Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹39.2 LAccepted-AOC D 89 SHASTRI NAGAR MEERUT UP 250004 | MEERUT | UTTAR PRADESH | 250004 | ₹39.2 L Quoted ₹39.8 L | L1 | Accepted-AOC Tender Accepted due to being L1 |
| 2 | L2₹43.6 LRejected-Finance 0 0 NAGLA MALOO MOHAMMDABAD FARRUKHABAD FARRUKHABAD FARRUKHABAD UTTAR PRADESH 209625 | FARRUKHABAD | UTTAR PRADESH | 209625 | ₹43.6 L | L2 | Rejected-Finance Rejected due to not being L1 |
| Sl No | Description | Qty | Unit | mohanlal gupta L1 | V S ENTERPRISES L2 |
|---|---|---|---|---|---|
| 1.00 | Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed. | 16 | Sqm | 50 ₹800 | 111 ₹1,776 |
| 2.00 | Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5mtr depth and getting out in any type soil complete all as specified and directed. | 16.91 | Cum | 200 ₹3,382 | 175 ₹2,959.25 |
| 3.00 | Returning filling in,including spreading,levelling,watering and well ramming in layers not exceeding 25cm in soil complete all as specified and directed. | 7.42 | Cum | 100 ₹742 | 120 ₹890.40 |
| 4.00 | Removing excavated soil not exceeding 50mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed. | 10.49 | Cum | 100 ₹1,049 | 120 ₹1,258.80 |
| 5.00 | M & L for broken bricks Hardcore of guage not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed. | 2.4 | Cum | 800 ₹1,920 | 1,400 ₹3,360 |
| 6.00 | M&L for PCC 1:4:8 type D-2 (40 mm gradded) as in foundation filling and mass concrete complete all as specified and directed. | 19.53 | Cum | 4,000 ₹78,120 | 4,200 ₹82,026 |
| 7.00 | Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed. | 6 | Sqm | 80 ₹480 | 100 ₹600 |
| 8.00 | Treating the backfill in contact with foundation @ 7.5 litres of emulsion / Sqm of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified and directed. | 6 | Sqm | 80 ₹480 | 100 ₹600 |
| 9.00 | Treating the top surface of filled earth @ 5 litres of emulsion / Sqm of surface complete all as specified and directed. | 5.76 | Sqm | 80 ₹460.80 | 100 ₹576 |
| 10.00 | Treating the soil under plinth protection @ 5 litres of emulsion / Sqm of surface area complete all as specified and directed. | 12 | Sqm | 80 ₹960 | 100 ₹1,200 |
Updated dates
Tender Value
₹44.5 L
EMD Value
₹89,900
Closing Date
8 Dec 2025, 6:00 pmClosed
Garrison Engineer (South) Meerut Cantt
Garrison Engineer (South) Meerut Cantt The Mall Road Meerut Cantt Distt Meerut-250001(UP)
SPL REPAIR TO BLDG NO E-142 WITH OTM ACCN, 509 ASC BN AND ADDN/ATLN OF TOILET BLOCK AT BLDG NO 182 OF 32 INF BDE CAMP UNDER AGE B/R-IV AND AGE E/M-II OF GE (SOUTH) MEERUT CANTT
2025_MES_733155_2
GE/MRT/S/8254/2025-2026
Open Tender
Civil Works
180 days
Meerut Cantt
Please refer Tender documents.
10 documents required · 10 mandatory
₹500
GE (South) Meerut
₹89,900
Yes
Garrison Engineer (South) Meerut Cantt
3 Mar 2026
12 Nov 2025
10 Dec 2025
12 Nov 2025
8 Dec 2025
19 Nov 2025
14 Nov 2025
Amount
Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.
Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5mtr depth and getting out in any type soil complete all as specified and directed.
Returning filling in,including spreading,levelling,watering and well ramming in layers not exceeding 25cm in soil complete all as specified and directed.
Removing excavated soil not exceeding 50mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.
M & L for broken bricks Hardcore of guage not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.
M&L for PCC 1:4:8 type D-2 (40 mm gradded) as in foundation filling and mass concrete complete all as specified and directed.
Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.
Treating the backfill in contact with foundation @ 7.5 litres of emulsion / Sqm of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified and directed.
Treating the top surface of filled earth @ 5 litres of emulsion / Sqm of surface complete all as specified and directed.
Treating the soil under plinth protection @ 5 litres of emulsion / Sqm of surface area complete all as specified and directed.
