SPECIAL REPAIR TO BLDG NO. T-16 (OFFRS MD ACCN) IN ZONE -17 AT TALBEHAT MIL STN

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and directed.

Taking down chowkats or frames area not exceeding 1.50 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed. (Note – The quoted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

Taking down chowkats or frames area exceeding 1.50 Sqm and not exceeding 4.00 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed. (Note – The qouted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

Taking down shutters of any description not exceeding 1.00 Sqm each, from chowkhat complete all as specified.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each, from chowkhat complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

Material & Labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Material & Labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and inted in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per above but in skirting to walls including 10mm thick cement plaster in ement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed.

Material & Labour for coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 600X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick cement plaster in ement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed.

Material & Labour for HD Degital colour Ceramic tiles 8 to 10mm thick (Square/Rectangular) polished area of each tiles exceeding 0.42 sqm but n. exc1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Material & Labour for HD Degital colour Ceramic tiles 8 to 10mm thick (Square/Rectangular) polished area of each tiles exceeding 0.42 sqm but n. exc1.00 sqm, in Vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick plaster in cement mortar 1:4 complete all as specified and directed.

Material & Labour for Grenite 14 to 16mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces and half nose moulding (bull nosing) etc, complete all as specified and directed.

Material and labour for machine cut Prepolished Kota stone slab 20-25 mm thick (of size not less than 55 cm x 55 cm in flooring and 120 cm x 25 cm or as per size of treads (in treads) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including half round edge moulding, over and including cement screed bed 15 mm thick in cement mortar (1:6) base including rubbing and mirror polishing, and half nose moulding (bull nosing) etc,complete all as specified.

Material & Labour for machine cut Prepolished Kota stone slab 20-25 mm thick (of length not less than 55 cm in skirting and 120 cm or as per size of risers (in risers) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in vertical surfaces such as skirting and risers over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces, complete all as specified.

Material & Labour for 50 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete. Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

Supply and fixing for mild steel framed work as in door chowkats/gate of angle or angle iron work as in fixing of cooler stand by drilling/cutting the stone masonry wall and fixing up to 1st floor walls, other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides), complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid Decorative type flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with ecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) ®

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain type flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with ecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) ®

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain type flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with ecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) ®

Supply and fixing IInd class (hollock) hard wood factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on ther side & as gap insert for top rail & bottom rail; but wire gauzed i.e. panel will be of wire gauze in lieu of single side prelam PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing.

Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 45 mm x 70 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L for Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply & fixed 150 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply & fixed 150 mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S&F for 125mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and as directed

S&F 100 mm long stainless steel butt hinges with galvanised MS hinge pin etc.

S&F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified.

S&F double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber all as specified and directed by Engr-in-charge.

Supply & Fixed aluminium Hat and coat hooks, solid body, 175mm to 250 mm

Supply & fixed MS helical door spring 300 mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats.

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white owder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) (A) Area not exceeding 2.00 sqm each

S&F in position 4.8 to 5mm thick clear float glass of ordinary quality and glazing with glazing clips including necessary rubber packing to aluminium/uPVC frame n. exc 0.5 sqm in each pane complete all as specified and as directed.

S&F in position 4.8 to 5mm thick clear float glass of ordinary quality ground or obscured or forsted on one side and glazing with glazing clips including necessary rubber packing to aluminium/uPVC frame n. exc 0.5 sqm in each pane complete all as specified and as directed.

Supply and fixing galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified.

S & F in repairs 18 mm thick Celuka ply / PVC of grade 1 quality of both side plain white or colour fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by the engineer - in -charge. Make Rajshri /Black Cobra or equivalent.

S & F in repairs 18 mm thick Celuka ply / PVC of grade 1 quality of one side prelaminated and other side plain white or colour to make kitchen cabinet/ drawer shutters complete as per specifications and as directed by the engineer - in - charge.Make:-Rajshri/Black Cobra or equivalent

S & F 12 mm thick Celuka ply / PVC of grade 1 quality of both side plain white or colour fixed with screws, solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per specifications and as directed by the engineer - in -charge. Make Rajshri or equivalent.

S & F 6 mm thick Celuka ply / PVC of grade 1 quality of both side plain white or colour fixed with screws, solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per specifications and as directed by the engineer - in -charge. Make Rajshri or equivalent.

