SPL REPAIRS TO BLDG NO TFB-26 AT DEMO BTY AND ADDN/ALTN OF KITCHEN IN BLDG NO SM-121 (9 DENNIS ROAD UNDER GE (AWC) MHOW

Amount

M & L for Roughening / taking down existing roof treatment surfaces including plaster over old concrete roof by picking, sweeping clean and washing down with water to remove dust etc. all as specified and directed.

M & L Brushing neat cement slurry with 3 Kg of cement per Sqm for bonding of old concrete surface to new concrete/plaster surfaces complete.

M & L Cutting out cracks to 6 mm wide 'V' section in existing roofs or terrace (if cracks > 2.5 mm wide), cleaning out, wetting, grouting with and including chemical compound SUPER LATEX of DR. FIXIT of PIDILITE INDUSTRIES LTD or SBR LATEX of STP LTD,, water and cement Sand slurry in the proportion of (1:3) by weight mix or as per manufacturers instructions all as specified and directed complete.

M & L PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) mixed with integral waterproofing chemical PIDIPROOF LW of DR FIXIT of PIDILTE INDUSTRIES LTD or STP No. 1 (LIQUID) of STP LTD @ 200 millilitre per 50 Kg per cement, as in padding on roof surface for correcting / making proper slope on roof, and finishing the surfaces fair and even without using extra cement complete all as specified. Note:- Liquid WPC shall be measured and paid separately.

M & L 10 mm thick rendering in CM (1:3) mixed with integral water proofing chemical compound PIDIPROOF LW of DR FIXIT of PIDILITE INDUSTRIES LTD or STP No 1 (liquid) of STP Ltd @ 200 mililitre per 50 Kg cement as per manufacturers instructions over concrete surface and finishing the surface fair and even without using extra cement complete all as specified. Note:- Liquid WPC shall be measured and paid separately.

Supply only liquid water proofing compound.

M&L Water proofing treatment on "Non approachable / non accessible roof" surface (Horizontal & Vertical surfaces) in following sequence through authorized applicator of the manufacturer all as specified and directed complete. (i) Cleaning of new rendered surface properly and drying the surfaces. (ii) Applying a coat of oxidised bitumen based solvent primer @ 0.30 Kg/ Sqm. (iii) Laying 3 mm thick APP modified water proofing membrane with 100 mm over laps sealed and bounded to the surfaces by 'torchon' method. (iv) Applying two coats of bitiminous aluminium pait @ 200 Gram / Sq M (minimum) in two coats.

Demolition of Concrete(reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specially provider for.

M & L for Reinforced Cement Concrete grade M-25(nominal mix) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L for PCC 1:5:10 type E2 (mass concrete) as in suken floor

Dismantling PVC water tanks Exc 250 ltrs but not 500 ltrs including taking down of float valve and removing from site complete.

S&F 1000 Ltrs capacity double layer (ISI marked) rotational moulded polyethylene water storage tanks, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I complete.

S&F in repair ball valve/float ball high pressure of PTMT 20mm with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed minimume weight 210 gm etc all as specified and directed.

Taking up or down existing steel tubing and connection complete for following bore:-

15 mm bore

20 mm bore

Supplying, fixing, jointing and testing galvanised steel water tubing medium grade with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors, complete for the following sizes: -

15mm dia bore

20 mm dia bore

Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) and rubbish of the premisses complete all as specified and directed.

M&L non skid/mat finish ceramic colour tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm (Colour and design of tiles as approved by GE), in floors etc, and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L glazed ceramic coloured tiles size 300mm x 450 mm x 6-7 mm thick (Colour and design of tiles as approved by GE) on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M & L for vitrified cerameic tiles 9 to10mm thick light shade (square/rectangular ) polished, area of each tiles not exceeding 0.36 sqm in floor/skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed in cement mortar 1:6 complete all as specified and directed.

M & L 25 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate including finishing surface of concrete topping even and rough complete as in levelling work etc complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed

M & L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed in cement mortar 1:4 complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet complete.

M&L Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) complete all as specified.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. complete all as specified.

M& L for chicken wire mesh 28 guage for fixing in GI frame work of PoP ceiling complete all as specified and directed.