M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.
All as per item No 11.00 here-in-before but except bricks.
M&L Brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed.
M&L for rendering 15 mm thick on brick or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed.
M&L rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling complete all as specified and directed.
M&L for rendering 15 mm thick on brick surfaces or surface other than fair face of brick work or on one side of lathing in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.
M&L PCC (1:4:8) type D-2, 75 mm thick (using 40 mm graded stone agg) as sub base complete all as specified complete all as specified and directed.
M&L Non-skid coloured ceramic tiles 7 to 8mm tk (Square/Rectangular) area of each tiles exc 0.11 Sqm but n exc 0.18 Sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match including over 15 mm thick screed bed or bedding layers in CM (1:6) for laying in floors finishing complete all as specified and directed.
M&L Coloured Glazed ceramic tiles in vertical surfaces 350x250mmx7mm / 450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10mm thick plaster in CM(1:4) complete all as specified and directed.
M&L TMT bars 10mm dia and over cut to length bend to shape reqd incl cranking, bending and binding with MS wire (annealed) not less than 0.90mm dia complete all as specified and directed.
All as item No 20.00 here-in-before but 6 to 8 mm dia
M&L for RCC (nominal mix) 1:2:4 type B-1 (using 20mm grade aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc. Complete all as specified and directed.
M&L RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.
M&L RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded aggregate in Columns, pillars, piers, posts and struts complete all as specified and directed.
M&L RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.
Use and waste of formwork to sides of concrete foundation, footings, bases of column, rafts, plinth beams and similar work vertical or to batter rough finished surface flat of concrete, With water tight complete all as specified and directed.
Use and waste of formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat complete all as specified and directed.
Use and waste of formwork to sides of pillars, posts, struts, piers,columns, and stanchions Rough finished surfaces of concrete Circular on plan complete all as specified and directed.
Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; n exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat complete all as specified and directed.
M&L for formwork to Edges of concrete flats, treads, breaks in floors.concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC band in walls, sloping and similar work for fair finished surfaces. Rough finished surfaces of concrete flat complete all as specified and directed.
S&F PVC (SWR) pipes 110 mm single socketed, in any length with solvent cement joints fixed to walls/laid in floors incl stack clamps of 50mm x 3 mm flat iron with bolts & nuts complete all as specified and directed.
M&L PVC SWR floor trap, with grating including joining to waste pipe fixed in cement concrete type B-1 (1:2:4) 100 mm dia complete all as specified and directed.
M&L PVC (SWR) multifloor trap 100 mm dia with grating including jointing with solvent cement complete all as specified and directed.
M&L PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement complete all as specified and directed.
S&F PVC (SWR) 110mm bore pipes single socketed in any length witlh rubber ring joints laid in trenclhes or in floors complete all as specified and directed.
S&F PVC (SWR) 75mm bore pipes single socketed in anoy length witlh rubber ring joints laid in trenclhes or in floors complete all as specified and directed.
S&F PVC (SWR) bend 110mm dia radius complete all as specified and directed.
S&F PVC (SWR) bend 75mm dia radius complete all as specified and directed.
Supply & fix in repair vitrous china wash down water closet pan ( padestal pattern), white (excluding fixing bolts, flushing cistern). Including white plastic seat cover for WC ( E.T ) white including MS CP or aluminium hinging device complete all as specified and directed.
S&F in repair vitreous china wash hand basin white flat back size 550x400mm excluding taps, waste but incluing brackets, CP waste couping, PVC Waste pipe 32mm dia etc complete all as specified and directed .
S&F in repair 10 litre capacity PVC valveless, Syphonic action type, flushing cistern low level,white with inlet ball valve, float and handle including brackets and PVC flush pipe etc complete all as specified and directed.
S&F in repair fancy type center hole mixer CP Brass Mixer for mixing hot and cold water screwed down for iron pipe complete all as specified and directed.
S&F Brass CP bottle traps 32mm bore for wash basins with inlet & outlet screwed for pipe or connections including necessary packing, union & cap
S&F PVC Connection 15 x450mm size with PTMT Nuts at both ends with rubber washers complete all as specified and directed.
S&F in repair Fancy type Corner Glass shelf 5.5mm thick glass with CP Railling complete all as specified and directed.
S&F Fancy type CP Brass tubular Towel rail 20 mm dia & 600mm long complete all as specified and directed.
