SPL REPAIR TO OR MD ACCN BLDG NO T-15 (06 QTRS) AT OLD MH LINES AND SPECIAL REPAIRS TO ALL CULVERT, PATH AND DRAINS (04 NOS OF CULVERTS APPROX SIZE DRAINS 340 MTRS) IN UNIT AREA AT OD COMPLEX UNDER GE (EAST) MATHURA

Amount

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall covering fixed with self tapping screws complete.

Dismantling of timber scantlings 40 Sqcm & over in section in any position in framed work in fillets rails posts rafters purlins in framed work

M&L for Mild steel work in tubular trusses, purlins, vetical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-2979 grade ST-240.

Demolition of reinforced concrete (cutting reinforcement) as required to facilitate demolition of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, cover slab etc complete all as specified.

M&L Use & waste of steel Form work to soffits of suspended slabs such as roof slabs floor slab landing and similar work for flat rough finished surface complete all as directed.

M&L for RCC M-25 grade (Design Mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like & similar RCC works all as specified and directed.

M&L for steel reinforcement of TMT bars (FE-500 Grade) 10 mm dia and over cut to length and bent to shape required including cranking bending spirally for hooping for columns hooking end and binding with mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips all as specified and directed.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified.

Taking down cement or cement lime plaster on brick or stone walls, etc. including racking out joints,hacking for key,scrubbing down with water, etc.

M&L for rendering 15 mm thick on other than fair faces of brick wall or concrete surface in cement mortar 1:6 finished even & smooth all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of cement base paint including preparation of surface of wall including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for rendering 15 mm thick on brick wall or concrete surface in cement mortar 1:4 finished even & smooth without using extra cement including using water proofing compound but excluding the water proofing coompoung all as specified and directed. Note:-Water Proofing compound will be measured and paid separately.

Supply only liquid water proofing compound hydroseal-W+ / Dr Fixit or eqivalent (for plaster hardening, to contol efflorescence & fungal growth) as approved by GE.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), rubbish off the premises.

M&L for 25 mm thick cement concrete type M-15 grade (Nominal mix) using 20 mm graded stone aggregate as in levelling course complete all as specified.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified.

M&L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified.

M&L for Glazed ceramic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick backing coat of cement mortar in 1:4 complete all as specified.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar.

M&L for 20 mm thick Granite slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in 20 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. including rounded/half rounded edge and hole for gas pipe in pre-cast slab as well as stone slab in cooking platform complete all as specified

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified.

M & L for 50 mm thick plain cement concrete 1:3:6, type C1 (using 20 mm graded stone aggregate) as in plinth protection surfaces finished even and smooth without using extra cement including filling the joints by bitumen and sand mixed in the ratio 1:4 by weight complete all as directed.

M&L for 100 mm thick cement concrete M-7.5 grade (Nominal mix) using 40 mm graded stone aggregate as in sub base complete all as specified.

M&L for 25 mm thick Sand filling under floors or in foundations including watering and consolidation.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade made with grey cement and pigment complete all as specified and directed.

M&L 10 mm thick non skid coloured ceramic ENDURA tiles n. exc. 0.11 sqm set and jointed in neat cement slurry & pointed with coloured cement to match in floor over including 15 mm thick screed bed in CM 1:4 .

Dismantling boarding, any description, fixed in any position complete all as specified and directed.

Providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications and as directed by Engineer-in-charge.

M&L for 4 mm thick Non asbestos fibre cement building boards fixed or laid on GI framework fixed in ceiling complete all as specified. Make: Everest or equivalent approved makes

Taking down Chowkhats or frames with shutter without taking off shutters from the frames not exc. 1.5 sqm each.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames exc. 1.5 sqm but n exc 4.00 Sqm each.

S&F powder coated Aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

M&L for powder coated aluminium window shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

M&L for providing powder coated aluminium ventilator, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F 4.00 mm thick Figured glass, pin head type and glazing in squares n exc 0.5 sqm in each pane

S&F 5 mm Sheet glass,ordinary quality and glazing in square n exc 0.5 sqm in each pane

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet PVC sheet reinforced with M.S. square tube,supplying & fixing in opening as per specification & drawing complete all as specified.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified.