M & L for Fully Modular kitchen with following spcification: (1) One base unit(below countertop) and one wall unit(above counter top) (2) Base unit:- L= 14ft (approx) with Box height= 850mm (3) wall unit :- L= 8ft (approx) with box height=600mm, partition/compartment will be described by manufacturer/user requirement. (4)Material to be used:- Plywood BWP Grade (IS710) with all faces will be laminated of 1mm thick glossy laminates as per approved shade and other edges as per laminates for Carcass and Shutters of base unit and wall unit. (5) Tandem Drawers:- 4"- 1 nos 6"- 1 nos 8" - 3 nos (6) Cutlery Drawer :- 4"- 1 nos (7) Plate Holder :- 1 Nos (8) Thali Holder :- 1 Nos (9) Pull Out :- 1 Nos (10) Detergent holder and dustbin holder :- 1 Nos (11) All hinges and channels to be soft close type. (12) All handles to be standard G profile type. (13) Pantry Unit :-1 Nos with 6 nos drawer of size 2ft x 2ft. (14) Chimney- Auto clean with sweep capacity of 1300 cum/hr with 5 years warranty of chimney parts and motor and 5 year AMC including fixing arrangement, duct pipe, cooker hood etc complete. Make: hindware, Faber and equivalent. (Description Contd on item No 29.01)

Note: 1. Job will be exfecuted by manufacturer having past experience and it will be approved by GE. 2. Any other part/item not included in the specification above will be deemed to be included in the quoted rates. 3. Manufacturer will make 3D plan for the entire set up and get it approved by GE, prior to execution/implementation

M & L for Fully Modular kitchen with following spcification: (1) One base unit(below countertop) and one wall unit(above counter top) (2) Base unit:- L= 6 ft(approx) with Box height= 850mm (3) wall unit :- L= 4ft(approx) with box height=600mm, partition/compartment will be described by manufacturer/user requirement. (4)Material to be used:- Plywood BWP Grade (IS710) with all faces will be laminated of 1mm thick glossy laminates as per approved shade and other edges as per laminates for Carcass and Shutters of base unit and wall unit. (5) Tandem Drawers:- 4"-1 nos 6"- 1 nos 8" - 3 nos (6) cutlery drawer :- 4"- 1 nos (7) Plate Holder :- 1 Nos (8) Thali Holder :- 1 Nos (9) Pull out :- 1 Nos (10) Detergent holder and dustbin holder :- 1 Nos (11) All hinges and channels to be soft close type. (12) All handles to be standard G profile type. (Description contd on serial item No 30.01)

Note: 1. Job will be Exfecuted by manufacturer having past experience and it will be approved by GE. 2. Any other part/item not included in the specification above will be deemed to be included in the quoted rates. 3. Manufacturer will make 3D plan and get it approved by GE.

S & F of S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm completed all as specified and directed.

Complete removal of existing treatment on wall(Internal/External) /roof projections including facis, cornics etc(Internal surfaces by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc) & (External surface by Jet washer) by skilled labour complete all as specified and directed.

M & L for providing and applying minimum 1mm thick wall care putty over prepared surface and rubbing it with mechanical sander (having mechanical vaccum mechanism) to achive the surface even and smooth for further application of finishes complete all as specified and directed.

M & L for applying two coats of plastic emulsion over a coat of primer on prepared wall putty surfaces of internal wall complete all as specified and as directed.

M&L Granite 18- 20 mm thick(of any type) work (table rubbed and polished) for wall lining (Veneering to wall) and laid on cill of parapit wall over 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite colour Red or brown as per direction of GE

Providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete.

M & L 22 - 25 mm thick machine cut Kota stone slab in flooring or treads single piece of steps over and including 15mm thick screed bed in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing complete all as specified and as directed. Note:- The size of Kota stone slab shall not less than 550 mm x 550 mm cut size, except the location where the balance portion remain less than size as specified above.

Description same as per item No 37.00 above but as in skirting or vertical surfaces including 10 mm thick rendering in cement mortar 1:4, complete all as specified and as directed.

Taking down chowkhats or frames not exc 1.5 sqm each without taking off shutter from the frame complete.