S & F auto closing hinges 35 mm of 0 crank (KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and as directed Make:- KAFF or equivalent

S & F stainless steel handles 100 mm size for kitchen cabinet shutters complete all as specified and as directed.

S & F Ball bearing runners 45 mm (length 20" to 25") Telescopic , full extension load capacity 50 kgscomplete all as specified and as directed Make:- KAFF or equivalent

S&F chrome plated stainless steel wire basket (storage basket) pull out type for large utensils, size 795 x 500 x 150 mm with necessary fixing clips etc complete all as specified and directed by Engineer-in-charge.

S&F chrome plated stainless steel wire basket (cup and saucer basket) pull out type, size 530 x 500 x 100 mm with necessary fixing clips etccomplete all as specified and directed by Engineer-in-charge.

S&F chrome plated stainless steel wire basket (plate basket) pull out type, size 530 x 500 x 100 mm with necessary fixing clips etccomplete all as specified and directed by Engineer-in-charge.

S&F chrome plated stainless steel wire basket (Thali basket) pull out type, size 530 x 500 x 200 mm with necessary fixing clips etccomplete all as specified and directed by Engineer-in-charge.

S&F chrome plated stainless steel wire basket (cutlery basket) pull out type, size 380 x 500 x 100 mm with necessary fixing clips etc complete all as specified and directed by Engineer-in-charge.

S&F chrome plated stainless steel wire basket (Grain Trolley) pull out type, size 380 x 500 x 200 mm with necessary sliding frame structure, fixing clips etc complete all as specified and directed by Engineer-in-charge.

S&F chrome plated stainless steel wire basket (storage basket) pull out type, size 530 x 500 x 100 mm with necessary fixing clips etccomplete all as specified and directed by Engineer-in-charge.

S&F chrome plated stainless steel wire basket (Bottle pull out) pull out type, size 120 x 500 x 432 mm with necessary sliding frame structure, fixing clips etc. complete all as specified and directed by Engineer-in-charge.

S&F in Stainless steel Magnetic door catcher size 5.08x2.54x2.54 cm with plate completed all as spd & directed.

Supply & fixed Continious piano hinges, continuous type of mild steel bright finish or electro galvanized with width of flap (when open) 30mm complete all as specified.

S&F Powder coated anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified

S&F powder coated aluminium anodized side hung type window/ventilators shutter without sash bars section weight not less than 0.55Kg/RM with extruded built up standard tubular and other sections of approved make according to IS(thickness of powder coating not less than 50micron including necessay glazing clips weight not less than 0.124Kg/Rm for fixing sheet glass anodized aluminium fittings/fixtures such as required number of roller of suitable size interlocking cleats/ plates etc as required for complete fixing window shutters complete all as specified and as directed by Engr-in-charge. Note:- Only aluminium shutters for the window shall be measured in sqm sheet glass and wiremesh etc shall be measured and paid in respective items

S&F powder coated anodized aluminium frames for door, window , ventilators with one or more rebates including joining cleats for fixing etc complete all as specified and as directed by Engr-in-charge

S&F in repair Stainless steel 20mm dia curtain rod including fixing brackets complete all as specified and directed.

S&F Stainless steel knobs with bracket fixing at end of pelmet rod complete al as spd & directed.

Taking down cement plaster from brick walls/stone masonry walls, concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on brick/stone masonry or concrete surfaces (internal walls) of any description, finished the surface even and smooth without using extra cement complete all as specified.

Material and Labour for 15mm thick rendering on fair faces of brick work/stone masonry, concrete surfaces (external walls) or stone walls upto tripple storey bldgs in cement mortar 1:4 mixed with liquid water proofing compound using as per manufacturer’s instructions, finished even and fair, complete all as specified. Note : (i) WPC shall be measured and paid separately. (ii) Rendering upto 9 mtr ht shall be included in the quoted rate).

Material and labour 5 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement all as specified and directed.

Supply only liquid water proofing compound, ISI marked complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty, complete all as specified and directed.

Material & Labour for preparation of new plastered surfaces of wall and applying two coats of weather coat over a coat of 1 mm thick wall care putty for neat and smooth finishing complete all as specified.

Material & Labour for preparing new plastered surfaces and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty on ceiling complete all as specified and directed.

