REPAIR / MAINT OF INTERNAL

Amount

Supply and fixing in replacement of sheet steel enclouser distribution boards, double door factory made TPN Vertical 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB and 12 outgoing MCBs circuits comprising of 3 phase 4 wire of suitable rating complete all as spcd and directed with the following accessories :-( For out going MCB & MCCB 100 AMPS 3 Pole measured and paid for separately)

Supply and fixing in replacement of sheet metal enlosure for DBs when MCBs to be used double door factory made flush fixed complete with 100 amps rated bus-bar 240 volts single phase 6 ways including necessary brick work and plaster to match with the existing surface complete all as specified.

Supply and fixing in replacement of sheet metal enlosure for DBs when MCBs to be used double door factory made flush fixed complete with 100 amps rated bus-bar 240 volts single phase 8 ways including necessary brick work and plaster to match with the existing surface complete all as specified.

Supply and fixing in replacement of sheet metal enlosure for DBs when MCBs to be used double door factory made flush fixed complete with 100 amps rated bus-bar 240 volts single phase 12 ways including necessary brick work and plaster to match with the existing surface complete all as specified.

Supply and fixing in replacement of busbar chamber 250 Amp 4way factory made complete with locking arrangement including necessary brick work and plaster to match with the existing surface complete all as specified.

Supply and fixing in replacement of MCCB 100 Amps , AC 415 Volts 16KA 3 pole including making connections with suitable size of aluminium lugs all as specified and directed.

M&L for Point wiring for MT Garages/Tank garages/hangers with 1.5 sqmm (Nominal area ) 1100 Volt PVC Insulated , FRLS unsheathed and multi stranded copper conductor cable in and including new PVC Concealed conduit 20mm dia 1.5mm thick for one light / fan point or bell point controlled by one 5 Amp switch (including cutting chases and making good the distributed surfaces) and fixing new 3mm thick hylam sheet top cover, sheet screws and sunken boxes after removing old unserviceable laminated sheeet and sunken boxes included 1.5 Sqmm stranded copper conductor with green PVC Insulation earth contunity conductor connected to common earth dolly etc. complete all as specified and directed. Note : The cost of sunken boxes and bakellite sheet is included in the quoted rate)

All a per item No 8 here in before but one three pin socket outlet 5 Amps independent board complete

All a per item No 8 here in before but one three pin 5 Amps socket outlet on the same board with other switches

All a per item No 8 here in before but with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 2.5 Sq mm copper solid conductor connecting to common earth dolly complete.

M&L for point wiring concealed type with PVC insulated (unsheathed ) cable 1.5 Sq mm (Nominal area) multi stranded FRLS copper conductor 1100 V grade & continuous earth wire PVC insulated 1.5 Sq mm copper solid conductor connecting to common earth in and existing PVC conduit but fixing new sunken boxes for one light /fan/ buzzer point controlled by one 5 Amp switch one way 3mm thick hylem sheet top cover, sheet screws and after removing old unserviceable hylem sheet (including cutting chases & making good the disturbed surface) complete all as specified and directed by Engineer-in-Charge. . Note : The cost of bakellite sheet , sunken boxes is included in the quoted rate)

All as per Srl item No 12 here in before but for one 5 amps socket out let independent complete all as specified.

All as per Srl item No 12 here in before but on the same board completeall as specified

All a per item No 12 here in before but with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 2.5 Sq mm copper solid conductor connecting to common earth dolly complete.

Supply and Fixing in replacement switch piano type 6 Amps one way 230 volts AC complete all as specified and as directed

Supply and Fixing in replacement socket outlet 5 pin, 6 Amps flush type 230 volts AC complete all as specified and as directed

Supply and Fixing switch piano 16 Amps type one way 230 volts AC complete all as specified and as directed

Supply and Fixing in replacement socket outlet 6 pin 6/16 Amps multi purpose flush type 230 volts AC complete all as specified and as directed

Supply and fixing in replacement ceiling rose 65X50 mm two to three terminals complete all as specified.

Material and labour for replacement of lamp holder insulated body with 10 Watt LED Bulb, back plate batten/angle type for batten fitting fixed on bakelite sheet 100mm x 100mm 230V AC cool day light 6500K having maximum height 1020mm heavy duty complete all as specified.

Supply and fixing in replacement fan regulator, electronic step type heavy duty socket type 230 volts complete all as specified and as directed.

Supplyand fixing in replacement of MCB 'C' series breaking cap 10 KA single pole 6 to 32 Amps all as specified and directed

S & F in replacement of MCB 40 amps'C' series breaking cap 10 KA single pole with neutral, AC 230 volts complete all as specified and directed.

Supply and Fixing in replacement Bell push flush type 6 Amps one way 230 volts AC complete all as specified and as directed

Supply and fixing in replacement of bell Ding Dong AC 230 volts complete all as specified and as directed

Supply & fixing in replacement of single pole and neutral sheet metal enclosures with two pin & earth plug and socket complete with one single pole MCB of 20 Amps complete all as specified and as directed.

