SPL REPAIR TO TOILET, BATHROOM AND KITCHEN OF BLDG. NO P 01, P 03 AND P 77 OF SANJOG CHETRI VIHAR AND OTHER SANCTION WORK UNDER GE (EAST) LUCKNOW

Amount

Demolition of cement concrete (unreinforced ) in floors and pavings not exc 15cm thickness (above or below GL) complete all as specified and directed

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed.

Taking down cement or cement lime plaster or stone / brick wall, ceiling including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutter from the frame) area not exc 1.5 sqm each complete with hold fasts etc complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutter from the frame) area exc 1.5 sqm but not exc 4.0 sqm each complete with hold fasts etc complete all as specified and directed.

Taking down shutters of any description exc 1.00 sqm but not exc 2.00 sqm and easing, ajusting and also refixing builders hardware as required and renewal of unserviceable screws and refixing in the same opening complete all as specified and directed.

Taking down shutters of any description not exc 1.0 sqm each shutter complete all as specified and directed.

Taking down shutters of any description exc 1.0 sqm and not exc 2.00 sqm each shutter complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6M mean radius, old size brick built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick/stone masonary surfaces in cement mortar (1:4), finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering on other than fair faces of brick/stone masonary surfaces in cement mortar (1:6), finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement, complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick rendering in cement mortar in CM (1:4) on ceiling finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) mixed with water proofing compound @ 3 % by weight of cement on other than fair faces of brick / stone masonary surfaces, finished even and smooth without using extra cement, complete all as specified and directed (Note:-WPC shall be measured and paid separately 'Only')

M&L for 40mm thick PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregae) as in roof padding, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in floors etc complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exc 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

M&L for non skid coloured ceramic tiles, joint free 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm in floors with borders, incl over 15mm thick screed bed in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors complete all as specified and directed.

M&L for glazed ceramic coloured tiles 7 to 8mm thick in vertcial surfaces of size exc 0.11 sqm but not exc 0.18 sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed plaster in cement mortar 1:4 complete all as specified and directed.

All as per item No 23 above but in skirting over 10mm thick screeding in cement mortar 1:4 complete all as specified and directed.

M&L for glazed ceramic tiles (coloured) 600x300x7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering (as screed bed) in cement & sand mortar 1:4, complete all as specified and as directed.

M&L for 16 to 18mm thick granite (of any type) work (table rubbed and polished ) in steps, jambs, pillars, window -cills, cooking platforms and like pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding of edge laid over 15mm thick screed bed in CM (1:6) including rounding of edge of stone slabs one edge complete all as specified and directed.

S&F of pressed steel frames of size 105 x 60mm for doors with one or more rabtes includin necessary fixing lugs, hinges, lock strike plate, etc ocmplete all as specified and directed.

S&F of pressed steel frames of size 125x60mm for doors with one or more rabtes includin necessary fixing lugs, hinges, lock strike plate, etc ocmplete all as specified and directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commerical type on both sides complete all as specified and directed.

S&F solid PVC frame (Single Rebated ) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified and directed.

S&F of factory made solid PVC profiled panel door shutter 28 mm thick with interal skin as frame & 3 mm thick high pressure compact laminate on both side of approved colour as infill, with 'C' type GI or 40 x 20 x 19 of MS pipe as stiffner & fixing in frame at site as per specifications & drawing etc complete all as specified and directed.

S&F for steel windows with side hung shutters including projection type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed and welded,complete all as specified and directed.

S&F for steel windows with side hung shutters including projection type hinges with steel handle, and steel peg stay complete without glazing bars, dovetailed and welded, complete all as specified and directed.

M&L in repairs 18/19mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations, fixed with screws, including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and pelment boxes, cupboard, shelves etc complete all as specified and directed.

S&F continous (Piano) hinges, mild steel, bright finish, width of flaps (when open) 30mm complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of apertature 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of apertature 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

S&F 3mm thick glass, ordinary quality, 3mm thick fixed with oil putty size of glass not exc 0.50 sqm in each pane, complete all as specified and directed.

S&F 3mm thick figured glass, pin head type and glazing with oil putty in square not exc 0.50 sqm in each pane, complete all as specified and directed.

S&F MS butt hinges, medium weight, cold rolled, ISI marked of size 100mm, complete all as specified and directed.

S&F 100mm butt hinges stainless steel with galvanised mild steel hinge pin anodised ISI marked complete all as specified and directed.