Taking down chowkhats or frame exc 1.5 sqm but not exc 4 sqm with shutter (without taking off shutter frome the frame )

S & F 125 x 60 mm size Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,hold fast includ etc., complete as specified

S & F 105 x 60 mm size Pressed steel frames for door with one or more rebates including necessary lugs, hinges, lock strike plate,hold fast include etc., complete as specified

M&L for PCC (1:3:6) type C-1 with using 20mm graded stone aggregate as in bed blocks, coping, for fixing holdfast/lugs,filling hollow space of pressed steel door frame etc including necessary form work all complete as specified and as directed.

M & L 2 nd class hard wood 35 mm thick Plain , framed panelled shutters ( any number of panels), with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as speciifed and directed.

S & F 2 nd class hard wood 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass , gauze, etc, (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) fitted to chowkats complete all as specified and directed. Note :- Glass pane and wire mesh shall be measured and paid separately in respective supply only item.

S & F PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete.

S & F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR Part-II and as directed.

S & F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete .

S & F aluminium 200 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete.

S & F aluminium 150 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete.

S & F 150 mm size aluminium handles cast type, anodised ISI marked complete

S & F 250 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete.

S & F 300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate complete fixed to steel frame / wooden frame including necessary welding, cutting, opening of wall for fixing bracket and making good complete.

S & F in repair powder coated aluminium door seal 30mm wide and length as per requirement of site including dust/insect arrestor complete all as specified and directed.

S & F Powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed and one shutter wire mesh) shall be two part as upper patr shall be three movable shutter and lower part consist three shutter (one openable in centre and both side fixed type shutter with frosted glass) with following specification and making good the adjacent side of jombs of windows by plastering in CM 1: 3 even and smooth complete etc . shifting of existing cooler stand where required complete all as specified and as directed by Engr-in-charge. (i) Windows frame of cross section 101mm x 44mm x 1.5mm thick. (Min) (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm x1.1mm thick.(Min) (iii) Sliding shutter frame of cross section 40 x 18 x 1mm thick.(Min) (iv) 4 mm thick glass superior quality.(Min) (v) IDPE Rubber guasket for fixing of glass. (vi) Locking cleats per shutter -01 Nos.(Min) (vii) Sliding rollers per shutter - 02 Nos.(Min) (viii) Stainless steel wire cloth 0.30mm nominal dia of wire and average width of aperture 1.40mm for shutters 01 Nos. (Ix) fixing screw for frame with wall per windows- 08 Nos.

S & F powder coated aluminium ventilator cross section conforming to IS 63.5x38.10x1.5mm consisting of two partions upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with IDPE rubber gasket including aluminium beads, including preparation of jombs all around in CM 1:3 finishing even and smooth complete all as specified and directed.

M&L mild steel framed work such as grills , gratings, etc., with ends of bars shouldered and/ or riveted, or forged in to spikes; framed guard bars ; barred iron doors; ladders; framed balusters ; walk ways ; railings; frame work of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified.

S& F 18/19 mm thick Block boards, grade 2 quality, interior grade, commercial type, conforming to IS fixed with screws timber frame work as in cupboard , wardrobe etc.

M & L 0.9 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, conforming to IS fixed with approved adhesive over 18/19 mm thick plywood as per manufacturer's instructions complete all as directed and specified.

M & L 2nd class hard wood n.exc 6 sq.cm Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads.complete all as directed and specified.

M & L for preparation old painted surfaces of steel and iron work of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M & L Preparation of New wood or previously untreated surfaces of any description , not otherwise description, over 10 cm width or grith apply two coat of synthetic enemel paint (ordinary tint) over a coat of pink primer complete all as specifed and directed.

S & F in repairs Galvnised mild steel wire cloth, 0.56mm conforming to I S nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, wooden beads or galvanised wire staples etc complete all as specified and directed.