Taking down aluminium point wiring from existing conduit / batten (light, fan, socket or power) complete such as switches, ceiling rose, pendent, regulators, socket, light fittings etc and removing material from site and making good the disturbed surface of wall / floor etc, complete all as specified and directed

M&L for point wiring with 1.5 sqmm (Nominal area ) 1100 Volt PVC Insulated, FRLS unsheathed and multi stranded copper conductor cable in and including new PVC Concealed conduit 20mm dia 1.5mm thick for one light / fan point or bell point controlled by one 5 Amp switch (including cutting chases and making good the distributed surfaces) and fixing new 3mm thick hylem sheet top cover, sheet screws and sunken boxes after removing old unserviceable plastic laminated sheeet and sunken boxes included 1.5 Sqmm stranded copper conductor with green PVC Insulation earth contunity conductor connected to common earth dolly etc . complete all as specified and directed Note : The cost of sunken boxes and bakellite sheet is included in the quoted rate)

All as per item No 29 here in before but one three pin socket outlet 5 Amps independent board complete

All as per item No 29 here in before but one three pin 5 Amps socket outlet on the same board with other switches complete.

All as per item No 29 here in before but with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 2.5 Sq mm copper solid conductor connecting to common earth dolly complete.

Supply and fixing in replacement of sheet steel enclouser distribution boards, double door factory made TPN Vertical 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB and 12 outgoing MCBs circuits comprising of 3 phase 4 wire of suitable rating complete all as spcd and directed with the following accessories :- (a) MCCB 100 amps, 25 KA, TP, 415 volts, 50 Hz = 01 No. (Note:- Out going MCB shall be measured and paid for separately)

S&F in replacemnt of MCCB four pole thermal adjustable type 200 Amp 25KA fixed magnetic with tripping arrangment with factory made enclosure including necessary brick work and plaster to match with the existing surface complete all as specified.

M&L in replacement of sub main wiring 6 Sqmm multi-strand PVC insulated copper conductor FRLS cable including PVC insulated copper conductor cable of size 6 Sqmm as cotinuous earth wire connecting to common earth including connections of cable with MCBs or bus bars complete all as specified and directed

M&L in replacement of sub main wiring 4 Sqmm multi-strand PVC insulated copper conductor FRLS cable including PVC insulated copper conductor cable of size 4 Sqmm as cotinuous earth wire connecting to common earth including connections of cable with MCBs or bus bars complete all as specified and directed

M&L in replacement of sub main wiring 2.5 Sqmm multi-strand PVC insulated copper conductor FRLS cable including PVC insulated copper conductor cable of size 2.5 Sqmm as cotinuous earth wire connecting to common earth including connections of cable with MCBs or bus bars complete all as specified and directed

S&F Regid non-metallic PVC conduit of size 25mm dia including of all accessories and all fittings such as Tees,bends, elbows, reducers, bell mouth, tube ends and fixing accossories such as couplers,lock nuts, saddles, pipe hook etc complete all as specified and as directed

Supply and fixing in replacement LED tube light fixture 18watt LED 6000K (Industrial box type including tube rod) , decorative ultra slim linear with extruded polycarbonate environmental friendly energy efficient ready to use pack complete all as specified and directed

Supply and fixing in replacement LED tube light fitting tube lighting fixture 9 watt LED 6000K , decorative ultra slim linear with extruded polycarbonate environmental friendly energy efficient ready to use pack complete all as specified and directed

Supply and fixing in replacement of LED T-8 tube light fitting with single side connection polycarbonate LED tube rod 18/20W 4 feet 1 x 18/20 watt box type including rotary type bipin holder and connection with PVC insulalted twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed.

Supply and fixing in replacement of automatic monoblock pressure/booster pump size 25mm x 25mm, tech motor S1 class B 230 Volt 500 HZ, RPM 2800, 10 MF, input power 650 watt with pressure tank of cap 19 ltrs PS max pressure bar 10 PT test pressure bar 14 with complete accessories incl GI Pipe/gate valve/NRV complete all as specified and directed.

Supply and fixing in replacement light bracket wall mounting decorative type LED fitting upto 1x8/11 W mini including lamp Complete all as specified and directed.

Supply and fixing in replacement Environment friendly , energy efficient , aesthetically designed circular shaped decorative wall/ceiling light LED Fixture 12 W LED 6K with opal diffuser to give glare free light complete all as specified and directed,

Supply & fixing in replacement of 6 watt Square/Round recess mounted down lighter separate replaceable electronic driver celling cut out 104mm x 104mm height 30mm square shaped polycarbonate fixture complete all as specified and directed,

Supply & fixing in replacement of 12Watt Square/Round recess mounted down lighter separate replaceable electronic driver celling cut out 155mm x 155mm height 32mm square shaped polycarbonate fixture complete all as specified and directed,

Supply & fixing in replacement of 15Watt Square/Round recess mounted down lighter separate replaceable electronic driver celling cut out dia 104 mm height 30mm round shaped polycarbonate fixture complete all as specified and directed,

Supply & fixing in replacement of 18Watt Square/ Round recess mounted down lighter separate replaceable electronic driver celling cut out dia 155 mm height 32mm round shaped polycarbonate fixture complete all as specified and directed,

Supply and fixing in replacement decorative LED wall light fixture including lamp made up of polycarbonate light fitting city-3 suitable for 9Watt complete all as specified and directed

Supply & fix in replacement of LED Security Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens.

Supplying and fixing in replacement LED bulk head light fittings 10 watt white including LEDstrip as per IP65 in engineering plastic housing withclear prismatic diffuser and making necessary connections complete all as specified

Supply and fixing in replacemnt of looking mirror LED light decorative type wall mounting SS finish fixture with opal glass diffuser suitable for 11W incandescent lamp with lamp complete all as specified and directed.

