SPECIAL REPAIRS OF 03 TOILET AND BATHROOM (OTM) BLOCK OF BUILDING NO P-285 OF 4 JAK AT JAIPUR MILITARY STATION

Amount

Taking down cement plaster, any description on brick or stone walls, etc. incl. raking out joints, hacking for key, scrubbing down with water, etc.

M&L rendering 15 mm thick on stone masonary surface or surface or other surface fair face of brickwork in CM (1:6)

M&L rendering 15 mm thick on stone masonary surface or surface or other surface fair face of brickwork in CM (1:4)

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling

M & L preperation of new plastered surfaces of wall and applying three coats of white wash on walls complete all as specified and directed by engineer in charge

M & L for preperation of new plastered surfaces of ceiling and Applying three coats of white wash on ceiling surface complete all as specified

M&L Applying two coats of cement base paint white or tinted on new wall surface including preparation of surface

Taking down Chowkats or frames exc 1.5 sq. m each with shutters (without taking off shutters from the frames)

Taking down Chowkats or frames exc 1.5 sqm bur not exc 4 sqm each with shutters (without taking of shutters from the frames)

Providing and fixing 28mm thick factory made PVC Door Shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 40mmx20mm for stiles, top and bottom rails having a coat of steel primers of approved make. M.S. Frame covered with 4mm thick heat moulded Prelam PVC 'C' Channel of size 28mm thickness,75mm width out of which 60mm shall be flat and 15mm shall be tapered in 45 degree angle on either sides forming stiles, top and bottom rail and 100mm wide Rajshri Prelam PVC sheet out of which 100mm shall be be flat and 15mm shall be tapered An additional of 5mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete on both sides to form lock rail.Lock rail shall be provided on either side of panel. Panelling of 4mm thick PVC sheet to be fitted in the MS Frame welded/sealed to the stiles with 8mm (4mm + 4mm) x 12mm wide PVC sheet as beading on inner side and 8mm (4mm + 4mm) x 20mm wide PVC sheet as beading on the inner tapered side of lock rails joined together with solvent cement adhesive. An additional of 4mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification and drawing.

Providing and Fixing Factory made Adjustable (PVC) Door frame of the size 65mm x 60mm with a wall thicknes of 4mm, made out of extruded 4mm PVC foam sheet, metre cut at two corners and joined with 2 Nos. of 150mm long brackets of 15mm x 15mm M.S. Square tube. The two vertical door profile are to be reinforced with 40mm x 20mm M.S. tube of 19 guage through out the frame. The doorframe shall be fixed to the wall using 65/100mm long M.S. Screw through the frame by using PVC fastners. A minimum of 4 nos. of screws to be provided for each vertical member & minimum 2 nos. for horizontal member etc. complete as per manufacturers specification and direction of Engineer-in-Charge.

M&L 35mm thick IInd class hard wood factory made plain, framed, panelled shutter (two panel) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & steel as per IS:1003 (Part-I) kiln seasoned & chemically pressure treated.

M&L for Factory made steel ventilators with top hung shutters incl hinge steel peg stay complete incl. taking down old ventilator

M&L Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; barred iron doors ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M & L for preperation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by engineer in charge

M & L for preperation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by engineer in charge

S&F Butt hinges 100 mm size medium weight cold rolled mild steel.

S&F Mild steel barrel tower bolt 150 mm long stove enamelled black with bright bolt

S&F Mild steel pressed handles 125 mm size oval type stove enamelled black

M&L Mild steel sliding door bolt plate type stove enameled black with bright bolt not less than 12mm dia with & including a minimum of 6 bolt & nut, four on bolt plate & 2 on staple plate & fixed length of bolt 300 mm

S&F Sheet glass 4.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane

S&F in repairs Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe)

S & F in repair Water closet (Squatt pattern) complete including provision of cement concrete bedding including white colour Plastic seat cover with flat bottom and CP hinging device complete all as specified and directed by engineer in charge

