ROOF TREATMENT AND REPAIRS TO LEAKAGE/ SEEPAGE FOR OFFRS LIVING ACCN IN SW ZONE AT RMS

Amount

Roughening surfaces of old concrete floor/terrace by picking incl. taking down existing detoriated / decayed tar felt or any treatment including loose surface, scraping with scraper, chiseling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 50 m.

M&L for 15 mm thick screed bed or bedding layer in CM 1:4 mixed with water proofing compound @ 3 % by weight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed.

M&L for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following -

Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.25 kg/Sqm on top of dry surface of finished cement mortar plaster.

One layer of APP based polymeric water proofing membrane of weight not less than 3.5 kg/Sqm consisting 3mm thick reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm) shall be applied over bituminious primer . Application of APP membrane over primer shall be done by torch application.The overlap shall be minimum 100 mm on the traverse direction and 75 mm on longitudinal direction and the over lap shall be sealed by flame.

Applying two coats of aluminum paint on top of membrane @ 0.11Kg/Sqm.

M&L Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m on roof surfaces.The work will be carried out upto triple storey building & the rate for scaffolding is included in this item also.

M&L Pressure grouting of honey combed concrete with cement slurry by adding CEBEX 100 or equivalent @ 255 gms/50 Kg of cement.

M&L for PCC 1:5:10 type E-2 using 40 mm graded brick aggregate as in filling of sunken portion etc complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B0 using 12.5 mm graded crushed stone aggregate mixed with WPC (in proportion as per manufacturer's instruction) as in bedding in sunken portion of slab complete all as specified and directed.

M&L for rendering 10mm thick plaster in cement mortar (1:3) mixed with water proofing admixture (in proportion as per manufacturers instructiion) as in sunken portion, finished the surfaces even and smooth without using extra cement complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings.

S & F Pre-painted galvalume aluminum zinc coating GI vased corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

S & F Pre-painted galvalume aluminum zinc coating GI vased Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

M&L 0.63 mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275.

M&L 0.63 mm Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275

Dismantling of plain or corrugated AC Sheets in roof coverings.

M&L 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc fixed with L or J type or cranked hooks.

M&L Asbestos cement one piece plain angular ridge 6mm thick

Dismantling mild steel or wrought iron work of any description not otherwise provided for.

S&F Rolled sections as in roof truss, purlins including cleats GDE Fe 410-0-or Fe 310-0.

Dismantling wall and ceiling boards (fibre pulp insulation etc) or insulation boards, slabs, blankets any thickness, incl cover fillets

Dismantling boarding any description fixed in any position with nails

S&F 4 mm thick 600x600mm size HSPC(High Pressure Steam Cured) prepainted, textured designer board , E Board classic to be fixed on GI grid/section size 600x600mm with main runner 38x24x0.9 mm thick,cross tee 28.6x24x0.9 and wall angle 19x19x0.9mm duly suspended with hanger any size ,comprising of 4 mm dia MS wire J type hook, nuts and bolt holding down clips complete all as specified and directed

S&F asbestos cement plain building boards, 4mm thick, fixed to timber framework with screws ,complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness below or above ground level

Dismantaling floor,hearth or wall tiling including cement mortar bedding (but not backing),removing serviceable tiles to store and rubbbish off the premises.

S&F light shade vitrified ceramic tiles 10mm thick n.exc 0.36 Sqm each in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 all as directed .all as specified and directed.

M&L for non skid coloured joint free tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 all as directed .

M&L for coloured Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 all as directed .

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300mm x 200mm, 7mm thick over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed.

M&L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed.set and jointed in neat cement slurry and pointed in white or colour cement to match

M&L 75 mm thick cement concrete type C2 1:3:6 (40 mm graded aggregate) as in plinth protection, using extra cement for finishing.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for.

M&L cement concrete type C2 1:3:6 (40 mm graded agg) as in surface channels and drains

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement incl firms moulds

Demolition of brick work built in cement mortar incl all quions, arches pillars etc but excl ashalar facing

M&L brick work with sub class B bricks straight or curved on plan exc 6 m mean radius in CM 1:6

M&L brick work with sub class B bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in cills, copings, benching on chajjas, roof kerbs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and directed.