M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of oil bound distemper (acrylic) white or tinted over a coat of priming over a coat of 1 mm thick wall care putty on walls/ceiling. complete all as specified and directed.

Taking down existing wall finishes any type by vigorously wire brushing, brooming dusting & finally washing with water to clear the surface absolutely free from any kind of existing finishes & foreign mtrls making good minor cracks etc in cement mortar 1:3 on the surface with uniform thickness making surface absolutely smooth,applying 1mm thick water proof wall care putty & applying two coats of exterior emulsion paint white or tinted over priming the surface with (100% Acrylic) Base coat of Apex ultima protek duralife and top coat of Apex Ultima protek, Make : Asian Paints) over a coat of alkali resistent primer through authorized applicator only complete all as specified and directed.

M&L for preparation of old painted surfaces of wood and wood based surfaces of any description, over 10cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted steel surface of any description, over 10cm in width or girth not other wise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for two coat of synthetic enamel painting to new wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer complete all as specified and directed.

M&L for two coat of synthetic enamel painting to new steel surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of red oxide primer complete all as specified and directed.

Supplying & laying 03 coats of reinforced acrylic coating ‘New Coat’ as on sunken floor applied @1.5 Ltr/Sqm in 03 coats to achieve total 1mm thickness in any position including cleaning surface of sunken slab with wire brush/mechanical brush and with water thoroughly to remove all dust/dirt and loose particles to expose base concrete/sunken slab etc including repairing of loose/defective joints and applying 15mm thick plaster in CM 1:3 to level the surface and treatment to be applied all as per manufacturers instructions, complete all as specified and directed.

M&L for PCC 1:4:8, type D-2 using 40mm graded stone aggregate as in foundations, fillings, mass concreting complete all as specified and directed.

Material & labour for PCC 1:2:4 type B-1 ( using 20mm graded mechanically crushed stone aggregate) as in bed blocks, copings, apex stones,side of interlocking tiles etc complete all as specified and directed.

Material & labour for 100mm thick PCC 1:2:4 type B-1, (20mm graded aggregate) as in sunken floor complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified.

Material and labour for providing reinforced cement concrete 1:2 :4 type B1 using (20mm graded stone aggregate ) as in cooking platform slab supported on wall, beam, cantilevers and kitchen cooking platform including necessary formwork complete all as specified.

Material and labour for repair to RCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in chajjas beams etc upto tripple storey bldgs including necessary formwork complete all as specified and directed.

Material and labour mild steel TMT bars, 8 mm dia and over, cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Taking down existing unservicable roof treatment of any description including cement plaster/cement concrete of any thickness from roof surface cleaning of roof surfaces and and preparing it for further treatment and removing rubbish from the site up to 1.5 Km to 2.0 Km complete all as specified and directed.

M & L for PCC 1:2:4 (B-0) using 12.5mm graded stone aggregate using WPC @3% by weight of cement as in roof top finished the surfaces even and smooth without using extra cement for laying roof treatement complete all as specified and as directed Note:- The water proofing compound measured & paid separately relevent Item.

M&L for Water proofing treatment on roof surfaces with APP modified membrane with non woven polyester reinforced, weight not less than 3 KG/SQM and thickness of membrane not less than 3mm having thermal insulation with white mineral/gravel finish on upper side of membrane uniformly embedded during manufacturing process laid in following sequence complete all as specified and directed.:- (a) Applying a coat of bituminous primer conforming to IS: 3384-1965 @ 0.4Kg/Sqm on the prepared surface till the surface is properly impregnated. (b) Laying APP modified water proofing membrane with 100mm overlap in longitudinal direction and 150mm overlap in transverse direction sealed and bounded to the surface by torch application method. (c) All joints and changes in direction should be curved with cement mortar 1:3 with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. A fillet of PCC 1:2:4 type B0 using 12.5mm graded stone aggregates shall be provided at all junctions of vertical and horizontal surfaces and wherever there is change of direction. (d) Applying one coat of Bituminous alluminium paint @ 0.20 Kg/Sqm over APP membrane. NOTE:- The quoted rates is deemed to include for the cost of scaffolding, T&P, etc required for execution of the work. The work of water proofing treatment shall be got executed through manufacturer or authorised applicator of the manufacturer

M & L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and as directed.