S&F in repair PVC valve less syphonic action type low level flushing cistern coloured with inlet ball valve float and handle incl bracket 10 Lit capacity

Dismantalling of cast iron or reinforced concrete drain pipe jointed in CM and taking out of trenches if required internal dia of pipe 75mm/100 mm

S&F Cast iron 75mm bore Sand cast soil, waste & vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors,

S&F Cast iron 100 mm bore Sand cast soil, waste & vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors,

S&F Cast iron 75 mm bore Sand cast soil, waste & vent pipes, in any length with or without ears with cement joints, fixed to walls,

All as item no 28 above but 100 mm bore

S&F Cast iron 75 mm bore Bends (any radius),diminishing pieces or tapers (larger bore meassured )

All as item no 30 but 100 mm bore

S&F cast iron 75 mm bore branches pieces single (equal or unequal )ordianry or inverted (spigot or socket type ) or with paralllel branches

All as per item no 32 but 100 mm bore

S&F in repair cast iron 100 mm bore cowls

M&L cast iron floor trap 75 mm dia with grating incliuding jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 1000 ltr capacity including dismantalling old water tank

S & F Ball brass valves,20mm bore high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

S&F in repairs CP Bib taps 15 mm bore, long body, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule fancy type

S&F in repairs CP Stop valve 15 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions

All as per item no 39 but 20 mm bore

Dismantling and taking up or down the existing unserviceable GI pipe and M&L for new galvanised 15 mm bore steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors

All as per item no 41 but 20 mm bore

All as per item no 41 but 25 mm bore

M/L for Mild steel angle iron door frame 40x40x6mm conforming to Fe 410.0 incl.12 mm dia deformed bars( Tie bar) for strengthening at bottom of chowkhat incl.cutting floor to accommodate strengthening bar & making good in PCC(1:2:4) type B0.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

S&F Coloured Glazed ceramic tiles size 300x450mm x 7mm thick edge cut/ joint free , on walls etc in the combination of light and dark shade concept . set & jointed in neat cement slurry & pointed in white/coloured cement to match over 15mm thick plaster in cement mortar (1:4) Pattern and colour as directed by engineer-in-charge.

M&L for coloured Non Skid Ceramic tiles joint free 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc, set and jointed in neat cement slurry or tiles addeshive and pointed in white or coloured cement to match over and including 15mm thick Screed in cement mortar (1:4) Pattern as directed by Engineer-in-charge.

S&F in repair CP shower with shower arm 15 mm size , 195 mm long with bend of 45 degree with flange complete all as specified and directed by engineer in charge

Demolition of cement concrete in roof and floor other than ground floor

M&L for 40 mm thick PCC type D-2 (1:2:4) using 20 mm graded stone aggregate

M&L 50 mm thick PCC type C-1 (1:3:6) using 20 mm graded stone aggregate finished even and smooth without using extra cement as in plinth protection

Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as directed by Engineer-in-charge.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 40mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement.

M&L one coat of polymeric primer @ 0.30 Kg per sqm, conforming to IS : 3384. A layer of APP based polymeric membrane, 3 mm thick (min), weighing not less than 3.5 Kg/m2 reinforced with polyster non woven fabric ( weighing not less than 150 gms/ Sqm). Application of polymeric membrane shall be by torch application all as per manufacturer instructions

M&L applying one coat of alluminium paint on surface of any description wood,steel,iron, concrete,brick , stone etc exc 10 cm in width or girth, application of paint shall be as per manufacturers instructions.