Taking down chowkhat or frame not exc 1.5 sqm each (with out taking off shutters from the frame)

Taking down chowkhat or frame exc 1.5 sqm not exc 4 sqm each (without taking off shutters from the frame)

Taking down shutters only area n. exc 1 Sqm each.

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each

Taking down & refixing shutters of any description n exc 1 Sqm each in same opening

Taking down & refixing shutters of any description exc 1 Sqm and n exc 2 sqm each in same opening

M&L 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pined joints

M&L 2 nd class hard wood plain fillets. square, rectangular or triangular in section, clean sawn, se-cured with nails or brads exc 3 and n exc 6 sqcm

M & L 25mm thick second class hard wood boarding , plained one side with butt joints as in eaves boards .

M & L for block boards, 18/19 mm thick, grade 2 quality, interior grade , commercial type fixed with screws to timber frame work , for cup board including lipping / beading as required complete all as specified and directed.

S & F 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, for cup board including lipping / beading as required complete all as specified and directed.

S&F 40 mm dia, cupboard knobs fixed with nut , screw and washer of brass, polished complete all as directed

S & F 125 mm bright finished brass hasp and staple , safety type with mild steel hinge pin including bolt to hinge plate and fixed with screw.complete all as specified and directed

S&F 30mm thick continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed.

S&F 30 mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and directed

M&L 35 mm thick 2nd class HW plain framed pannelled shutter (any number of panels) with panels of timber flat on both sides or of veneered particle board medium density , wood particle board with commercial face veneers , supplied and fitted to chowkats.

M/L 35mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a) complete all as specified.

M/L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified.

M/L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated without sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing

S&F steel windows or ventilators, fixed type, with glazing bars.

S&F mild steel framed work as in grill, grating etc with end of bars shouldered and /or riveted or tonged into spikes, frame guard bars barrel iron doors, ladders, frame balusters, walk ways, railing. frame work of water tanks and similar works confirming to Fe 410-0 or Fe 310-0 complete

S&F Powder coated of any colour (Thickness or powder coating not less than 50 micron) Anodised aluminium frame for doors, windows and ventilators with one or more rebates including joining cleat for fixing etc

S&F Powder coated of any colour (Thickness or powder coating not less than 50 micron) Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 Kg/m including necessary joining cleats , glazing clips, rubber packing, anodised aluminium snap beading, screws etccomplete all as specified.

Taking down aluminium door shutter of any thickness and size and refixing in same opening after reparing/replacing stile and rail any type and size refixing the aluminium mongary and panel glass/both side laminated partical board etc.

S&F Sheet glass ordinary quality 4.8 mm thick and glazing in aluminum door in squares exc 0.5 sqm each

S&F Sheet glass ordinary quality 4.00 mm thick and glazing in aluminum window in squares n exc 0.5 sqm each

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S&F 4 levers brass mortices lock, vertical type, size 100mm

S&F Aluminium (Die cast) body , Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60kg and fixed

M&L for fixing 2 mm thick anodised aluminium composite panel fixed in aluminium frame including necessary rubber beading, jointing cleats all as specified and directed

M&L butt hinges medium grade cold rolled mild steel and fixed size of hinges 100 mm

S&F 100 mm size cadmium plated stainless steel butt hinges and fixed with stainless steel screws, complete all as specified and directed.

M&L butt hinges, medium weight 75 mm long size

S/F Aluminium anodised barrel tower bolt of extruded section and fixed 200 mm long

S&F Aluminium handle cast type anodised 150 mm long

S&F 125mm size aluminium handles,cast type,anodised all as directed complete all as specified and directed.

S/F Aluminium alloy anodised sliding door bolt with hasp and staple (bolt type fixing clips of sheet cast or extruded section (250 mm long)

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing fixing new ones.

