SPECIAL REPAIR TO BLDG NO SM-204 AT DENNIS ROAD UNDER GE (MCTE) MHOW

Amount

B/R WORK

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 sqm and not exc 4 Sqm each complete all as specified and as directed.

Resecuring or easing and adjusting door shutters of size exc 1 sqm and not exc 2 sqm each of any description without taking down shutter from frame complete all as directed.

Dismantling boarding of any description fixed in any position with screws

Demolition of stone, brick masonry built in cement mortar incl quoins, arches, etc but exceeding ashlar facing dressed stone Work etc.

M&L for Brick work with sub-class 'B' burnt bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and as directed.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

S&F Solid single PVC door frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet reinforced with M.S. tube, edges will be painted to match with prelam sheet suppling & fixing in opening as per specification & drawing including all fixtures shown on drawing complete all as specified and as directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M S frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail; stile &rails having one side feathered edge and on other side 10mm 90^0 bent edge, Paneling of 2mm thick prelam PVC sheet on bothfaces i.e front face & back face with particle board core to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, and including all hardware necessary for a door supplying & fixing in the frame at site as per specification & drawing.given in SSR 2020 complete all as specified and as directed.

S&F pressed steel door frames of size 125 x 60mm, made of 1.25mm thick sheet, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified as directed.

S&F Factory made, 35mm thick 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35mm thick complete, all as specified and as directed.

S&F Factory made, 2nd class hard wood, 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass/ gauge etc. (without sash bars) edges or framing plain, chamfered or rounded fitted with cut or mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I section 8.20 (a), all as specified and as directed.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required : hooks (stay), heavy, for large gates; hook and pintle hinges : large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; complete all as specified and as directed.

M&L for PCC 1:3:6 Type C1(20mm graded aggregate) as in bed block for holdfast and filling door frame.

S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F 250mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F 100mm size of Butt hinges, medium weight cold rolled mild steel complete door etc

S&F aluminium anodised barrel tower bolts of extruded section with 100mm long bolt, all as specified.

S&F aluminium anodised barrel tower bolts of extruded section with 200mm long bolt, all as specified.

S&F aluminium anodised barrel tower bolts of extruded section with 150mm long bolt, all as specified .

S&F Extruded aluminium alloy handles fabricated type anodised 150mm size complete all as directed and specifiedand as directed.

S&F Extruded aluminium alloy handles fabricated type anodised 100mm size complete all as directed and specified and as directed.

M&L for floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, 140mm long, fixed in floor complete all as specified & as directed.

S&F hasp and staple 125mm, safety type, aluminium anodised with alu hinge pin incl bolt to hinge plate and fixed with screws all as specified and as directed.

M&L for preparation of new steel or iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, comlete all as specified and as directed.

M&L for preparation of new wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of filler coat with grey filler or liquid wood filler, transparent, and bringing forward surfaces to smooth even finish, comlete all as specified and as directed.

M&L for stainless steel wire cloth, 0.71mm nominal dia of wire and average width of aperture 1.20mm and fixed with tinned tacks, or stainless steel wire staples complete as all as specified and as directed.

S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

S&F powder coated aluminium window and ventilator shutter, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.) complete all as specified and as directed.

M&L for 4mm thick sheet glass ordinary quality in panes exec 0.5 sqm each fixed with & including rubber gasket in alu frame work complete all as specified and as directed.

S&F framed work such as grills, gantries etc with ends of bars shouldered and or riveted or forged into spikes, framed gauged bars bared iron doors, ladders framed ballusters, walk ways, railings framed works of water Tanks and similar works confirming to Fe 410-0 or Fe 310-0

S& F 18mm thick factory made PVC sheet one side pre laminated sheet kitchen cabinet shutter/ cupboard shutter. The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for making edge lipping bending for 0.5mm thick PVC sheet lipping at all four edges using bodning etc complete all as specified and directed by Engr-in-Charge.

