Urgent renovation works to guest rooms at Ground Floor of Officers Mess, Puducherry.

Amount

Supplying chemical emulsion in sealed containers including delivery as specified - Chlorpyriphos / lindane emulsifiable concentrate of 20%.

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - Treatment of existing masonry using chemical emulsion @ one litre per hole at 300mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 ( 1 cement : 2 coarse sand) to the full depth of the hole - with chlorpyriphos / lindane E.C. 20% with 1% concentration.

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - treatment at points of contact of wood work by chemical emulsion Chlorpyriphos / Lindane ( in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6mm dia holes at downward angle of 45 degree at 150mm centre to centre and sealing the same.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Vengai wood.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part 1) decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing specified wood frame work consisting of battens 50x25 mm fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete - Kiln seasoned and chemically treated Vengai wood.

Providing and fixing plywood 4mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with - Decorative veneer facings of approved manufacture.

Providing and fixing 18 mm thick, 150mm wide pelmet of coir Veneer board ISI marked IS : 14842, including top cover of 6mm coir veneer board, nickle plated M.S.Pipe 20mm dia (heavy type) curtain rod with nickel plated brackets, including fixing with 25 X 3 mm M.S. flat 10 cm long fixed to pelmet with Padak wood cleats of size 100 mm X 40 mm X 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc, all complete.

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P.brass screws and wooden plugs, etc., wherever necessary complete - 25mm dia.

Providing and fixing M.S.grills of required pattern in frames of windows etc with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete - Fixed to openings / wooden frames with rawl plugs screws etc.

Providing 40 X 5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30 x10 x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked powder coating sliding door bolts with nuts and screws etc.complte - 250 X 16 mm.

Providing and fixing ISI marked powder coating tower bolt black finish (Barrel type) with necessary screws etc.complete - 250 x10 mm.

Providing and fixing ISI marked powder coating tower bolt black finish (Barrel type) with necessary screws etc.complete - 150x10mm.

Providing and fixing ISI marked powder coating handles conforming to IS : 4992 with necessary screws etc.complete - 125 mm.

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete - 125 X 75 X 4 mm.

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete - 100 X 75 X 4 mm.

Providing & fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 type S, including cost of adhesive of approved quality - 1.0 mm thick.

Providing and fixing factory made uPVC white colour casement /casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing. (Single / double glass panes and silicon sealent shall be paid separately) - Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm ) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 + or - 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 0.75 sqm upto 1.50 sqm) - casement window size 1.00x1.35 m.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be manufacturer), of approved make (Jhonson / Asian / Somany / Nitco) in all colours, shades of size 300 x 600 mm as approved in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 300x600 mm.

Providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of first quality conforming to IS: 15622 of approved make (Nitco / Kajaria ) in all colours, shades, except white, ivory, grey, fume red brown laid on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing PVC corner beading of required size to suit the thickness of the wall tile at the corner joints of dado works.

20mm cement plaster of mix -1:6 (1 cement : 6 fine sand).

15mm cement plaster on rough side of single or half brick wall of mix - 1:4 (1 cement : 4 coarse sand).

Providing and applying ready mixed wall putty (JK / Birla) of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer.

Wall painting with plastic emulsion paint - Royal of approved brand and manufacture to give an even shade - two or more coats on new work.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacure.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc complete.

Wall painting with plastic emulsion paint - Premium of approved brand and manufacture to give an even shade - One or more coats on old work.

Melamine polishing on wood work (one or more coat).

Repair to plaster of thickness 12mm to 20mm in patches of area 2.5sqm and under including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead - of area 3 sqm and below.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - for thickness of tiles 10mm to 25mm.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Acid cleaning for the existing Mosaic floors , glazed tiles work and removing the stains and decays to give a glassy look etc complet (The Acid used shall be 32% concentrated hydrochloric acid after taking on the precautionary measures).

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required - white vitreous china anglet back wash basin size 600x480 mm with single 15mm C.P. brass pillar tap.

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete - flexiple pipe - 40mm dia.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing - rectangular shape 453 x 357 mm.

Providing and fixing 600x120x5 mm glass shelf with edges round off supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs etc., complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour - 600 mm long towel rail with total length of645 mm, 78 mm wide and effective height of 88mm, weighing not less than 190 gms.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand / make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flusing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect .

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and the cost of cutting chases and making good the same including testing of joints complete (Concealed work including cutting chases and making good the walls etc.) - 25 mm nominal outer dia pipes.

Providing and fixing unplasticised PVC connection pipe with brass unions - 45 cm length - 15mm nominal bore.

Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931- 15 mm nominal bore.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I.cover with frame (light duty) 455 x 610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10graded stone aggregate 40mm nominal size ), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete extra complete as per standard design - inside dimensions 600 x 850 mm and 45 cm deep for pipe line with three or more inlets - with common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Providing and fixing on wall / column face unplasticed - PVC soil and waste pipes (type - B) conforming to IS : 13592- 1992 including jointing with seal ring conformation to IS : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diametre.

Providing and fixing on wall face / column face unplasticised - PVC mould fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 110 mm.

Providing and fixing on wall face / column face unplasticised - PVC mould fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - heel rest bend 110 mm.