S&F in repair MS butt hinges, medium weight, cold rolled, ISI marked of size 100mm, complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F hasp & staple 100mm size safety type, aluminium anodised with mild steel hinges pin including bolt of hinge plate & fixed with screws complete all as specified and directed.

S&F 300mm long alumimium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed.

S&F 140mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed.

S&F in repair PVC coated, MS curtain rods 22-25mm dia with and including fixing of two Nos MS brackets and decorative type PVC knobs at both ends of curtain rod complete all as specified and directed.

M&L for framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders; framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290, Gde- E-165 complete all as specified and directed.

S&F in repair Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F rolled mild steel section as in main and cross beam, hip and jack rafter, purlinewhere connected to common rafter and running rail and guides for sliding door, fixed with angle cleat or other connecting plates, confirming to Fe-410W (Gde-E-250) quality-A, complete all as specified and directed.

M&L cutting holes in brick walls (not exc half brick) for inserting hold fasts and making good dismantled portion in PCC 1:2:4 (20mm aggregate) and cement mortar 1:3 complete all as specified and directed.

M&L for mild steel work such as hold fasts, hooks, clamps etc and similar work conforming to Fe-290, (Gde-E -165) complete all as specified and directed.

Taking down old unserviceable 15mm UPVC tubing, fittings and connections and removing from site complete all as specified and directed.

Taking down old unserviceable 20mm UPVC tubing, fittings and connections and removing from site complete all as specified and directed.

Taking down old unserviceable 25mm GI tubing, fittings and connections and removing from site complete all as specified and directed.

S&F 15mm GI water tubing (concealed type), medium grade, galvanised with all fittings and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

S&F 20mm GI water tubing, medium grade, galvanised with all fittings and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

S&F 25mm GI water tubing, medium grade, galvanised with all fittings and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

Refixing old 25mm GI tubing galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

M&L for dismantling of existing unserviceable RCC/PVC water tank and S&F 500 Litres capacity rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position complete all as specified and directed.

M&L for disconnectiong existing tanks exc 250 Ltr & not exc 500 Ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc and hoisting if required reconnectiong and refixing in position complete all as specified and directed.

S&F in repair 1000 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of existing one complete all as specified and directed

S&F ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe of 20mm dia and fixed (minimum weight 210 gms) complete all as specified and directed

S&F in repair tubular towel rail, chromium plated brass 20mm dia 'D" type 60cm long between flanges complete all as specified and directed.

S&F in repair brass chromium plated shower rose of 125mm size with swivel joints, including fixing to steel pipe or union of 15mm bore complete all as specified and directed.

S&F in repair PVC valve less, syphonic action type flushing cistern, 10 Litre capacity, low level, white with inlet, ball vlave float, handle including PVC rigid pipe 32mm bore as flush pipe fixed on walls by drilling holes and using PVC rawl plug of suitable size complete all as specified and directed.

S&F in repair wash hand basins vitreous china, coloured flat back size 550 x 400mm fixed including bracket complete all as specified and directed.

S&F in repair PVC connection, heavy duty 15mm bore, 45cm long with 2 Nos PTMT nuts of approved quality complete all as specified and directed.

S&F in repair 15mm bore brass CP mixer valve wash basin for mixing hot and cold water screwed down for iron pipe complete all as specified and directed.

S&F in repair 15mm bore cast copper alloy chromium plated bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in copings, bed plates, plinth courses, parapets and the like including weathering, slightly rounded or chamfered angles and throating including use and waste of necessary form work etc complete all as specified and directed

S&F 15mm bore cast copper alloy chromium plated bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed.

S&F in repair angle valves 15mm bore , cast copper alloy chromium plated with long sunk and cap (Concealed type), screwed down high pressure screwed both ends for iron pipe or for unions and fixed etc complete all as specified and directed.

S&F in repair sinks without drainage board made of stainless steel 1mm thick kitchen with plugs washers and waste pipe, etc complete, including bedding in cement mortar to dwarf wall or including fixing cantilver brackets and connecting union to pipe overall size 495mmx420mm bowl 410mm x 330mm x160mm complete all as specified and directed

S&F in repair vitreous china wash down water closet pan pedestal pattern, including P or S trap and connection to drain (or outgoing pipe) and PVC seat cover excluding flushing cistern and flush pipe complete all as specified and directed.

Supply only liquid water proofing compound of approved quality, ISI marked complete all as specified and directed.

Supply only liquid water proofing compound of approved quality, ISI marked complete all as specified and directed.