M&L for 10mm thick rendering on concrete surfaces of roof projection cornices & chajja etc finished fair and even without using extra cement including WPC in CM 1:4 incl taking down existing cement plaster and including necessary arrangements to work on roof projection, cornice & chajja etc.

Supply & fixed 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore all as specified and directed.

Supply & fixed Polymer coloured (Polypropeylene Delrin and ABS) low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS derscription mark with 2731 with and including suitable size of MS brackets, plug, screws all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed.

Supply & fixed in repair vitreous china wash hand basin flat back white of size 550mmx400mm with 32 mm dia chromium plated waste coupling including flush pipe etc complete all as specified.

Supply and fixing , vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified.

S&F in repair One piece ceramic floor mounted western water closet white with soft close seat cover including flush tank, trap and all fittings complete all as specified and as directed, Note:- The size, colour, design and Make shall be Approved by Eng-in-Charge. Make:- Cera, Parryware, Hindware, Jaqur.Prayag

S & F in repair vitreous china wash down water closet pan (pedestal pattern), white, including plastic white cover closed pattern with flat bottom and mild steel chromium plated hinge device including connections to drain (or outgoing pipe ) and to flushing pipe anti syphonage pipe etc complete all as specified and directed

S&F in repair Oval shape WHB size 605 x 430mmx200mm ,including CP waste coupling 32mm,waste pipe complete all as specified and directed.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion ordered and directed.

M&L for brick work with old size sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Supply & fixed in repairs stainless steel sink Kitchen or laboratory, made out of 1.00mm thick sheet with plug,washers, waste pipe, cast iron cantilever bracket of overall size 495x420mm bowl size 410x330x160mm complete all as specified.

S&F Half Turn / Quarter turn, 15mm dia CP central hole basin mixer without pop up waste system with 450 mm flexible hose for mixing of hot and cold water screwed for iron pipe and fixed complete all as specified and directed. Make : Parryware or Hindware , Prayag or Jaquar

S&F in repair Half/quarter turn chromium plated 15mm bore wall mixture 3 in 1 with provision for over head shower with 115 mm LB pipe & wall flange complete with bend pipe and wall flange, complete all as spfd & directed ,Make:_Cera, Parryware, Hindware, Jaqur.Prayag

S&F in repair 15mm bore concealed stop valve type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for union all as specified and directed by Engr-in-charge.

S&F in repairs Chromium plated bib taps, with capstan heads, screwed down for iron pipe or for brass ferrule & fixed for 15 mm bore pipe complete all as specified & directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges all as specified and directed by Engr-in-charge.

S&F in repair rotational molded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 500 Ltr hoisted and fixed in position after dismantling (water tank of cap exc 250 ltr and n.exc 500 ltr) and removing to store and all as specified and directed by Engr-in-charge.

S&F in repair rotational molded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position after dismantling (water tank of cap exc 500 ltr and n.exc 1000 ltr) and removing to store and all as specified and directed by Engr-in-charge.

S & F in repair gun metal gate valves, with iron wheel head, screwed both ends for iron pipe flange ends type fixed of 20mm dia all as spd and directed.

S&F in repair PTMT ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes all as specified and directed by Engr-in-charge.

Taking up or down steel tubing and connections of 15mm bore including cleaning for refixing or removal to store provision for branch connection by inserting tee union elbow etc. complete all as required at site.

All as item above but 20mm bore, complete all as specified.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction of Engineer-in-charge.

Material & Labour Steel Tubes 20mm bore, 'medium grade', galvanised, with all fitting; laid in trenches and fixed complete to brick/stone wall or laid in floor concealed, complete all as specified and as directed..

Refixing old steel tubing of 20mm bore and connections in new or old position (Walls, ceiling, floors, etc.

Supply & fixed in repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified.

Supply & fixed in repair fancy type shower rose125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint complete all as specified.

Supply & fixed in repair glass shelf assembly consisting of made out of 5.5 mm thick glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F for CP brass Soap Dish Holder, complete all as specified and as directed.