S&F factory made PVC shelf/ partition of required size consisting of panel of 12mm thick celuka PVC ply and for supporting the hold of shelf/ partition and shall provide 3 edges in size 18mm x 18mm as per required length the front side of the edge visible in the fronth of the self/ partition to be edge lipped by 18mm width x 1mm thick PVC sheet of density 600kg/cum manufactured by ISO 9001-2015 Certified company using solvent cement etc complete all as specified and as directed.

S&F 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and as directed.

S&F Stainless stell self closing hinges for PVC doors shutters complete all as specified and as directed.

S&F repair stainless steel curtain rod brackets 25mm dia including necesary SS clamp complete all as specified & as directed.

Demolition of cement concrete (including floor tiles, kota stone flooring etc) (un-reinforced) of any description and in any position not otherwise specifically provided for incl removing the demolised materials to a distance exc 50 mtr and not exc 100 mtr complete all as specified and as directed.

M & L for 75mm thick cement concrete 1:3:6, type C1, with using 20mm graded stone aggregate in floor/ plinth protection, finish the surface even and smooth without using extra cement including forming constructions joints and filling the same with bitumen filler complete as specified and directed.

M&L for forming construction dummy joints 65mm deep x 10mm wide fillied with Grade B sealing compound complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing debrish and rubbish of the premises and stacking serviceable tiles.

M&L for scratch free, doubly charged, vitrified ceramic tiles 10 to 12mm thick (square or rectangular) area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for Non Skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for Glazed Coloured ceramic tiles (textured and designed as required) in vertical surfaces size 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick backing coat in CM 1:3 complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20-25mm thick laid over and including 20mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigments to match the shade of the slab including rubbing and mirror polishing with beeswax polish complete all as specified and as directed.

M&L for Mirror polish on old kota stone floor wherever required to give high glossy finish complete all as specified and as directed.

All as per item No.46 here in before but as in skirtings

M&L for granite slabs 20mm thick machine cut bedded laid over & incl cement Mortar 15mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl grinding moulding rounding chamfering and polishing complete all as specified.

Rounding to edges of stone slab one edge such as in steps, cooking platform, and other similar situation complete all as specified

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed.

S&F Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F Vitreous China wash basin, angle back, size 550 x 400mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S&F in repair 25mm dia Gun-metal, golbe or gate valves, with iron wheel head, screwd both ends or iron pipe and fixed complete all as specified and as directed.

S&F in repair 20mm dia Gun-metal, golbe or gate valves, with iron wheel head, screwd both ends or iron pipe and fixed.

S&F angular Stop valves, cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Make : Cat Part No. COP-057PM of Jaquar or equivalent approved by the GE.

S&F Long body CP Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. Make : Cat Part No. CON-107KN of Jaquar or equivalent approved by the GE.

S&F Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. Make : Cat Part No. CON-037KN of Jaquar or equivalent approved by the GE.

S&F Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed. Make : Cat Part No. CON-273 KNUPR of Jaquar or equivalent approved by the GE.

S&F chromium plated shower roses 125mm sizes with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed. Make : Cat Part No. OHS-1667 of Jaquar or equivalent approved by the GE.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F PVC mirror cabinet complete all as specified and as directed.

M&L for Health faucet (ABS Bpdy) mild steel chromium plated suitable for 15mm dia pipe 1.25 M long flexible tube and ABS wall Hook including making connection and fixed in position complete all as specified and as directed. Make : Cat Part No. ALD-565 of Jaquar or equivalent approved by the GE.

Taking down old GI tubing ISI marked medium grade 15mm bore with all fittings including connection etc, complete all as specified.

Taking down old GI tubing ISI marked medium grade 20mm bore with all fittings including connection etc, complete all as specified.

Taking down old GI tubing ISI marked medium grade 25mm bore with all fittings including connection etc, complete all as specified.

M&L for GI tubing ISI marked medium grade 15mm bore with all fittings and fixed complete to walls and ceiling or laid under floor including connection etc, complete all as specified.

M&L for GI tubing ISI marked medium grade 20mm bore with all fittings and fixed complete to walls and ceiling or laid under floor including connection etc, complete all as specified.