Supply and fixing in replacemnt of LED tube light fitting 1x36 watts decorative mirror optics luminaire including LED rod with anodised aluminium louvers and white engineering plastic end cover complete with, rotory type bipin holder and including connection with PVC insulated three core 23/0.0076 flexible copper cable from ceiling rose to tube light fitting complet all as specified and directed.

Supply and fixing in replacemnt of LED tube light fitting 1 x 28 watts decorative mirror optics luminaire including tube rod with anodised aluminium louvers and white engineering plastic end cover complete with rotory type bipin holder and including connection with PVC insulated three core 23/0.0076 flexible copper cable from ceiling rose to tube light fitting complet all as specified and directed.

Supply only in replacemnt single side connection polycarbonate LED tube Rod 18/20W, 1.2 mtr length output 6000 to 6500 lumens 220V AC white effect complete all as specified and directed by Engineer-in -charge.

Supply and fixing Exhaust fan AC 230Volts 300mm ventilair DX high quality engineering plastic complete with louvers and shutters complete all as specified and directed . make Khaithan,Orient,Havells

Supply and fixing in replacemnt of bed light fancy type with9 watt LED lamp complete all as specified and directed.

Supply only in replacement LED slim panel cygnus series recess/surface/suspended mounting LED slim ceiling light 2'x2' with extruded aluminium housing and milky diffuser, suitable for recess mounted size 595x595mm complete with LED tube.

Supply and fixing in replacement bracket made out of GI pipe 40 mm medium grade 1.2 mtr long made to shape with fixing clamps of MS flat 40x6mm nut bolts etc for security light all as specified and directed

Supply & fixing in replacement of integral post top lanterns complete with Black ABC plastic spigot, spun aluminium funnel shape with clear acrylic cover light opening on canopy with baffles and accessories with 10watt LED lamp complete all as specified and directed

Supply & Fix in replacement of flood Light Luminaire 120 watt with .high power SMD LED cool white, CRI 75, +/- 5% supply voltage 220/240/50 Hz, light engine driver base, pole adapter, powdre coated in IP 66 Incliding protection over temperature should be from the same manufacturer Product complete all as specified and directed

Supply & Fix in repair flood Light Luminaire 150 watt with .high power SMD LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter, powdre coated in IP 66 Incliding protection over temperature should be from the same manufacturer Product complete all as specified and directed

Supply and Install in replacement of Off Load Change over switch 415 Volts in sheet metal enclouser 4 Pole of capacity minimum 100 Amps complete all as specified and directed.

Supply and fixing ceiling fan 1200mm Sweep copper winding,high speed, Aluminium body with blade, double ball bearing of BEE star rated Including acessories connector, canopy, Hanging Rod and clamps , including electric connection with pvc flexible twin core copper wire from ceiling rose to ceiling fan complete all as specified and directed

Supply and fixing in replacemnt of 40mm dia tube light grade galvanised with all fittings complete to wall or for garden lights or laid in floors for cable protection including cutting chases and necessary brick work and plaster work to making good the distributed surface complete all as specified and directed.

Material and labour for PCC (1:3:6) TYPE C-2 using 40mm graded stone aggregate as in foundation / coping of light complete all as specified and directed.

Supply and Fixing only in replacement modular fan step regulator, heavy duty 230 volts , 2 module complete all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade ) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 5 of SSR PART 1 , with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switche, DBs) complete all as specified & testing on completion.

Supply and laying or fixing in replacement 1100 Volts grade heavy duty cable with PVC insulated aluminium standard conductor served with an inner sheathing of PVC tape and over all PVC Sheathed in service connections , one twin core 10 Sqmm cable standard conductor cable flat or circular all as specified and directed by Engineer- in- Charge.

Supply and laying or fixing in replacement 1100 Volts grade heavy duty cable with PVC insulated aluminium standard conductor served with an inner sheathing of PVC tape and over all PVC Sheathed in service connections , one twin core 6 Sqmm cable standard conductor cable flat or circular all as specified and directed by Engineer- in- Charge.

Supply only in replacemnt of FTL Rod 36W, 1.2 mtr length output 3250/3500 lumens 220V AC white incandescent effect complete all as specified and directed by Engineer-in -charge.

Supply only in replacemnt LED Bulb 230V AC 9/10 watt cool day light 6500K having maximum height 1020mm heavy duty complere all as specified and directed by Engineer-in -charge.

Supply only in replacemnt of CFL 230V AC 20 watt ELT enery saving lamps white light 2700K having maximum height 114 mm heavy duty complete all as specified and directed by Engineer-in -charge.

Supply and fixing single the static whole current electronic energy meter single phase 10-60 Amps two wire of accuracy class 1.0, as per IS 13779 power factor unity to zero (all power factor lag/or lead ). starting current : 0.40 % lb , current 240 volt,50 Hz with LCD display. The meter shall be able to recording in Kwh/KVAH, MD, current load, V, Amp, Freq, etc burden of voltage circuit shall not exceed 1 VA. The shall have IEC 1107 port and shall be DLMS compatible for data reading. The meter should be immune to DC magnitic fields as per the CBIP 304. The meter should record the anti tamper features under the conditions mentioned as reversal of line load terminals, interchanging of phase and neutral wires, drawing of load by disconnecting neutral of meter & out going earth, meter body opening, neutral disturbance with transparent the pilfer proof meter box (PPMB) suitable to house single phase staatic energy meter. The meter shall be wall mounted type and have ability so as to offer protection of electrical equipment. High grade fire retardant Engineering plastic (Acrylonitrile butadiene styrene /Polycorbonate, with minimum thickness 2.00 mm necessary sealing with lead meter and appropriate size copper lugs and necessary PCC work if reqd with existing surface complete at no extra cost including the fwg works including taking out existing meter and handed over to AGE E/M store Yard. (a) Connection of incomming and outgoing service cable /submain cable with meter is included in the quoted rate. (b) Sealing with the name of AGE E/M Punch and with lead seal and gi standard sealing wire.(c ) LCD test and display of all reading with battery back up for accessing reading during absence of electric supply. (d) The rate shall be included for testing and commissionoing alongwith preparation of documentation and submitting in triplicate.