Demolition and breaking up 100mm dia drain pipes (Salt glazed ware, AC or Reinforced concrete ) set in cement mortar,complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls including GI stack clamp out of 30mm by 4mm flat iron and 12mm dia round stays bolts and nuts and securing ends of stays

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls including GI stack clamp out of 30mm by 4mm flat iron and 12mm dia round stays, bolts and nuts and securing ends of stays

S&F 75 mm bore PVC (SWR) bends any radius

S&F 110 mm bore PVC (SWR) bends any radius

S&F 75 mm bore PVC (SWR) junction single (Single T) equal or unequal

S&F 110 mm bore PVC (SWR) junction single (Single T) equal or unequal

S&F 100mm bore pipe PVC (SWR) vent cowls, complete all as specified.

S&F 75mm bore pipe PVC (SWR) vent cowls, complete all as specified.

Material and labour in repairs 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement. Complete all as specified and directed.

Material and labour in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

S&F of Solid FRP man hole cover of size 76cmx76cm with handle weight not less than 20 kg fitted to manhole any type complete all as specified and as directed. Make : Fluton polymers/Sigma or as equivalent brand all as specified and directed.

Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges in large patches as in roof covering complete all as specified and as directed. Note:- opening of existing wind tie where required for taking down of AC sheet is deemed to be included in the rate quoted .

Dismantling of timber scantling 40 Sqcm and over in section in any position such as in rafter, purlins etc in unframed work complete all as specified and as directed

S&F rolled mild steel section work as in main and cross beam, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates and cooler stand and similar work confirming to Fe 410W(Gde E-250 quality A) complete all as specified

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick, Trapezoidal roofing profile with 190 mm Pitch & 29 mm depth of profile of any colour having tensile strength of 550 Mpa fixed with self tapping screws as specified & directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick,Trapezoidal roofing profile with 190 mm Pitch & 29 mm depth of profile of any colour having tensile strength of 550 Mpa fixed with self tapping screws as specified & directed.(For sun shed)

M&L for 100mm thick PCC 1:4:8, type D-2 using 40mm graded stone aggregate as in Sub Floor , Sub Base, Floors and Pavings etc Complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in PCC band, PCC beam, benching of drain, coping,slightly rounded or chamfered angles and throating, and similar work as directed etc complete all as specified.

Machine pressed precast Rubber moulding reflective type concrete interlocking paver block with grey cement pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade of approved quality,laid over and include 50mm thick sand cushion vibtrated with mecanical vibrator complete all as specified and as directed.

Taking down carefully copper/Aluminum point wiring (light/fan/socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc., removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of wall, floors etc. complete all as directed.

Taking down carefully complete light fittings removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of wall, floors etc. complete all as directed.

Taking down Distribution Boards along with MCB's incl removing the same from site and making good to the disturbed surface complete. Note : All taken down MCBs should be deposited to MES store by the contractor without any extra charge.

Taking down existing sub main wiring of any type and description including removal of teak wood batten/pipe etc complete.

M/L for point wiring concealed type with 1.5sq mm FRLS PVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drown through in and incl FRLS PVC rigid conduit not less than 20 mm dia with its accessories pressed steel terminal/modular box incl 3mm thick laminated sheet for fixing switches/socket/regulators etc for the following: Wire: Make -Mescab/Polycab/KEI/Havells/Finolex PVC conduit: Make -Polycab/Precision/Plaza/Kalinga Note:- On RCC ceiling/column, false ceiling, AC/Metallic Sheet ceiling wiring done on surface with conduit/PVC Casing capping and its accessories.

One light/fan/bell point controlled by one No piano type switch 5 Amps single pole one way

One socket outlet 5/3 pin 6 AMPS controlled by one switch on the same board.

One socket outlet 5/3 pin 6 AMPS controlled by one switch on independent board.

All as per item NO 145 above but 3 pin socket out let 15/16 Amps on the independent Board all as spfd with single core unsheathed PVC insulated cable multistranded copper conductor of size 4 sq mm for phase & neutral & 4 sq mm for earth continuity conductor.

