SPL REPAIR TO BLDG NO NP-34 (SINGLE MEN BARRACK) OF COMD HOSPITAL UNDER GE(NORTH) UDHAMPUR

Amount

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level), complete all as specified and as directed by Engr-in-Charge.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and as directed by Engr-in-Charge.

Demolition of brick work or stone masonary built in cement mortar including all quoins arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed by Engr-in-Charge

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and as directed by Engr-in-Charge.

Description all as per item No 4 above but except brick.

Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortor 1:4, complete all as specified and as direceted by Engr-in-Charge.

Non skid, light coloured, white printed ceramic jointfree/rectified tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc, set in cement slurry and jointed with spacers and pointed with liquid epoxy tile grout to match over and including 10 mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and as directed by Engr-in-Charge.

Glazed coloured ceramic jointfree/rectified tiles 450mm x 300mm x 7 to 8mm /600 mm x 300 mm x 7 to 8mm thick on vertical surfaces of walls as in dado/skirting etc., set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 10 mm thick screed bedding/ backing layer in CM 1:3, complete all as specified and as directed by Engr-in-Charge.

Plinth protection 50 mm thick in PCC 1:3:6, type C-1 ( using 20 mm graded crushed stone aggregate ) laid in alternate bays (not exceeding 2 Sqm each) finished even and smooth without using extra cement and providing joints through out the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and as directed by Engr-in-Charge.

Water proofing treatment to the sunken portion with removing of exiting treatment including WC & P/S trap and cleaning with wire brush , one coat of bitumen @ 1.7 Kg per sqm , 15mm th plaster in CM 1:3 on all sides and bottom incl mixing water proofing powder , one 450mm long 32 mm dia spout, provn of lime conctere for filling, completed and specified and directed by Engr-in-charge .

Vitreous china water closet, 'Squat pattern, including lime concrete bedding, size 580 x 440 mm white with integral foot rests excluding flushing cistern and flush pipe but including connection to trap, anti syphonage pipe etc. complete fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

10 ltr capacity PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision, complete all as specified and as directed by Engr-in-Charge. MAKE: Cera Model Combiflush twin flush as per Cat Part No. 2603 or equivalent in performance of makes as specified in PS.

S&F Oval under counter wash basins, size 560x470mm vitreous china fixed in RCC slab including CP waste coupling 32mm and CP brass bottle trap 32mm bore including 32mm HDPE pipe bend fixed to wall etc as in waste pipe and 300mm long (Cera CM104B) all as specified and as directed by Engr-in-Charge. Make: CERA cat part No. 1005A (Ivory color) for WHB or equivalent in performance of makes as specified in PS.

WHB mixer fancy type chromium plated cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions suitable for 15 mm borw, complete all as specified and as directed by Engr-in-Charge. .

Soap dish fancy type chromium plated fixed with brass screws and wooden/plastic cleats complete all as specified.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed by Engr-in-Charge

PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified.

Taking down eaves gutters and rainwater pipes/soil pipes (any size, type or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., for (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and as directed by Engr-in-Charge.

110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and as directed by Engr-in- Charge.

Description all as per item No 19 above but 75 mm bore.

110mm bore, PVC (SWR) pipes, single or double socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engr-in- Charge.

Description all as per item No 21 above but 75 mm bore.

110 mm bore PVC SWR bends any radius with acess door and fixed with solvent etc complete all specified and as Directed (ISI Marked)

Description all as per item No 23 above but 75 mm bore.

16-18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including necessary bull nosing in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting and mirror finish polishing over and including 20 mm thick screed bedding/ backing layer in CM 1:3, complete all as specified and as directed by Engineer-in-Charge.

Dismantling water tank of capacity exceeding 250 litres but not exceeding 500 litres each and removing from site/to store, complete all as specified and as directed by Engr-in-Charge.

Rotational moulded polyethylene water storage tank , three layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 2000 litres each including all accessories (i.e GI nipples and Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of bore 20mm (Minimum weight 210 gram) etc),complete all as specified and as directed by Engr-in-Charge.

Taking up or down 15mm bore steel tubing and connections including all fittings and removing to store.

Taking down 20mm Bore steel tubing and connections including all fittings and removing to store.

Taking down 25mm Bore steel tubing and connections including all fittings and removing to store.