Demolition of Brick work built in cement mortar including all quoins arches pillars etc complete all as specified and directed

M&L Brick work with sub class 'B' modular brick straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed

M & L for reparing of RCC projection, chajjas,roofs,facia, colum etc by necessary preparation i.e scrapping ,cutting,chiseling,derusting and cleaning exposed reinforecement, surfaces of damaged, loose RCC surfaces and applying one coat of rust remover by brushing to rusted reinforecemnt to remove loose rust particles and allow to dry it for 2 to 3 Hrs , insert the new reinforcement to damaged portion by drillig hole at required distance , fill the epoxy in to the hole by 2/3 of the hole and insert the reinforcement in the hole, and binding the reinforcement at rusted portion of reinforcement, apply cement slurry on entire damaged area , and plaster the surfaces with cement , sand and Polymer liquid in 1: 3 : 15% of cement by weight ) and water as required , mixing properly and plaster the surface , finished even and smooth by making the edge water dropping groves complete all as specified and directed. Note : - Cost of formwork shall be deemed to be included in quoted rates of bidder.

M&L for rendering in cement mortar (1:6) 10mm thick first coat on fair faces of brick walls or concrete surfacesand in CM 1:4 5mm thick second coat over first coat , mixed with water proofing compound as per manufacturer instructions, finishe fair and even without using extra cement all complete as specified and as directed incl taking down existing plaster.

Supply only Integral water proofing compound

M&L for rendering 10mm thick plastering in CM (1:6) finished even & fair all as specified incl taking down plaster.

M&L for rendering 5mm thick in CM 1:3 as in soffits of ceiling and RCC chhajja/ Facia roof projections finished fair & even all as specified incl taking down plaster

M&L for applying three coats of white washing on new plastered surfaces of ceiling/wall including preparation complete all as specified and as directed.

M & L preparing old decorated plaster or un-plastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed.

Complete removal of old treatment on internal surfaces of wall by scrapping , and washing etc all as specified.

M&L for applying 3 mm Avg thick wall care putty on wall on internal old/new wall surfaces as per manufacturerer instruction complete all as specified and as directed

M & L for applying two coats of oil bound distemper over a coat of primer on prepared wall putty surfaces of internal wall all as per specified and directed.

Demolition of cement concrete (un reinforced) in ground floor and paving n. exc. 15cm thickness (below or above ground level.

M&L for PCC 1:3:6 type C2 using 40mm graded aggregate 75mm thick as in plinth protection, finished concrete surfaces even and smooth without using extra cement

S & F in repairs Sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes coupling , including bedding in cement mortar to dwarf wall or including fixing cantiliver brackets and connecting union to pipe overall size 915 mm x 460mm bowl size 410 mm x 330 x 160 mm complete all as specified and directed.

S & F in repairs vitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of tap, waste fitting etc complete. Note :- Pillar tape shall be measured as supply only under respective item

Supply only 15 mm dia bore pillar tap cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ with long screwed shanks and fly-nuts, screwed for iron pipe complete but fency type.

S & F in repair vitreous china squatting pan “ORISSA PATERN” of size 580 mm x 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete.

Supply only 10 Ltr capacity,PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with and including 32 mm dia PVC flush pipe complete all as specified and directed. Note:-Fixing only rate is included in item No above.

Supply only PVC connection pipe 15 mm dia 450 long with PTMT nut at both ends complete.

S & F (in repair) brass chromium plated angle cock 15 mm dia screwed for iron pipe or brass ferrule, complete all as specified and directed.

S & F in repair brass chromium plated towel rail 20 mm outer dia Bracket type, 60 cm long between flanges with and including chromium plated brass screws and wooden / plastic cleats, complete all as specified and directed.

S & F in repair over head shower with arm & flnge of chromium plated with or without swivel joints, any size, including fixing to 15mm dia steel pipe for required length or union complete all as specified and directed

S&F in repair 15 mm dia concealed type stop valves, cast copper alloy, chromium plated, screwed down, high pressure with handle, screwed both ends for iron pipe or union complete all as specified and directed

S&F 15mm dia Bib tap chromioum plated with crutch or butterfly handle sorewed down screwed for iron pipe or for brass ferrule and fixedcomplete.

S&F in repairs powder coated steel peg set having 06 Nos spikes fixed to wall complete all as specified and directed (Make as spproved by GE)

S & F in repair PVC bath cabinet box mirror type with shutter complete.

S&F harrison rail/curtain rod, mild steel chromium plated with fixing bracket, stops and complete fitment all as specifed and as directed.

S & F in repair corner shelf of 300 mm size with ABS brackets complete.

S & F in repair CP tumbler Holder, complete all as specified and directed by Engineer-incharge.