M&L sheet glass ordinary quality 3mm thick and glazing with oil putty in squares n.exc. .5 sqm each pane complete all as specified and directed upto triple storey .Rate for scaffloding/ladder is included in this item.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples all as directed

S&F in repairs galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples all as directed by Engineer- in -Charge.

M&L in repairs GI wire netting 0.71 mm dia and 12 mm mesh lathing in to reed in walls incl all laps cutting and waste all as directed

S&F 0.71 mm thick plain aluminium sheeting , alloy 31000 H4 in ridges, hips , valley gutter , drip and straight flashing .

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, chajjas, fascias, fins and similar works.

M&L for reinforced cement concrete (nominal mix) 1:11/2 :3 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

S&F TMT MS bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia as specified .

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete.

S&F in repairs for Draperly rod /Harrison rails of stainless steel of 20mm dia with fixing brackets , stops, rollers and rings etc.

Easing of door/windows shutters for easy closing or opening leaf tightening of hinges or changing the position of hinges adjustment of tower bolt, sliding bolt etc complete all as directed.

Fixing of loose existing pelmet boxes made of 19mm thick block board by embedding wooden gutties in cement mortar (1:3) with MS clips and screws etc length of pelmet box not exc 1.50 mtr.complete all as diredted

All as per serial item No 90 here -in-before but length of pelmet box exc 1.50m and n.exc. 2.50mtr.

Repair to cupboard /Kitchen cabinets incl easing of cup board shutters tightening of piano hinges fixing of handle/knob hasp & staple etc (one unit self comprise of one CB irrepective of Nos of shutters).,complete all as directed.

M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer. -

M&L for preparation of new untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

M&L for preparation of old steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 20 mm bore GI tubing.

M&L cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10cm girth.

S&F tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid on floors etc, 15 mm bore.

S&F tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid on floors etc, 20 mm bore.

S&F CPVC 16 mm outer dia pipes SDR 11 & plain CPVC SDR fittings pipe line to walls & ceilings or laid in floors complete all as specified

S&F CPVC 20 mm outer dia pipes SDR 11 & plain CPVC SDR fittings pipe line to walls & ceilings or laid in floors complete all as specified

S&F CPVC 25 mm outer dia pipes SDR 11 & plain CPVC SDR fittings pipe line to walls & ceilings or laid in floors complete all as specified

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning the complete inner surface by rubber/nylon scraper to remove sludge/silt and washing with bleaching power solution and then clear water, etc. and hoisting in postion if required reconnecting and re-fixing in position.

Dismantling of CI pipes 100mm dia.

Same as in item No 105 above but 75mm dia of pipes.

S&F Cast iron 100mm bore Sand cast soil, waste & vent pipes, in any length with or without ears with cement joints, fixed to walls, up to triple storey high.The rates for use of scaffolding/ladder is included in this.

S&F Cast iron 100mm bore Bends (any radius), diminishing pieces or taper

S&F Cast iron 100mm bore Branch pieces, single (equal or unqual), ordinary or inverted (spigot or socket type) or with parallel branches and aceess door complete.

S&F Cast iron 100mm bore cowls

S&F Cast iron 75mm bore sand cast soil, waste & vent pipes, in any length with or without ears with cement joints, fixed to walls up to triple storey high.The rates for use of scaffolding/ladder is included in this item.

S&F Cast iron 75mm bore Bends (any radius), diminishing pieces or tapers

S&F Cast iron 75mm bore Branch pieces, double (equal or unqual), ordinary or inverted (spigot or socket type) or with parallel branches

S&F Cast iron 75mm bore cowls

M&L for sealing and grouting the mouth of pipes using Fosroc's non shrink grout Conbextra GP2 or equivalent For 110 mm dia

All as in item No 115 above but 75 mm dia

Taking down AC/Salt glazed ware pipes and fittings upto 110mm.

S&F in repair 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floor

S&F in repair 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls

S&F in repair 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floor

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall

S&F of 110mm dia PVC (SWR) bends

S&F 75mm PVC(SWR) bends any radius with access door.