15mm bore galvanised steel water tubing medium grade (ISI Marked) with and including all fittings and fixed complete to walls and or laid under floors etc complete all as specified.

20mm bore galvanised steel water tubing medium grade (ISI Marked) with and including all fittings and fixed complete to walls and or laid under floors etc complete all as specified.

25mm bore galvanised steel water tubing medium grade (ISI Marked) with and including all fittings and fixed complete to walls and or laid under floors etc complete all as specified.

Bib taps long body, cast copper alloy, chromium plated, with crutch or butterfly handle screwed down for iron pipe or for brass ferrule for bore of pipe 15 mm fixing in repair, complete all as specified and as directed by Engr-in-Charge. Make : Jainko Cat part No LBJ-1 or equivalent approved.

15mm Brass chromium plated fancy overhead shower with arm, fixing in repair complete all as specified. Make : Jainko Cat Part No: FSJ-1 /or equivalent of makes specified in PS.

Angular stop cock/Angle cock with wall flange, fancy type, brass, chromium plated, screwed down for iron pipe or for brass ferrule for bore of pipe 15 mm, fixing in repair, complete all as specified and as directed by Engr-in-Charge Make : Jainko Cat part No AVJ-1 or equivalent of makes specified in PS.

Stop valves, fancy type, chromium plated, cast copper alloy, with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore 15mm fixing in repair , all as specified. Make : Jainko Cat Part No CSV-1 or equivalent of makes specified in PS.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 25mm, fixing in repair, complete all as specified.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, removing all type of vegetation (like peeple tree etc) scrubbing down with water complete, all as specified and as directed by Engr-in-Charge.

10mm thick rendering on other than fair faces of brick or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

Applying two coats of oil bound distemper over a coat of primer including preparation of new plastered/ unplastered surfaces of wall, complete all as specified & directed by Engr-in-Charge.

5mm thick rendering on brick or concrete surfaces as in ceiling in cement mortar 1:3, and finish the surface even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

Preparing plastered or unplastered new surfaces of wall and applying three coats of white wash, complete all as specified and as directed by Engr-in-Charge.

Preparation old surfaces including complete removal of existing treatment and applying three coats of white wash on ceiling all as specified

Cleaning and refixing steel tubing of 15 mm bore with connections, complete all as specified and as directed by Engr-in-Charge.

Cleaning and refixing steel tubing of 20 mm bore with connections, complete all as specified and as directed by Engr-in-Charge.

15mm thick rendering on other than fair faces of brick or concrete surfaces in cement mortar 1:4, finished even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

Preparing plastered or unplastered new surfaces of walls and applying two coats of cement base paint over and including one coat of primer, complete all as specified and as directed by Engr-in-Charge.

Brass chromium mixer for wall,hot and cold water fancy type fixed with iron pipe suitable for 15 mm bore,complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed by Engineer-in Charge.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour (shade as apporved by GE) PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings complete all as specified.

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour (shade as apporved by GE) PVC sheet on back face, with particle board core, supplying & fixing in frame at site as per specification & drawing as per specification & drawing, complete all as specified and as directed by Engr-in-Charge.

S&F Factory made Pressed Steel windows / Ventilators with glazed & gauzed shutters (Combined with side hund shutter incl box type hinges) steel handle and necessary tacking arrangement, peg stay complete with one shop coat of red oxide zinc chrome primer complete all specified and as directed. Note: (i) The window shall be fabricated as per Drg No CEUZ/TD/1517/15 Sheet 1/3 to 3/3. (ii) Rate quoted are included for wire gauzed & glazed window complete & shall be measured as overall out to out one side only.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar, barred iron doors; ladder, framed balusters; railing; frame work for water tanks, cooler stand etc and similar work conforming to FE 290-0 or Gde-E-165, complete all as specified and as directed.

Preparation of new steel and iron surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over preprimed surfaces, complete all as specified and as directed by Engr-in-Charge.

Preparation of new steel surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of zink chrome primer complete all as specified.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staples complete, all as specified and directed by Engr in Charge.

4.00 mm thick plain/pin headed sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 10mm thick screeding in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric five layred APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.50 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm, and apply two coat of aluminum paint over one coat of primer over APP after treatment complete all as specified and as directed by Engr-in- Charge.