Supply only Integral waterproofing compound

M & L PCC 1:2:4 mix type B-0 (using 12.5 mm graded aggregate ) as in roof kerbs rounded or chamfered on edges

Demolition of Brick work built in cement mortar

M&L Brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4)

M&L Brickwork with subclass `B' bricks, straight or curved on plan any radius in half brick thick wall, built in CM (1:4)

All as per item no 61 but except bricks

S&F Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern

S&F in PVC connections 15mm size with PTMT nuts of length 450mm

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste chain & plug & porcelain stopper but including brackets & Waste fittings 32mm bore and bottle trap complete all as specified and directed by engineer in charge

S&F in repair CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe

S/F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including bottle trap for outlet complete all as specified and directed by engineer in charge

M&L for preparation of old painted surfaces of wall and applying one coat of cement based paint of approved shade on walls all as specified & directed by Engineer-in-Charge

M & L for preperation of old painted surfaces of wall and applying two coats of white wash on wall complete all as specified and directed by engineer in charge

M & L for preperation of old painted surfaces of ceiling and applying two coats of white wash on ceiling complete all as specified and directed by engineer in charge

S & F peg set of six complete all as specified and directed

E/M Portion Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete including all fittings such as switches, ceiling roses, pendants, sockets, lamp holder, fan regulator brackets light fittings tube light fitting, bell/ buzzer etc (excluding fans) and making good disturbed surfaces of wall floors, ceiling etc complete all as specified and as directed by Engr-in-Charge to match with existing surface.

M&L Point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor FRLS cable of 1100 V grade PVC insulated and unsheathed cable inclosed in concealed conduit 20 mm dia medium grade with all accessories ISI marked, including MS sunken box for mounting fitting like switches, sockets fan regulators modulor type etc. including 1.5 sqmm single core PVC insulated but unsheathed copper earth continuty conductor to common earth and connected FRLS cable 1100 V grade as continuous earth wire to earth dolly

One light/fan/ bell point controlled by one, one way switch.

One 3 pin 5 Amp socket outlet on same board with other switches.

One 3 pin 5 Amp socket outlet on independent board with other switches.

All as per Item No 74.00 above but with 2.5 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, including 2.5 Sqmm copper cable continuous earth wire and connecting to common earth dolly.

S&F switch, piano type 230/250 volts :-

(a) Single pole, one way 5 Amp rating

(b) Single pole, one way 15 Amp rating

S&F Socket, piano type 230/250 volts

(a) Socket 05 Amp rating

(b) Socket 15 Amp rating

M&L Ceiling rose surface bakelite 65x50mm, three terminals.

Supply & fixing lamp holder PVC body complete all as specified and directed with 01xLED bulb 9 watt

Supply & fix Exhaust fan 380 mm sweep complete all as specified and directed

Supply & fix LED retrofit lamp ( size-4 feet), Regal Batten for LED tube, universal batten for T5 lamps surface/wall mounting IP 20 with twin core twisted flexible copper conductor cable with suitable size. Make - Havells cat No - REGALBATTENT5UPTO1X18WDSBSWH or equivalent cat part in other make as specified.

Supply & fixing Mirror surface mounted LED fitting 10 W (2 Feet)provided with a high output PMMA diffuser for glare free light , IP 20 with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size.

S&F in repair factory made, sheet distribution boards, SP&N 8 ways, double door protection class IP-42 double door type suitable for mounting MCB/ MCCB, confirming to IS-13032, IS-8623, BS-5484 with minimum 200 amps, copper bus bar

S&Fin repair MCB 10 KA confirming to IS-8828 : 1996, IEC-898 : 1995 rupturing capacity of the under mentioned type and rating :-

(a) SP 5 to 32 amps

(b) SPN 32 to 63 amps.

M & L Sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated unsheathed cable 1100 V grade with multistranded copper conductor ISI marked drawn throughn and including PVC rigid conduit/casing capping and conduit accessories fixed on surface/wall celing etc including provision of 1 run of 4 Sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity.

MSR INFRATECH

M/S Chandra Mohan Bansal

M/S ROHIT CONSTRUCTION

UNIVERSAL INFRAPROJECT PVT LTD

M/S Mohan Lal Gupta

Stuti Trading Company

VASU ENGINEERING SERVICES

SN TECHNO CONSTRUCTIONS

JAGDAMBA CONSTRUCTION COMPANY

M/s Bhavesh Construction Company