proof having chromium plated locks (2 Nos in each compartment). All control wiring shall be with not less than 1.5 Sqmm multistranded copper conductor and shall be properly bunched. tied, ferruled for proper identification and crimped with adequite size of lugs. The cubical shall have a bottom channel of size 75x75x5 mm duly painted with zinc based primer. A detachable predrilled gland plate of thickness 3.15 mm should be used at the bottom, . An inspection lamp with 11 Watt CFL shall be fitted on top side of inner shell. (A) Incoming :- (i) MCCB 4P, 100A, fixed thermal and magnetic setting, Ics=100%Icu, 16 KA -01 No. (B) Out going :- (a) MCCB 4P, 63 A, fixed thermal and magnetic setting, Ics=100%Icu,16 KA - 01 No. (b) Power Contactor 125 Amps - 1 Nos. (c) Digital Type GIC Astro Timer Switch 230 Volts -1Nos (d) The following items are provided in each compartment :- (i) Digital Voltmeter - 01 No (ii) Digital Ammeter - 01 No. (iii) Set of three Indication LED (RYB) Lamp.

Supply, Install, Testing and Commissioning, factory made, CPRI type tested, totally enclosed, IP 54 dust, weather and vermin proof, CRCA sheet out door LT Panel for 415V, 3 phase 4 wire , 50 Hz AC system with TPN tinned copper bus bar of rating 1.5 times that of controlling MCCB supported on F class DMC/FRP insulator with short circuit withstand capacity 21 MVA for 1 second, neutral bus bar of capacity of that of phase bus bar , general construction confirming to IS-8623/93, having bottom base channel of MS section not less than 75mm x 75 mm x 5 mm , entire panel having common aluminium earth bar of size 25mm x 5mm at the rear with 2 Nos earth stud, solid connection from main bus bar to switchgears with required size (minimum 1.5 Sqmm) PVC insulated copper conductor cable , cable alleys, cable gland plates in two half inculding LED indicating lamp for all phases and mounted on suitable PCC foundation for the complete panel base with following detailed specification, control and accessories complete all as specified below and as directed :-

OUTER SHELL :- The outer shell shall be made of min 3 mm thick CRCA sheet supported on MS angle section 75mm x 75 mm x 5 mm frame with openable front & back with concelaed hinges , single door system, lockable/ openable by by keys from both sides, having flush pattern fancy locks, louvers & air vent with gasket for natural flow of air. The bottom of the outer shell contains a detachable plate with hinges provision for entry of armoured cable with adequite size glands. Provision of earthing studs at bottom and threaded lifting lugs of suitable size at top to lift the feeder pillar box safely shall be made. Computer cut self adhesive vinyl danger notice plate having conventional symbol of bone and skull shall be provided.

INNER SHELL :- Inner shell made of 2.0 mm thick CRCA sheet compartmentalized to accomodate each control gear, front openable, single door system lockable/openable with "U' type gasket to make the inner shell completely vermin proof having chromium plated locks (2 Nos in each compartment) All control wiring shall be with not less than 1.5 Sqmm multistranded copper conductor and shall be properly bunched. tied, ferruled for proper identification and crimped with adequite size of lugs. The cubical shall have a bottom channel of size 75x75x5 mm duly painted with zinc based primer. A detachable predrilled gland plate of thickness 3.15 mm should be used at the bottom, . An inspection lamp with 11 Watt CFL shall be fitted on top side of inner shell. (A) Incoming :- (i) MCCB 4P, 63A, fixed thermal and magnetic setting, Ics=100%Icu, 10 KA -01 No. (B) Out going :- (a) MCCB 4P, 32 A, fixed thermal and magnetic setting, Ics=100%Icu,10 KA 01 No. (b) Power Contactor 70 Amps - 1 Nos. (c) Digital Type GIC Astro Timer Switch 230 Volts -1Nos (d) The following items are provided in each compartment :- (i) Digital Voltmeter - 01 No (ii) Digital Ammeter - 01 No. (iii) Set of three Indication LED (RYB) Lamp.

Supply, Install, Testing and Commissioning, factory made, CPRI type tested, totally enclosed, IP 54 dust, weather and vermin proof, CRCA sheet out door LT Panel for 415V, 3 phase 4 wire , 50 Hz AC system with TPN tinned copper bus bar of rating 1.5 times that of controlling MCCB supported on F class DMC/FRP insulator with short circuit withstand capacity 21 MVA for 1 second, neutral bus bar of capacity of that of phase bus bar , general construction confirming to IS-8623/93, having bottom base channel of MS section not less than 75mm x 75 mm x 5 mm , entire panel having common aluminium earth bar of size 25mm x 5mm at the rear with 2 Nos earth stud, solid connection from main bus bar to switchgears with required size (minimum 1.5 Sqmm) PVC insulated copper conductor cable , cable alleys, cable gland plates in two half inculding LED indicating lamp for all phases and mounted on suitable PCC foundation for the complete panel base with following detailed specification, control and accessories complete all as specified below and as directed:-

OUTER SHELL :- The outer shell shall be made of min 3 mm thick CRCA sheet supported on MS angle section 75mm x 75 mm x 5 mm frame with openable front & back with concelaed hinges , single door system, lockable/ openable by by keys from both sides, having flush pattern fancy locks, louvers & air vent with gasket for natural flow of air. The bottom of the outer shell contains a detachable plate with hinges provision for entry of armoured cable with adequite size glands. Provision of earthing studs at bottom and threaded lifting lugs of suitable size at top to lift the feeder pillar box safely shall be made. Computer cut self adhesive vinyl danger notice plate having conventional symbol of bone and skull shall be provided.

INNER SHELL :- Inner shell made of 2.0 mm thick CRCA sheet compartmentalized to accomodate each control gear, front openable, single door system lockable/openable with "U' type gasket to make the inner shell completely vermin proof having chromium plated locks (2 Nos in each compartment) All control wiring shall be with not less than 1.5 Sqmm multistranded copper conductor and shall be properly bunched. tied, ferruled for proper identification and crimped with adequite size of lugs. The cubical shall have a bottom channel of size 75x75x5 mm duly painted with zinc based primer. A detachable predrilled gland plate of thickness 3.15 mm should be used at the bottom, . An inspection lamp with 11 Watt CFL shall be fitted on top side of inner shell. (A) Incoming :- (i) MCCB 4P, 160A, fixed thermal and magnetic setting, Ics=100%Icu, 25 KA -01 No. (B) Out going :- (a) MCCB 4P, 100 A, fixed thermal and magnetic setting, Ics=100%Icu,16 KA 01 No. (b) MCCB 4P, 63 A, fixed thermal and magnetic setting, Ics=100%Icu,10 KA 02 No. (b) Power Contactor 160 Amps - 1 Nos. (c) Digital Type GIC Astro Timer Switch 230 Volts -1Nos (d) The following items are provided in each compartment :- (i) Digital Voltmeter - 01 No (ii) Digital Ammeter - 01 No. (iii) Set of three Indication LED (RYB) Lamp.