M&L for GI tubing ISI marked medium grade 25mm bore with all fittings and fixed complete to walls and ceiling or laid under floor including connection etc, complete all as specified.

Cutting chases for concealed water tubing in brick wall and making good in CM 1:3 cutting n.exc 10cm girth.

S&F in repairs incl hoisting HDPE plastic water cylindrical vertical type tanks closed top of capacity 500Ltrs incl 20mm bore brass stop cock and 20mm bore brass float valve with polythene float complete all as specified and as directed.

M&L for 25mm dia Ball Brass valves high pressure with polythene float and fynut complete screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm and including waste pipe complete all as specified and as directed.

M & L for steel plate rack of size 900 x 750 x 250 made up of 1mm thick steel complete all as specified and as directed.

S&F in repair CP Toilet paper holder, complete all as specified and directed by Engineer-incharge. Make : Cat Part No. ACN-1153 of Jaquar or equivalent approved by the GE.

S & F in repairs PVC (SWR) Floor trap/ Nahani trap plain or multi with stainless steel grating incl jointing to waste pipe with solvent cement joint dia of outlet 75mm bore complete all as specified and directed.

S & F in repairs 110mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trench complete all as specified and directed.

S & F in repair 110mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed.

S & F in repair 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

S & F in repair 75mm bore PVC (SWR) vent cowl complete all as specified and directed.

S & F in repair 110mm bore PVC (SWR) bend any radius complete all as specified and directed.

S & F in repair 110mm bore PVC (SWR) bend with acess door complete all as specified and directed.

S & F in repairs 75mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trench complete all as specified and directed.

S & F in repair 75mm bore PVC (SWR) bend any radius complete all as specified and directed.

S & F in repair 75mm bore PVC (SWR) bend with acess door complete all as specified and directed.

S & F in repair 75mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed.

Dismantling of cast iron/ PVC pipes jointed in cement mortar 110 / 75mm bore all as specified and directed

S&F 75mm bore PVC reducers PVC (SWR)

S&F 110mm bore PVC reducers PVC (SWR)

S& F in repair 40mm Bottle trap of PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms/ 40mm-270 gms)

S&F in repair Waste coupling of 40mm dia PTMT (half or full threaded). (Minimum weight 32mm-45gms/40mm-60 gms) fixed in repair complete all as specified and directed.

S&F PVC waste pipe fixed to any type of coupling of 40mm threaded complete all as specified and directed.

M & L for provide PVC spout pipe of 25mm bore & 45cm length in sunken floor including cutting holes in brick walls built in cement mortor and making good the dismantled portion in PCC (1:2:4), type B1 with using 20mm graded stone aggregate with wall finish at the disturbed portion of external surfaces complete all as specified and directed

S&F Chromium plated jet for EWC with 1.00 Mtr long PVC pipe including necessary GI fitting as required like toe nipple etc complete all as specified and directed

S&F in repair CP WHB mixer for mixing hot & cold water screwed down for iron pipe 15mm bore complete all as specified and as directed. Make : Cat Part No. CON-167KNB of Jaquar or equivalent approved by the GE.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc.

M&L for 15mm thick cement plaster in cement mortar 1:6 on brick or concrete surface etc. on wall finished even and smooth without using extra cement, all as specified.

M&L for rendering 15mm thick in CM 1:4 on brick or concrete surfaces finished even and smooth without using extra cement all as specified incl mixing with water proofing compound (WPC shall be measured and paid separately).

M&L for 10mm thick cement plaster in cement mortar 1:3 on brick or concrete surface etc. on in ceiling finished even and smooth without using extra cement, all as specified.

Complete Removal of Existing tretment on internal surfaces of walls including washing rubbing down and stopping of distempered and painted surfaces

M&L for preparation of new plastered surfaces of walls and provision of 1mm thick wall care puttyand applying a coat of primer chalk whiting on new plastered surfaces of walls and applying two coats of oil emulsion distemper complete all as specified and as directed.

