Maint of footpath, road side furniture, drains, interlocking paths except resurfacing in OTM Accn in Old Cantt Prayagraj.

Amount

Dismantling of timber scantling 40 sqcm over in section in any position as in framed work, complete all as specified and directed.

Demolition of cement Concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation, etc. or for shafts, wells, esspits, manholes, pier holes, etc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed .

Removing excavated material (soil) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed .

M&L for PCC 1:2:4, type B-2 (using 40mm graded stone aggregate) as in pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) etc. complete all as specified and directed

M&L for structural steel framed work (fabrication and fixed in position) using rolled mild steel sections like tubes (square or circular), hollow sections (HSS),Channels (ISMC), angle (ISA) ,flat iron (FI) mild etc as in curved parking shed of approved design and pattern including necessary cutting, crimping, bending to the required radius, drilling, welding or screwing with and including bolts, nuts, washers, as directed and painting on steel surface with two coats of synthetic enamet paint over a coat of red oxide zinc primer complete all as specified and directed. Note : (i) Structural steel sections used shall be conforming to IS:2062 Grade Fe-410. The size of sections and shape their-off shall be as per direction of the Engineer-in-Charge.

M&L for providing and fixing crimped, pre-painted, 0.50mm thick galvalume aluminium-zinc alloy coated steel corrugated roofing sheets (GI base) of approved colour & profile, having a minimum tensile strength of 550 MPa, conforming to IS/ASTM standards, fixed with self-drilling/self-tapping galvanized screws complete all as specified and directed Note : (i) Sheets shall be crimped to suit curved roofing profiles as per design. (ii) cost of EPDM washers, hooks, bolts, nuts, washers, sealant, if required shall be provided by the contractor and cost of the same shall be deemed included in quoted unit rates.

Surface dressing not exceeding 15 cm deep in soft/ loose soil complete all as specified and directed.

M&L for 75mm thick plain cement concrete, 1:3:6, type B2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade of approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., made by table vibratory method using PU mould, over and including 50mm thick compacted bed of fine sand complete all as specified and directed. Note : Paver blocks shall setteled proprly in it's position by vibratory compaction using plate vibrator, filling the joints with sand including finishing and sweeping extra sand. The cost of the shame shall deemed included in quoted unit rates.

M&L for providing and laying cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed wtih cement mortar 1:3 (1 cement 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and directed.

Supply only gavanised iron (GI) PVC coated chain link fencing of approved width, mash size, and wire dia complete all as specified and directed. Note : (i) Fixing shall be measured and paid seperatly under respective item here under as 'fixing only'. (ii) The mass size and wire dia may very as per site requirement from 50x50mm to 100mmx100mm and 3mm to 4mm dia respectivly. (iii) PVC coating over GI wire should not be less than 0.5mmthick i.e the net dia of coated wire shall not be less than GI wire dia Plus 1mm. colour/shade of PVC coating shall be as aproved by Engineer-in-charge.

Supply only mild steel round bar as in line wire for chainlink fancing, mild steel bars 10mm dia and over conforming to Fe-410W (Gde.E-250) quality-A or Fe 290 (Gde -E-165), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed. Note : Fixing of this item shall deemed included in quoted unit rates of item here-in-under.

Supply only mild steel screw bolts (machine made), not exceeding 5cm long and neck dia 5 to 10mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, complete all as specified and directed. Note : Fixing of this item shall deemed included in quoted unit rates of item here-in-under.

Fixing only chain link fencing, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed. Note : Chain link fencing and line wire shall be paid at 'Supplied only' rates under respective item here -in-above.

Dismantling of fencing wire mesh any type complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, embeded in concrete including taking out embedded portion and making good disturbed ground.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for mild steel rolled section angle or tee or flate etc as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 including painting with two coats of synthetic enamel paint over a coat of zinc primer complete all as specified and as directed.

Taking down cat eyes any type and any colour including making the surface finished and smooth as per existing complete all as specified and as directed.

