ELECTRICAL WORKS IN EVM STORAGE AT RANIPET

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLSH copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories except ceiling rose and round sheet with flexible hose 0.25 meter, Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points/Coil). (Higher End)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLSH copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories except ceiling rose and round sheet with flexible hose 0.25 meter, Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points/Coil). (Higher End)

Supply and fixing 9W/10W Round LED Fitting (Bath & Toilet)

Supply and fixing of 4 Feet LED 20W Fitting with LED 20W tube (HigherEnd)complete withTW round blocks on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting

Supply and fixing of LED Twin Fitting 20 W with high brightness LED fitting on wall or ceiling, with PVC unsheathed leads from terminals to the fitting. ( Havells /Equivalent )

Supply and fixing of Aesthetically desined ultra modern 18W Round surface Mounting luminaire with high brightness LED fitting on wall or ceiling, with PVC unsheathed leads from terminals to the fitting. (Havels / Equivalent )

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED on false Ceiling with suitable hanging support from ceiling with PVC usheathed copper leads from terminals to the fitting.

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 300 mm down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300 mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall and Supply and fixing of louvers shutters arrangements for 300 mm (12") sweep (light duty) AC exhaust fan.

Supply and fixing of 375 mm (15") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall and Supply and fixing of louvers shutters arrangements for 375 mm (15") sweep (light duty) AC exhaust fan.

Supply and fixing of 60W LED Street Light fitting complet with 32mm dia GI pipe (Class B) with 1no 32mm GI bend complete on the existing post/ wall with SMC box with 16A fuse unit with PVC unsheathed copper leads from fuse carrier to the fitting, MS clamps and aluminum painting with including necessary labour (Havels/Philips/Equivalent)

Supply and fixing of 3nos.6/16 A two module 3 pin socket , 3 nos. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 20Amps DP Plug and Socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) (Legrand / Hager make).

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB as incoming and 10 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End

Supply and fixing of 4 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 No 32A 4P MCB as incoming and 12 Nos 6A to 32A SP MCB as outgoing in flush with wall with Earth connection only. Higher End

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End(For Ese-1 No and 1 No Non Esen)

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with suitable colour

Supply and run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed portion with suitable colour ( From Panel to Vertical DB's)

Supply and frxing of brass cable gland for 3 1/2x150 sqmm PVC armoured LTUG cable with earth connection

Supply and clamping of 3 1/2 x150 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and laying of 3 1/2 x150 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and providing cable end termination of 3-1/2x150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of 250 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with Earth connection only.

Supply and erection of 250Amps capacity dust and vermin proof cubical panel board size of 5'X 5' X 2' made up of 16 SWG CRCA sheet steel for outer body, with doors, switch supports and seperations etc., and with supply and fixing of the following interior switch with bus bar chamber complete with Bus Bar (a)25 x 10mm tinned cu flat for Inter connections, (b)25 x 6mm tinned cu flat for Interconnections and earth connections with bus bar insulators complete with the following tinned Cu flat should be used between busbar and switches for interconnection. Interconnection of bus bars : (1)250A TPN switch bus bar for Interconnection 25mmX10mm copper flat, (2)125 A TPN outgoing switch disconnector fuse units 25mm X6mm tinned cu. Flat supply and fixing of KWh meter (Submeter) & indication lamps. The panel should be fabricated as per IE rules & CEIG specification.The housing accommodate the following switches. Incoming Switch : (1)250 A TPN Incoming switch disconnector fuse units interior only with HRC fuses double break- 1 Nos, Outgoing Switch Switches : (2)125A A TPN Incoming switch disconnector fuse units interior only with HRC fuses double break-6Nos The panel board should be painted with two coats of high quality epoxy paint over one coat of red oxide primer with superscriptions. (lettering and numbering) The above cubical panel board rest on suitable angle iron base.

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and fixing of 65 mm (21/2 ") GI Pipe (class 'B') of 6 mt Length with 300 mm x 300 mm x 6mm MS base plate duly welded at the bottom with concerting with construction of Masonary pedestal with suitable MS box to house the 10A DP MCB two way connector on suitable hylem sheet and supply and fixing of 1x90W LED Type street light fitting (Make : Philips /Havells )with 1 meter of 32 mm dia GI Pipe (class 'B' ) complete with necessary cowl arrangements on the above post with PVC unsheathed leads with painting of suitable colour

Supply and frxing of brass cable gland for 4 x 16 /25 sqmm PVC armoured LTUG cable with earth connection

Supply and laying of 4 x 16 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and clamping of 4 x 16 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of 150W LED flood light fiting complete with angle iron frame supports with suitable clamp sets on the existing post / wall with PVC unsheathed copper leads MS camps and aluminium painting.