Supply, Install, Testing and Commissioning, factory made, CPRI type tested, totally enclosed, IP 54 dust, weather and vermin proof, CRCA sheet out door LT Panel for 415V, 3 phase 4 wire , 50 Hz AC system with TPN tinned copper bus bar of rating 1.5 times that of controlling MCCB supported on F class DMC/FRP insulator with short circuit withstand capacity 21 MVA for 1 second, neutral bus bar of capacity of that of phase bus bar , general construction confirming to IS-8623/93, having bottom base channel of MS section not less than 75mm x 75 mm x 5 mm , entire panel having common aluminium earth bar of size 25mm x 5mm at the rear with 2 Nos earth stud, solid connection from main bus bar to switchgears with required size (minimum 1.5 Sqmm) PVC insulated copper conductor cable , cable alleys, cable gland plates in two half inculding LED indicating lamp for all phases and mounted on suitable PCC foundation for the complete panel base with following detailed specification, control and accessories complete all as specified below and as directed :-

OUTER SHELL :- The outer shell shall be made of min 3 mm thick CRCA sheet supported on MS angle section 75mm x 75 mm x 5 mm frame with openable front & back with concelaed hinges , single door system, lockable/ openable by by keys from both sides, having flush pattern fancy locks, louvers & air vent with gasket for natural flow of air. The bottom of the outer shell contains a detachable plate with hinges provision for entry of armoured cable with adequite size glands. Provision of earthing studs at bottom and threaded lifting lugs of suitable size at top to lift the feeder pillar box safely shall be made. Computer cut self adhesive vinyl danger notice plate having conventional symbol of bone and skull shall be provided.

INNER SHELL :- Inner shell made of 2.0 mm thick CRCA sheet compartmentalized to accomodate each control gear, front openable, single door system lockable/openable with "U' type gasket to make the inner shell completely vermin proof having chromium plated locks (2 Nos in each compartment) All control wiring shall be with not less than 1.5 Sqmm multistranded copper conductor and shall be properly bunched. tied, ferruled for proper identification and crimped with adequite size of lugs. The cubical shall have a bottom channel of size 75x75x5 mm duly painted with zinc based primer. A detachable predrilled gland plate of thickness 3.15 mm should be used at the bottom, . An inspection lamp with 11 Watt CFL shall be fitted on top side of inner shell. (A) Incoming :- (i) MCCB 4P, 800A, fixed thermal and magnetic setting, Ics=100%Icu, 50 KA -01 No. (B) Out going :- (a) MCCB 4P, 630 A, fixed thermal and magnetic setting, Ics=100%Icu,36 KA - 01 No. (b) MCCB 4P, 63 A, fixed thermal and magnetic setting, Ics=100%Icu,16 KA - 01 No. (b) Power Contactor 70 Amps - 1 Nos. (c) Digital Type GIC Astro Timer Switch 230 Volts -1Nos (d) The following items are provided in each compartment :- (i) Digital Voltmeter - 01 No (ii) Digital Ammeter - 01 No. (iii) Set of three Indication LED (RYB) Lamp.

Supply, Install, Testing and Commissioning, factory made, CPRI type tested, totally enclosed, IP 54 dust, weather and vermin proof, CRCA sheet out door LT Panel for 415V, 3 phase 4 wire , 50 Hz AC system with TPN tinned copper bus bar of rating 1.5 times that of controlling MCCB supported on F class DMC/FRP insulator with short circuit withstand capacity 21 MVA for 1 second, neutral bus bar of capacity of that of phase bus bar , general construction confirming to IS-8623/93, having bottom base channel of MS section not less than 75mm x 75 mm x 5 mm , entire panel having common aluminium earth bar of size 25mm x 5mm at the rear with 2 Nos earth stud, solid connection from main bus bar to switchgears with required size (minimum 1.5 Sqmm) PVC insulated copper conductor cable , cable alleys, cable gland plates in two half inculding LED indicating lamp for all phases and mounted on suitable PCC foundation for the complete panel base with following detailed specification, control and accessories complete all as speciefied below and as directed:-

OUTER SHELL :- The outer shell shall be made of min 3 mm thick CRCA sheet supported on MS angle section 75mm x 75 mm x 5 mm frame with openable front & back with concelaed hinges , single door system, lockable/ openable by by keys from both sides, having flush pattern fancy locks, louvers & air vent with gasket for natural flow of air. The bottom of the outer shell contains a detachable plate with hinges provision for entry of armoured cable with adequite size glands. Provision of earthing studs at bottom and threaded lifting lugs of suitable size at top to lift the feeder pillar box safely shall be made. Computer cut self adhesive vinyl danger notice plate having conventional symbol of bone and skull shall be provided.

INNER SHELL :- Inner shell made of 2.0 mm thick CRCA sheet compartmentalized to accomodate each control gear, front openable, single door system lockable/openable with "U' type gasket to make the inner shell completely vermin proof having chromium plated locks (2 Nos in each compartment) All control wiring shall be with not less than 1.5 Sqmm multistranded copper conductor and shall be properly bunched. tied, ferruled for proper identification and crimped with adequite size of lugs. The cubical shall have a bottom channel of size 75x75x5 mm duly painted with zinc based primer. A detachable predrilled gland plate of thickness 3.15 mm should be used at the bottom, . An inspection lamp with 11 Watt CFL shall be fitted on top side of inner shell. (A) Incoming :- (i) MCCB 4P, 63A, fixed thermal and magnetic setting, Ics=100%Icu, 10 KA -01 No. (B) Out going :- (a) MCCB 4P, 32A, fixed thermal and magnetic setting, Ics=100%Icu,10 KA 01 No. (b) Power Contactor 70 Amps - 1 Nos. (c) Digital Type GIC Astro Timer Switch 230 Volts -1Nos (d) The following items are provided in each compartment :- (i) Digital Voltmeter - 01 No (ii) Digital Ammeter - 01 No. (iii) Set of three Indication LED (RYB) Lamp.

Design, fabricate, Supply, install, test and commissioning of factory made, powder coated, dust and vermin proof, outdoor cubical type bus bar box, suitable for 3 phase, 4 wire, 415 volts AC supply, fabricated with 3mm thick CRCA sheet of suitable size to accomodate 200 Amps color coded with heat shrink sleeve, copper busbar 40mmx10mm - 04 Nos , 400mm long fixed on F Class SMC/ DMC insulators , using 40mmx40mmx5mm angle iron frame with with shutter and locking arrangement, angle iron pedestal of size 50mmX50mmX5mm, 60 cm above the ground level & 30cm embedded in concrete block, cast in situ with PCC 1:2:4 type B1 using 20 mm aggregate of size 300mmX300mmX300 mm (above ground level) and 450mmx450 mmx450mm (below ground level) all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron strip of size 25 x 4 mm as earth lead by means of bolts, nuts and washers of GI up to test point, GI tubing 40 mm bore light grade protection pipe, GI watering pipe 20mm bore medium grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing , all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre. 2. Earth filling shall be done by vegetable soil. 3. Soil should be free from stone, boulders, aggregate, gravels etc. 4. MS sheet of size 300mmx300mmx3mm fixed with necessary nuts and bolts on angle iron frame of size 40x40x5 mm and length 60 cm all duly painted with black colour and grouted in ground with PCC 1:3:6 using 20 mm graded stone aggregate of size 200mmx200mmx250mm including necessary earth work for mentioning earth test result.

