SPECIAL REPAIR TO BLDG NO P 243 AT PXE CHANDIPUR AND PROVN OF CERTAIN REVENUE AND MINOR WORK AT CHANDIPUR

Amount

NOTE (Applicable for all items) :- The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates. SCHEDULE 'A' PART-I (B/R PORTION)

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing ) and rubbish off the premises.

Dismantling stone slabs of any description laid, bedded and pointed in any mortar.

Demoltion of cement concrete (unreinforced) in floor and paving n exc 15cm thick (above or below GL) complete all as specified and directed

Demoltion of cement concrete (reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

M&L for 25 mm thick Cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in roof padding and in floor and to receive pavement tiles finished even and fair complete

M&L for 15 mm thick screed bed or bedding layer of mortar in CM 1:6 for laying floor finishes for vitrified tiles & heavy duty pre-polished tiles.

M&L for 10 mm thick rendering in CM1:3 as in skirting complete all as specified.

Virified Ceramic tiles 10 mm thick (square/ rectangular) light shade, polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces complete all as specified and as directed.

-Ditto- all as per item No 1.09 above but as in skirtings.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed bed laid jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L Kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10 mm thick in cement mortar 1:3 and jointed with white/coloured cement to match complete all as specified & directed

M&L for heavy duty pre-polished pavement tiles of size (300 x 300) as in footpath set over in CM (1:6) 15 mm thick screed bed including filling joint with white/coloured cement to match complete all as specified & directed

M&L for PCC 75 mm thick type C2 1:3:6 ( 40 mm stone aggregate), as in plinth protection, finished even and smooth without using extra cement.

M&L for 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) as in sub base finished even and fair.

M&L PCC 75 mm thick PCC 1:2:4 type B-2 ( Using 40 mm graded aggregates), for laying as sub base of floor finishes etc

M&L PCC 100 mm thick PCC 1:4:8 type D-2 ( Using 40 mm graded aggregates), for laying as sub base of floor finishes etc

M&L for 150 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) as in sub base finished even and fair.

M&L PCC 175 mm thick PCC 1:3:6 type C-2 ( Using 40 mm graded aggregates), for laying as sub base of floor finishes etc

M & L for Plain Cement concrete type B1 1:2:4 (using 20 mm graded stone aggregate) as in hardstanding, ramp and similar works surface finished even and fair complete all as specified and directed.

M & L for Plain Cement concrete type C1 1:3:6 (using 20 mm graded stone aggregate) as in roof kerbs or mud stops, rounded or champered on edges or as in coping, etc. complete all as specified and directed.

M&L RCC 1:2:4, type B-1 ( Using 20 mm graded aggregates), as in chajjas and similar suspended work in any situation.

Form work to chajja, weather shades, cooking platform, shelves incl fair finish surface of the concrete slab.etc

M&L mild steel TMT bar 10 mm dia (fe 500D) and over cut to length bent to shape including bending & binding with MS wire (annealed) not less than 0.90 mm dia complete all as specified and directed

Ditto all as item No 1.24 but 6 to 8 mm dia bar.

M&L running welding for new reinf with old reinf for binding exc 6mm but not exc 9 mm thickness

M&L On coat Nito bond EP applied on old concrete surface by brushing or spraying before placing new concrete .(it is required for bonding new concrete & old concrete).

Taking down cement plaster on wall; ceiling,etc incl racking out joints hacking for keys, scrubbing with etc complete all as specified and directed

M/L for rendering 15mm thick in cement mortar 1:4 finished even and fair complete all as specified and as directed.

M&L Rendering 15 mm thick cement plaster with WPC @ 3% of wt of cement on external surfaces of brick work in CM 1:4 and surface to be finished even and smooth without using extra cement (WPC will be measured and paid separately)

Supply only WPC

M&L Rendering 10 mm thick cement plaster in CM 1:3 on fair faces ceiling , Chajja, shelves and surface to be even and fair .

M&L Rendering 15 mm thick cement plaster on internal surfaces of brick work in CM1:6 and surface to be finished even and smooth without using extra cement .

M&L Preparation of old plastered surfaces of ceiling and applying two coats of white wash .