S&F of 75 mm dia PVC (SWR) Vent cowl

S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

M&L 20 mm thick screed bed (bedding layer) in CM 1:4 , all as specified & directed

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite &

M&L for Granite (of any type) work (table rubbed and polished) 20 mm thick in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1;2) & including 15mm thick screed bed (bedding layer) in CM 1:4, all as specified & directed.

S&F in repair soap dish chromium plated stell/stainless steel, approx size 160x160mm x 1mm thick , fixed to walls with plugs & CP brass screws complete all as specified and directed.

Supply and fixed in repair vitreous china wash hand basin including brackets, white size 550 x 400 mm incl cutting cutting for and pinning in ends of brackets. Including Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed

S&F in repair 15 mm dia bib tap short body cast copper alloy(fency type), chromium plated ,'with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule all as directed.

S&F in repair 15 mm dia bib tap long body cast copper alloy(fency type), chromium plated ,'with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule all as directed.

S&F in repairs concealed stop valve, cast copper alloy, with crutch or butterfly handle, screwed down both ends for high pressure, as per ISI suitable for 15mm dia iron pipe all as directed.

S&F in repair fancy type pillar tap, cast copper alloy with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore.

S&F in repairs gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia all as directed.

S&F in repairs 125mm dia, chromium plated shower rose with or without swivel joints,including fixing to steelpipe or ounion of 15mm bore all as directed.

S&F in repair of PVC low level flushing cistern dual flush top push,10 Ltr capacity symphonic action type white as approved, ball valve float valve and handle, flush pipe incl CP bracket

S&F in repairs PVC connection 15mm size with PTMT nuts, of 450 mm length complete all as specified and directed.

S&F in repairs for 15mm dia of pipe Angle valves,fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed .

S&F grating doom 125mm dia with waste hole of PTMT (Min wt 40 gms).

S&F in repairs 600mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm longfixedwith two plugs (Gutties) of 2nd class hard woodembeded in cement mortar 1:3 with MS screwscomplete all as specified.

S&F in repairs CP Health Faucet with 1 mtr metalic Expandable tube & hook complete all as specified and directed.

S&F in repairs CP wall mixer (3 in 1) complete all as specified

S&F in repairs CP Central hole basin mixer fancy type 15mm dia all as specified and directed.

S&F in repairs vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed including 100mm CI 'P' trap.

S&F in repairs CP toilet paper holder all as specified.

S&F in repairs vitreous china water closet Padestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe and including EWC Sheet cover complete all as directed.

S&F in repairs fancy type looking mirror with bevelled edge of size 450x600x5mm thick

S & F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460 mm bowl size 410 mm x 330 mm x 160 mm

S&F in repairs Grating doom 100mm dia of PTMT (Minimum weight 25gms)

S&F in repairs peg set of Six chromium plated including fixing screw Make : Prayag

S&F magnet Catcher for cub board complete all as specified and directed.

S&F in repairs corner glass shelf assembly 250mm radius made of 6mm thick acrylic glass, with CP railing, fixed with suitable rowal plug & screws complete all as specified and directed.

All as per item No. 157 here in before but glass shelf assembly 300 mm radius.

S&F Sheet glass assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 600 mm long

S&F plastic water closet seat cover, black closed pattern with flat bottom and cover and MS chromium plated or aluminium hanging device ,fixed in repair, complete all as specified and directed.

S&F PVC waste pipe, 32mm bore, 750mm long for basin, fixed in repair, complete all as specified and directed.

S & F bottle trap 32 mm dia of PTMT having Min water seal of 25mm Min wt 260- gms complete all as specified and as directed.

S & F in repairs waste coupling of PTMT (half or full threaded) 32 mm dia ,complete all as specified and as directed.

S & F in repairs waste coupling of PTMT (half or full threaded) 40 mm dia ,complete all as specified and as directed.

Taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified

M&L 10 mm thick ceiling plaster in CM (1:3) on fair faces of concrete surfaces.

M & L rendering 15mm thick in cement mortar 1:4 mixed with water proofing compound @ 3% by wt of cement finished fair faces of brick/concrete surfaces even and fair without using extra cement . The work will be carried out upto tripple storey building the rate of scafolding is included for this item also. WPC will be measured and paid separately.