S&F Switch Piano Flush button single pole one way 5/6 Amp. MAKE:- Havells/Anchor/Gold Medal/Cona/Kinjal

S&F Switch Piano Flush button single pole one way 15/16 Amp. MAKE:- Havells/Anchor/Gold Medal/Cona/Kinjal

S&F socket outlet 2 in 1, 3 pin & 2 pin, 5/6 Amp, 240 volt. MAKE:- Havells/Anchor/Gold Medal/Cona/Kinjal

S&F socket outlet 2 in 1 , 3 pin & 2 pin, 5/6 Amp and 15/16 Amp, 240 volt. MAKE:- Havells/Anchor/Gold Medal/Cona/Kinjal

S&F ceiling rose surface bakelite 65mmx50mm 100watt three terminal. MAKE:- Havells/Anchor/Gold Medal/Cona/Kinjal

S&F step type electronic fan regulator flush type on the existing phenolic laminated sheet. MAKE:- Havells/Anchor/Gold Medal/Cona/Kinjal

S&F Lamp holder/Batten holder PVC/Polycarbonate insulated body with metal ring and back plate for batten fitting including 9 watt LED bulb complete. MAKE:- Havells/Anchor/Gold Medal/Cona/Kinjal

S&F Bell Ding Dong type, AC 230 Volts, Single pole. MAKE:- Havells/Anchor/Gold Medal/Cona/Kinjall

S&F Bell Push, flush type, 5 Amp, AC-230 Volts, single pole. MAKE:- Havells/Anchor/Gold Medal/Cona/Kinjal

M&L for sub main concealed wiring with two single core PVC insulated of size 6 sqmm FRLS unsheathed copper conductor 1100 volt grade multistandard and incl drawn through and including non metallic rigid PVC conduit and conduit accessories of 25 mm external dia and conduit FRLS accessories of ISI marks medium grade including 6.0 sqmm FRLS copper wire for earth continuity wire and connected of common earth dolly. Wire : Make -Mescab/Polycab/KEI/Havells/Finolex PVC conduit: Make -Polycab/Precision/Plaza Note:- (i) One run of conduit two run of 6 sq mm copper conductor & one run of 6.0 sq mm copper conductor is measured as one unit. (ii) On RCC ceiling/column, false ceiling, AC/Metallic Sheet ceiling wiring done on surface with conduit and its accessories. (iii) Cutting of wall, floor, PCC work and white wash for making of good to disturbed surfaces shall be included in the rate quated.

S&F Vertical Sheet Metal enclosure double door for MCCB DB Triple pole and neutral 4 way, (4+12) with 200 Amps rated bus bar 440 volts earth dolly IP-43, IK09, Make:- Legrand/Hager/Schneider/IndoAsian/Siemens/Havells Note:-MCB are measured and paid separately under respective items.

S&F MCCB TPN 63 Amp, 440 volt 'C' series, 16 KA, 50 Hz, confirming to IS/IEC-60898-1. Make:- As approved Make of DB

S&F in replacement single pole and neutral enclosure with a two pin and earth socket complete with one single pole MCB of 20 Amp 240 volt. Make:- Legrand/Hager/Schneider/IndoAsian/Siemens.

S&F sheet metal enclosure double door for MCB DB single pole and neutral 8 way with 200 Amps 240 volts double door (Metallic) type. Make:- Legrand/Hager/Schneider/IndoAsian/Siemens.

S&F MCB SP 6 to 32 Amps 240 volts 'C' series, 10 KA, 50 Hz, confirming to IS/IEC-60898-1. Make:- As approved Make of DB

S&F MCB SPN 40 to 63 Amps 240 volts 'C' series, 10 KA, 50 Hz, confirming to IS/IEC-60898-1. Make:- As approved Make of DB

Supply and fixing LED 4' batten light 18/20 Watt 230 Volt, complete connection with PVC insulated multi stranded copper flexible wire twin core of suitable size from nearest source complete all as specified and as directed by Engineer-in-Charge. Make Havells/Surya/Crompton/Philips/Bajaj

Supply and fixing complete LED light fittings mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver, holder and LED tube light including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make : Havells / Surya/ CG/Phillips

Supply and fixing LED building security light fitting, 15/20 Watt made up of pressure die cast aluminium housing, inbuilt driver, top opening, IP 66, 230 Volt, complete connection with PVC insulated multi stranded copper flexible wire twin core of suitable size from nearest source complete all as specified and as directed by Engineer-in-Charge. Make Havells/Surya/Crompton/Philips

Supply and fixing building securty light bracket bend type complete with 2.0m long G.I. pipe 40mm dia light grade, with suitble clamp and nut bolts complete all as specified and directed by EIC.

Note :- Debris obtained from all items should be removed in low lying areas as directed by Engr-in-charge out of MOD Land. (Rates quoted for items are deemed to be included for this, where removal of debris in the items is not considered.)