M&L Preparation of new plastered surfaces of ceiling and applying three coats of white wash .

M & L Washing, rubbing down and stopping of distempered and painted surfaces and applying two coats acrylic distemper (oil bound distemper) over a coat of wall primer incl preparation of surfaces in new plaster surface.

Complete removal of existing treatment surface and Washing, rubbing down and stopping of distempered and painted surfaces and applying two coats acrylic distemper (oil bound distemper) over a coat of wall primer incl preparation of surfaces.

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth.

M&L for applying two coats of cement based paint over a coat of alkali resistant primer on newly plastered surface of wall including preparation complete all as specified and as directed.

Complete removal of existing treatment surface and Washing, rubbing down and stopping of distempered and painted surfaces finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1:43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/10 Sqm as directed.

Preparation of new plaster surface of wall and finishig wall with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Taking down chowkath or frame exc 1.5 sqm n exc 4 sqm with shutter ( without taking of shutters from frames ) complete all as specified and directed.

Taking down chowkath or frame n exc 1.5 sqm with shutter ( without taking of shutters from frames ) complete all as specified and directed.

Supply and Fixing powder coated aluminium frame for doors, windows & ventilator with one or more rebates including joining cleat for fixing etc. complete all as specified.

Supply and Fixing powder coated aluminium window and ventilator shutter , aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, ruber packing, to recieve glass/wiremesh , screws , anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) in each shutter complete all as specified & as directed

Supply and Fixing powder coated aluminium door shutter of aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, anodised aluminium snap beading, screws etc including necessary fittings and fixes of handles,hinges,tower bolt complete all as specified & directed

S&F 19 mm thick veneered block board interior garde , solid core , general purpose type, with face veneers of type BB fixed with screw to timber frame work.

Supply & Fixed 4.80 mm thick plain sheet glass exc 0.5 sqm in each pane fixed to aluminium door,window & ventilator complete all as specified and directed.Make-Saintgobin/Modi guard/Atul

S&F 75 x 75 mm aluminium anodised grill of DG -916, 10 mm thick to aluminium window (Make - Deco grill)

S&F 140 mm floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring , fixed in floor.

S&F fpr 110 PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down

Demolition of cement concrete(un-reinforced) of any description and in any position not otherwise specifically provided for

M&L Applying evenly roof treatment using APP based polymeric membrane minimum weight 3.5 kg/sqm and 3 mm thick reinforced with polyster non woven fabric (weight not less than 150 gms/sqm) over a coat of primed and bonding surface by forced application,over a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per Sqm incl cleaning surfaces and including taking down old felt complete all as specified and directed.

M&L 25 mm thick PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in roof paddding/base for receive tile complete all as specified

M&L Rendering 10 mm thick cement plaster in CM 1:4 on roof surface .

Dismantling water tanks any type of capacity Exc 500 but n. exc 1000 liters and removing to store

S&F Rotational moulded polyethyene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in poisition all as specified in SSR Part I of capacity 1000 litre

Taking up or down steel tubing 15mm bore and connections, including cleaning for re-fixing or removal to store

Taking up or down steel tubing 20mm bore and connections, including cleaning for re-fixing or removal to store

S&F GI pipes medium grade 15mm dia with all fittings and fittings and fixed to walls and ceilings or laid in floors.

S&F GI pipes medium grade 20mm dia with all fittings and fittings and fixed to walls and ceilings or laid in floors.

S&F for 110 PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down

Demolition of brick work or stone/boulder masonry, built in cement mortar complete all as directed.