Supply, Install, Testing & commissioning of Servo Voltage stabilizer conforming to IS 9814, Part I: 1994, three phase, naturally oil cooled, out door operation & designed for automatic operation on unbalanced voltage and unbalanced load, input vairation between 300 V-480 V (3 phase) with 3 phase output voltage stabilized at 415V +/-1 % (adjustable) , speed of correction 10V/sec min, efficiency not less than 95%, response time less than 10ms, suitable for ambient working temperature 0-50 degree celsius, relative humidity 90%, of capacity 50 KVA complete all as directed and specified along with the following features. (i) Regulator for sensing circuit to maintain constant output voltage even on DG. (ii) Min metering should be digital VIF meter for input and output voltage, out put current and frequency. (iii) Protection : High/low voltage cut-off, single phasing cut off, single phase sequence change cut off, over temperature cut off, spike/surge protection. (iv) Surge protection device 8/20 micro sec as per IEC-61000-4-4/61000-4-5. (v) Stabilizer by pass switch, Out put voltage protection, Adujustable output under and over volt, Auto - manual switch

Supply, Install, Testing & commissioning of Servo Voltage stabilizer conforming to IS 9814, Part I: 1994, three phase, naturally oil cooled, out door operation & designed for automatic operation on unbalanced voltage and unbalanced load, input vairation between 300 V-480V (3 phase) with 3 phase output voltage stabilized at 415V +/-1 % (adjustable) , speed of correction 10V/sec min, efficiency not less than 95%, response time less than 10ms, suitable for ambient working temperature 0-50 degree celsius, relative humidity 90%, of capacity 100 KVA complete all as directed and specified along with the following features. (i) Regulator for sensing circuit to maintain constant output voltage even on DG. (ii) Min metering should be digital VIF meter for input and output voltage, out put current and frequency. (iii) Protection : High/low voltage cut-off, single phasing cut off, single phase sequence change cut off, over temperature cut off, spike/surge protection. (iv) Surge protection device 8/20 micro sec as per IEC-61000-4-4/61000-4-5. (v) Stabilizer by pass switch, Out put voltage protection, Adujustable output under and over volt, Auto - manual switch

Supply, Install, Testing & commissioning of Servo Voltage stabilizer conforming to IS 9814, Part I: 1994, three phase, naturally oil cooled, out door operation & designed for automatic operation on unbalanced voltage and unbalanced load, input vairation between 300 V-480V (3 phase) with 3 phase output voltage stabilized at 415V +/-1 % (adjustable) , speed of correction 10V/sec min, efficiency not less than 95%, response time less than 10ms, suitable for ambient working temperature 0-50 degree celsius, relative humidity 90%, of capacity 200 KVA complete all as directed alongwith the following features :- (i) Regulator for sensing circuit to maintain constant output voltage even on DG. (ii) Min metering should be digital VIF meter for input and output voltage, out put current and frequency. (iii) Protection : High/low voltage cut-off, single phasing cut off, single phase sequence change cut off, over temperature cut off, spike/surge protection. (iv) Surge protection device 8/20 micro sec as per IEC-61000-4-4/61000-4-5. (v) Stabilizer by pass switch, Out put voltage protection, Adujustable output under and over volt, Auto - manual switch

Supply, Install, Testing & commissioning of Servo Voltage stabilizer conforming to IS 9814, Part I: 1994, three phase, naturally oil cooled, out door operation & designed for automatic operation on unbalanced voltage and unbalanced load, input vairation between 300 V-480V (3 phase) with 3 phase output voltage stabilized at 415V +/-1 % (adjustable) , speed of correction 10V/sec min, efficiency not less than 95%, response time less than 10ms, suitable for ambient working temperature 0-50 degree celsius, relative humidity 90%, of capacity 300 KVA complete all as directed and specified along with the following features. (i) Regulator for sensing circuit to maintain constant output voltage even on DG. (ii) Min metering should be digital VIF meter for input and output voltage, out put current and frequency. (iii) Protection : High/low voltage cut-off, single phasing cut off, single phase sequence change cut off, over temperature cut off, spike/surge protection. (iv) Surge protection device 8/20 micro sec as per IEC-61000-4-4/61000-4-5. (v) Stabilizer by pass switch, Out put voltage protection, Adujustable output under and over volt, Auto - manual switch

Supply, Install, Testing & commissioning of Servo Voltage stabilizer conforming to IS 9814, Part I: 1994, three phase, naturally oil cooled, out door operation & designed for automatic operation on unbalanced voltage and unbalanced load, input vairation between 380 V-480V (3 phase) with 3 phase output voltage stabilized at 415V +/-1 % (adjustable) , speed of correction 10V/sec min, efficiency not less than 95%, response time less than 10ms, suitable for ambient working temperature 0-50 degree celsius, relative humidity 90%, of capacity 400 KVA complete all as directed and specified along with the following features :- (i) Regulator for sensing circuit to maintain constant output voltage even on DG. (ii) Min metering should be digital VIF meter for input and output voltage, out put current and frequency. (iii) Protection : high/low voltage cut-off, single phasing cut off, single phase sequence change cut off, over temperature cut off, spike/surge protection. (iv) Surge protection device 8/20 micro sec as per IEC-61000-4-4/61000-4-5. (v) Stabilizer by pass switch, Out put voltage protection, Adujustable output under and over volt, Auto - manual switch

Supplying Installation, Testing & commissioning of floor mounted or free standing (grouted in PCC 1:2:4 type B1), duly labelled with vinyl stickers, modular construction, 6 stage, 415 +/- 10%, 50 +/- 5% HZ, 50 KVAR (in stages) Automatic Power Factor Correction panel to be operated in Auto and Manual mode, fabricated in minimum 16 SWG CRCA sheet , supported with suitable size base channel not less than 75x75x5 mm, painted in Siemens Gray shade RAL 703, compartmentalised, dust and vermin proof, IP 42 protection, doors and covers with non ageing gasket, doors with concealed hinges with handle and locking facility, cable glands, cable bottom entry for incoming and outgoing cable, danger plate, thermostatically controlled strip heater with provn of double earthing terminals, lifting studs, louvers for proper ventilation with 02 nos Suitable size & capacity but not less than 6 Inches metal/PVC body exhaust fan, with microprocessor based power factor controller , neatly bunched control wiring ( with 1 sq mm ) and power wiring with flexible PVC copper cable, adequately supported and routed through cable duct with identification tag seperate cable spacing betwen phase & neutral, alarm during the failure of power supply or in any one phase and comprising of following :- (i) APFC Relay - 3 phase, 6 stage solid state automatic power factor correction relay, directly connected with busbar through suitable size copper conductor , measuring reactive power through CT secondary of rating 5A for operating capacitor bank in steps 1 X 20 KVAR, 2 X 10 KVAR, 1 X 5 KVAR & 2 X 2.5 KVAR to maintain target PF > 0.98, microprocessor (intelligent) based control circuit.

(ii) Switchgear :- Incoming : 100 AMP MCCB, 25 KA, Ics= 100 % Icu with adjustable Over Load and Short circuit protection -01 No Outgoing :- (a) 40 Amp, 10 KA TPN MCB -01 Nos. (b) 16 Amp, 10 KA TPN MCB-03 Nos. (b) 10 Amp, 10 KA TPN MCB-02 Nos. (iii) Contactors :- 3 phase Capacitor duty contactor confirming to IEC 60947 capable to withstand 200 times of rated current with ON/OFF push button, with indication for ON position (a) 40 A-1 No (b) 16 A -3 No (b) 10 A -2 No Capacitor :- Air cooled , 440 Volt, delta connected MPP type heay duty , confirming to IS 13340-1993, max transient in rush current 200 In. with discharge resitors , over pressure disconnector , suitable for Overloading as 115% for Over Current and 110% for Over Voltage, Watt Loss <0.5w/kVAr. of capacities (a) 20 KVAR - 01 No, (b) 10 KVAR - 02 No, (c) 5 KVAR -01 No (d) 2.5 KVAR -02 No. (iv) Busbar:- 1 set of 200 Amps uniformly rated, 415 V, 3P+1N electrolytic grade copper bus bar of adequate length and cross section with heat shrink colour coded sleeve, supported on F class DMC/FRP insulators

Supplying Installation, Testing & commissioning of floor mounted or free standing (grouted in PCC 1:2:4 type B1), duly labelled with vinyl stickers, modular construction, 6 stage, 415 +/- 10%, 50 +/- 5% HZ, 75 KVAR (in stages) Automatic Power Factor Correction panel , to be operated in Auto and Manual mode, fabricated in minimum 16 SWG CRCA sheet , supported with suitable size base channel not less than 75x75x5 mm, painted in Siemens Gray shade RAL 703, compartmentalised, dust and vermin proof, IP 42 protection, doors and covers with non ageing gasket, doors with concealed hinges with handle and locking facility, cable glands, cable bottom entry for incoming and outgoing cable, danger plate, thermostatically controlled strip heater with provn of double earthing terminals, lifting studs, louvers for proper ventilation with 02 nos Suitable size & capacity but not less than 6 Inches metal/PVC body exhaust fan, with microprocessor based power factor controller ,, neatly bunched control wiring ( with 1 sq mm ) and power wiring with flexible PVC copper cable, adequately supported and routed through cable duct with identification tag seperate cable spacing betwen phase & neutral, alarm during the failure of power supply or in any one phase and comprising of following :- (i) APFC Relay - 3 phase, 6 stage solid state automatic power factor correction relay, directly connected with busbar through suitable size copper conductor , measuring reactive power through CT secondary of rating 5A for operating capacitor bank in steps 1 X 25 KVAR, 1 X 20 KVAR, 2 X 10 KVAR & 2 X 5 KVAR to maintain target PF > 0.98, microprocessor (intelligent) based control circuit.