M&L for Pressed steel frames 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S&F 105x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc complete all as specified and fixed

M&L cement concrete M-10 grade (Nominal mix) using 20mm graded stone aggregate as in blocks for fixing hold fasts and fillling of chowkhats or any other purpose all as specified.

M&L for applying two coats of synthetic enamel paint on primed steel surface complete all as specified.

S&F IInd class Hard wood 30mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.

S&F 35 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides.

M&L for prepration of new wooden surfaces, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed by Engineer-In-Charge.

Supply and fix Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

Supply and fix 250 mm long Stainless steel, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts complete all as specified.

Supply & fix 150 mm long Stainless steel handles fabricated type all as specified.

Supply & Fix 200 mm long Stainless steel barrel tower bolts of section and fixed.

Supply & fix 100mm long Stainless steel hinges with galvanised mild steel hinge pin, and fixed, type B-21

S&F in repair 25 mm dia, stainless steel curtain rod 304 grade with fixing brackets, stops, rollers, end caps etc.complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Taking up or down 15 mm bore of dia steel tubing and connections, including cleaning for refixing or removal to store.

Taking up or down 20 mm bore of dia steel tubing and connections, including cleaning for refixing or removal to store.

Taking up or down 25 mm bore of dia steel tubing and connections, including cleaning for refixing or removal to store.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth of brick walls complete all as specified.

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

Supplying & fixing to walls and ceiling 25 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

S&F Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC Flush pipe complete including jointing to socket of flushing rim all as specified and as directed.

S&F in repair 15mm dia bore chromium plated Stop valves/Angle cock cast copper alloy,screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm including including 15 mm Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure complete all as specified and as directed.

S&F in repair bib cock 15 mm bore chromium plated cast copper alloy with screwed down, screwed for iron pipe or for brass ferrule and fixed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm.

Supply and fix in repair chromium plated Swivel shower of PTMT any colour for fixing with 15mm pipe.

Supply and fix in repair chromium plated Shower arm 15 mm size, 195mm long with bend of 45degree with flange of any colour.

S&F 32 mm dia Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 laid in trenches

Supply and fix in repair Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats.

S&F in repair Sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

S&F in repair stainless steel kitchen plate rack of size 775x750x250mm deep, fabricated with 0.63 mm thick sheet fixed in position on wall complete. Make:- Prayag cat No P-346 or equivalent make specified in Appx 'B'

Dismantling water tanks exc 500 ltrs and n exc 1000 ltrs complete all as specified and as directed.

Supply and fix 1000 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete.

S&F in repair 20 mm dia Gun metal, globe or gate valves,with iron wheel head,screwed both ends for iron pipes and fixed.

S&F in repair 75 mm dia PVC floor trap plain with grating including jointing with solvent cement complete all as specified.

S&F in repair110 mm dia PVC (SWR) bends any radius with oval access door complete all as specified.

S&F in repair 75 mm dia PVC (SWR) bends any radius complete all as specified.

S&F in repair 110 mm dia PVC(SWR) plain bends any radius complete all as specified and directed.

S&F in repair 110mm PVC (SWR) WC connector with lip ring to fit wc outlet complete all as specified.

S&F in repair PVC (SWR) junction single T with access door bore 110 mm complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm dia pipes type 'A' single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

S&F in erpair PVC (SWR) 110 mm dia pipes type 'A' single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

S&F in repair PVC (SWR) 110 mm dia pipes type 'A' single socketed, in any length with rubber ring joints, fixed on walls complete all as specified.

S&F in repair PVC (SWR )vent cowl complete all as specified.

M&L for 18/19 mm thick Block boards, grade 2 quality,interior grade, commercial type, fixed with screws to timber frame-work as in cupboard/kitchen cupboard complete all as specified.