S&F Fancy type CP brass soap dish complete all as specified and directed.
S&F 15mm bore fancy type CP Bib tap (long body) cast copper alloy with capstan head screw down for iron pipe or for brass furrel complete all as specified and directed.
S&F 15mm bore fancy type CP brass angle Valve, complete all as specified and directed.
S&F 15mm bore fancy type CP brass consealed stop cock, complete all as specified and directed.
S&F Bib taps two way 15 mm bore , cast copper alloy choromium plated with crutch or butter fly handle screwed down screwed for iron pipe or brass ferrule complete all as specified and directed.
S&F Rotational moulded polythylene 500 capacity water storage tank(Cylindrical vertical with closed top) hoisted and fixed in position alongwith 20mm bore ball brass valve high pressure with polythene float and fly nut complete all as specified and directed.
S&F Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.
S&F Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.
S&F 15mm bore GI tubing medium grade with all fittings fixed to walls or laid in floors complete all as specified and directed.
S&F 20 mm bore GI tubing medium grade with all fittings fixed to walls or laid in floors complete all as specified and directed.
Solid PVC Door frame of size 50mm x 47mm made out of 5mm PVC sheet reinforced suitable for solid PVC door suppling & fixing in opening complete all as specified and directed.
S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, & joined together with solvent cement, in the frame at site as per specification & drawing in SSR.
S&F stainless hinges 100 mm size, medium weight, cold rolled complete all as specified and directed.
S&F Aluminium handles 125 mm size, cast type, anodised complete all as specified and directed.
S&F Aluminium, anodised, barrel tower bolts 150 mm long of extruded section complete all as specified and directed.
S&F Factory made steel ventilators fixed type with glazing bars complete all as specified and directed.
S&F Aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire stappler complete all as specified and directed.
S&F 3 mm thick sheet glass ordinary quality frosted on one side n.exe 0.5 sqm in each pane complete all as specified and directed.
S&F in repair 3mm thick, plain sheet glass ordinary quality and glazing with oil pane putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.
M&L Salt-glazed stoneware drain pipes laid in trenches & jointed as specfified of 150mm dia complete all as specified and directed.
M&L for PCC 1:3:6 type C2 concrete bed to drain pipes including packing under, and completely surrounding pipes after they are laid and tested; in for 150mm dia pipe of SGSW complete all as specified and directed.
S&F PVC vent Cowl 110 mm complete all as specified and directed.
Cutting into existing manholes for connecting new drains 150mm dia, making good to pipe & rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, & reforming benching as required complete all as specified and directed.
M&L for rendering over roof slab with CM 1:4, 20 mm thick mixed with water proofing compound, complete all as specified and directed. Note : WPC shall be measured & paid separetely.
M&L for applying oil based bitumen primer @ 0.30 Kg/Sqm, providing and laying 3 mm thick APP modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with one woven polyester mat weighing not less 160g/Sqm having softening point not less than 140 degree centigrade longitudinal tensile strength not less than 650 N/5 cm, tearing strength of 180 N torch application including minimum 10 cm side over lap & 15 cm end overlap, (applying a coat of blown grade hot bitumen 85/25 over membrance @ 1.2 Kg/Sqm) and applying bituminous aluminium paint @ 200 gm/Sqm complete all as specified and directed.
Supply only liquid water proofing compound complete all as specified and directed.
M&L for preparation of newly plastered surface of wall etc and applying wall putty and two coat of oil bound distemper (OBD) over one coat of primer complete all as specified and directed.
M&L for preparation of newly plastered surface of wall etc and applying Birla white/JK cementitious wall care putty and after applying two coats of Cement base paint over a coat of alkali resistence primer in any colour complete all as specified and directed.
M&L applying three coats of white wash on new Ceiling surface including preparation of surface complete all as specified and directed.
M&L Providing cement concrete 75mm thick type C2 (1:3:6) (40mm grade aggregate) as in Plinth protection finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.
Supply & fix in repair vitreous china urinal half stall type with including providing & fixing of plugs bedding against wall in cement mortar 1:2 pointing around urinal back in cement mortar complete all as specified and directed.
S&F fancy type CP Brass wall mixer for mixing hot & cold water with telephonic Shower screwed down for iron pipe complete all as specified and directed.
S&F Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc incl powder coating (minimum thickness of powder coating 50 micron). Complete all as specified and directed.
S&F Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised alumnium snap beading, screws etc for powder coating of any colour (Thickness or powder coating not less than 50 micron). Complete all as specified and directed.