(ii) Switchgear :- Incoming : 125 AMP MCCB, 25 KA, Ics= 100 % Icu with adjustable Over Load and Short circuit protection -01 No Outgoing :- (a) 63 Amp, 16 KA TPN MCB -01 Nos. (b) 40 Amp, 10 KA TPN MCB-01 Nos. (c) 16 Amp, 10 KA TPN MCB-04 Nos. (iii) Contactors :- 3 phase Capacitor duty contactor confirming to IEC 60947 capable to withstand 200 times of rated current with ON/OFF push button, with indication for ON position (a) 63 A-1 No (b) 40 A -1 No (b) 16 A -4 No Capacitor :- Air cooled , 440 Volt, delta connected MPP type heay duty , confirming to IS 13340-1993, max transient inrush current 200 In. with discharge resitors , over pressure disconnector , suitable for Overloading as 115% for Over Current and 110% for Over Voltage, Watt Loss <0.5w/kVAr. of capacities (a) 25 KVAR - 01 No, (b) 20 KVAR - 01 No, (c) 10 KVAR -02 No (d) 5 KVAR -02 No. (iv) Busbar:- 1 set of 200 Amps uniformly rated, 415 V, 3P+1N electrolytic grade copper bus bar of adequate length and cross section with heat shrink colour coded sleeve, supported on F class DMC/FRP insulators

Supplying Installation, Testing & commissioning of floor mounted or free standing (grouted in PCC 1:2:4 type B1), duly labelled with vinyl stickers, modular construction, 6 stage, 415 +/- 10%, 50 +/- 5% HZ, 125 KVAR (in stages) Automatic Power Factor Correction panel , to be operated in Auto and Manual mode, fabricated in minimum 16 SWG CRCA sheet , supported with suitable size base channel not less than 75x75x5 mm, painted in Siemens Gray shade RAL 703, compartmentalised, dust and vermin proof, IP 42 protection, doors and covers with non ageing gasket, doors with concealed hinges with handle and locking facility, cable glands, cable bottom entry for incoming and outgoing cable, danger plate, thermostatically controlled strip heater with provn of double earthing terminals, lifting studs, louvers for proper ventilation with 02 nos Suitable size & capacity but not less than 6 Inches metal/PVC body exhaust fan, with microprocessor based power factor controller neatly bunched control wiring ( with 1 sq mm ) and power wiring with flexible PVC copper cable, adequately supported and routed through cable duct with identification tag seperate cable spacing betwen phase & neutral, alarm during the failure of power supply or in any one phase and comprising of following :- (i) APFC Relay - 3 phase, 6 stage solid state automatic power factor correction relay, directly connected with busbar through suitable size copper conductor , measuring reactive power through CT secondary of rating 5A for operating capacitor bank in steps 1 X 50 KVAR, 2 X 25 KVAR, 2 X 10 KVAR & 1 X 5 KVAR to maintain target PF > 0.98, microprocessor (intelligent) based control circuit.

(ii) Switchgear :- Incoming : 200 AMP MCCB, 25 KA, Ics= 100 % Icu with adjustable Over Load and Short circuit protection -01 No Outgoing :- (a) 100 Amp, 25 KA TPN MCCB -01 Nos. (b) 63 Amp, 16 KA TPN MCCB-02 Nos. (b) 16 Amp, 10 KA TPN MCB-03 Nos. (iii) Contactors :- 3 phase Capacitor duty contactor confirming to IEC 60947 capable to withstand 200 times of rated current with ON/OFF push button, with indication for ON position (a) 100 A-1 No (b) 63 A -2 No (b) 16 A -3 No Capacitor :- Air cooled , 440 Volt, delta connected MPP type heay duty , confirming to IS 13340-1993, max transient inrush current 200 In. with discharge resitors , over pressure disconnector , suitable for Overloading as 115% for Over Current and 115% for Over Voltage, Watt Loss <0.5w/kVAr. of capacities (a) 50 KVAR - 01 No, (b) 25 KVAR - 02 No, (c) 10 KVAR - 02 No (d) 5 KVAR -01 No. (iv) Busbar:- 1 set of 300 Amps uniformly rated, 415 V, 3P+1N electrolytic grade copper bus bar of adequate length and cross section with heat shrink colour coded sleeve, supported on F class DMC/FRP insulators

Supplying Installation, Testing & commissioning of floor mounted or free standing (grouted in PCC 1:2:4 type B1), duly labelled with vinyl stickers, modular construction, 7 stage, 415 +/- 10%, 50 +/- 5% HZ, 150 KVAR (in stages) Automatic Power Factor Correction panel , to be operated in Auto and Manual mode, fabricated in minimum 16 SWG CRCA sheet , supported with suitable size base channel not less than 75x75x5 mm, painted in Siemens Gray shade RAL 703, compartmentalised, dust and vermin proof, IP 42 protection, doors and covers with non ageing gasket, doors with concealed hinges with handle and locking facility, cable glands, cable bottom entry for incoming and outgoing cable, danger plate, thermostatically controlled strip heater with provn of double earthing terminals, lifting studs, louvers for proper ventilation with 02 nos Suitable size & capacity but not less than 6 Inches metal/PVC body exhaust fan, with microprocessor based power factor controller neatly bunched control wiring ( with 1 sq mm ) and power wiring with flexible PVC copper cable, adequately supported and routed through cable duct with identification tag seperate cable spacing betwen phase & neutral, alarm during the failure of power supply or in any one phase and comprising of following :- (i) APFC Relay - 3 phase, 7 stage solid state automatic power factor correction relay, directly connected with busbar through suitable size copper conductor , measuring reactive power through CT secondary of rating 5A for operating capacitor bank in steps 2 X 50 KVAR, 1 X 20 KVAR, 2 X 10 KVAR & 2 X 5 KVAR to maintain target PF > 0.98, microprocessor (intelligent) based control circuit.