S & F in repair Gun-metal, globe of gate balve /flush cock of 20mm bore with iron wheel head, screwed both ends for iron pipe etc all as specified.

S & F in repair PVC (SWR) nahani trap with grating having diameter of outlet 75 mm including joining to waste pipe with solvent cement complete.

S & F in repair 110 mm dia bore. PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor/ trenches complete all as specified and directed.

S & F in repair 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor/ trenches complete all as specified and directed.

S & F in repair 110 mm dia bore. PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls complete all as specified and directed.

S & F in repair 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S & F in repair 110 mm dia bore PVC (SWR) bends with acess door any radius with solvent rubber ring joints, fixed complete all as specified and directed.

S & F in repair 75mm dia bore PVC (SWR) bends with acess door any radius with solvent rubber ring joints, fixed complete all as specified and directed.

S & F in repair 110 mm dia bore PVC (SWR) junction single, single (T) equal or unequal with acess door with solvent rubber ring joints, fixed complete all as specified and directed.

S & F in repair 75mm dia bore PVC (SWR) junction single, single (T) equal or unequal with acess door with solvent rubber ring joints, fixed complete all as specified and directed.

S & F in repair 110 mm dia bore PVC (SWR) vent cowl rubber ring joints, fixed complete all as specified and directed.

Demolition of reinforced cement concrete of any description for manhole cover, slab of septic tank & soak well etc complete.

M & L providing pre-cast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab of manholes, septic tank, soak well etc set in cement mortar 1:4 with plain fair faces including chamfered weathering, throating etc including necessary use and waste of form work complete.

S & F mild steel TMT bars 10 mm dia and over as in reinforcement, cut to length, benty shape required including cranking, bending, spirally for hooping for columns, hooking ends and hinding with mild stee wire (annealed) not less than 0.9 mm dia or securing with clips complete.

Surface excavation n. exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type soil complete all as specified and directed

Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M & L PCC 1:4:8 type D-2 using 100 mm graded stone aggregate as in mass concrete complete all as specified and directed.

M & L 60 mm thick Machine pressed precast concrete interlocking paver blockfixing with grey cement and pigments OF " I " shape or as approved by GE ,and any colour and size confirming to IS 15658-2006 of M-35 Grade set , laid over 50 mm (average) thick dust sand cushioning,filling of joints with sand & compaction using surface vibrator after filling of joints lain in any pattern as decided by Engineer-In-Charge including packing of sides by cement concrete finishing surfce even and smooth complete all as specified and as directed. Note : Sand cushioning shall be measured and paid separately .

S & F Joist channel, angle or tee, square or rectangular tubler sections fixed independently or as purlin, rafter or post incl cutting to dead length where required notching drilling firing riveting and/or welding or connecting with bolts and nuts providing and fitting angle cleats fish plates, gusset plates etc complete all as specified and directed (Fe-410-W (gde-E-250) quality A)

Treating the soil under the plinth protection at the rate of 5 litre of emulsion per square metre of surface area.complete all as directed and specified.

S & F Pre-painted galvalum aluminium zinc coating steel based corrugated steel sheet 0.50mm thick (total coated thickness) of any colour having tensile strength of 550 Mpa minimum, yeild strength, it shall be coated with hot dip alloy of 55% aluminimum, 43.5% zinc,1.5% Silicon and finished with resin coat on both surface @ 150 gm/ sqm of coating as specified and shall be fixed with hot dip galvanised, self drilling and self tapping screws neoprened and EDPM washers as in roof covering all as directed at site all as specified and dircted.

M&L for preparation old/new decorated surface of wall/ceilling to be done by mechanical means/smart painting technique coats of acrylic latex base exterior grade (100% ACRYLIC) over a coat of primer at any height including 1 mm thick exterior putty and crack to be filled with crack filler and necessary scaffolding complete alongwith five year warrantly complete all as specified and directed Note:- Painting work shall be executed through authorized and certified applicator of paint manufactures of paint companies. 2. Approval shall be obtained from GE for make/manufacturers and applicator before engagement in the work. 3. Contractor shall provide five year written guarantee certicate for the paint work.