M&L Moorum/ red bajri filling in floors or pavings, laid in layers not exceeding 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.
M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cmenet mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to mat specified and directed by Engr-in-Charge
Material & labour for provision of GI frame work(snap grid) suitable for size as in false ceiling of size 605mmx605mm consisting of followings and all as directed:-i) Aluminium sections incorporated in frame work shall conform to designation 63400 given in IS: 737-1986. ii) The snap grid shall consist of aluminium anodized main /cross tee of size 36.5mmx25mmx1.4mm thick and 25mm x 25mm x1.4mm thick, respectively. iii) Snap grid frame shall be fixed to ceiling with and including supporting hangers consisting of 2mm to 4mm dia mild steel GI wire. iv) The main and cross tees shall be jointed at junction/crossings with aluminium anodized angle bracket, of size 15mmx15mmx1.5mm thick, fixed with suitable mild steel, bolts, nuts and washers all as per manufacturer’s instructions. v) The snap grid (main/cross tee section) shall be supported at ends all along the wall with aluminium anodized angle of size 25mmx25mmx1.4 m anodized m thick. vi) Size of the snap grid shall be 605mm by 605mm. vii) Minimum average thickness of anodizing shall be 50 micron complete all as specified and directed.
S&F 4 mm mm thick gypsum board with aluminium coating on back side in ceiling size 60cm x 60cm fixed to aluminium snap gird complete as per manufcturer"s instructions complete all as specified and directed.
Taking down wooden chowkhats or frame not exceeding 1.5 Sqm each with shutters (without taking off shutters from the frame), complete all as specified and directed.
Taking down Chowkats or frames exceeding 1.5 sqm but not exceeding 4 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.
Dismantling, floor, hearth or wall tiling including cement mortar bedding but not backing and removing rubbish off the premises complete all as specified and directed.
Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified and directed.
Construction of Soakage well, excavation in ordinary soil, foundation PCC 1:3:6 wells of honey combed and solid in M-25 concrete, including intercepting chamber screen chamber Brick work CM 1:4, RCC cover slab in M-25/RR masonery/ Filling with brick bats, complete of size 1.80 m dia x 3.0 m deep, complete all as shown in drg No - TD 309 Sheet No 1/4 to 4/4 and as directed by Engr-in-Charge.
M&L Cement concrete 1:3:6 type C-2 40mm aggregate as in foundation manholes complete all as specified and directed.
M&L for Cement concrete 1:2:4 type B-1 (20mm graded) as in coping to manholes complete all as specified and directed.
M&L for precast cement concrete 1:2:4 type B-1 (20mm graded agg) as in manhole covers slabs set in cement mortar 1:4 complete all as specified and directed.
M&L Rendering 10mm thick on fair face on brick work or conc surfaces finished even and smooth without using extra cement in CM 1:4 complete all as specified and directed.
M&L Cement concrete 1:4:8 type D-2 bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150mm bore pipes complete all as specified and directed.
S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.
S&f 2nd class hard wood, 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.
S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified and directed.
S&F Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.
S&F in 25 mm bore drapery curtain rods powder coated finished as directed with fancy type incl fixing brackets, stops, rollers etc complete all as specified and directed.
Demolition of PCC in ground floors & pavings not exceeding 15 cm thickness (below or above ground level) (unreinforced) complete all as specified and directed.
M&L for 25 mm thick PCC 1:2:4 type B-0 (12.5mm graded aggregate) as in sub base floor etc complete all as specified and directed.
S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed in CM(1:6) complete all as specified and directed.
All as item No 103.00 here-in-before but herein over and including 10mm thick rendering in CM 1:4, as in skirting/dado complete all as specified and directed.
M&L PCC 1:3:6 type C1 (using 20 mm graded aggregate) as in bed block, copings, kneelers, apex stones, bed plates, water troughs and the like including cutting into bricks of stone wall as reqd for inserting hold fasts complete all as specified and directed.
M&L 75 mm thick PCC 1:3:6 type C1 (20 mm graded stone aggs) as in plinth protection, path including finished surfaces even and smooth without using extra cement complete all as specified and directed.
Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards / slabs / blankets, any thickness, including cover fillets complete all as specified and directed.