Dismantling of old ceiling boards any type and any thickness including cover fillets/ aluminum snap grid complete all as specified and directed

M&L false ceiling with 4 mm thick E-board white prelaminated set embossed reinforced designer ceiling board of approved texure fixed with GI imposed grid frame work of size not more than 600 x 600 mm having 24 mm wide T- section, runner made of 0.33 mm GI sheet and angle made of 0.45 mm GI sheet, suspended with 2 mm dia GI wire including two coat of oil bound distemper complete all as specified and directed

Taking down 100mm / 75mm dia AC rain water pipe (any size or pattern) including all fitting, heads, shoes, bends and removing from sites complete all as specified and directed. (Note:-AC rain water pipe shall be measured over all as fixed along the centre line over the fittings and accessories)

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new PVC clamps complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new PVC clamps complete all as specified and directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal with access door with cement joint complete all as specified and directed.

S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal with access door with cement joint complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) reducers 75/110mm bore complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection finished fair & even laid in alternative bays not exc 2M in length and joints filled with bitumen mastic 1:3 complete all as specified and directed.

M&L for cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in filling foundation and mass concrete, complete all as specified and directed.

S&F in repair of stainless steel kitchen plate rack of overall size 750 mm x 600 mm x250 mm, with partitions for small and large plates etc made out of stainless steel 0.63 mm thick fixed with rawl plugs and CP steel screws complete all as specified and directed

S&F in repair new rigid PVC waste pipe of approved quality 32mm bore, 75mm long with one end socketed fixed to waste coupling including one PVC reducer 32mm complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description over 10CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10CM width or girth and applying one coats of synthetic enamel paint over a coat or red oxide primer complete all as specified and directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description not otherwise descriped over 10cm width girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted wooden surfaces and applying one coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer, complete all as specified and directed.

M&L for complete removal of existing treatment of surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/ tint, complete all as specified and directed.

M&L for preparation of new surface of wall and applying two coats of wall care putty on walls overall thickness 3mm and finished surface even and smooth, complete all as specified and directed.

M&L for complete removal of existing treatment of surfaces of wall and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint complete all as specified and directed.

M&L for complete removal of existing treatment of wall & applying two coats of cement base paint of approved shade/tint complete all as specified and directed.

Complete removal of existing treatment on wall / roof projection including facia cornies etc by scrapping with mechanical sender (having mecahnical vaccum mechanism) with sanding pad of appropriate grit to make surface clean free from dust loose paint etc by skilled labour and M&L for two coats of 100% remium acrylic emulsion paint having VOC less than 500 gm / litre and UV resistance as per IS 15489 : 2004 alkali & fungal resistance dirt exterior paint of required shade (company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat exterior primer applied @ 0.90 litre /10 sqm over a coat of 1mm thik wall care putty complete all as specified and directed. (Note - Primer and emulsion to be carried out through air less spray machine (Mechanical means)

S&F in repair cast copper alloy health faucet chromium plated with 1.00 Mtr long flexible tube including wall hook complete all as specified and directed.

M&L for preparation of old/ newly plastered surfaces of ceiling and applying two coat of white wash on ceiling complete all as specified and directed.

M&L for preparation of old/ newly plastered surfaces of wall and applying two coat of white wash on wall complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash on wall complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of ceilling and applying one coat of white washing on ceilling complete all as specified and directed.

M&L for preparation of old previously treated surfaces of walls and applying one coat of white wash on walls complete all as specified and directed.

S&F in repair 15 mm dia stop valves, cast copper alloy, chromimum plated, with long shank and cup concealed type complete all as specified and directed.

S&F in repair 15mm dia two way bib taps, cast copper alloy chromium plated fancy type handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

M&L for PCC 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in roof padding/ roof kerbs / benching / coved fillets etc rounded or chamfered on edges, complete all as specified and directed

Jointing only for 100mm bore cast iron pipes and fittings to PVC pipes in repair with epoxy based polymer and making joints leakage proof all complete all as specified and directed

S&F in repair 32mm bore brass chromium plated bottle trap for wash basin with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed.

M&L for welding in repair exc 2.5 cm but not exc 5 cm in length thickness of metal to be welded not exc 6 mm complete all as specifed and directed.

Excavating in trenches not exc 1.5 m wide and not exc 1.5 m in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each not exc 0.5 cum, getting out, and removing surplus soil to a distance not exc 50m and making good surface in soft/loose soil, complete all as specified and directed.

M&L for hard core broken bricks of gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15cm thick, water and rammed to a true surface complete all as specified and directed.