M/L for brickwork with flyash bricks,curved on plan exc 6m mean radius,built in CM 1:6

SCHEDULE 'A' PART-II (ELECTRIFICATION)

Taking down carefully copper /aluminium point wiring (light, fan socket or power) complete, including fixture and fittings such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC rigid conduit (medium grade) of size not less than 20 mm dia and conduit accessories with concealed wiring, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one light / fan point controlled by one 5/6 amps, one way switch including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC rigid conduit (heavy duty) of size not less than 20 mm dia and conduit accessories with concealed wiring, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for for one 5/6 amps socket outlet on same board controlled with other switch complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 1.5 Sqmm (phase & neutral) and one run of 1.5 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC rigid conduit (heavy duty) of size not less than 20 mm dia and conduit accessories with concealed wiring, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one 5/6 amps socket outlet on independent board controlled with one, oneway switch including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

M&L Point wiring with two runs of FRLSH grade PVC insulated unsheathed mulri-stranded copper conductor of size 4 Sqmm (phase & neutral) and one run of 4 Sqmm FRLSH grade PVC insulated unsheathed multi-stranded copper conductor for earth continuity wire to be drawn in and including PVC rigid conduit (heavy duty) of size not less than 20 mm dia and conduit accessories with concealed wiring, sunk MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick fixed with brass screws with cap washers for one 15/16 amps socket outlet on independent board controlled with one, 15/16 amps one way switch including all necessary wall cutting and making good disturbed surface with cement mortar 1:6 or PCC 1:3:6, type C-0 and matching with existing surfaces complete all as directed and specified.

Supply and fixing including connection of switch piano flush button type single pole one way 5 Amps.

Supply and fixing including connection of switch socket combination 5 Amps,2 in 1, 2/3 pin flush type.

Supply and fixing including connection of switch socket combination, 5 in 1,3 pin 5/16 amps flush type universal..

Supply and fixing of ceilings rose of PVC polycarbonate isolated body three terminals.

Supply and fixing of Step type electronic fan regulator flush type on the existing phonolic laminated sheet etc. as required.

Taking down unserviceable sub main /Sub circuit wiring of any type and size including conduit, batten wiring for necessary repair/replacement.

Supply and fix in repair circuit/sub-main wiring with PVC insulated & unsheathed two run of 2.5 Sqmm single core multi stranded copper conductor cable (FRLSH), 1100 Volt grade alongwith one run of 2.5 Sqmm PVC insulated & unsheathed copper conductor cable (FRLSH), 1100 Volt grade, connected to common earth dolly as earth continuity conductor, drawn through in pvc concealed conduit 20 mm bore heavy grade complete all as specified and as directed by the Engr-in-Charge.. Note : (i) Two runs of 2.5 Sqmm and one run of 2.5 Sqmm cable shall measured as one length.

Supply and fix in repair circuit/sub-main wiring with PVC insulated & unsheathed two run of 4 Sqmm single core multi stranded copper conductor cable (FRLSH), 1100 Volt grade alongwith one run of 4 Sqmm PVC insulated & unsheathed copper conductor cable (FRLSH), 1100 Volt grade, connected to common earth dolly as earth continuity conductor, drawn through in pvc concealed conduit 20 mm bore heavy grade complete all as specified and as directed by the Engr-in-Charge.. Note : (i) Two runs of 4 Sqmm and one run of 4 Sqmm cable shall measured as one length.

Supply and fix in repair circuit/sub-main wiring with PVC insulated & unsheathed two run of 6 Sqmm single core multi stranded copper conductor cable (FRLSH), 1100 Volt grade alongwith one run of 6 Sqmm PVC insulated & unsheathed copper conductor cable (FRLSH), 1100 Volt grade, connected to common earth dolly as earth continuity conductor, drawn through in pvc concealed conduit 20 mm bore heavy grade complete all as specified and as directed by the Engr-in-Charge.. Note : (i) Two runs of 6 Sqmm and one run of 6 Sqmm cable shall measured as one length.

Taking down old serviceable Ceiling fan including carrying out servicing and painting one with coat of synthetic enameled paint by spraying including filling cavities with filler, one coat cleaning all dust etc & writing necessary MES No at two places on the the fan and refixing fan in its own position after completion of necessary ceiling work

Supply and fixing in repair highly robust industrial Box type LED extruded Batten type indoor decorative type luminaire suitable for LED Tube 2x 16/20 watt (4ft ) complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable including taking down old light fitting complete all as specified and directed. ( Make /Model No :-IGP162LT8-16( ECO-I ) of Crompton or equivalant of Bajaj/Jaguar/Philips//Century Magik