Supply and fix false ceiling with 4mm thick E board white prelaminated, set embossed reinforced designer ceiling board of oceanic texture fixed over and including GI grid frame work of size not more than 600x600 mm having 25mm wide t-section runner made of 0.33mm GI sheet and angle made 0.45mm thick GI sheet suspended with and including 4mm dia GI wire and leveling clips complete all as specified and directed. Note: All exposed surface of grid shall be powdered coated white.
Taking down cement plaster from brick walls or concrete surfaces including raking out joints, hacking out for key, scrubbing down with water complete all as specified and directed and removing rubbish etc. complete all as specified and directed.
Dismantling of Asbestos cement / Fiber (corrugated, semicorrugated, etc.) sheet any description as in roof covering incl ridge and removing from site complete all as specified and directed.
M&L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding / ridges, fixed with self tapping screws complete all as specified and specified.
S & F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed.
S&F MS flat iron as in wind ties for roof cutting tops to shape as directed, drilling holes flat iron fillets including all necessary drilling, bolting or riveting, etc & similar work conforming to Fe 290-0 Gde E-165 complete all as specified and directed.
Supply & fix in repairs second class hardwood (SAL) as in plain solid straight chowkats or frames, wrought, rafter, purlins and like truss work etc framed together with glue pinned at joints, with single or double rebates or as in perlins, rafters etc complete all as specified and directed.
M&L for complete removal of existing treatment and finishing of wall surface by using wall care putty and applying two coats of oil bound distemper (OBD) over a coat of primer in any colour complete all as specified and directed.
M&L for preparation of new or previously untreated wooden surface of any description, not otherwise described over 10 cm width or girth and apply two coat of synthetic enamel paint over over a coat of pink primer complete all as specified and directed.
M&L for preparation of new or previously untreated steel & iron surfaces of any description, not otherwise described over 10 cm width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.
M&L 75 mm thick cement concrete 1:3:6 type C-2 using (40 mm graded stone agg) as in sub base complete all as specified and directed.
M&L for laying 60 mm thick machine pressed precast PCC coloured interlocking paver block moulded in PVC frame / mould any shape and size conforming to IS 15658-2006 of M-35 grade of approved design with gray cement and pigment to match shade / colour / matrix of tiles set and bedded over 25mm thick fine river washed sand duly compacted with surface vibrator laid over compacted sub soil in flooring complete all as specified and directed. Note :- Sand cushioning shall be measured and paid separetely.
M&L Sand for cushioning, interlocking tiles joint to be filled with sand, including spreading and levelling in layers not exceeding 25 mm thick complete all as specified and directed.
S&F rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc including notching, drilling, fittings, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing fittings angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing conf to Fe-410-w (Gde-E -250) quality A complete all as specified and directed.
S&F Steel windows box type using 'P' section comprising double frame for gauge and glazed skelton shutter jointly with flat iron 40x3mm complete including hinges, handle, tower bolts, stops, lugs etc of suitable size as decided by Engineer-in-Charge. Note (i) For the purpose of measurement & payment double shutter with frame shall be considered as one unit (ii) Unit rate quoted against this item shall also include the iron mongreries shown on drgs (iii) gaurd bars glazing & Wire mesh shall be measured and paid for separately complete all as specified and directed.
S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors and frames/ chowkats; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe-410 or Fe-310 complete all as specified and directed.
Taking down carefully any type of battens or conduit point wiring with or except conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, pendent light fittings, MCBs / isolators, fan regulators, tube light fittings etc removing material from site complete all as specified and directed.
Material & labour for point wiring with FRLS PVC insulated 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, stranded, unsheathed copper conductor cable in and including PVC concealed conduit of size 20mm dia or higher, medium grade complete with and including all PVC conduit accessories / fittings, brass screws, washers etc, sunk zinc coated pressed steel terminal boxes including all cutting / chases etc in walls, with 3mm thick plastic laminated sheet cover including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed for one Tube light/bulb/street light point controlled by one, one way switch 05 / 06 Amps.
All as item No 125.00 here-in-before but One ceiling fan/exhaust fan point controlled by one, one way switch 05 / 06 Amps.
All as item No 125.00 here-in-before but One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch.
All as item No 125.00 here-in-before but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 5 /6 Amps socket outlet point on independent board.
All as item No 125.00 here-in-before but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15 / 16 Amps socket outlet point on independent board.
Supply & fixing switch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified and directed.
Supply & fixing socket outlet 3 pin, 05 / 06 Amps flush type 240 volts complete all as specified and directed.