Preparation of old plastered surface of walls and provision of 1mm thick wall care putty and applying a coat of primer chalk whiting on old plastered surfaces including two coats of oil emulsion distemper on wall surface complete all as specified and as directed.

Complete Removal of Existing tretment on ceiling surfaces including washing rubbingdown and stopping of distempered and painted surfaces complete all as specified and as directed.

M&L for prpeparation of old plastered surfaces of ceiling and provision of 1mm thick putty and applying chalk whiting primer on new plastered surfaces ceiling and applying two coats of oil emulsion distemper complete all as specified and as directed.

Complete Removal of Existing tretment on External surfaces of walls including washing rubbingdown and stopping of cement based painted surfaces complete all as specified and as directed.

M&L for preparation of new plastered surface of wall and applying two coats of Anti fungal weather coat acrylic emulsion paint over a coat of primer complete all as directed and specified.

M&L for preparation of old surface of wall and applying two coats of Anti fungal weather coat acrylic emulsion paint over a coat of primer complete all as directed and specified.

Supply only liquid water proofing compound.

Dismantling of plain or corrugated steel sheeting any gauge, thickness, including nainaital or similar pattern roof coverings.

M & L for cutting holes in brick walls built in cement mortar at the starting point of down take soil/ waste pipe at any floor, fill the joint of down take pipe & trap with thick mortar in CM 1:3 and making good the dismantled portion in PCC (1:2:4), type B1 with using 20mm graded stone aggregate with wall finish at the disturbed portion of external surfaces complete as directed and specified.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.11611979 grade St.-240 complete all as specified and as directed.

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise described complete all as specified and directed.

Use & waste of Formwork to sides and soffits of coping beam finished surfaces.

M&L for mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for RCC 1:2:4 type B1 (20mm graded aggregate) as in Chajjas & roof slabs complete all as specified and as directed.

M&L for taking down existing waterproof treatment of tar felt of any description from roof surface and removing rubbish to a distance not exc 100 mtrs complete all as specified and directed.

M&L for PCC 25mm thick (1:2:4) type B0 using 12mm graded stone aggregate mixed with integral waterproof chemicals PIDI PROOF -LW mixed in proportion of 200ML/ 50KG cement of DR fixit of piddilite industries Ltd of STP No 1 (Liquid) of STP Ltd inproportion 200ML/ 50Kg cement as in padding on roof surface for correcting/ making proper slope on roof/ chajja and roof kerbs/ benching complete all as specified & as directed.

M & L for rendering 10mm thick in cement mortar 1:3 mixed with integral water proofing compound while concrete surface is green and finish the surface even and smooth without using extra cement all as specified and directed (WPC shall be measured and paid separately under respective item).

M & L for preparation of surfaces for applying bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm complete.

M & L for applying a tack coat of Industrial bitumen grade of 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces (1st coat for bonding material below membrane and 2nd coat on top of membrane).

M & L for 3mm thick APP based polymeric membrane minimum weighing 3kg/sqm and reinforced with polyester non wove fabric (wt. not less than 150 gms/ sqm) and on primed surface by forced application complete all as specified and directed with testing & 10 years of gaurantee. Note : Application of APP membrane must be done by authorized applicator of membrane manufacturer approved by GE.

M&L for water proofing on roof/ parapert with the following steps with testing & 10 years of gaurantee:- Step I : To clean the existing surface of the roof and making the surface dust free. Step II : Opening of the crack in V groove more than 0.5mm and filling with Epoxy mortar. Step III : Initial Coat (mixed 1/2 Ltr of water in 1 ltr of Roof seal of Asian Paint/ Pidilite/ STP/ FOSROC/ ACC/ L&T/ MARUTI Dr. FIxit as a primer (area cover 1 litr = 9 to 10 sqm) Step IV : After six hours of primer apply first coat (one coat) of Asian Paint/ PIDILITE/ STP/ FOSROC/ ACC/ L&T/ MARUTI Dr. Fixit roof seal in a particular direction without mixing of water. Now left it for six hours (area cover = 1 ltr = 1.2 sqm) Step V : After six hours of first coat apply the second coat of Dr. Fixit Roof seal in other direction without mixing of water (area cover 1 ltr = 1.2 sqm). Now left it for 24 hrs complete all as specified and as directed. Note : The work of waterproof treatment shall be got executed through expert team of manufacturers of authorised applicator of manufacture. Make : Asian Paint/ Pidilite/ STP/ FOSROC/ ACC/ L&T/ MARUTI Dr. Fixit approved by the GE.