(ii) Switchgear :- Incoming : 315 AMP MCCB, 36 KA, Ics= 100 % Icu with adjustable Over Load and Short circuit protection -01 No Outgoing :- (a) 100 Amp, 25 KA TPN MCCB -02 Nos. (b) 40 Amp, 10 KA TPN MCB-01 Nos. (b) 16 Amp, 10 KA TPN MCB-04 Nos. (iii) Contactors :- 3 phase Capacitor duty contactor confirming to IEC 60947 capable to withstand 200 times of rated current with ON/OFF push button, with indication for ON position (a) 100 A-2 No (b) 40 A -1 No (b) 16 A -4 No Capacitor :- Air cooled , 440 Volt, delta connected MPP type heay duty , confirming to IS 13340-1993, max transient inrush current 200 In. with discharge resitors , over pressure disconnector , suitable for Overloading as 115% for Over Current and 115% for Over Voltage, Watt Loss <0.5w/kVAr. of capacities (a) 50 KVAR - 02 No, (b) 20 KVAR - 01 No, (c) 10 KVAR - 02 No (d) 5 KVAR -02 No. (iv) Busbar:- 1 set of 400 Amps uniformly rated, 415 V, 3P+1N electrolytic grade copper bus bar of adequate length and cross section with heat shrink colour coded sleeve, supported on F class DMC/FRP insulators

Supplying Installation, Testing & commissioning of floor mounted or free standing (grouted in PCC 1:2:4 type B1), duly labelled with vinyl stickers, modular construction, 11 stage, 415 +/- 10%, 50 +/- 5% HZ, 600 KVAR (in stages) Automatic Power Factor Correction panel , to be operated in Auto and Manual mode, fabricated in minimum 16 SWG CRCA sheet , supported with suitable size base channel not less than 75x75x5 mm, painted in Siemens Gray shade RAL 703, compartmentalised, dust and vermin proof, IP 42 protection, doors and covers with non ageing gasket, doors with concealed hinges with handle and locking facility, cable glands, cable bottom entry for incoming and outgoing cable, danger plate, thermostatically controlled strip heater with provn of double earthing terminals, lifting studs, louvers for proper ventilation with 02 nos Suitable size & capacity but not less than 6 Inches metal/PVC body exhaust fan, with microprocessor based power factor controller neatly bunched control wiring ( with 1 sq mm ) and power wiring with flexible PVC copper cable, adequately supported and routed through cable duct with identification tag seperate cable spacing betwen phase & neutral, alarm during the failure of power supply or in any one phase and comprising of following :- (i) APFC Relay - 3 phase, 11 stage solid state automatic power factor correction relay, directly connected with busbar through suitable size copper conductor , measuring reactive power through CT secondary of rating 5A for operating capacitor bank in steps 1 X 200 KVAR, 2 X 100 KVAR, 2 X 50 KVAR, 2x25 KVAR, 1 X 20 KVAR, 3X10 KVAR to maintain target PF > 0.98, microprocessor (intelligent) based control circuit.

(ii) Switchgear :- Incoming : 1000 AMP MCCB, 50 KA, Ics= 100 % Icu with adjustable Over Load and Short circuit protection -01 No Outgoing :- (a) 360 Amp, 36KA TPN ACB -01 No. (b) 200 Amp, 25 KA TPN MCCB-02 Nos. (c) 100Amp, 25 KA TPN MCCB-02 Nos. (d) 63 Amp, 25 KA TPN MCB-02 Nos (e) 40 Amp 10 KA TPN MCB 01 No (f) 16 Amp 10 KA TPN MCB 03 Nos (iii) Contactors :- 3 phase Capacitor duty contactor confirming to IEC 60947 capable to withstand 200 times of rated current with ON/OFF push button, with indication for ON position (a) 360 Amp - 01 No. (b) 200 Amp - 02 NOs (c) 100 Amp - 02 Nos. (d) 63 Amp-02 Nos. (e) 40 Amp -1 No (f) 16 A - 3 Nos

Capacitor :- Air cooled , 440 Volt, delta connected MPP type heay duty , confirming to IS 13340-1993, max transient inrush current 200 In. with discharge resitors , over pressure disconnector , suitable for Overloading as 115% for Over Current and 115% for Over Voltage, Watt Loss <0.5w/kVAr. of capacities (a) 200 KVAR - 01 No (b) 100 KVAR - 02 Nos. (c) 50 KVAR - 02 Nos. (d) 25 KVAR - 02 Nos (e) 20 KVAR - 01 No, (f) 10 KVAR - 03 No (iv) Busbar:- 1 set of 1200 Amps uniformly rated, 415 V, 3P+1N electrolytic grade copper bus bar of adequate length and cross section with heat shrink colour coded sleeve, supported on F class DMC/FRP insulators

NOTE FOR ITEM NO TO 34.00 TO 38.20 :- The APFC panel shall have following instrumentation, protection, indication among others :- (a) Instrumentation : Digital Multifunction meter in incomer feeder to measure and display voltage, current, frequency, PF, lead/Lag status, total active capacitance, KVARH, KWH,KVAH of suitable range with suitable rating CT of class 0.5 for each phase. (b) Protection :Protections relays for over voltage, over current, earth fault and short circuit protections. Capacitor should have protection of over voltage during switching or re switching by ensuring proper discharge of capacitors. A time delay of min 30sec or above setting should be provided for each bank switching. All the capacitors should not ON simultaneously. Combined lightning and surge protection device for three phase should be connected parallel to the output for providing safety from all types of possible surges. Hooter shall be provided on panel for sounding in case of any acted condition of the protection relay. c) Indication: 01 set of LED bulbs for indication of 3 phase, Auto/Manual mode, ON indication of each stage.

(d) Earthing : A copper earthing bus of adequate current capacity shall be provided and it shall have suitable cross section to carry short circuit fault currents ( min 21 KA for 1 s) to ground. All metallic cases of instruments and other equipment’s in the panel shall be properly earthed through independent copper wire of size not less than 2.5 sq.mm. All hinged doors shall be earthed through flexible earth strap braids. (e) Lighting : Panel lighting shall be provided in the cable/capacitor chamber, which is controlled with panel door open/close limit switch. (f) Meters and control switches shall be located at height which shall be convenient for monitoring and operating. (g) Contractor will provide GA drawing, Control wiring diagram of Automatic Power Factor Correction (APFC) Panel for Approval by GE before placing purchase order. Three sets of final drawings of Automatic Power Factor Correction (APFC) Panel incorporating all changes made. Operation and maintenance manual will be provided by contractor at the time of installation &commissioning. (h) : The stages given in description are minimum. In case of unavailability of required stage controller, next higher stage available will be provided without any financial effect.

Supply and fixing of Three phase IP 54, automatic street light switching controller panel of FR grade material for automatic & switching of street lights based on LUX level of Nature light having sensor, switch alongwith with suitable power contactor of rating 40 Amps 4 pole, MCB SP 40 Amps-03 Nos, complete including testing all as specified and directed.

Material, labour and necessary software for digital mapping LT XLPE UG power cable routes with GPS co-ordinates. The cable route indicator and depth of cable specified at every 100 mtr joints, turninig / diversion or specified, if any by the Engineer-in-Charge alongwith submitting 03 sets of hard copy of drawing for each cable route alongwith tracing and soft copy, duly indicating cable, route indicators, distance from road edge and important land mark enroute on hard and soft copy, complete all as specifed and directed by the Engineer-in-Charge. NOTE :- (i) The contractor will submit, technology / methodology being adopted for digital mapping, UG cable route and submit technical information / specification and obtain prior approval from GE before proceeding with execution of this item. (ii) All necessray T & P, man power, consumables required for execution of this item shall be arranged by the Contractor. (iii) GPS co-ordinates at any point on cable routers on clicking and printion as directed. (iv) The softaware designed shall facilitate future additional / alteration from time to time as required. (v) The software provided for digital map shall be password protected for accessing any amendments. (vi) The software / application designed shall have warrranty for 2 years after completion of entire work. Any trouble shooting / malfunctioned shall be attended without extra cable routes, complete all as specified and directed.

Material and labour for route and depth tracing of LT XLPE insulated UG aluminium conductor cables, 1100 volts grade, any core and size already laid complete cable lengths more than100 mts but not exceeding 1000 mts including necessary tools, plants and machinery complete all as specified and directed by Engr-in-charge.

Material and labour for route and depth tracing of LT XLPE insulated UG aluminium conductor cables, 1100 volts grade, any core and size already laid complete cable lengths more than 1000 mts but not exceeding 2000 mts including necessary tools, plants and machinery complete all as specified and directed by Engr-in-charge.