Supply and fixing of 50W Gate light on the existing post/ wall with PVC unsheathed copper leads from terminal to the fitting. (Make: Havells / Equivalent)

Supply and erection of 2.0 Ton capacity ( 3star Rated) Split type Airconditioner unit confirming to ISI 1301 (part-2) 1992 with amendment No.1 fitted with Hermetically sealed compressor operationon 230V 50Hz AC supply system with refrigerant gas R-22 suitable for high wallmounting evaporator and specification as under general requirement interconnection of pipes abd cable.(SR) (Make: Blue Star, Carrier, Voltas.)

Supply and erection of 5KVA capacity Automatic Voltage stabilizer suitable to operation on 230 volts, single phase,50Hz,AC supply system with tie delay relay and High/Low voltage cut off, input voltage range 170V to 270V AC single phase, wall mounting type stabilizer with necessary clamp. (SR)(V-Guard)

Supply and fixing of Copper pipe to connect Indoor and Outdoor units

Supply and fixing of MS stand for fixing outdoor unit.

Supply and fixing of water drain pipe line (1" PVC pipe)

Supply and Installation of 4MP IP Colour bullet Camera ,WDR 3.6 mm Fixed lens. Make:Hikvision

Supply and installation of 32 channel Network Video recorder , H.264/MJPEG dual code decoding upto 200 Mbps incoming bandwidtht support 2 SATA HDDs up to 8 TB . Make : D-link/Eq.

Supply and Installation of 8-port poE 2 Gigabit managed switch, which supports

Supply and Installation of 8TB built in Hard Disc Drive.Make: Seagate/Eq.

Supply and laying of CAT -6 cable in existing PVC pipe on wall and ceiling.Make :D-link/eq

Supply and Installation of 4U wall rack, with front glass door with lock and key facilities

Supply and Installation of 1KVA UPS

Supply and Installation of 55" Colour TV/Moniter including all accessories Model :Samsung or sony or equivalent

Supply and fixing of Delegate unit (Make : Bosch)

Supply and fixing of Wall Speaker 30W (Make : Bosch)

Supply and Installation of Conference Type Controller

Supply and fixing of Cordless Mic UHF with Controller arrangements

Supply and run of 8 core Shielded copper Mike cable

Supply and run of 2 of 1.5 sqmm Shielded copper Speaker wire

Supply and installation of 12U Rack with Accessories

Supply and installation of PA mixer 500 W Amplifier

Supply and Installation of 3600 ANSI Lumens Projector, XGA ( 1024 x 768 ) Resolution Contrast Ratio 20000:1

Supply and Installation of 8' x 6' Motorized Screen

Supply and Installation of 3 Feet Ceiling Mount Kit.

Supply and Installation of 20 Meter HDMI Cable

Supply and Installation of 3 core 1.5 Sq.mm PVC Power cable for projector

Supply , Testing Commissioning and Handing over of 1no 58.5 KVA Diesel Generator set(Make Kirlokar/Asoke Leylend/Cummins) of 0.8 P.F three Phase 415V/420volts,50C/S 1500 RPM CPCB-IV Approved capacity compressing of Developing 156 BHP Water cooled clock wise rotating with 46 KW / 58.5 KVA operating capacity Brush Less Alternator close coupled underneath fuel tank ,standard safeties, LLOP With stop solenoid ,battery with lead ,Electric start and Anti Vibration mountings and accessories and AMF control panel as detailed below including transporting and Unloading charges (A) Engine: Water cooled diesel engine suitable for Generator application with a shaft out put of 74BHP at 1500 RPM under NTP conditions. The Engine shall comprise the following standard fitting flexible coupling fly wheel, ai cleaner, fan blower, radiator, water pump, fuel filter, lubricating oil filter, etc. (B) 12/24 Volt Electronic starting Equipment: Complete with starter motor, dynamo, standard batteries with cable, flexible exhaust piping of 50cms length. (C) ENGINE INSTURMEN PANEL / MOUNTED: Starting push botton / starting key, lubricating oil, temperature gauge, lubricating oil pressure gauge, water temperature gauge, safety control for low lubricating oil, pressure, safety control for high water temperature, safety control for over speed, hour meter (mechnical ) and RPM indicator, battery charging ammeter.