M&L in replacement of single core wiring 10 Sqmm multi-strand PVC insulated copper conductor FRLS cable including connections of cable with MCBs or bus bars complete all as specified and directed

M&L in replacement of single core wiring 6 Sqmm multi-strand PVC insulated copper conductor FRLS cable including connections of cable with MCBs or bus bars complete all as specified and directed

M&L for point wiring concealed type with PVC insulated (unsheathed ) cable 1.5 Sq mm (Nominal area) multi stranded FRLS copper conductor 1100 V grade & continuous earth wire PVC insulated 1.5 Sq mm copper solid conductor connecting to common earth in and existing PVC conduit, and sunken boxes but fixing new 3mm thick plastic laminated sheet top cover,sheet screws and after removing old unserviceable plastic laminated sheet (including cutting chases & making good the disturbed surface) complete all as specified and directed by Engineer-in-Charge. Note : The cost of suitable size MS housing box and frame plate sheet are included in the quoted rate)

All as per Srl item No 77 here in before but for one 5 amps socket out let independent complete all as specified.

All as per Srl item No 77 here in before but on the same board completeall as specified

All a per item No 77 here in before but with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 2.5 Sq mm copper solid conductor connecting to common earth dolly complete.

Supply and Fixing of Modular switch 6 Amps one module 230 volts AC complete all as specified and as directed

Supply and Fixing Modular socket, 6A -2/3 pin combined 2 module, 230 volts AC complete all as specified and as directed

Supply and Fixing Modular switch 16 Amps one module 230 volts AC complete all as specified and as directed

Supply and Fixing Modular socket 6A/16A, 2/3 pin combined, two module 230 volts AC complete all as specified and as directed

Dehydration of old transformers oil by heating and making breaking cap upto 35 KV complete all as specified and directed.

Repair to self starter including taking out from veh Tata Xenon /Tata 207 dismantling including supply and replacement of the fwg spares parts, reassmbling, commissioning and testing all as directed by Engr-In-Charge:-

Solonoid switch

Self armature

Copper brush set

Re-tapping of field coil

Repair to self starter including taking out from veh EICHER dismantling including supply and replacement of the fwg spares parts, reassmbling, commissioning and testing all as directed by Engr-In-Charge:-

Solonoid switch

Self armature

Copper brush set

Re-tapping of field coil

Repair to self starter including taking out from veh Car Ambassador dismantling including supply and replacement of the fwg spares parts, reassmbling, commissioning and testing all as directed by Engr-In-Charge:-

Solonoid switch

Self armature

Copper brush set

Re-tapping of field coil

Repair to clutch system including dismantling and supply & replacement of fwg spares/parts including reassembling and testing complete all as specified and directed:-

TATA XENON 207/EICHER

Clutch plate

Pressure plate

Clutch release bearing

Clutch cylinder lower

Clutch cylinder upper

CAR AMBASSADOR

Clutch plate

Pressure plate

Clutch release bearing

Clutch cylinder lower

Clutch cylinder upper

Repair to rediator by dismatling and taking out rediator from vehicle including opening of upper tank and lower tank and rectify the leakage by gas welding of copper tube and cleaning of rediator tube with acid and re- assembling the same after testing and commissioning complete all as specified and directed for TATA Xenon/TATA 207.

Repair to rediator by dismatling and taking out rediator from vehicle including opening of upper tank and lower tank and rectify the leakage by gas welding of copper tube and cleaning of rediator tube with acid and re- assembling the same after testing and commissioning complete all as specified and directed for EICHER.

Repair to rediator by dismatling and taking out rediator from vehicle including opening of upper tank and lower tank and rectify the leakage by gas welding of copper tube and cleaning of rediator tube with acid and re- assembling the same after testing and commissioning complete all as specified and directed for Car Ambassador.

Dismantling and taking out defective water pump from vehTata Xenon/ EICHER supply and fix new water pump after testing and commissioning complete all as specified and directed.

Dismantling and taking out defective water pump from veh Car ambassador supply and fix new water pump after testing and commissioning complete all as specified and directed.

Repair to suspension system including supply and replacement of the fwg for EICHER

Suspension bush kit

Tie rod end rod set

Ball joint

Shock absorbers make: Gabrial

Repair to suspension system including supply and replacement of the fwg for Car Ambassador:-

Suspension bush kit

Tie rod end rod set

Ball joint

Shock absorbers make: Gabrial

Taking out defective silencer assembly and replacing the same with new for TATA-207/EICHER/Car Ambasdor including replacing of the following parts complete all as specified and directed.