NOTE FOR ITEM NO 41 .00 TO 42.00 :- 1. The cables are laid underground or on wall/roof and drawn through GI pipes/ducts/trenches etc. Therefore the contractor shall obtain permission of JE and user unit (Whenever necessary) before tracing of cables. 2. The contractor shall arrange necessary tools and technicians/labour for disconnecting cable end terminals if required and the cost of the same is deemed to be included in the rate quoted. 3. Since the work is executed on existing laid cables site for working may be available on restricted hours, hence the contractor shall make his own arrangements and execute accordingly. 4. The contractor shall maintain a register of record as directd b for each cable traced. 5. The contractor is sole responsible for recording the data obtained from these item No 41.00 and 42.00 and accuracy of digital mapping of these cable routes specified in respective items of the contract schedule.

S & F in ground cable route indicators made out of PCC Block in 1:3:6 type C1 using 20mm aggregate of size 25 X 70 x 10 cm marked "MES LT CABLE" duly painted with paint, complete all as specified and directed.

Restringing only existing ACSR conductor on LT pole to the insulaor by means of including necessary binding wire , providing new jumpers etc all as specified and directed by Engr-in-Charge

S&F for stay wire galvanised strand size 7/3.15mm, complete all as specified and directed.

S&F stay assembly complete with 16mm dia stay rod accessories shown in electric plate No 1. Note :- (Loop insulator, stay clamp excavation and concrete measured and paid separately)

S&F for loop type insulator vitreous porcelain white/brown green small size with overall dimension 65x90mm, clearance of hole 16mm for fixing on stay wire.

M&L for PCC (1:4:8) (using 40mm graded aggregate) type D2 for foundation of poles struts & stay assembly etc including necessary form work, all as specified & directed.

M&L for PCC (1:3:6) type C1 in coping of poles etc (using 20mm graded coarse aggregate) including finishing the exposed surface even and smooth without using extra cement and necessary form work all as specified and directed.

S&F for shackle type insulator porcelain , vitreous 100mm high and 115 mm dia complete including glavanised mild steel straps, washer, insulator bolts and nuts suitable for 1100 volts grade.

Supply and fixing OFF Load change over switch 415V in sheet metal enclosure 4 pole 125 Amps Capacity, complete including necessary fixing accessories on wall / panel.

Supply and fixing OFF Load change over switch 415V in sheet metal enclosure 4 pole 160 Amps Capacity, complete including necessary fixing accessories on wall / panel.

Supply and fixing OFF Load change over switch 415V in sheet metal enclosure 4 pole 200 Amps Capacity, complete including necessary fixing accessories on wall / panel.

Supply and fixing OFF Load change over switch 415V in sheet metal enclosure 4 pole 250 Amps Capacity, complete including necessary fixing accessories on wall / panel.

Supply and fixing OFF Load change over switch 415V in sheet metal enclosure 4 pole 315 Amps Capacity, complete including necessary fixing accessories on wall / panel.

Supply and fixing OFF Load change over switch 415V in sheet metal enclosure 4 pole 400 Amps Capacity, complete including necessary fixing accessories on wall / panel.

Supply and fixing OFF Load change over switch 415V in sheet metal enclosure 4 pole 630 Amps Capacity, complete including necessary fixing accessories on wall / panel.

Supply, installation, testing & commissioning of HT 11 KV, 3 Phase, 50 HZ, indoor type, totally enclosed / metal clad switch gear complete with four vaccum circuit beaker (VCB) panel with one incoming and three outgoing having rupturing capacity of 350 MVA, overload, earth fault and shortcircuit protection, Voltmeter range (0-15 KV) and Ammeter (0-400 Amp), required battery bank with charging arrangement including additional adopter panel for fixing with the exisitng VCB & disconnecting existing unserviceable VCB & depositing to MES store Yard etc, complete of following specifications mentioned in IS/IEC 62271-201 incl latest amendments / additions (a) Motorised spring charging mechanism with 24 volt DC universal motor 200 watts and having charging time less than 10 seconds. (b) Earthing switch rated for full making capacity with provision for safe & reliable position indicator. (c) (i) Assembly of Vaccum ciruit breaker shall be completely insulated as per the relevants IS/IEC. (ii) The rating of VCB shall be 11 KV, 400 Amps, 18 KA (for 3 sec), 50 Hz, 3 phase (iii) The vacuum interrupture bottle shall be of the same make of VCB. (iv) Electrically charged and electrically operated independent closing / tripping, trip free, operating mechanism including mannual closing / tripping push button and breaker close / open ption shall be provided. Make: ABB/Siemens/Schneider

v) One bus Bar Chamber including a set of 3 phase 400 Amps copper bus Bars to be provided for further extension in future, if necessary. vi) Strip Heaters with thermostat to be provided with the following specifications :- Power input 80 watts with Voltage rating 230 volts AC Single phase vii) Incomer :- Dual core dual ratio Current Transformer (CT) chamber comprising of 3 Nos, single phase resin cast / ring core CTs of 200-100 / 5+5, burden not less than 15 VA and accuracy class 0.5, for metering, having class 5 P10 for protection as per IS:2705 for each circuit breaker - 01 Sets. viii) Outgoing No-1&2 :- Current Transformer (CT) chamber comprising of 3 Nos, single phase resin cast / ring core CTs of 75-100 / 5+5, burden not less than 15 VA and accuracy class 1.0 for metering, having class 5 P10 for protection as per IS:2705 for each circuit breaker - 02 Sets. ix) Outgoing No-3 :- Current Transformer (CT) chamber comprising of 3 Nos, single phase resin cast / ring core CTs of 75-100 / 5+5, burden not less than 15 VA and accuracy class 1.0 for metering, having class 5 P10 for protection as per IS:2705 for each circuit breaker - 01 Sets. x) 1 No. Potential Transformer (PT), 3 phase, dry type (resin cast) fixed type 11 KV / 110 Volts, Burden 100 VA, Accuracy class 0.5 with HT & LT HRC fuses / MCB for primary and secondary complete all as specified and as directed as per IS: 3156 - 01 Set

xi) Incoming breakers :- SCADA compatible self powered IDMT numerical relays over current & earth fault relay with adjustable setting, high setting short circuit fault relay for complete protection of HT ,11 KV,3 Phase feeder having facility to record fault current with MODBUS communicationon RS 485 communication port - 01 No. including 1 No voltage monitoring relay for under voltage / over voltage protection. xii) Outgoing breakers :- SCADA compatible self powered IDMT numerical relays with high settings for components, over current & earth fault relay with high adjustable setting, short circuit fault relay for complete protection of HT ,11 KV,3 Phase feeder having facility to record fault current with MODBUS communicationon RS 485 communication port - 01 No. including 1 No voltage monitoring relay for under voltage / over voltage protection. xiii) Digital SCADA compatible meter of accuracy class 1, as per IEC 62052-11 / IEC 62053-22 monitoring all electrical parameters like votage & current per phase and Watts, VA, VAR etc. Also to monitor all instanteneous integrated demand,parameters, neutral current, frequency,power factor, % load, % unbalance (V&I), phase angle, THD working on MODBUS protocol. xiv) One set of mechanical indicatior for ON / OFF indication for all LBS / VCB breaker. xv) One set of capacitive voltage indication for R-Y-B xvi) One set of battery and battery charger to provide suitable back up as per OEM's instruction

Note :- 1. Any auxillary fitting/fitments for protection and functioning shall be provided as per the relevant IS. 2. The contractor shall submit GA drawings and techinical specifications of VCB to GE for his approval before placing order. 3. The quoted rate is inclusive of of any adopter panel if required to match with existing HT panel.