Supply only liquid water proofing compound, complete all as specified & directed by Engr-in-Charge. (Make : Dr Fixit, LW+, STP Ltd No 1 (L) & SIKA or equivalent as specified in PS)

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square and not exc. 4.00 Square each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt. ) , complete all as specified and directed by Engineer-in Charge.

Pressed steel frames for doors, made out of 12.5 mm thick MS sheet, with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 125 mm x 60 mm, including one shop coat of red oxide zinc chrome primer, including filling voids with PCC 1:3:6 type C-0 complete all as specified and as directed by Engr-in-Charge.

40mm thick flush shutters, solid core construction, with block board core and plywood face pannels and one face is covered with decorative face veneer with liping/frame to match, complete all as specified and directed by Engineer-in charge.

35mm thick, factory made 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified .

25mm thick flush shutters, solid core construction, with block board core and plywood face pannels and one face is covered with decorative face veneer with liping/frame to match, complete all as specified and directed by Engineer-in charge.

200 mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. (ISI Mark)

200 mm long aluminium bow handles, cast type anodised complete all as specified and directed. (ISI Mark)

300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete, all as specified. (ISI Mark)

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, 140mm overall length of cover plate complete all as specified and directed. (ISI Mark)

S&F MS, 150 mm, ordinary pattern helical door spring including roller and roller plate fixed to wooden or steel frames with welding etc.

CP tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodized, fixed with rawl plugs. complete all as specified in repairs. Make : Jainko Cat Part No - TRJ-2 or equivalent of makes specified in PS.

CP towel ring (round), fixed with rawl plugs. complete all as specified in repairs. Make : Jainko Cat Part No - TRR-1 or equivalent of makes specified in PS.

Dismantling loose/disintegrated portion of RCC chajjas, bends shelves, beams balconies and similar work at any position or any height and dubbing out with PCC 1:1.5:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished required shape including applying anti corrisove paint on exposed surfaced and provision of necessary support form work and including 10mm thick plastering in CM 1:4 finished fair and even completed all as specifed.

75mm bore PVC(SWR) multi floor traps with stainless steel grating including jointing to waste pipe fixed cncrete type B1 (1:2:4). complete all as specified and as directed.(ISI Mark)

Reinforced cement concrete 1:2:4 type B1, (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed by Engr-in-Charge.

TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and includingMS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engr-in-Charge.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc to obtain rough flat finished surface of concrete complete all as specified and as directed.

Machine cut kota stone slab flooring 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including Screed bed or bedding layer of mortar 20mm thick in cement mortar 1:3, complete all as specified. Note: 80mm wide strip of white marble 15 - 16mm thick machine cut bedded jointed and pointed with gray cement shall be provided alround.

Description all as per srl item No 79 above but in vertical surfaces like dado/skirting, etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering (backing) on fair faces of brick/concrete surfaces works in cement mortar 1:3, complete all as specified and as directed by Engr-in-Charge.

Machine cut kota stone slab flooring 18-20 mm thick in riser of steps one piece including necessary bull nosing, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, over and including 15 mm thick rendering on fair faces of brick/concrete surfaces works in cement mortar 1:3 finished rough for receiving tiles including cutting and polishing over and including 20 mm thick CM 1:3 mortar backing for fixing the stone slab, complete all as specified. complete all as specified and as directed by Engr-in-Charge.

4mm thick Plain mild steel wire, galvanised class 3, in mosquito or cloth hanging including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, to Angles or etc, complete all as specified. (each line of wire to be measured) complete all as specified.

Providing precast cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) louvres and jallies, 50mm thick (measured solid) , including all mouldings but excluding frame Set in cement mortar 1:4, complete all as specified.

MS powder coated drapory rods of 22 mm dia decorative type with wooden finish alongwith holding for brakets & end caps. In repairs complete all as specified.

Vitreous china urinal, half stall type white incl CP Spray Nozzale including PVC waste pipe, providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement , HDPE flush pipe, grating and union for discharge pipe, incl PVC waste pipe 32mm dia, fixed in repair, complete all as specified.

Mild steel, 0.50 mm thick Plain Galvalume sheeting made to shape of covering for crumple sections, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified and as directed by Engr-in-Charge.