Crown wheel pinion

Bewel for differential system

Yoke and teeth

Repair to differential system including taking down UNSV defective part and supply and replacement of the fwg for TATA Xenon/207:

wipper machine with motor

Ignation switch with key set

Indicator/ brake light assembly

Head light assembly

Fog Light

Alternator assembly complete

Door lock assembly

Light and left mirror

Mud flap

Horn assembly complete set

Repair and replacement including taking UNSV defective parts and supply and fixing the fwg for EICHER:-

wipper machine with motor

Ignition switch with key set

Head light assembly

Fog Light

Alternator assembly complete

Right and left mirror

Mud flap

Glass winder

Door lock assembly

Indicator/brake light assembly

Repair and replacement including taking UNSV defective parts and supply and fixing the fwg for Car Ambassador:-

Wipper machine with motor

IgnItion switch assembly

Head light assembly

Fog Light

Complete altenator assembly

Right and left mirror

Mud flap

Glass winder

Cut out fuse

Fuel pump assembly

Petrol pipe

Door lock assembly

Indicator/ brake assembly

Taking out fuel pump assembly and calibration with authrised wksp and re-fixing the same after testing and commissioning complete all as specified and directed for EICHER.

Taking out fuel pump assembly and calibration with authrised wksp and re-fixing the same after testing and commissioning complete all as specified and directed for Car Ambassador.

Removing old paint of veh cabin body, bumper, bounet & metalic surface with the help of blow lamp and rubbing with sandy paper complete all as specified and directed for EICHER.

Removing old paint of veh cabin body, bumper, bounet & metalic surface with the help of blow lamp and rubbing with sandy paper complete all as specified and directed for Car Ambassador.

Making good surface by denting welding patch work and apply putty prepared mettalic surface for paint for paint complete all as specified and directed for EICHER.

Making good surface by denting welding patch work and apply putty prepared mettalic surface for paint for paint complete all as specified and directed for Car Ambassdor.

Painting complete body of vehicle with two coat of red oxide paint and two coat of enamel paint with spray painting complete all as specified and directed for EICHER.

Painting complete body of vehicle with two coat of red oxide paint and two coat of enamel paint with spray painting complete all as specified and directed for Car Ambassador.

Taking out UNSV driver cabin seat assembly from veh repair the seat with the help of welding/replacing spring nut bolts etc and replacing and fixing new foam and superior quality rexine cloth and refixing the same to veh complete all as specified and directed for Veh TATA Xenon 207/EICHER

Taking out UNSV driver cabin seat assembly from veh repair the seat with the help of welding/replacing spring nut bolts etc and replacing and fixing new foam and superior quality rexine cloth and refixing the rear and front seat assembly same to veh complete all as specified and directed for Veh Car Assembly.

M & L in replacement of seat cover for rear seat and front seat complete all as specified and directed for Car Ambassador.

M & L in replacement for foot mat set complete all as specified and directed for EICHER.

M & L in replacement for foot mat set complete all as specified and directed for TATA Xenon 207.

M & L in replacement for foot mat set complete all as specified and directed for Car Ambassador .

Repair overhauling to 4 wheel brake assembly including replacing the fwg for EICHER complete all as specified and directed:-

Wheel cylinder assembly

Break shoe assembly set of two

Front wheel disc brake set

Brake master cylinder

Repair overhauling to 4 wheel brake assembly including replacing the fwg for Tata Xenon /Car Ambassador complete all as specified and directed:-

Wheel cylinder assembly

Break shoe assembly set of two

Front wheel disc brake set

Brake master cylinder

Servicing of veh including cleaning nipple gresing, engine tune up valve setting and replacing the fwg :-

Oil filter

Diesel filter

Air filter

Wheel bearing

Computer wheel alisgment

Testing of PUC certificate from authorized civil Govt Authority

Cotton wastage

Differential system oil 90 grade

Radiator coolent

Repair to name/number plate front/rear by replacing the UNSV number plate made out from MS Sheet duly writing of unit name, BA No, formation sign, Bdg classification in redium letter in front and rear side of veh.

M & L for replacement of old engine oil from the vehs and cleaning the oil sump throughly supply & filling new engine oil grade 20W 40 of Make : Servo super of Indian Oil all as specified and direcred by Engr-In Charge.

Servicing of motor cycle and repairing, cleaning washing greasing including replacement of fwg items:-

Air Filter

Clutch plate

Clutch chain

Main chain

Clutch housing

Seat cover

Indicator light

Brake show

Clutch wire

Mud guard rear

Battery Exide dry type

Brake wire

Oil filter

Repair to aluminium ladder cabin / folding type trolley mounted of height 32/27 feet including Removing the existing rusted / broken angle iron - 01 Job, Supply and welding new MS Angle iron of size 50 x 50x 5mm - 30 Kg, Taking out single drum winch with pully assembly with wire rope and repair/replacement - 01 Job, Supply and fixing in replacement wire rope of size 1/5" dia - RM and Taking out 04 wheels with shaft and replacing with eixting size- 04 Nos.

Dismantling of electric motor for rewinding with supper enameled copper wire of suitable gauge and complete servicing of air compressor and reassembling the same after repair/replacemnet of Pressure gauge- 01 Nos, Pressure air pipe- 01 Nos, Gate valve- 01 Nos, Fan Belt- 01 Nos

Scrapping and rubing with emery paper of complete body air/water compressure and painting of air compressure with one coat of red oxide and two coat of enameled paint complete all specified and directed.

Dismantling of electric motor for rewinding of water compressure with supper enameled copper wire of suitable gauge and complete servicing of compressor and reassembling the same after repair/replacemnet of fwg parts:-

Water filling pipe, 3 ply heavy duty dia 6 mm suitable for water compressor - 10 RM

Brass nozel- 01 Nos

Pressure guage - 01 Nos

Supply and fixing inreplacement of inner tube with rubber ring complete size 2.75x18.