Supply, installation, testing & commissioning of HT 11 KV, 3 Phase, 50 HZ, indoor type, totally enclosed / metal clad switch gear complete with two vaccum circuit beaker (VCB) panel with one incoming and one outgoing having rupturing capacity of 400 MVA, overload , earth fault and short circuit protection, ammeter voltmeter range (0-15 KV) and Ammeter (0-400 Amp) required battery bank with charging arrangement including additional adopter panel for fixing with the exisitng VCB & duisconnecting existing unserviceable VCB & depositing to MES store Yard etc, complete of following specifications mentioned in IS/IEC 62271-201 incl latest amendments / additions (a) Motorised spring charging mechanism with 24 volt DC universal motor 200 watts and having charging time less than 10 seconds. (b) Earthing switchrated for full making capacity with provisin for safe & reliable position indicator. (c) (i) Assembly of Vaccum ciruit breaker shall be completely insulated as per the relevants IS. (ii) The rating of VCB shall be 11 KV, 400 Amps, 18 KA (for 3 sec), 50 Hz, 3 phase (iii) The vacuum interrupture bottle shall be of the same make of VCB. (iv) Electrically charged and electrically operated independent closing / tripping, trip free, operating mechanism including mannual closing / tripping push button and breaker close / open ption shall be provided.

v) One bus Bar Chamber including a set of 3 phase 400 Amps copper bus Bars to be provided for further extension in future, if necessary. vi) Strip Heaters to be provided with the following specifications :- Power input 80 watts with Voltage rating 230 volts AC Single phase vii) Incomer :- Current Transformer (CT) chamber comprising of 3 Nos, single phase resin cast / ring core CTs of 200-100 / 5+5, burden not less than 15 VA and accuracy class 0.5 for metering, having class 5 P10 for protection as per IS:2705 for each circuit breaker - 01 Sets. viii) Outgoing No-1&2 :- Current Transformer (CT) chamber comprising of 3 Nos, single phase resin cast / ring core CTs of 75-100 / 5+5, burden not less than 15 VA and accuracy class 0.5 for metering, having class 5 P10 for protection as per IS:2705 for each circuit breaker - 01 Sets. ix) 1 No. Potential Transformer (PT), 3 phase, dry type (resin cast) fixed type 11 KV / 110 Volts, Burden 100 VA, Accuracy class 1.0 with HT & LT HRC & MCB fuses for primary and secondary complete all as specified and as directed as per IS: 3156 - 01 Set x) Incoming breakers :- SCADA compliable self powered IDMT numerical relays L&T, over current with adjustable setting & earth fault relay for complete protection of HT ,11 KV,3 Phase feeder having facility to record fault current with MODBUS communicationon RS 485 communication port - 01 No including 1 No voltage monitoring relay for under voltage / over voltage protection.

xi) Outgoing breakers :- SCADA compliable self powered IDMT numerical relay with high settings for components , over current with adjustable setting & earth fault relay for complete protection of HT ,11 KV,3 Phase feeder having facility to record fault current with MODBUS communicationon RS 485 communication port - 01 No including 1 No voltage monitoring relay for under voltage / over voltage protection. xii) Digital SCADA compatible meter of accuracy class 1, as per IEC 62052-11 / IEC 62053-22 monitoring all electrical parameters like votage & current per phase and Watts, VA, VAR etc. Also to monitor all instanteneous integrated demand, parameters, neutral current, frequency,power factor, % load, % unbalance (V&I), phase angle, THD working on MODBUS protocol. xiii) One set of mechanical indicatior for ON / OFF indication for all LBS / VCB breaker. xiv) One set of capacitive voltage indication for R-Y-B xv) One set of battery and battery charger to provide suitable back up as per OEM's instruction. Note :- 1. Any auxillary fitting/fitments for protection and functioning shall be provided as per the relevant IS. 2. The contractor shall submit GA drawings and techinical specifications of VCB to GE for his approval before placing order. 3. The quoted rate is inclusive of of any adopter panel if required to match with existing HT panel.

Supply, installation, testing & commissioning of HT 11 KV, 3 Phase, 50 HZ, indoor type, totally enclosed / metal clad switch gear complete with two vaccum circuit beaker (VCB) having rupturing capacity of 400 MVA, overload , earth fault and short circuit protection, ammeter voltmeter range (0-15 KV) and Ammeter (0-400 Amp) required battery bank with charging arrangement including additional adopter panel for fixing with the exisitng VCB & duisconnecting existing unserviceable VCB & depositing to MES store Yard etc, complete of following specifications mentioned in IS/IEC 62271-201 incl latest amendments / additions (a) Motorised spring charging mechanism with 24 volt DC universal motor 200 watts and having charging time less than 10 seconds. (b) Earthing switchrated for full making capacity with provision for safe & reliable position indicator. (c) (i) Assembly of Vaccum ciruit breaker shall be completely insulated as per the relevants IS. (ii) The rating of VCB shall be 11 KV, 400 Amps, 21 KA (for 3 sec), 50 Hz, 3 phase (iii) The vacuum interrupture bottle shall be of the same make of VCB. (iv) Electrically charged and electrically operated independent closing / tripping, trip free, operating mechanism including mannual closing / tripping push button and breaker close / open ption shall be provided.

v) One bus Bar Chamber including a set of 3 phase 400 Amps copper bus Bars to be provided for further extension in future, if necessary. vi) Strip Heaters to be provided with the following specifications :- Power input 80 watts with Voltage rating 230 volts AC Single phase vii) Incomer :- Current Transformer (CT) chamber comprising of 3 Nos, single phase resin cast / ring core CTs of 200-100 / 5+5, burden not less than 15 VA and accuracy class 0.5 for metering, having class 5P10 for protection as per IS:2705 for each circuit breaker - 01 Sets. viii) 1 No. Potential Transformer (PT), 3 phase, dry type (resin cast) fixed type 11 KV / 110 Volts, Burden 100 VA, Accuracy class 1.0 with HT & LT HRC & MCB fuses for primary and secondary complete all as specified and as directed as per IS: 3156 - 01 Set ix) Incoming breakers :- SCADA compliable self powered IDMT numerical relay with high settings for components , over current & earth fault relay with high setting for complete protection of HT ,11 KV,3 Phase feeder having facility to record fault current with MODBUS communicationon RS 485 communication port - 01 No including 1 No voltage monitoring relay for under voltage / over voltage protection.

x) Digital SCADA compitable meter of accuracy class 1, as per IEC 62052-11 / IEC 62053-22 monitoring all electrical parameters like votage & current per phase and Watts, VA, VAR etc. Also to monitor all instanteneous integrated demand,parameters, neutral current, frequency,power factor, % load, % unbalance (V&I), phase angle, THD working on MODBUS protocol. xi) One set of mechanical indicatior for ON / OFF indication for all LBS / VCB breaker. xii) One set of capacitive voltage indication for R-Y-B xii) One set of battery and battery charger to provide suitable back up as per OEM's instruction. Note :- 1. Any auxillary fitting/fitments for protection and functioning shall be provided as per the relevant IS. 2. The contractor shall submit GA drawings and techinical specifications of VCB to GE for his approval before placing order. 3. The quoted rate is inclusive of of any adopter panel if required to match with existing HT panel.

Supply, Install, testing & commisioning of power packs unit with battery backup, operating on input AC, 230 Volts and output 24 Volt, DC, 4A complete including taking out existing unserviceable all as directed and specified as follows:- (i) Input :- Suitable for 110 V AC or 230 V AC (+) 20%. (ii) Output burden : less than 50 VA during charging period without output load. (iii) Output : 24 VDC, 100 Wats (nominal). (iv) Battery charging period : 8 hours. (v) Continuous load : 100 watts. (vi) Impulse load : Less than 450 W for not more than 240 msec. (vii) Indication on front display : Charging on, Output on, Output overload, Battery operation, Output switch off. (viii) Battery : 12 Volts, 26 AH (min) - 02 Nos. (ix) Protection : Output side protected for short circuit condition. Note :- Contractor shall submit techinical specification of power packs prior for approval of GE before placing order.