M&L for applying two coats of bitumen based aluminium painting @ 0.15 Kg/ sqm each coat on water proofing treatment with preparation of surface as on non assessable area complete all as specified and directed.

M&L for cement concrete 25mm thick type B-1, 1:2:4 (12.5mm graded aggregate) as in roof top etc complete all, as specified and directed by Engr-in-Charge.

M&L for Cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry as on roof surface with grey cement and pigments, and cut and polished etc incl 15mm thick cement plaster in CM 1:4, complete all as specified and as directed

M & L for repair to sunken floor by providing water proofing treatment with testing & 10 years of gaurantee to sunken floor surfaces of RCC slab by the following specifications as specified and directed :- (a) Provide PCC 1 : 1.5 : 3 type A with using 12.5mm graded stone aggregate in slope of average thickness 50mm on sunken floor slab mixed with and including integral water proofing compound manufactured by Dr. Fixit or equivalent as approved, finish the surface even & smooth without using extra cement. (b) Rendering 15mm thick in CM 1:3 mixed with & including integral water proofing compound on sunken floor and sides of (Vertical surface) sunken portion. (c) Applying surfaces of bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm complete. on complete sunken surfaces of floor & wall and provide necessary connections to soil/ waste pipe from WC/ nahani trap etc including demolition of old sunken complete all as specified and as directed. (d) applying a tack coat of Industrial bitumen grade of 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces (1st coat for bonding material below membrane and 2nd coat on top of membrane) (e) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/ sqm) and on primed surface by forced application complete all as specified and directed. (Note : Floor Area shall be measured for payment).

E/M WORK

Taking down copper/ aluminium point wiring (light, fan, bell, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendent, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Taking down existing ceiling fans any size in position and re-fixing the same after B/R work including painting of the same with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and writing MES Number in black paint with skilled painter, with and including providing three core flexible copper cable for connection from ceiling rose/ connector complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper/ aluminium Sub main wiring of any size from surface/concealed/ existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Taking down existing Gysers 25 ltr in position and re-fixing the same after B/R work including painting of the same with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and writing MES Number in black paint with skilled painter, with and including providing three core flexible copper cable for connection from Metal clad to Gyser complete all as specified and directed by Engr-in-Charge.

Taking down existing single phase electric energy meter of any capacity after disconnecting all necessary electrical connections and re fixing the same with rectangular wooden box near to V-TPN MCCB Box cairfully after compltion of B&R Work complete all as specified and as directed.

Taking down old/ unserviceable LT indore panel, distribution board by disconnection of electric connection carefully SPN DBs/ TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sqmm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2mm thick, 60mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC FRLSH insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One light point controlled by two, two way switch 5 Amps

(c) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on the SAME BOARD.

(e) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

(f) One bell point controlled by one, bell switch 5 Amps

All as per item No.137 here in before but using 2.5 sqmm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 Amps switch socket cobmination point including necessary running of 2.5 sqmm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

All as per item No.137 here in before but using 4.0 sqmm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 Amps switch socket cobmination point including necessary running of 4.0 sqmm PVC insulated copper conductor FRLSH cable as earth continuity conductor along with wiring and connecting to the common eath dolly. (for AC Point)

S & F for Modular Switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified.

S & F for Modular Switch piano flush type, single pole, two way, and 5/6 Amp single module complete all as specified.

S & F for Modular Switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S & F for for Bell push modular 6 Amps single module complete all as specified.