The engine should be capable of providing 10% over load for one hour for every 11 hours continuous at full load. (D)ALTERNATOR: 58.5 KVA /46 KW Capacity Brushless Alternator AC 3phase 50c/s 415/420V 0.8PF 1500 RPM under NTP conditions conforming to IS 13364 (part - II) 1992 to be means of coupling. Note:- (1)The control panel should be complete with necessary fuses, cables, label, other accessories with neutral isolation arrangements. (2)The engine should trip for the following: (a) Low lubricating oil pressure, (b) High water temperature, (c)Over speed, 3.Supply and fitment of Auto Mains Failure Panel, 1 EB Service wih 200 Amps switch and contactors SUF Control relays, timers etc suitable for auto change over of DG & EB Service. F.FUEL TANK :Fuel tank of 165 litres capacity and with inlet and outlet connections, level indicator with scale etc., G.BASE FRAME: Base frame should be fabricated with MS channel frame of rigidly welded construction for mounting of generaor set. The engine and alternator should be coupled by suitably designed diaphragm type flexible coupling with guard and mounted on the base frame wih proper alignment. H) ACOUSTIC ENCLOSURE: The Acoustic enclosure, Self standing weather proof KG- CPCB-IV Typed Acoustic canopy KG 125WS floor mounting type with modular construction with the provision to assemble and dismantle easily and designed to suit all weather condtions.

(13)1 set DC control relays incorporating engine start/ stop and failure to start / lockout, (14)1 set selecor switch auto/ manual, (15)1 no Push button "Start", (16)1 no Push button "Stop", (17) 1 no Push button "Reset", (18)1 No signal lamp for indicating load on mains, (19)1 no signal lamp for indicating load on set, (20)1no signal lamp for indicating set fails to start., (21)1no signal lamp for indicating set running, (22)1No signal lamp for indicating battery, (23)1set Pilot lamps of 3 nos, (24)MCCB of 250A capacity with magnetic thermal overload release, instant start circuit trip and under voltage release switch., (25)Rectangular copper bus bars (1No for each phase, neutral and earthing terminals) of adequate capacity duly colour coded with head shrinkable PVC sleeves, (26)1No mains voltage monitor, (27)Hooter/Audio alarm for indicating set fails to start and for DG O/L., (28)1set Timers, (29)Audio and Visual indicator arrangements for:(a)Low lubricating oil pressure, (b)High water temperatur, (c) Over speed, (30)1No Earth fault relay, (31)Isolator to isolate the neutral, Note:-(1) The control panel should be complete with necessary fuses, cables, label, other accessories with neutral isolation arrangements., (2)The engine should trip for the following: (a) Low lubricating oil pressure, (b) High water temperature (c) Over speed

Erection of Genset:- Providing suitable concrete foundation with cement concrete 1:2:4 with sand cushion around the foundation erection of 58.5KVA Generator set over the exisiting foundation and erection of Generator set with proper alignment over the existing foundation to suit 58.5KVA Generator set Foundation size L2900xW1100xH1580mm.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps/ supports on wall/ floor/ ground for earth connection.

Supply and installation of exhaust piping of sufficient length with suitable MS pipe so as to extend outside the generator room with necessary thermal insulation

Supply of lubricating oil to run the Generator set for minimum of 8 hours by supply of 200 litres diesel

Supply and frxing of brass cable gland for 3 1/2x95 sqmm PVC armoured LTUG cable with earth connection

Supply and clarnping of 3 1/2 x95 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and laying of 3 1/2 x95 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and providing cable end termination of 3-1/2x95 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and laying of LTUG cable in a trench digging of ground of depth 2 ft X width 2 ft X length 3 ft and construction of wall with bricks of height 1 1/2 ft on either side with cement mixture and filling of 12mm jelly of depth 1/2 ft with 1/2 cement mixture. (A)Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. (B)Cement concrete 1:5:10 (One of cement, five of sand and ten aggregate) using 40mm gauge hard broken granite stone jelly for flooring including dewatering if found necessary and laid in layers of not more than 15cm thick etc., complete. (C)Brick work in Cement Mortar 1:5 using best quality II class ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for the following including curing, etc., (D)Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., E)Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. F ) Supplying and filling in foundation, basement, etc with filling M sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc

Please Enable Macros to View BoQ information