Dismantling, disconnecting necessary HT connection and taking off old vintage OCB breaker and depositing to AGE E/M Adm Area store yard including necessary transportation, tools etc, complete all as specified and directed by Engr-in-charge.

Disconnectng and taking off of HT 11 KV serviceable breakers and transporating to other substations in tech Area as directed and reinstallation tesitng and commissioning including making necessary connection for breakers in & out , control ciruit wiring, etc, complete all as specified and directed by Eng-in-Charge.

Supply, install, testing & commssioning of numerical, programmable IDMT relay with high settings overcurrent & high setting earth fault protection for operation on 3 phase, HT 11 KV system including dismantling disconnecting existing unserviceable relay complete all as directed by Engr-in-charge. The relay shall be operated on auxillary supply 24V-240V, AC/DC & SCADA compatible all as directed. Make :- Model- MC61C-nx in L&T or equivalent in ABB/Siemens Note :-Contractor shall submit techinical specification of relay prior for approval of GE before placing order. Contractor should ensure compatibility of relay with existing system where the same is going to be installed.

S & F in ground cable route indicators made out of PCC block in 1:3:6 type C1 using 20 mm aggreagate of size 30 x 80 x10 cm marked "MES HT CABLE" and painted complete all as specified and directed.

Material, labour and necessary soft ware/hard ware for digital mapping of HT XLPE UG cable routes with GPS co-ordinates. The cable route indicator and depth of the cables specified at every 100 mts, joints, turnings/diversions or specified if any by Engineer - in-Charge along with submitting 03 sets of hard copy of drawings for each cable route tracing sheet with distance marked from road edge and important lank mark enroute and soft copy duly indicating cable route indicators, complete all as specified and directed by the Engineer-in-Charge. Note: (i) The contractor will submit, explain and demostrate the technology / methodology being adopted for digital mapping, UG cable route and submit technical information / specification and obtain prior approval from GE before proceeding with execution of this item. (ii) All necessray T & P, man power, consumables required for execution opf this item shall be arranged by the Contractor. (iii) GPS co-ordinates at any point on cable routers on clicking and printion as directed. (iv) The softaware designed shall facilitate future additional / alteration from time to time as required. (v) The software provided for digital map shall be password protected for accessing any amendments.

Material and labour for route and depth tracing of HT XLPE insulated aluminium conductor UG cables, 11000 volts grade, any core and size already laid including necessary tools, plants and machinery complete of cable lengths more than 100 mts but not exceeding 1000 mt all as specified and directed by Engr-in-charge. Note - 1. The UG cables are laid underground or on wall/roof or drawn through GI pipes/ducts/trenches etc. Therefore the contractor shall obtain permission of JE/Engr-in-charge for any shutdown if required as these cables are energized. 2. The contractor shall arrange necessary tools and technicians/labour for disconnecting cable end terminals if required and the cost of the same is deemed to be included in the rate quoted. 3. Since the work is executed on existing laid cables site for working may be available on restricted hours, hence the contractor shall make his own arrangements and execute work accordingly. No claim is allowed on account of loss of man hours, the quoted rate is deemed to be inclusive for the same. 4. The vender shall maintain a register of record as directed by Engr-in-charge for each cable traced alongwith GPS CO-Ordinates. 5. The contractor is sole responsible for recording the data obtained from these items and accuracy of digital mapping performed here in after of these cable routes subsequently in respective items of the contract schedule.

6. The software designed shall faciliate future addition/alteration from time to time. 7. The software provided for digital map shall be password portected for accessing and any ammendments thereafter on account of expansions/alterations.

Material and labour for route and depth tracing of HT XLPE insulated aluminium conductor UG cables, 11000 volts grade, any core and size already laid including necessary tools, plants and machinery complete of cable lengths more than 1000 mts but not exceeding 2000 mt all as specified and directed by Engr-in-charge. Note - 1. The UG cables are laid underground or on wall/roof or drawn through GI pipes/ducts/trenches etc. Therefore the contractor shall obtain permission of JE/Engr-in-charge for any shutdown if required as these cables are energized. 2. The contractor shall arrange necessary tools and technicians/labour for disconnecting cable end terminals if required and the cost of the same is deemed to be included in the rate quoted. 3. Since the work is executed on existing laid cables site for working may be available on restricted hours, hence the contractor shall make his own arrangements and execute work accordingly. No claim is allowed on account of loss of man hours, the quoted rate is deemed to be inclusive for the same. 4. The vender shall maintain a register of record as directed by Engr-in-charge for each cable traced alongwith GPS CO-Ordinates. 5. The contractor is sole responsible for recording the data obtained from these items and accuracy of digital mapping performed here in after of these cable routes subsequently in respective items of the contract schedule.

6. The software designed shall faciliate future addition/alteration from time to time. 7. The software provided for digital map shall be password portected for accessing and any ammendments thereafter on account of expansions/alterations.

Material and labour for route and depth tracing of HT XLPE insulated aluminium conductor UG cables, 11000 volts grade, any core and size already laid including necessary tools, plants and machinery complete of cable lengths more than 2000 mt all as specified and directed by Engr-in-charge. Note - 1. The UG cables are laid underground or on wall/roof or drawn through GI pipes/ducts/trenches etc. Therefore the contractor shall obtain permission of JE/Engr-in-charge for any shutdown if required as these cables are energized. 2. The contractor shall arrange necessary tools and technicians/labour for disconnecting cable end terminals if required and the cost of the same is deemed to be included in the rate quoted. 3. Since the work is executed on existing laid cables site for working may be available on restricted hours, hence the contractor shall make his own arrangements and execute work accordingly. No claim is allowed on account of loss of man hours, the quoted rate is deemed to be inclusive for the same. 4. The vender shall maintain a register of record as directed by Engr-in-charge for each cable traced alongwith GPS CO-Ordinates. 5. The contractor is sole responsible for recording the data obtained from these items and accuracy of digital mapping performed here in after of these cable routes subsequently in respective items of the contract schedule.

6. The software designed shall faciliate future addition/alteration from time to time. 7. The software provided for digital map shall be password portected for accessing and any ammendments thereafter on account of expansions/alterations.

S & F FRP /Polystyrene / SMC junction box, three phase complete with backelite connector 4 Nos 20 Amps bus bar capacity 4 way supported on FRP / DMC insulator, MCB SP 06 Amps capacity with necessary fixing arrangement by providing MS clamps 1 Nos made out of MS flat 25x3 mm painted with one coat of primer and two coats of paint including nut bolts etc. Make Snitex Code GSJB-3126/HENSEL cat No DK1616 G or equivalent make in National / Protech

S & F PVC insulated and PVC sheathed three core copper conductor of size 1.5 Sqmm drawn in and including medium grade rigid PVC conduit with fixing / clamping accessories for connecting from bus bar box to street light fittings complete all as specified and directd of approved Make.

S & F 40 mm GI tubing 40 mm dia light grade with all necessary fixing arrangements fixed to walls, poles, under road / floor etc for cable protection, complete all as specified and direceted.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thixkness in hard / soft loose soil, complete all as specified and dirceted.

Removing excavated material to a distance not exc 50 mtr and depositing where direceted at a level not exc 1.5 mtr above the starting point.

SANJEEV ENTERPRISES

SAGGI ELECTRIC COMPANY

Third Wave Services Pvt Ltd

RAVINDRA SALES