Pre-painted coloured corrugated profiled Galvalume/Zincalume sheet with min 0.50mm TCT with BTM of 0.45mm thick conforming to IS -513(AZ-150 GSM,Al Zn alloy metallic coating 550MPA yield stress as per AS-1397),as in roof covering/clading to wall fixed with self taping screws, colour/exterior coat of silicon modified polyster/ BHP x RW paint system 20 micron top coat applied over 5 micron primer and a micron polyster back coat applied over 5 micron primer,all fixed with galvanised self drilling self tapping fastener(12-14x55 with EPDM seals), complete all as specified and directed

Gully Trap 125/110 PVC (SWR ), setting and jointing with solvent cement in repair, complete all as specified and as directed.

75 mm thick, Plain cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregates) as in sub base for laying floor finishes including finishing the surfaces even and rough , complete all as specified and as directed by Engr-in-Charge.

S&F factory made heavy duty full body digital matt finish paving colored tiles of size 300mm x 300mm x 10mm thick for external use laid over and including 15mm thick screed bed or bedding layer in CM 1: 4 including jointed with neat cement slurry and pointed in colored tile epoxy grout to match over the shade of tiles complete all as specified and as directed by Engr-in-Charge. Make Durastone of Somany, Pavinres of Kajaria, Endura of Johnson.

Plain cement concrete 1:3:6 type C-1 (using 40mm graded crushed stone aggregates) for filling in hold fast or as in coping packing overall or similar work including necessary formwork as required complete all as specified and as directed by Engr-in-charge.

Providing, pre-cast cement concrete 1:2:4 type B-I (20mm graded) as in kerb stones and in similar works including weathering, slightly rounded or chamfered angles and throating and necessary form works and jointed in cement morter 1:4, complete all as specified and as directed by Engr-in-Charge. (Size : to be approved by Engr-in-Charge)

150 mm bore reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed

250 mm bore reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed

Plain cement concrete 1:4:8 type D-2 (using 40mm graded aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore pipes all as specified.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 250mm bore pipes all as specified.

Pre-cast cement concrete 1:2:4 type B-I (20mm graded) as in manhole cover slab, chullah hoods and in similar works bedded and jointed in cement morter 1:4, complete all as specified and as directed by Engr-in-Charge.

TMT mild steel bars, 6 to 8 mm dia, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and includingMS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engr-in-Charge.

Dismantling of cast iron or reinforced concrete drain pipes, any size jointed in cement mortar and taking out of trenches or fixed to wall, if required complete all as specified and as directed by Engr-in-Charge.

Taking down carefully copper /aluminium, point wiring (light, fan, socket or power) complete including fittings and fixtures such as light fittings, switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of wall, ceiling, floors etc, complete all as specified and as directed by Engr-in-Charge.

Point wiring with 1.5 Sqmm PVC insulated, unsheathed (FRLS) cable with multi stranded copper conductor wiring in and including PVC concealed conduit medium grade (ISI marked) 20mm dia and over, wall thickness not less than 2.00 mm thick , and all accessories for one light /fan/ bell controlled by one switch with 1.25mm thick pressed steel terminal anodized box concealed on walls, 3mm laminated plastic sheet cover for mounting of switches, socket outlet, regulator etc, fixed by suitable size of 4 Nos cadmium screws along with PVC insulated and unsheathed FRLS 1.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly, complete all as specified and as directed by Engr-in-Charge.

Description all as per item No 101 above but one 3/5 pin 5 Amp socket outlet on the same board with other switch.

Description all as per item above No 101 but one 3/5 pin 5 Amp socket outlet on independent board .

Description all as per item No 101 above but one 3/5 pin 15 Amp socket outlet on independent board with PVC insulated, unsheathed FRLS cable 2.5 Sqmm copper multistrand conductor, along with PVC insulated and unsheathed FRLS 2.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly complete all as specified and as directed by Engr-in-Charge.

Switch piano type 5 Amps single pole one way 240 volts complete all as specified and as directed by Engr-in-Charge.

Switch socket combination, 2 in 1, 3/5 pin, 5/6 Amp flush type, complete all as specified and as directed by Engr-in-Charge.

Switch socket combination, 2 in 1, 3/5 pin, 5/6 & 15/16 Amp flush type, complete all as specified and as directed by Engr-in-Charge.

Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Block, complete all as specified and as directed by Engr-in-Charge.

Slim linear LED lighting fixture 20 Watt LED Batten, with full base of extruded aluminium section acting as a heat sink with closed back, isolated driver, CRI ≥ 70, PF ≥ 0.9, Surge protection upto 2.0 kV, shatter proof opal sheet of polycarbonate diffuser with system efficacy ≥ 100 Lm/watt, operating voltage 170-240 volts, colour temp 6500K, Low heat generating LED, complete making all connections using 1.5 Sqmm copper conductor multi strand PVC insulated 2 core flexible cable from ceiling rose to fitting complete all as per the directions of Engr-in-Charge. Make : Havells cat Pt No LHEXBYPNIN1W020 or equivalent to CG/SYSKA Cat No- SSK-ALB-20W.

Supply and fixing LED Decorative Ultra Slim linear 9/10 watt LED Lightening Fixture (Mirror Light) with full base environmental acting as a heat sink with closed back, isolated driver, system efficacy ≥ 100 Lm/watt, operating voltage 170-240 volts, colour temp 6000K, Low heat generating LED (Make of LED shall be Cree/Nichia/Osram) complete making all connections using 1.5 Sqmm copper conductor multistrand PVC insulated 2 core flexible cable from ceiling rose to fitting complete all as per the directions of Engg-in-Charge. Note : (i) A certificate from the manufactures for warranty minimum upto 2 years shall be obtained and submitted to the AGE/GE (ii) Any touch up of the wall surface due to changing of fittings shall be done by contractor with similar surface finish without extra cost to the department. Make – Havells Cat Pt No LHEXARP6PN1W009, SYSKA Cat Part No. SSK-T5T-9W or Equivalent in Philips/Havells/Surya .

LED bulk head luminaire, 12 watt surface mounting type extruded aluminium body with diffuser and connecting up with flexible copper conductor cable of suitable size complete all as specified and directed. Make : Wipro Cat Pt No DA11265, or equivalent in performance of makes as specified in particular specifications.

Supply and fixing LED Street Light fitting 20 Watt, New generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP66 with acrylic, powder coated, pressure die cast aluminium compact high power LED tube light with heat resistant toughened Glass, Corrosion resistant, isolated driver low heat generating (Make of LED shall be CREE/Necia/Osram) LED including nuts, bolts, washers with suitable size/dia 40mm GI pipe bracket for fixing of street light including making all connection, complete all as per the direction of Engg-in-Charge. Note : (i) A certificate from the manufactures for warranty minimum upto 2 years shall be obtained and submitted to the AGE/GE (ii) Any touch up of the wall surface due to changing of fittings shall be done by contractor with similar surface finish without extra cost to the department. Make :SYSKA cat No. SSK-NST-20W or equivalent in CG Cat No. LST-20-CDL.

M&L for repair of ceiling fan 1200mm sweep of any make obtained from above item, oiling, greasing cleaning slot, over hauling & replacement of defective nut bolts washer etc including painting all as specified and directed by Engr- in-charge.

Hanging/fixing only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan obtained from item No-113

Fan regulator 120W, 230V 50 C/S, flush type electronic, step type hum free suitable control speed of fan from 0 to 100 % and connecting electrically on the existing phenolic laminated sheet complete all as specified and as directed by Engr-in-Charge.

Taking down old unserviceable copper /aluminium,submain wiring any type/size from existing old surface for further repair/replacement, complete all as specified and as directed by Engr-in-Charge.

Sub main wiring with two runs of 6 Sqmm ( 2x6 sqmm ) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor conforming to IS-694 drawn through and including non-metalic PVC rigid concealed conduit 25 mm dia medium grade (ISI marked) with all conduit accessories mounting on suface of walls /roofs / ceiling etc with one run of 6 Sqmm (1x6sqmm ) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire, fixed in repair, complete all as specified and directed by Engr-in-Charge. Note:- 2 runs of 6 Sqmm (2x6sqmm ) ,one run of 6 Sqmm (1x6 sqmm ) cable and one metre of conduit will be measured as one unit.