S&F cat eye reflective type in red/yellow/green color of Polycarbonate body, scratch and abrasion resistant, fixing with epoxy/bitumen adhesive as per manufactures instructions complete all as specified and directed.

S&F solar cat eye in red/yellow/green color of aluminum alloy, 100% water proof design according to 65), size 125mm x 125mm x 25mm (shank 65mm), high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. complete all as specified and directed.

Taking down convex mirror any type and any size including making good the disturbed surface finished and smooth as per existing complete all as specified and as directed.

S&F Convex Mirror 1000mm dia, polycarbonate reflective Mirrors, ABS body with hood for outdoor use mounted on 50mm dia stainless steel pipe (304 grade), height not less than 1200mm from groud level including mounting hardware as per manufacturer instructions, grouted in PCC (1:2:4) type B1 and necessary eartwork complete all as specified and directed. Note : (i)Cost of PCC and eartwork deemed included in quoted unit rates (ii) The Post holeexcavated shall be 300x300x750mm and minimum 60mm pipe shall be embedded in PCC. PCC shall be filled up to GL in post hole Make : Aktion / Dark eye/3M

Taking down road side benching made of any material any type & size including making good the disturbed surface finished and smooth as per existing complete all as specified and as directed.

S&F in position Dholpur sandstone bench as per approved drawing, comprising machine-cut, hand-dressed seat slab of size 1800×500×80 mm and backrest slab of size 1800×300×80 mm with moulded edges and polished exposed surfaces, supported on two end legs of 100 mm thick Dholpur sandstone in arch/solid profile grooved to receive the slabs, all components joined and fixed using 1:4 cement mortar (1 cement : 4 coarse sand) matching the stone shade, joints properly filled and finished, and each leg fixed over a plain cement concrete (PCC) M-15 grade block of size 450×450×100 mm using 20 mm graded stone aggregate, complete in all respects as per drawing and as directed by the Engineer-in-Charge.

M&L for Manufacturing, supplying and fixing retro reflective informatray signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue/red/green colour back ground on both sides and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge.

Contd/... Note : Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment purpose.

M&L for Structural steel work using rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc cofrming to F.E 290 Grade E-165 including necessary drilling, making holes for fixing nut-bolts,welding etc, painting with 2 coats of synthetic enamel paint over zinc primer, grouted (02x legs) in PCC (1:2:4) type B1 and necessary eartwork complete all as specified and directed. Note : Excavation , earthwork and PCC shall be measured and paid seperately under respective items.

Taking down solar dealineator any type any size including making good the disturbed surface finished and smooth as per existing complete all as specified and as directed.

S&F metal tubular Solar dealineator made out of ABS round body fitted with 2 Nos 65mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed . Make : Dark eye Modal No :DA 112

M&L for painting the exposed vertical faces of kerb stones in alternate yellow and black bands using approved synthetic enamel paint conforming to IS:2932, applied in two coats over a primer conforming to IS:2074, including preparation of new or previously painted surfaces by thoroughly cleaning, scrubbing, removing existing loose paint, dust, oil, and grease, by wire brushing or other approved means, ensuring uniform finish and sharp colour transition over approximately 150 mm height from road level, complete all as specified and directed.

Dismantling and taking down existing sinage board with frame work (including disconnection of electric connection is any) and making good disterbed surfaces complete all as specified and dirtcted.

Dismantling and taking down existing existing unserviciable tiles/paver blocks, any pattern, discriprion and type complete all as specified and dirtcted.

All as per item No. 35 above but letters of height exceeding 100 mm but not exceeding 250 mm.

S&F ACP sheet as in signage board wall panelling,cladding or ceiling 3 mm thick of approved colour, at a height up to 10m, fixed on mild steel framing or grid with self taped screws including sealing joints with silicon tape complete all as specified and directed.

ANKIT SHIP REPAIRERS AND SUPPLIERS (BID ID -3468776)

vs construction (BID ID -3467337)

LOKESH CONSTRUCTION (BID ID -3468359)

ms shanti sons (BID ID -3468683)

M/S ATUL CONSTRUCTION (BID ID -3468278)