M&L for 0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instruction

S&F 150 mm Brass handles, cast type, polished bright complete all as specified.

S&F 75 mm Aluminium anodised, barrel tower bolts of extruded section and fixed

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised

S&F 25 mm size Magnetic catches for cupboards including fixing to frame and and connected plate to shutter complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls/ceilings and applying two coats of weather proof acrylic exterior paint (100% Acrylic) over a coat of self primer with spray machine, spray hard to reached area to achieve excellent application using limited manpower including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed. Note :- (i) Weather proof acrylic exterior paint shall be applied machincally by latest machine such as trucare Graco or equivalent having minimum pursue of 3300 PSI.

M&L for preparing newly plastered surfaces of walls and applying two coats of oil bound distemper with spray machine, spray hard to reached area to achieve excellent application using limited manpower over a coat of primer and applying wall care putty not less than 1mm thick complete all as specified and as directed. Note :- (i) Oil bound distemper shall be applied machincally by latest machine such as trucare Graco or equivalent having minimum pressure of 3300 PSI.

M&L for preparation of old plastered surface of wall and applying one coat of distemper oil emulsion complete all as specified.

M&L for obliterating old writing building number with synthetic enamel paint n.exc 0.10 Sqm and match the existing work including preparation of surface all as specified

Writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil

Removing excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

M&L for 75mm thick cement concrete M 7.5 grade (Nominal Mix) using 40mm graded stone aggregate as in sub base flooring complete.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 100 mm thickness M-50 Grade made with grey cement and pigment complete all as specified and directed.

M&L cement concrete M-15 grade (Nominal mix) using 20mm graded stone aggregate as in roof kerbs of mud stops, bed blocks, benching etc including necessary form work complete all as specified and directed.

Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc. ) complete including fixtures & fittings (such as ceiling rose, socket, Pendent, regulator, light fitting etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as directed.

Taking down carefully by Submain wiring/ service connection of any type complete all as directed by Engineer-in-Charge.

M & L for Point wiring with 1.5 Sqmm (nominal area) single core PVC insulated unsheathed (FRLS) cable, multi-stranded, copper conductor in universal colour code with & including suitable size of rigid non-metallic PVC conduit (not less then 20mm dia med gd)and its all accessories complete concealed in wall / roof incl cutting & chases( making good all to the disturbed surfaces as per existing) and modular flush metal boxes suitable for modular fittings including modular cover plate with frame for mounting modular switches, sockets, etc including earth wire of PVC insulated (FRLS) copper conductor multistranded of 1.5 Sqmm size in green colour complete all as specified in current SSR Part-I & II & directed by the Engineer-in-Charge , as described below:-

One light point controlled by one way switch 5 amp complete.

One ceiling fan point controlled by one way switch 5 amp and one regulator complete.

One exhaust fan point controlled by one way switch 5 amp complete.

One 3 pin 5 Amps socket point controlled by one switch on same board.

One 3 pin 5 Amps socket point controlled by one switch on independent board.

One bell point controlled by one push button on independent board

All as per item No. 109 but for 3 pin / 5 pin 16 Amps sockets outlet with 4 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent complete all as specified and as directed .

M & L for Cable TV Point wiring with RG-06 (foam), electrolytic grade solid annealed Copper conductor,Jelly Field, Aluminium Foiled and Aluminium wire Braided as per ISI marked including suitable size of rigid non-metallic PVC conduit (not less then 20mm dia medium grade) modular flush metal boxes available and suitable for modular fittings, concealed type, covered with modular plates for mounting modular TV sockets etc as directed by the Engineer-in-Charge .

M & L for Sub Main Wiring with two runs single core 4 Sqmm PVC insulated unsheathed (FRLS) cable with stranded copper conductor drawn in suitable size of rigid non-metallic PVC conduit and its all accessories complete concealed in wall/roof with and including 4 Sqmm copper green colour earth wire all as specified and directed by Engineer-in-Charge. Note :- Two run 4 Sq mm single core cable, one run of 4 Sq mm earth wire & One run of PVC conduit shall be measured as one unit length.