Supply and fixing inreplacement of inner tube with rubber ring complete size 165R/80.

Supply and fixing inreplacement of inner tube with rubber ring complete size 215R/75.

Supply and fixing inreplacement of inner tube with rubber ring complete size 7.50x16.

Material and labour for recondioning of lead acid battery capacity 80AH complete all as specified and directed.

Material and labour for recondioning of lead acid battery capacity 100AH complete all as specified and directed.

To depute service representative minimum for 01 visit to attend the DG set at frequency as per schedule or after 250 working hours. Service Representative will Carry scheduled preventative maintenance checks on Diesel Generating Set (of any make ) and carry out the the undermention Jobs during his visit for DG Set 25 KVA to 30 KVA. (A) Check List for minimum core of work (i) Check the sample of coolant concentration (ii) Check the fan belt for tension and inspect it. If needs any replacement (iii) Check the exhaust mani fold out let (iv) Examine the charge level of the battery and check for any loose connection (v) Check the air cleaner components and clear them if any dirt occurs (vi) Check and adjust the voltage level of the battery charger (vii) Drain out water from the container of the bottom of the filter housing and fuel tank (viii) Checking of control panels wiring, instrumentation, contactor fuses etc. (ix) Check the serviceability of safety controls of engine (x) Checking of all electrical connections for its proper tightness (xi) Check AVR connections & power cable connections for tightness (xii) Check the RPM/frequency and adjust it. (xiii) Check the condition of wire breaded/nonbreaded hoses of engine. (xiv) Checking of load balancing of alternator/AMF panel output

Ditto as items No 2 above but DG Set of Cap 40 to 65 KVA

Ditto as items No 2 above but DG Set of Cap 100 to 250 KVA

Servicing of DG Set including replacement the Diesel filter, company approved make for DG Set of cap 25 to 30 KVA

All as per item here in before but Lub oil filter.

All as per item here in before but Radiator hose pipe set.

All as per item here in before but Fan belt.

All as per item here in before but Air filter element

Servicing of DG Set including replacement the Diesel filter, company approved make for DG Set of cap 40 to 65 KVA

All as per item here in before but Lub oil filter.

All as per item here in before but Radiator hose pipe set.

All as per item here in before but Fan belt.

All as per item here in before but Air filter element

Servicing of DG Set including replacement the Diesel filter, company approved make for DG Set of cap 100 to 250 KVA

All as per item here in before but Lub oil filter.

All as per item here in before but Radiator hose pipe set.

All as per item here in before but Fan belt.

All as per item here in before but Air filter element

Dis-connecting the fuel pipes from the Fuel Injection Pump Assembly, taking out the FIP assembly from the engine body and transporting to the workshop to carry out the following for DG of 25 to 30 KVA (i) Dis-mantling the complete FIP, taking out all the parts, cleaning the internal/external surfaces of the pump (ii) replaceing the suction & delivery valves, rollers and other worn out parts. (iii ) Assembling the parts, filling correct grade of oil ,testing for smooth functioning. (iv) Calibrating the FIP for correct fuel pressure. (v) Transporting the FIP from the workshop to site and fitting the FIP assy to the engine.

Dis-connecting the fuel pipes from the Fuel Injection Pump Assembly, taking out the FIP assembly from the engine body and transporting to the workshop to carry out the following for DG of 40 to 65 KVA (i) Dis-mantling the complete FIP, taking out all the parts, cleaning the internal/external surfaces of the pump (ii) replaceing the suction & delivery valves, rollers and other worn out parts. (iii ) Assembling the parts, filling correct grade of oil ,testing for smooth functioning. (iv) Calibrating the FIP for correct fuel pressure. (v) Transporting the FIP from the workshop to site and fitting the FIP assy to the engine.

Dis-connecting the fuel pipes from the Fuel Injection Pump Assembly, taking out the FIP assembly from the engine body and transporting to the workshop to carry out the following for DG of 100 to 250 KVA (i) Dis-mantling the complete FIP, taking out all the parts, cleaning the internal/external surfaces of the pump (ii) replaceing the suction & delivery valves, rollers and other worn out parts. (iii ) Assembling the parts, filling correct grade of oil ,testing for smooth functioning. (iv) Calibrating the FIP for correct fuel pressure. (v) Transporting the FIP from the workshop to site and fitting the FIP assy to the engine.

M & L for draining out old engine oil from the DG Set and replace with new oil at recommended by manufacturer complete all as specified and directred.

Repair overhalling of self starter including replacement of worn out clutch assembly bush, spring, plunger assembly, solenide switch, corbon brushs, spring etc for the DG set of cap 25 to 30 KVA.

All as per item here in before but of capacity 40 KVA to 65 KVA

All as per item here in before but of capacity 100 KVA to250 KVA

M & L for topping up of water coolent in radiotor of DG set TVS Girling/volvo line or of equivelent make all as directed by EIC.

Cleaning of the fuel tank of DG sets of following capacity after decaning the diesel, through cleaning with kerosene oil including replacement of level indicator pipe complete all as directed by EIC of cap 25 KVA 30 KVA.

All as per item here in before but of capacity 40 KVA to 65 KVA

All as per item here in before but of capacity 100 KVA to250 KVA

Dismantling and removing of water pump assesmbly complete from the engine repair/overhauling the same by replacing worn out components like bearing,impeller,bushes,oil seal,water seal,gasket etc. reassembling,refixing and testing complete for DG set of cap 25 KVA to 30 KVA.