Sheet metal enclosures for distribution board when MCB to be used TPN 4 way 415V with 200 Amps rated bus bar, double door type with IP-43, IK-49 protection with neutral link fixed flush in wall including cutting chases in walls for fixing DB and making good disturbed wall surfaces to match the existing specifiactions ,fixing in repairs complete all as specified and as directed by Engr-in-Charge.

MCCB 4 pole,415 volts 200 Amps with breaking capacity 25/26 KA with thermal adjustable, complete all as specified and as directed by Engr-in-Charge. Make : Legrand cat part No - 420217 / Indoasian Cat part No -8536 or Scheinder

Sheet metal enclosures for distribution board when MCB to be used SPN 8 way with IP-43, IK-09 protection 240V with 200 Amps rated bus bar, double door type including cutting chases in walls for fixing DBs making good the distubed surfaces to match with existing specifications ,fixing in repairs complete all as specified and as directed. Make- Havells cat pat No- DHDNSHODDW08/legrand/ABB /Indoasian or equivalent in performance of makes as specified in PS.

Sheet metal enclosures for distribution board when MCB to be used SPN 12 way with IP-43, IK-09 protection 240V with 200 Amps rated bus bar, double door type including cutting chases in walls for fixing DBs making good the distubed surfaces to match with existing specifications ,fixing in repairs complete all as specified and as directed. Make Legrand(Ekinox3) Cat No 507612 Ekinoxe/Schiender (Acti-9) /Siemens(Betagard-8GB32).

MCB SP, 6 to 32 Amps,240 Volts including providing aluminuium thimbles for outgoing cable, complete all as specified and as directed by Engr-in-Charge. Note : The exact capacity of MCB shall be as directed by Engr-in-Charge.

MCB SPN, 40 to 63 Amps, 240 Volts including providing copper thimbles for outgoing cable, complete all as specified and as directed by Engr-in-Charge.

Sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20Amps, 240V complete with one single pole MCB of capacity 20 Amps of breaking capacity 10KA, complete all as specified and as directed by Engr-in-Charge.Make:- Indoasian- Optipro Cat pt No- 811956/Legrand/Schneider or equivalent in performance of makes as specified in PS

Supply, laying and testing of XLPE insulated sheathed armoured heavy duty LT 1100 Volts grade cable with aluminum conductors laid in trenches/pipe, fixed to poles, walls of size 70 sqmm 3.5 core, complete all as specified and as directed by Engr-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying cables/pipes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth in soft/loose soil, complete all as specified and as directed by Engr-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying cables/pipes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard/dense soil, complete all as specified and as directed by Engr-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying cables/pipes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/disintegrated rock , complete all as specified and as directed by Engr-in-Charge.

Returning, filling in (soil) including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in any type of soil, complete all as specified and as directed by Engr-in-Charge.

Removal of excavated material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5m above the starting point , complete all as specified and as directed by Engr-in-Charge.

Dry coarse sand as cushioning to under ground cable provided with layer of 8 cms deep before laying the cable and 15 cms deep after laying and stretching the cable, punned to 18 cm thick complete all as specified and as directed. NOTE Only punned thickness shall be measured for payment purpose.

Brick covering with width equal to length of brick as mechanical protection to cable using sub class ‘B’ bricks laid flat of size 230mmx115mmx75mm complete all as specified and as directed by Engr-in-Charge.

GI tubing light grade 40mm bore along the wall/in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holding of GI pipe alongwith poles complete all as specified and as directed by Engr-in-Charge.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 mtr below normal ground level, connected to and including 4mm dia galvanized iron wire lead by means of bolts, nuts, check nuts and washers of galvanized standard iron or steel all as specified or indicated in electrical plate No 3 of MES Part-I, including testing on completion including the material and labour and taking out old unserviceable earthing of the following :- (a) Excavation and earth work for drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1. (c) Precast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. (d) Funnel with watering pipe of GI 20 mm nominal bore medium grade and copper lugs etc all as specified.

Srl item No 134 Contd … (e) 15 mm nominal bore light grade GI protection pipe 7.5 mtr long for protection of earthing lead from mechanical injury or tempering. (f) Requisite quantity of common salt and charcoal. (g) Testing of earthing. Note : On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of the Engineer-in-Charge.

MADAN LAL SHARMA AND SONS

Alishan Builders

Bansal and Sons

SHIVAE CONSTRUCTION