Supply and fixing in repair highly robust industrial Box type LED extruded Batten type indoor decorative type luminaire suitable for LED Tube 1x 16/20 watt (4ft ) complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable including taking down old light fitting complete all as specified and directed. ( Make /Model No :-IGP161LT8-16( ECO-I ) of Crompton or equivalant of Bajaj/Jaguar/Philips//Century Magik

Supply and fixing in repair LED Polycarbonate T8 Tube with in built driver with metal heat sink double sided connection of capacity 1x 20 watts ,Make/Model No:-LT8-20-865-(2) ULTRON of Crompton

Supply and fixing in repair LED Building security light fitting of capacity 30 watt, new compact designed for the most effective thermal management IP 66 with highly effective and efficient lighting solution high power LED Building Security light including provn of necessary connection complete including taking down olf building security light (Make/ Model:- LSTS-30-CDL-M (ASTRA NEO) of Crompton or equivalent of Bajaj/Philips .

Supply , Fixing & testing of LED Flood light fitting of 70 Watt with electronic driver and made of pressure die cast aluminium housing with high power LED's as lighting source and lens embedded PC cover having TOP OPENING seperate driver compartment with IP66 protection and impact resistance of IK07 with LED fitting system lumen efficiency not less than 95% Lumen per watt and electronic driver with efficiency > 85% with inbuilt protection against lightning, over voltage, short circuit and surge/spike protection upto 5 KV ensuring longer life (THD <10%, PF shall be > 0.95, colour temperature 5700±300 K), Life expectancy of LED's minimum 50,000 burning hrs, warranty of complete luminaries fitting shall not less than three years. The fitting shall be tested LM 79 & 80 and test certificate shall be submitted from original manufacture. The light fitting shall be fixed on pole with and including 32 mm dia (or size as per manufacturers recommendation) light grade GI pipe (bend to shape or as per manufacturers recommendation) bracket 1.20 mtr long complete with MS flat iron clamp (clamps shall be 25 x 6 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer including connection complete all as specified and directed.

S & F Cable Junction Box PVC thermoplastic suitable for cable size 4-10 sqmm cable IP66/67 cable box size 155x 210 x92 totally enclosed with cable terminals and allumium bus bar 200 amps min (04 Nos) for cable incomer and outgoing ways : Make :HENSEL/WALTHER/EMITER Model No. KF-1610G

Supply and fixing in repair single pole and neutral sheet metal enclosure box including metallic two pin Plug and socket with 20 Amps MCB (SPN) 'C' series including connection with two runs of 4.0 sqmm.copper cable with one run 4.0 sqmm copper cable for earth continuity with taking down old U/S existing sheetmetal enclosure. ( Make L&T/Legrand /Standard).

Supply and fixing of VTPN DB double door,IK 09,IP43-Metal door, 4 way, made of CRCA sheet steel ,RAL 9003,powder coated with bus bar, neutral link, earth bar withprovision for DU125A MCCB,4 pole as incomer and SP/TP MCBs as Outgoings, including taking down old one.( Make/Model- DBVTL004DD of L&T or Equivalent of HPL/LEGRAND.

S&F MCCB 4 pole,125 Amps, for Incomer of VTPN with fixed thermal & magnetic release of breaking capacity 30kA,DU125H(Icu=30kA,Ics=50% Icu), 415 Volts.(Make: L&T,Cat No.CM90679OOLO or Standard/ HPL)

Taking down serviceable / unserviceable switch fuse unit/MCB DB with MCB etc for necessary repair/replacement and reuse all as directed by Engineer in Charge.

Supply and fixing of MCB DB double door, made of sheet steel phosphates, powder painted with bus bar, neutral link, earth bar and din rail SPN 8 way with 200 Amps rated bus bar 240 Volts including taking down.(Make:L&T/Standard/HPL)

S & F MCB 40 Amps SPN `C' series,Make:L&T,,Cat No-BB20400C or Standard/Legrand/HPL.

S & F MCB 40 Amps SP `C' series,Make:L&T,,Cat No-BB10400C or Standard/Legrand/HPL.

S & F MCB 06 to 32 Amps SPN `C` series,Make:L&T,Cat No-BB 10320C or Standard/Legrand/HPL.