Supply and Fixing fancy ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified.

Supply and Fixing Modular switch 6 Amps single pole one-way, 1 Module complete all as specified.

Supply and Fixing Modular bell Push switch 6 Amps with indicator single pole one-way, 1 Module complete all as specified.

Supply and Fixing Modular switch 16 Amp single pole one way, 2 Module all as specified.

Supply and fixing Bell Multi Music type, 230 Volts complete with connection all as specified & directed.

Supply & Fixing Modular fan Regulator electronic step type 120watt , 2 Module complete all as specified.

Supply and fixing fancy Lamp holder, PVC / polycarbonate type with back plate suitable for batten fittings complete all as specified.

Supply and Fixing Modular socket 2-in-1, 5 pins 6 Amps , combined 2 Module complete all as specified.

Supply and Fixing Modular socket 2-in-1,3 and 5 pins 6 /16 Amps, combined 2 Module complete all as specified.

Supply and Fixing Modular TV cable socket , 1 Module complete complete all as specified.

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1x 20 watt LED Tube fitting with polycarbonate channel housing, 140V-270 volts and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge. Make:Havells (as per Cat Part No: LUMILINEBS20WLED 865 SPC WH) or equivalent to CG/Bajaj/Philips/ syska

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1x 9 watt LED Tube fitting suitable for mirror light with polycarbonate channel housing, 140V-270 volts and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge. Make:Havells (as per Cat Part No: LUMILINEBS9WLED865 SPC W H) or equivalent to CG/Bajaj /Philips / syska

Supply and Fixing Surface /Ceiling mounted downlight 1 X 10 Watt LED complete fitting with all accessories internally pre-wired ,,energy efficient, 140V-270 volts and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge. Make:Havells (as per Cat Part No:INTEGRANEOSURFA CEDLS10WLED857S) or equivalent to CG/Bajaj /Philips / syska

Supply & fixing decorative Wall light fitting made up of Polycarbonate with outer cover shape having Glove / Mars suitable for B-22 base holder with 10 Watt LED lamp complete with all accessories and including connection complete all as specified and as directed. Make : Havells (as per Cat Part No MARS Shape - :LHFOFWE1TZ1W012 9405) or equivalent to Philips / Bajaj / CG / syska

Supply and fixing surface mount type bulk head LED fitting 10 Watt complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of complete all as specified and as directed. Make: Havells ordering cat part No HEXAFT10WLED 857SSY MBOPC or equivalent in Bajaj/ Philips/ Wipro /CG/ syska

Supply and fix LED 10 W , 5 Star rated lamp suitable for normal holder( Base Cap B22) complete

Taking down old unserviceable existing SPN / TPN DB / enclousers any size and type / any descriptions as iron sheet scrap including MCB any type / size and making good disturbed surface / wall as per existing complete all as specified and directed

Supply & fixing MCB distribution board, SPN 8 Way, Double door type with Copper bus-bar 200Amp, neutral link, earth bar and din rail , cable ties for cable management, 240 V, complete all as specified.

Supply & fixing MCB SP 6 - 32 Amps, 'B' series, bracking cap10KA

Supply & fix MCB SPN 40 Amps, 'C' series , bracking cap10KA, 240V

Supply and fix modular power socket 16 Amp unit protected with 16 Amp SP MCB including with sheet enclosuer complete all connection as directed. Make : Havells as per Cat Part No DHDMCSN0251016 or equivalent of Legrand /L&T

Supply and install of 30W LED building security light fitting with lens & driver, IP-65 proction with luminaire efficiecy of greater than 80Lumen/Watt, including all connections complete all as specified. Make of fitting : Havells (as per Cat Part No : ENDURACITYLITEPLAT PLUSSL30WLED757SASYBOPC) or equivalent in Crompton Greaves/ Bajaj/Philips / C&S/ Syska

M&L for building security light bracket made out of 40mm dia medium grade GI pipe of 1.2 m length bent to required shape suitable for fixing security light fitting on wall including two Nos clamps complete all as directed by Engr-in-Charge.