M&L for applying one coat primer acrylic polymer modified water proofing coating (Brushband of FOSROC or equivalent) and over that two coats of acrylic polymer modified two component elastometric water proofing membrane coating (Brush band of Fosroc or equivalent) complete all as specified as per manufacturers instruction as directed Note :- 1. This item shall only be executed through level 4 or level 5 certified and authorized applicator of the company. 2. Approval shall be obtained from GE for make/manufacturers and applicator before engagement in the work. 3. The rate quoted by the contractor shall include all the provisions mentioned in this item including notes.

M & L cutting chases in brick wall for concealed water tubing, pinning in, making good of facings where required and pointing in cement mortar 1:3 to ends or edges etc, cutting not exceeding 10 cm width or girth, complete.

S&F in repairs shelf glass assembly consisting of 5.5 mm thick sheet glass , shelf 120 mm wide with CP bracket guard and railing 600 mm long all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over of redoxide zinc chrome coat complete all as specified and as directed.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface all as specified and directed.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Taking down existing geyser of any capacity after disconnecting all necessary electrical and water supply connections and deposit to MES store yard of AGE E/M No II complete all as specified and as directed.

Taking down existing single phase electric energy meter of any capacity after disconnecting all necessary electrical connections and deposit to MES store yard of AGE E/M No II complete all as specified and as directed.

M&L point wiring with 1.5 sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel modular terminal boxes any size/module, conceiled on walls and fixed by neans of brass screws incl modular cover plates and cover frme any size/module, for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for the following complete for One light / fan /bell controlled by one, one way switch 5/6 Amps all as specified and as directed .

Description all as per item No 126.00 here in above , but for one 3 pin, 5/6 amps socket outlet point on independent board controlled by one, one way 5/6 amps switch

Description all as per item No 126.00 here in above , but for one 3 pin, 5/6 amps socket outlet point on same board controlled by one, one way 5/6 amps switch

M&L point wiring with 2.5 sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 2.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel modular terminal boxes any size/module, conceiled on walls and fixed by neans of brass screws incl modular cover plates and cover frme any size/module, for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one 15A socket point independent complete incl taking down of old unsv point wiring all as specified and directed.

S&F in replacement of Ceiling rose three terminals surface bakelite type, AC, 50 HZ, 230V complete all as specified and directed.

S&F modular switch 1 way 6 A , 1 module complete all as specified and directed.

S&F modular socket 6 Amps 2/3 pin combined 2 module complete all as specified and directed.

S&F switch modular type 16 A, 1 module complete all as specified and directed.

S&F socket modular type multipurposes 6/16 A, 2 module complete all as specified and directed.

S&F modular bell push type 6 A ,1 module complete all as specified and directed.

S&F bell multi music type AC 230 volts single pole complete all as specified and directed.

S&F surface /wall mounted LED batten (other than slim channel type) poly carbonate housing for retrofit LED tube T-8 type upto 1x22 watt, 4 feet long pre wired incl integrated electronic driver complete with all connected accessories all as specified and directed.

S&F ultra bright LED poly carbonate tube light 4 feet long 18 to 20 watts with THD less than 15% very high effficiency suited for T-8 tube light luminare with system efficiency 120 lumens per watts. High quality polycarbonate end cap in white finish and snap fitted to the housing complete all as specified and directed.

Supply and fixing wall mounted LED tube light fitting 10 watts comprising batten of extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver 10 W LED 2 feet long ,THD less than 15% complete all as specified and directed

M&L for Modular angular holder with LED Bulb 9 watts complete all as specified and as directed

M&L for LED Bulk head fitings 6.5 watts designed for modern homes available with premium quality diffuser for glarefree light and easy to install snapfit installer complete including taking down of old CFL/bulb bulk head fitting, making good of surfaces all as specified and directed.

S & F LED bldg security light fitting 30 watt made up of pressure die cast aluminium housing with acylic cover as diffuser with IP-66 protection complete incl mounting pipe made of GI tubing 40 mm size 1M length bend into size with mounting brackets nut bolt and washers all as specified and directed.

S&F MCB DB SPN 8 way ,IP-43, IK 09, double door type with metal door with 200 Amps rated bus bar ,230 volts, 50 Hz complete all as specifed and directed.

Supply & Fix MCB SPN 40 to 63 Amps current rating 'C' series 10 KA breaking capacitycomplete all as specified and directed.