All as per item here in before but of capacity 40 to 60KVA

All as per item here in before but of capacity 100 KVA to 250 KVA

Reapair/overhaling of dynamo/ charging alternator including replacement carbon,brushesholder,spring,commutator/slipring assembly bearing,regulator etc. of any make,type and capacity.

Supply and fix in replacement of automatic voltage regulator suitable for DG set of 25 KVA to 30 KVA rating.

All as per item here in before but of capacity 40 KVA to 63 KVA

All as per item here in before but of capacity 100 KVA to 110 KVA

M&L for replacement of electrically operated fuel shut down valve assembly for 25 to 250 KVA DG set complete testing and commissioning as specified and directed by EIC.

M & L for replacement of moulded rectifier assembly complete as per exisiting one of 25 to 250KVA alternator excitor unit complete all as specified & directed .

M & L for replacement of PVC flexible wire breded fuel pipe suitable for Gen set of capacity 25 KVA to 250 KVA complete all as specified & directed .

Dismantling of radiator of DG set and for servicing/cleaning with dismantling twin tanks, replacement of gasket packing , nuts ,bolts , washers ,descaling with appropriate chemical and welding copper brazing of damazed fins/tubes and reassembling & refixing of 25 KVA to 30 KVA capacity in same position after testing complete all as specified & directed .

All as per item here in before but 40 KVA to 65 KVA

All as per item here in before but 100 KVA to 250 KVA

M & L for replacement of flexible rubber cuopling suitable for DG set 25 KVA to 110 KVA complete all as specified & directed .

M & L for replacement of engine start relay 12/24 Volts. Make:- PIC / Technica/ Indo Econ complete all as specified & directed .

Repair to battery 12 Volt 180 AH including removing of old cell/plate and supply and replacement of positive plate /cell and negative plate / cell filling of electrolight 1150 gravity chargeing fix on gen and taking complete all as spd and directed by EIC.

M & L for replacement of battery terminals brass with steel nuts, bolts & washers .

M & L for replacement of PVC insulated battery lead stranded copper conductor of size 50 Sq mm suitable pices with bothend copper lugs complete all as specified & directed .

Painting of DG set by scrapping of old paint complete and painting with two coats of synthetic enamel paint over a coat of red oxide primer and writing SM/MES No of 25 KVA to 30 KVA size complete all as specified & directed.

All as per item here in before but 40 KVA to 65 KVA

All as per item here in before but 100 KVA to 250 KVA

Dismantling of exhaust mani fold assembly complete and repairing, cleaning complete with wire brush necessary welding and refixing with required new bolts/nuts complete all as directed for DG set of 25 KVA to 250KVA Capacity.

Taking out the old rusted silencer in beteween exhaust pipe engine and providing new low noise silencer (Residential type) and fixed with gasket, nutbolts washer and asbestoss rope complete all as specified and directed for DG set of 25 KVA to 250KVA Capacity.

Repair/replacement of injector nozzle including testing pressure as per required for DG set of 25 KVA to 30 KVA size complete all as specified & directed.

All as per item here in before but 40 KVA to 65 KVA

All as per item here in before but 100 KVA to 250 KVA

M & L in replacement for Changeover switch 200 Amp off load side handle 4 pole, 415 Volt complete all as specified & directed .

M & L in replacement for Changeover switch 63 Amp off load side handle 4 pole, 415 Volt complete all as specified & directed .

M & L in replacement for Changeover switch 100 Amp on load side handle 4 pole, 415 Volt complete all as specified & directed .

M & L in replacement for Changeover switch 200 Amp on load 4 pole, 415 Volt complete all as specified & directed .

M & L in replacement for 63 Amp MCCB, 4 pole, 25 KA , 415 Volt complete all as specified & directed .

M & L in replacement for 100 Amp MCCB, 4 pole, 25 KA , 415 Volt complete all as specified & directed .

M & L in replacement for 250 Amp MCCB, 4 pole, 35 KA , 415 Volt complete all as specified & directed .

M & L in replacemet of control wiring of DG Set as per existing size of copper wire connected complete to the panel with provision of all wiring codes all as reqd insert the panel.

Supply only distilled water for battary complete all as specified & directed.

Supply and fixing in replacement of asbestoss rope for exhuest pipe complete all as specified & directed.

M & L for in replacement of fuel tank cubical/cylindrical type made up of 2mm thick MS sheet for accomodating 200/250 ltrs diesel complete all as specified & directed.

Dis-connecting the alternator from the engine by removing the coupling, transporting the alternator complete to workshop for repairs: upto 63 KVA (i) Rewinding and Cleaning the armature complete, applying one coat of varnish and heating complete (ii) replacing the damaged rectifier unit including filter circuit elements complete. (iii ) replacing the wornout carbon brushes – 01 set Assembling the alternator complete at workshop and testing at NO load , transporting the same to the site , connecting the alternator to the engine after proper alignment including replacement of coupling , key complete all as directed by the engineer in charge.

Dis-connecting the alternator from the engine by removing the coupling, transporting the alternator complete to authorized maintenance service center for repairs: 100 to 250 KVA (i) Rewinding and Cleaning the armature complete, applying one coat of varnish and heating complete (ii) replacing the damaged rectifier unit including filter circuit elements complete. (iii) replacing the wornout carbon brushes – 01 set Assembling the alternator complete at workshop and testing at NO load , transporting the same to the site , connecting the alternator to the engine after proper alignment including replacement of coupling , complete all as directed by the engineer in charge.