M&L for cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundations filling, sub base and mass concrete filling, etc complete all as specified and directed

M&L for earth filling under floor spreading and levelling in layers not exc 25 cm thick for well ramming watering required complete all as specified and directed .

M&L for RCC type B-1 (1:2:4) (using 20mm graded stone aggregate) as in slab supported on wall walls beams and columns in floors roof landings complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base of floor complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over for reinforcement cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, and binding with and incl MS wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-415 or Fe-500 complete all as specified and directed.

M&L form work for flat fair finished surfaces of concrete to soffits of suspended slabs such as roof slab not exc 200mm thick complete all as specified and directed.

Removing excavated materials not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layer not exc. 25 thick complete all as specified and directed.

S&F roof trusses (framed) trussed purlins, crane gantries, rails and fastening and heavy brackets framing (Beam, tee, angle, channel or flat section) including distance pipe, cleats conforming to Fe-290 (Gde 165-E) etc complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws all including fixing bracket suitable for galvalume sheet profile complete all as specified and directed.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc for taking credit including making good the disturbed surfaces to match with the existing complete all as specified and directed.

Material and labour for one light / fan point controlled by one, one way switch 06 Amp wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60 mm thick with 3 mm thick plastic laminated sheet top cover, brass screws, cup washers etc and making good to the disturbed surfaces to match the existing complete all as specified and directed.

All as per serial item No 136 here-in-before but one 3 pin, 06 Amp socket outlet point on independent board controlled by one, one way switch 06 Amp.

All as per serial item No 136 here-in-before but one 3 pin, 06 Amp socket outlet point on same board controlled by one, one way switch 06 Amp.

All as per Serial Item No 136 here-in-before but point wiring with 2.5 sqmm single core FRLS cables and earth continuity wire of 1.5 Sq mm single core FRLS cable for one 3 pin 16 Amp socket out let point controlled by one, one way switch on independent board complete all as specified and directed.

Supply and fix switch piano flush type, 06 Amp, single pole, one way, 230 Volt complete all as specified & directed.

Supply and fix bell push, flush type, 06 Amp, 230 volt complete all as specified and directed

Supply and fix socket outlet 2 in 1, 5 pin, 06 Amp, flush type, 230 volt complete all as specified & directed.

Supply and fix switch socket combination outlet 2 in 1, 3 pin, 06 Amp and 16 Amp flush type, universal, 230 volt, four hole complete all as specified & directed.

Supply only LED bulb 9/10 Watts suitable for B22 white in colour complete all as specified and directed

Supply and fix lamp holder, PVC / Polycarbonate type with back plate suitable for batten fitting complete all as specified & directed.

Supply and fix in replacement of single side connection LED T8 tube light rod 20 Watt, 6500K of four feet long into and including LED tube light fixture of four feet long with T8 push fit type holders, connector block, end caps, etc including connecting up complete all as specified and directed. Make : Crompton, Cat No : IGP131LT8-16& LT8-20-865-2 or Havells, Cat No : REGALBATTENT8UPT01X22WSSBS & PHOTONULTRA1213T8SSTL20WLED865SPC,Philips cat no TMC 501P1XT-LED22W P 3241

Supply and fix in replacement LED tube light fittings 10 Watt, 6500K of two feet long energy effcient etc including connecting up complete all as specified and directed.Make : Crompton, Cat No : DMLN1LT8-8& LT8-8-865-2 or equivalent in havells / Philips as approved by GE

Supply and fix ceiling rose, 6 Amp, 250 volt, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25 mm size complete all as specified & directed.

Taking down carefully exhaust fan of any sweep complete with all accessories, dismantling blades and deposit in safe custody for refixing at same location after repair procedure complete all as specified & directed.

S&F exhaust fans, plastic body, AC, single phase, 230/240 volt of size 200 mm sweep with louver and making connection with twisted copper flexible wire 23/0.076mm complete all as specified and directed

Material and labour for sub main wiring with 04 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

Supply and fix in replacement of industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volt of 20 Amp, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed. Make: - Legrand, Cat No. 5078 11 & 4085 93 or equivalent in Hager, Cat No : VYA120C & NCN120N or Schneider, Cat No : A9HMS220 & A9N1P20C

M/s Bhadoria Associates

ANIL CONSTRUCTION

M/S AADI ENTERPRISES

QUALITY CONSTRUCTIONS CO

M/s Durga Construction Company

m/s raghubar dayal

M/S SHIVA CONSTRUCTION

M/s Ramesh Chandra

Rakesh Traders