Taking down electric meter from location and refixing the same on LT panel box / wall including with mounting box with nut, bolts, suitable thimbles including making connection complete as specified.

Taking down the ceiling fan including down rod of any sweep carefully from its installed position, dismantling complete for repair & servicing , greasing / oiling and including replacement of unserviceable parts like Bearing, Capacitor, Rubber wheel bush , Nut -bolts, split Pin, hanging clamp with nut & bolts and painting of fans , writing MES No. complete and hanging / refixing in position after civil work complete all as directed.

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete. Note : GI wire 4mm dia earth lead upto 7.5 mtr beyond the edge of earthpit shall be deemed to be included under unit rate quoted.

Taking out the electric geyser of capacity 25 Ltrs Ltrs carefully from its installed position by disconneting inlet and outlet water pipes, dismantling the unit and replacing the defective heating element, indication lamps and painting with one coat of synthetic enamel paint and witing MES No.and refixing in its original position and reconnecting the inlet/outlet water pipes and testing on completion complete all as directed by Engineer-in-Charge. NOTE:- The spare parts required shall be measured and paid separately under relevant items.

Supply only the following items suitable for electric geyser of capacity 25 Liters:-

Heating element 1.5 / 2 KW ISI marked including rubber Gasket as per existing type

Thermostat suitable for 25 Ltrs Geyser (as per the existing type)

Hot water / cold water pipe 600mm long as per existing type

S&F TP&N Vertical Loadline distribution board, 4 Way, Double door, with Copper bus-bar 200Amp, neutral link, earth bar and din rail ,440 V, 4 way complete all as specified including fitting with following MCCB & MCBs with connections :-. (i) MCCB 100 Amps, 4 Pole, 16 KA - 01 Nos (ii) MCB SPN 32-40 Amps - 06 Nos

Supply and fix exhaust fan 300mm sweep Mettallic type alongwith louvers complete suitable to work on AC, single phase, 230 Volts, including taking down old unserviceable rusted exhaust fan any type . Make : Havells -Model Ventil Air DB and equivalent of Bajaj / Crompton greves / Orient

Supply and fix exhaust fan 200mm sweep non metallic type alongwith louvers / front grill complete suitable to work on AC, single phase, 230 Volts, including taking down old unserviceable rusted exhaust fan any type . Make : Havells -Model Ventil Air - DX White and equivalent of Bajaj / Crompton greves / Orient

Supply, laying and testing Service line UG cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sq mm 4 core including passing through with HDPE DWC pipe (size not less than 40m outer dia & 32mm innner dia) for protection of cable with laid in trenches / duct / fixing on walls / poles with suitable fixing clamp including connecting with suitable lugs, thimble, glands, nuts and bolts and testing complete all as directed by Engr-in- Charge . Note : DWP HDPE pipe shall be deemed to be included under unit rate quoted.

Excavation in trenches in any type of soil not exceeding 1.5 mtr in depth and not exceeding 1.5 mtr wide for laying of cables and getting out including all as specified and as directed by Engr-In-Charge.

Returning, filling in including spreading, levelling,watering and well ramming excavated soil in layers not exceeding 25 cm thick each , filling back in trenches after cables have been laid and tested complete all as specified.

Material & labour for removing the defective ceiling fan winding upto 1400mm sweep and rewinding with super enamelled copper wire of existing gauge, applying insulation varnish, pre heating and binding with empire tubes, crimple sheet etc. as required for rewinding complete all as specified and directed by Engineer-in-charge.

M/S SHRI RAM INFRASTRUCTURE

B S ENTERPRISES

M/S PREETI CONSTRUCTION

BHARDWAJ CONSTRUCTIONS

SHRI RADHAYSHYAM JHA

M/s Singh Engineering Corporation

M/S HAJI BUILDERS

JWALA ELECTRIC CONTRACTORS