M & L for scraping the existing paint of Canopy of DG set , Cleaning the rusted portion complete , and applying two coat colour of existing paint all as required at site from 25 to 63 KVA.

M & L for scraping the existing paint of Canopy of DG set , Cleaning the rusted portion complete , and applying two coat colour of existing paint all as required at site from 100 to 250 KVA .

Repair/maint of EOT crane 5.00 Ton/ 2.00 Ton cap in frequency of every 6 months ,checking of control panel, control wiring, gear box, limit switches horizontal/Cross / Up / down travel, motors gear box etc including oiling, greasing, load testing complete all as specified and directed by Engr-In-Charge.

Supply & fix in replacement travelling cable copper conductor 03 Core 6 Sqmm

All as per item here in before but 4 Sqmm

Supply and fix in replacement of control panel comprising of the fwg:- (i) Contactor 415 volt, 32 Amp, 03 pole- 06 Nos. (ii) Timer switch- 02 (iii ) Relay- 02 Nos (d) Control panel wiring- 01 Job

Supply and fix in replacement of limit switch

Supply and fix in replacement of wire rope 3/4" dia

Supply and fix in replacement of wire rope 1/2" dia

Taking out electric motor 2 HP dismantling , taking out burnt winding wire and rewinding with new supper enameld copper wire baking, vernishing etc and reassembling testing complete.

Taking out electric motor 3 HP dismantling , taking out burnt winding wire and rewinding with new supper enameld copper wire baking, vernishing etc and reassembling testing complete.

Supply and fix in replacement of bearing suitable for 2 HP motor

Supply and fix in replacement of bearing suitable for 3 HP motor

Supply and fix in replacement of long travel shaft pillar block bearing as per existing size.

Supply and fix in replacement mannual operated suspended type control switch panel consisting of push botton 08 Nos for up/down, reverse, fwd, start and stop.

Servicing/reparing of AMF Panal for DG Set capacity 25 KVA to 63 KVA 3 Phase, 415 Volt including disconnecting the all connection and taking out old UNSV item, replacing the fixed/moving parts ,contactor,relay and cleaning dust and providing the proper size of lugs, nuts and bolts complete all as specified and directed (Note: Materials/parts for replacement will be measure and paid seperatley

Servicing/reparing of AMF Panal for DG Set capacity 100 KVA to 250 KVA 3 Phase, 415 Volt including disconnecting the all connection and taking out old UNSV item, replacing the fixed/moving parts ,contactor,relay and cleaning dust and providing the proper size of lugs, nuts and bolts complete all as specified and directed (Note: Materials/parts for replacement will be measure and paid seperatley

Supply and fix in replacement battery charger SMPS 12 Volt 6 Amp all as sp and directed.

Supply and fix in replacement line voltage Monitor (Digital) 3 Phase 415 V all as sp and directed.

Supply and fix in replacement contactor 100 Amp 3 Phase 4 pole 415 V all as sp and directed.

Supply and fix in replacement contactor 400 Amp 3 Phase 4 pole 415 V all as sp and directed.

Supply and fix PVC insulated single core multistrands copper wire 50 sqmm all as sp and directed.

Supply and fix digital VAF meter 3 phase 415 V all as sp and directed.

Supply and fix inreplacement of Indicator complete all as sp and directed.

Supply and fix Micro processor based Gen Set Controle 12 Volt all as sp and directed.

Supply and fix Micro processor based Gen Set Controle 24 Volt all as sp and directed.

Supply and laying, in replacement, of LT underground cable XLPE insulated, inner PVC sheathed, galvanized steel strip armoured, PVC sheathed electric power cable with stranded compact aluminium conductor 1100 volts grade 50 Sq mm 4 core all as sp and directed . Note : The cost of Aluminium thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it.

Servicing/reparing of 30 KVA to 50 KVA 3 Phase, 415 Volt servo voltage stablizer complete including disconnecting the all connection and taking out old UNSV item, cleaning and servicing the fixed/moving contract and blowing and dust and providing the proper size of lugs, nuts and bolts and new control wiring and replace of the fwg items including transporting to workshop and return back after repair complete all as specified and directed (Note: Materials/parts for replacement will be measure and paid seperatley

Material and labour for disconnecting /opening the UNSV variable transformers of 30 KVA to 50 KVA and rewinding the variable transformers with super enamelled copper winding as per existing gauge including insulations material cotton tape, varnish , insulation paper, sleves and drying/baking to proper temparature complete all as specified and directed.

Supply in replacement of PCB circuit board relay etc complete all as specified and directed.

Supply in replacement of LT bushing male/Female complete all as specified and directed.

Supply filling and topping of new transformers oil low viscocity type of die electric strength 35 to 40 KV breaking cap conforming to IS complete for outdoor / indoor types stablizer complete all as specified and directed.

Supply and fix in replacement of Galvanised iron strip 32x6mm burried in the ground/pipe/wall and dully connected to machinery with nuts bolts washers and thimbles complete all as sp and directed.

CHINAR ENGINEERS AND BUULDERS

Intrernational Engineers

M/s. Saffron Construction Co

Ghuman Builders

KARACHI ELECTRIC & TRADING CO.

M/S MAHAJAN CONSTRUCTION CO

AVTAR SINGH RAJU

M/s MAHAJAN CONSTRUCTION CO.