M&L rendering 10mm in CM 1:4 mixed with water proofing compound @ 3% by wt of cement on balcony, facia, roof projection and chajja etc. The work will be carried out upto tripple storey building the rate of scafolding is included for this item also. WPC will be measured and paid separately.

M & L rendering 15mm thick in cement mortar 1:6 on fair faces of brick or concrete work even and fair without using extra cement.

Supply only integral water proofing compound ( ISI marked )

M&L for three coats of white wash on newly plastered surfaces of walls including preparation of surfaces.

All as per item No 171 above but on ceilings .

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper of approved shade/tint over a coat of primer on walls all as specified & directed

All as per item No 173 above but on ceilings .

M&L preparation of newly plastered surface of any description and applying two coat of plastic emulsion paint over a coat of priming paint plaster coatcomplete all as specified and as directed.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint of approved shade on walls all as specified & directed by Engineer-in-Charge. The work will be carried out upto tripple storey building and the rate of scafolding is included for this item also.

M&L for prepration of newly plastered surfaces of walls and applying two coats of weather coat exterior emulsion over a coat of primer , complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls (plastered) by brooming down with steel wire brushing and applying one coat of white wash on wall complete all as specified & directed . White washing shall be carried out using DDL.The work will be carried out upto tripple storey building the rate of scafolding is included for this item also.

All as per item No. 178 above but on ceiling

M&L preparation old plastered surfaces of wall and applying one coat oil bound distemper on walls complete all as specified & directed.

All as per item No. 180 above but on ceiling

Preparation of old decorated plastered surface of any description and applying one coat of plastic emulsion paint complete all as specified and as directed.

M&L for preparation of old plastered or unplastered surfaces of external wall by brooming down with steel wire brushing and applying one coat of cement base paint on external wall surfaces complete all as specified & directed.The work will be carried out upto tripple storey building the rate of scafolding is included for this item also.

M&l for preparation old decorated surfaces on wall and applying one coat of weather exterior acrylic emulsion wall paint, complete all as specified and as directed.

Complete removal of exisitng treatment on walls all as specified and as directed.

All as per item No. 185 above but on ceiling

M&L for prepration of old decorated surfaces and applying two coats of white wash on walls, fins, facia. Chajja etc , complete all as specified and as directed.

All as per item No. 187 above but on ceiling

M/L for 2 mm thick Birla white putty/JK white wall care putty on walls.

M&L for preparation of old plastered surfaces of walls and applying two coats of distemper oil emulsion of approved tint all as specified .

All as per item No 190 above but on ceilings .

M&L preparation of old plastered surfaces of walls of any description and applying two coat of plastic emulsion paint complete all as specified and as directed.

M&L for preparation of old painted steel surfaces over 10 cm width/girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of old painted surfaces of wood over 10 cm width/girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of old painted steel surfaces not exc. 10 cm width/girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of old painted surfaces of wood not exc.10 cm width/girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of new steel surfaces of any description, n exc 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer.

Prepration of old painted surfaces of Brick, Stone, Concrete , Asbestos Cement or Plaster Surfaces and applying two coat of synthetic enamel paint all as specified and as directed.

All as per item No 198 above but on ceilings .

Prepration of old painted surfaces of Brick, Stone, Concrete , Asbestos Cement or Plaster Surfaces and applying one coat of synthetic enamel paint all as specified and as directed.

All as per item No 200 above but on ceilings .

Supply and fixing as in replacement stainless steel (conforming to AISI-304 grade) plate rack of overall size 750mm x 600mm x 254 mm or equivalent made of 1mm thick stainless steel sheet fixed on CP cantilever brackets, complete all as specified and as directed. Make : Jayna Cat No SBSD-05 or equivalent approved make.

VIHUTO YEPTHO

M/S ARVIND GROUP OF CONSTRUCTION & INFRASTRUCTURE

M/S Lucky Builders

sanjay kumar

commercial enterprises

M/S VIKASH TRADERS

MS SADHNA RAHUL