Supply and fixing in repair of GI pipe Bracket of 40 mm dia light grade pipe bend to shape of approx length 1.5 Mtr including 2 no. MS Clamp of flat iron size 40x6 mm complete with nut, bolt, washers all as specified and directed. (Make of GI pipe- Jindal/Prakash/Tata)

M&L for earthing with galvanized steel earth plate electrode of size 600 mm x 600 mm x 6.0 mm buried directly in ground (earth pit not less than 2.25 Mtr below normal ground level ) connected to galvanized earth lead strip of size 25 mm x 3 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel including 40 mm dia medium grade GI tubing for protection of earth lead, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm dia, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type C1, 50 mm thick precast RCC (1:2:4) type B1 pit cover reinforced with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar including galvanised strip of size 25 mm x 3 mm for extension of earth lead and necessary excavation, earth work, in soft/loose soil and disposal of spoils to a disance not exc 50 mtr and necessary connection and testing complete all as shown in electrical plate No. 3 of SSR Pt-I including taking down old one , and all as directed and specified

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drwan in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc.as required 25x4 mm dia galvanised iron strip all as specified and directed.

Supply and fixing wall mounted fans, 230 volts single phase oscillating 400 mm sweep available in Grey , Azure Blue KD white & wine Red in colour (Modle No WM 1 Make -Crompton Greaves /Philips /Usha

Supply and fixing of exhaust fans AC single phase heavy duty Turbo force 380mm sweep, AC 230/240 volts, 50 HZ 900 RPM including louver & shutter and connecting up including provision of cable 3 core 1 sqmm from ceiling rose/connector to fan complete with rigid type flexible pipe of dia 15mm all as specified.

M&L for Cutting holes in to brick walls built in cement mortar for fixing of exhaust fan 300mm sweep including making good to disturbed surface in cement mortar 1:3 or cement concrete 1:2:4 type B-0 as required including grouting nut bolt and washer for fixing exhaust fan complete all as specified.

Supply, laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) with stranded aluminum conductor, 1100 volts grade, of size 10 Sqmm 2 core

Excavation in trenches not exc 1.5m deep and n.exc 1.5m wide and getting out in soft/loose soil for laying of cable all as specified and directed.

M&L for local sand coushioning with dry and clean over and under the cable for protection of cable , 80 mm sand laid before laying the cable & 150 mm sand after laying the cable and filling the sand in cable duct inside the sub station building complete all as directed

Returning, filling in, excavated soil (soft / loosel) including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing of excavated material not exceeding 50 m and depositing where directed at level not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point.

M&L for laying of bricks locally available sub class 'B' bricks (old size) for cable protection cover laid flat and dry in trenches over the cable prependicular to the direction of cable all as directed.

S&F ceiling fan 1200 mm sweep area, Kassels 50 ISI 1200 mm, white colour, 230 volt AC supply fix with MS clamp down rod complete with electronic step type fan regulator complete Make – Crompton sea wind (Opal white) or equivalent in Havells, orient, USHA (5 Star rates).

Supply, Installation, Testing and Commissioning of vertical bore well Submersible Pump Set suitable for bore size 300 mm, 3 phase 415 volts, 50 c/s, 2900 Rpm, 15 HP/11 Kw (Pipe size :- Suc/Del 80 x 100 mm), 50 CuM/Hr at 65 Mtr Head complete all as specified and directed.

Supply and lay submersible copper conductor cable flat, 1100 volts grade, 3 core, 6.0 sqmm PVC sheathed with multistranded copper conductor as per IS:694 including necessary end ferrules, water proof joints complete all as specified and directed.

Rekha Enterprises

Rounaq Enterprise

RANA ENTERPRISES

jlenterprise

CONSTRUCTION AND MAINTENANCE ENGINEERING CORPORATION

ELECTRO COMMERCIAL CO

DS ENTERPRISES

Bidder Name

RANA ENTERPRISES

DS ENTERPRISES

Rounaq Enterprise

J B NATH AND SON

Rekha Enterprises

ELECTRO COMMERCIAL CO

CONSTRUCTION AND MAINTENANCE ENGINEERING CORPORATION

jlenterprise