Providing and fixing on wall/column face unplasticised - PVC soil and waste pipes (type B) conforming to IS:13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - single socketed pipes 75mm diameter

Providing and fixing on wall / column face unplasticised - PVC moulded fittings /accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 75mm

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - heel rest Bend 75 mm.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawl strength of 1800 N (Face) and 900 N (Edge), minimum compressive strength 50N/sq.mm, modulus of elasticity 850 N/sq.mm and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S.screws, all as per direction of Engineer-in-charge. (Note: Stainless steel butt hinges and necessary S.S.screws shall be paid separately) - 30mm thick.

Providing and fixing netlon mesh.

Providing and fixing trap of (chilly cockroach trap) of self cleaning design with screwed down or hinged grating with, without vent arm complete including cost of cutting and making good the walls and floors 125mm inlet and 75mm outlet stainless steel as per IS 3989.

Providing and fixing of C.P brass health faucet of approved quality - 15mm nominal bore JAGUAR make as special type (Nos.573).

Providing and fixing of Mixture typ 3 in 1 and bond Sl.No.7281 Queen Jaguar make as special type.

Providing and fixing of C.P brass shower of Sl.No.1999 and arm of Sl.No.477 Queen Jaguar make as special type.

Providing and fixing Swan neck tap CP bress 15mm dia of BENELAVE (41003) foam type approved quality.

Providing and fixing PVC trap with PVC grating with or without vent arm complete including providing necessary lubricant and slip ring for fixing fittings, cost of cutting and making good the walls and floors- 110mm inlet and 110mm outlet.

Removing the existing colour wash by using scrapping machine, wire brush and other proper tools upto floor five level to ensure the surface free from loose particles, deposits, dust etc, complete as directed by the Enigineer-in-charge.

Removing the loose particles rust / mill scale deposits completely duly cleaning it with wire brush / crush sheet etc., and removing the dust over the old concrete surface and providing and system based aromatic rust remover of CERA / SIKA / FOSROC / Mc. Bauchmie / DON / BASF OR EQUIVALENT make certified and tested by accredited institutions (Confirming to IS 9077 - 1979 (reaffirmed - 1997) Appendix B, Clause 5.3.3) including all tools complete as per manufacturers specification and as directed by the Engineer-in-charge.

Mixing a polymeric cementitious Based bonding coat for bonding agent mixed thoroughly with mechanical mixing and applying the mix with brush on the prepared surface of the Column/ beams at the new and old concrete joint but the micro concrete should be laid with in 4 hours from the time of application with all lead and lift etc., complete all as directed by the Engineer-in-charge.

Plastering the wall surface with cement mortar of mix 1:4 (One part of cement: 4 fine sand) mixed with rubber latex polymer classic acryfix SBR, a Primadon product or its equivalent at the rate of 1kg for 1 bag the specification of M/s Primadon Construction Products Pvt., Ltd and as directed by the Engineer-in-charge.

Providing, cutting & fixing to required Shape and design 16mm thick plywood (BWR) For cupboard shutters/table top/ bottom/ sides/ partitions and the like. The rate is inclusive of cost of materials, wastages, screws, nails, fevicol SH special labour charges for making cupboard and shutters / furniture's and finishing the surface neat after fixing in required position as directed by the Engineer-in-charge.

Providing and fixing stainless steel Buttertly hinges with necessary screws etc., complete.

Providing and fixing flat teak wood - I class reepers of size 20 x 6mm alround the edges of plywood. The rate is inclusive of cost of materials, wastages, labour charges for fixing screws, nails, Fevicol SH and finishing the surface neat after fixing etc., complete as directed by the Engineer-in-charge.

Providing and fixing of stainless steel soap Dish No.1177 Sunken Basket Jaguar make.

Providing and fixing superior quality (CITIZEN) curtain cloth (Design candi D.No.221) with scallopping works etc., in the windows and doors. The rate includes the cost of curtain cloth stitching charges, fixing charges etc., complete as directed by the Engineer-in-charge (Note the area of the curtain cloth is dobled the area of the plan area including folding to 15cm on both top and bottom sides and wastage).

Dismantling the European water closet with fittings including stacking of serviceable material and disposal of unserviceable materials with in 50mts lead.

Dismantling of the Horizontal/ vertical water heater including connection as required.

Disposal of building rubbish and unserviceable dismantled materials upto 5 Km radius. The rate include incidental charge transportation by mechanical means loading and unloading etc., complete as directed by the Engineer-in-charge.

Providing and fixing multipurpose look for cupboard including necessary screws etc, complete (Lakshmi make).

Wiring for light point / fan point /exhaust fan point /call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc.as required - GROUP C.

Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required - 2 X 2.5 sq.mm + 1 x 2.5 sq.mm earth.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required - 20mm.

Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required - 15/16 A switch.

Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required - 6 pin 15/16 A socket outlet.

Supplying and fixing following size / modules , GI box alongwith modular base & cover plate for modular switches in recess etc. as required - 1 or 2 module (75mm x 75mm).

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required - Upto 450 mm sweep.

Supplying of 10" exhaust fan Make: Havells.

Supplying and fixing 4 feet, 20-24W system wattage LED tube light fitting with aluminium extruded heat sink and high efficiency polyearbonate diffuser suitable for surface mounting with on site warranty for three years. Make: Philips/ Wipro/ Hawells/ Crompton.

R CHANEMOUGAM