Supply & fixing switch piano flush type, 15 / 16 Amps single pole, one way 240 volts complete all as specified and directed.
Supply & fixing of socket outlet 3 pin 15 / 16 Amps (2 in 1 Multipurpose) 240 volts complete all as specified and directed.
Supply and fix decorative LED Batten 20 Watt polycarbonate housing integtrated type complete with all accessories and fixing material complete all as specified and directed.
Supply and fixing lamp holder , PVC / polycarbonate type back plate suitable for batten fitting complete with 1 x LED lamp 10 watt. Complete all as specified and directed.
Supply and fix decorative LED Batten 10 Watt polycarbonate housing integtrated type complete with all accessories and fixing material complete all as specified and directed.
Supply & fixing of ceiling rose, 3 terminal PVC polycarbonate isolated body complete all as specified and directed.
Material and labour for sub main wiring with 06 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor FRLS- FLEXIBLE WIRING CABLE. CONFORMING TO IS: 694-1990 with and including continuous earth wire of size 6.0 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all MS conduit accessories / fittings, brass screws, washers etc and connected to common earth dolly including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as specified & directed. Note:- One meter of conduit along with 2x6 sq mm wire and one 6.0 sq mm earth shall be measured as one unit length.
Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 4 way, with 200 Amps rated complete all as specified and directed.
Supply and fixing MCB SP, AC, 240 volts of 06 to 40 Amps, C curve, 10 kA, complete all as specified and directed.
Supply and fixing exhaust fan steel body AC single phase 230 V of size 380mm sweep with blade , frame and lauvers complete all as specified and directed.
Supply & fixing industrial type SPN enclosure with a two pin and earth plug and socket complete with and including 32 Amps MCB, single pole, AC, 240 volts complete all as specified and directed.
Supply and fixing LED building security light fitting 1x35 Watt luminaries with die cast aluminium housing comprising epoxy poweder coated enclosed with glass cover in frame with high power LED white lamp of capacity 35 watt including making connections complete with bracket fitting made out of GI pipe medium grade including clampsand nuts and bolts complete all as specified and directed.
Supply and fixing of decorative LED Tube light fitting 1x20 Watt , environmental friendly, energy efficient MS batten with retrofit T8 polycarbonate LED tube-01 No, with batten and all accessories complete all as specified and directed.
Supply and fixing sheet metal enclosure, Triple pole and neutral AC, 415 volts, 04 way, with 200 Amps rated copper bus bar and IP - 43 & IK 09 protection including provision for four pole isolator/mcb as incomer with metal double door and flush to wall including all cutting etc complete all as specified and directed.
Supply and fixing Isolator 4 pole 'B' series 100 amps capacity AC 415 V,10kA complete all as specified and directed .
Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8way, with 200 Amps rated complete all as specified and directed.
Supply & fixing MCB SPN, AC, 240 volts of 32 to 63 Amps, C curve, 10 kA, complete all as specified and directed.
Supply, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 16 Sqmm 2.0 core armoured, PVC sheathed with aluminium conductor heavy duty complete all as specified and directed.
Supply / laying and fixing 40mm bore galvanised steel tubes with all fittings, light grade, laid in trenches for cable protection complete all as specified and directed.
M&L for washed river dry sand cushioning in trenches 80mm thick before laying the cable and 150mm thick after laying the cable including spreading levelling and hard punning complete all as specified and directed.
Material and labour for contineous brick edging with width equal to the depth of the brick of whole sub class 'B' bricks laid on edge complete all as specified and directed.
Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.5 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed.
Taking down Ceiling fan and hook, ceiling cable end , dismantling blades and removing fans and blade to stores for safe costudy complete all as specified and directed.
Supply and fixing new ceiling fans complete with blades, down rods, electronic regulator and ccessories, 230 V, 1200 mm sweep. Min air delivery 245 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.
M&L for Ceiling fan hook made from steel structural, bracing support bend into shape for hanging of ceiling fan complete all as directed at site.
Supply and fix desert cooler electric driven single phase 230 Volt metallic body (GI) , thickness not less than 1.5mm capacity of water not less than 70 Ltr , 1440 RPM with copper winding and power consumption not more than 240 watt, 50 Hz complete all as specified and directed.
V S ENTERPRISES (BID ID -3488597)
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 3.81 MB
BOQ_827955.xls
BOQ • 0.59 MB
TenderdocumentsBR-EM.pdf
Tender Documents • 2.09 MB
Download all tender documents and submit your bid