Supply & Fix MCB SPN 32 Amps current rating 'C' series 10 KA breaking capacitycomplete all as specified and directed.

Supply & Fix MCB SP 6 to 32 Amps current rating 'C' series 10 KA breaking capacitycomplete all as specified and directed. Note - Make of MCBs should be same as that of item no. 143

Supply and fixing TV socket outlet complete all as specified and as directed.

M & L sub main wiring with 2 runs of 10 sqmm main wire along with 1 run of 10 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC concealed / surface conduit (medium grade) wherever necessary with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good disturbed surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

Taking down existing exhaust fan/ceiling fan of any sweep after disconnecting necessary connection from ceiling rose to fan and deposit to MES store yard complete all as specified and as directed

M&L for refixing exhaust fan non metalic single phase 230 volt of size 250 mm sweep with louver incl necessary alteration in Aluminium or Iron window all as specified and as directed

M&L for refixing ceiling fans 1200 mm sweep obtained from taking down complete incl painting with spray paint , replacing conopy ,painting of down rod , provision of two core wire 1.5 sqmm from ceiling rose to connector of fan incl making functional complete all as specified and directed.

M&L for refixing exhaust fan 300 mm sweep obtained from taking down item complete incl painting with spray paint , replacing metallic louvers , provision of two core wire 1.5 sqmm from ceiling rose to connector of fan incl making functional complete all as specified and directed.

Supply , fixing rigid non metallic PVC conduit fixed conceiled/on wall wherever necessary with all connected accessories 20 mm dia for cable TV connections complete all as specified and as directed

Supply, installation, commissioning and testing indoor type LT wall mounting Panel Board of minimum size 1.00 m (height) x 1.00 m (breath) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four compartment for fixing of six Nos single phase meter and MCB and providing glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/sleeves with maintained the colour code and copper strip/wire busbar of suitable size to MCCB input and MCCB/MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of Powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 2.5 sqmm copper wire and connections of all outgoing / incoming existing cable of any size complete incl MS angle Iron 40x40 mm and galvalume sheet for protection of LT panel from rain/water all as directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for laying of cable, pipes etc and getting out all excavated material in any type of soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. thick complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm complete all as specified and directed.

M&L for River sand filling in trenches below and above/ arround UG cable for cable protection, in duct under& abovethe cables incl punning arround cable complete all as specified and directed.

Supplying, laying, fixing, jointing and testing LT under ground XLPE insulated, galvanised steel strip or wire armoured heavy duty electric cable with aluminium conductor , multi stranded 1100 volts grade, cross-sectional area 35 sq. mm 3.5 core, ISI-7098 marked, with electric connection lugs, laid in trenches/under floor under PCC/interlocking tiles incl making good of surface with PCC/ cementing or fixed naked with walls/on poles/in ducts/in GI pipes etc and including taking down complete trenches / all as as directed at site. Note: Excavation, earth work, sand cushioning, protection tiles/brick/block shall be measured and paid seperately.

M&L for Tubes, 'light grade,galvanised, with all fitting of size 40 mm ;laid in trenches, under floors,roads,along poles for protection of cable with all necessary fittings and sealing ends complete all as specified and directed.

Replacement of Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in ground vertically to a depth not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level connect to galvanised earth lead wire of 4.0 sqmm size by means of bolts, nuts, check nuts and washers of galvanized iron or steel up to 7.5 meter length including connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber, 40 mm thick RCC cover 1:2:4 mix with 6mm dia nominal reinforcement @ 150 mm c/c both ways etc complete all as shown in electrical plate No 3, connected to earthing test point complete including testing on completion all as specified.

M&L for refixing electric water heater 25 Ltr capacity obtained from taking down item complete incl spray painting , replacing 2 Nos PTMT connectors , replacing 3 core 2.5 sqmm connecting wires from power point to connector of geyser incl writing MES number all as specified and directed.

M&L for refixing electric water heater 25 Ltr capacity obtained from taking down item complete incl spray painting , replacing 2 Nos PTMT connectors , 4 nos hold fastners . replacing 3 core 2.5 sqmm connecting wires from power point to connector of geyser incl writing MES number all as specified and directed.

M/S DADISA CONSTRUCTION (BID ID -3161823)

M/s. Shubh constructions (BID ID -3161151)