S & F for Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

S & F for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sqmm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC FRLSH insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm for P and N and one run of 6.0 sqmm earth and one run of PVC conduit will be measured as one unit

All as per item No.155 here in before but using 4.0 sqmm cable

S & F for lamp holder, PVC/ Polycarbonate type with back plate suitabl for batten/ slanting fittings complete all as specified and directed.

S & F for Highly efficient LED Bulbs, 10 watts in B-22 cap complete all as specified and directed.

Supply and fixing Inverter LED batten 20 watts with square profile and polycarbonate channel. Lithium lon battery with charging time 8 hours -10 hours and back up time upto 4 hours. with extruded environmental friendly, energy efficient with three core flexible copper conductor cable of suitable size from ceiling rose complete with all connected accessories all as specified and directed.

S & F for Decorative wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 7 W LED lamp B22 base and including fixing of LED bulb 7 watts complete all as specified and as directed.

S & F for LED 10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed.

S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 01 years from date of installation and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed.

S & F for Energy saving new generation environmental friendly long life versatile pressure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25/ 35 watts with pre wired and necessary mounting arrangements and provision of 2.5 sqmm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer-in-charge.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

Supply and Fix in repairs flush mounting factory made Vertical FP DB, IP-43 Protection -IK 09 with metal double door with 200 Amps rated copper busbar with 2 neutral bar, earth bar and cables ties for cable management fully insulated bus bar with set of wires and door earthing with provision of space for 100-125 Amps MCCB as incomer and SPN/ TP MCBs as out going, 4 way (Optimum 1+12 Module) complete all as specified and directed by Engr-in-Charge.

S&F (in replacement) MCCB 4 pole, 415 volts, in the existing panel/ location and connection with using aluminum lugs complete all as specified and directed for 125 Amps rating, 25 KA breaking capacity complete

Supply and fix MCB SPN 6 to 32 Amps 10 KA, 'C' series including connection with suitable size aluminium/ copper lugs complete all as specified and directed by Engr-in-Charge.

Supply and fix MCB SP 6 to 32 Amps 10 KA, 'B' series including connection with suitable size aluminium/ copper lugs complete all as specified and directed by Engr-in-Charge.

M&L for single pole and earth encolsure with a two pin and earth plug with socket 240 Volts, 50 Hz complete with one single pole MCB SP 20 Amps complete all as specified and directed.

S & F for Modular type TV Socket out let complete all as specified and as directed.

S & F for Modular typeTelephone socket outlet complete all as specified and direced.

Supply & fix plastic body exhaust fan, AC single phase 230/ 240 V of size 250/ 200mm sweep with louver, white in colour including cutting of wall and duly connection with copper wire from ceiling rose etc complete all as specified and directed.

S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20mm dia for telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

Sppply & Laying XLPE insulated, armoured, electric cable of size 35 sqmm 3.5 core with aluminium conductor, 1100 volts grade, laid in trenches, fixed on poles/ walls or passing through pipes including provision of necessary lugs and glands & making necessary connection including taking down old unservicable cable of any core complete all as specified and directed.

Excavating in trenches, in any type of soil not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc and getting out in any type of soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, leveling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply laying and jointing GI pipe 'light grade' 40mm bore in trenches/ under floors or roads/ along poles/ on wall incl clamps for protection of cables incl fittings complete all as specified and directed.

M & L for clean and dry sand (un washed) in trenches incl spreading and levelling for cushioning of UG cable complete all specified and directed. (Note : Punned thickness shall be measured)

M & L for brick size sub class ‘B’ (modular size), laid flat in trenches for protection of cable complete all as specified and directed.

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate No 3 of SSR Part-I including excavation and earthwork in any type of soil/ strata and testing on completion. Note :- GI earth wire 4mm dia and 15mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

M/s Shree Ganesh Traders

Jamna Constructions

GIRIRAJ CONSTRUCTION AND TRADERS

RK CONSTRUCTION

AJIT ENTERPRISES

PREMCHAND BHAWANI SAHAI

sunway associates

M/s. Shubh constructions