REPAIR/REPLACEMENT OF VERTICAL PUMPS/ SUBMERSIBLE PUMPS/ CENTRIFUGAL PUMPS/STARTER PANEL/ LT PANEL BOARD AND OTHER CONNECTED ITEMS UNDER GE PULGAON

Amount

Disconnection and removing the top cone unit (split casing cover) of the unserviceable pump 120HP along with suction, delivery pipe line, control valves etc and refixing the disconnected parts after replacing unserviceable parts with the new parts of same size, capacity and make and making the pump in serviceable condition including testing and commissioning complete all as specified and directed. (Note:- The replacement of unserviceable parts with new parts will be measured and paid separately under respective items of sch 'A' as supply only and labour element for fixing including greasing, overhauling and packing of pump set will be included in the unit rate quoted for this item.)

All as per item No 1.00………. but for 110 HP

Disconnection and removing the unserviceable Electric motor 120 HP and transporting the same to work shop for rewinding and fixing the same in its original position after repairs, including testing and commissioning complete all as specified and directed.

All as per item No 3.00………. but for 110 HP

Material & labour for rewinding of 120 HP electric motor with fine enamelled bared copper conductor of same gauge weight and turn along with insulating materials such as impregnated paper, cotton tap, varnish etc and keeping the rewinding in to the hot air oven till moisture evaporates and achieving proper insulation results and reassemble the motor including taking out old rewinding complete all as specified and directed.

All as per item No 5………… but for 110 HP

Supply only for spares parts suitable for 120 HP pump set:-

Coupling along with nut, bolts and key unit complete

MS Impeller of suitable capacity

Impeller lock nut

Impeller sleeves

Guides

Bearings suitable to the pump set (3309)

Bearings suitable to the pump set (6309)

Gasket

Material and labour for painting of the pump set of capacity 120 HP with suction/delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of color as approved by GE.

Shaft stainless steel suitable for pump set including machining, threading, metalling & lathework complete all as specified and directed.

Bearings suitable for 120 HP motor (for drive end & dead end) (317C-3/6317C-3)

Rubber Pully

MS Pully

Supply only for spares parts suitable for 110 HP pump set:-

Coupling along with nut, bolts and key unit complete

MS Impeller of suitable capacity

Impeller lock nut

Impeller sleeves

Guides

Bearings suitable to the pump set(3309)

Bearings suitable to the pump set(6309)

Gasket

Rubber Pulley

MS Pulley

Material and labour for painting of the pump set of capacity 110 HP with suction/delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of colour as approved by GE.

Shaft stainless steel suitable for pump set including threading, machinery & lathe work complete.

Bearings suitable for 110 HP motor (for drive end & dead end) (6316&6314)

Disconnection and removing of the 7.5 HP monoblock pump along with suction, delivery pipe line, control valves etc and finding out the unserviceable parts and refixing the disconnected parts after replacing of unserviceable items with new of same size and capacity including testing and commissioning complete all as specified and directed. (Note:- (i) Unserviceable parts will be measured and paid separately under respective items of sch 'A' (ii)Greasing, overhauling and packing of pump set will be include in the unit rate.)

Material & labour for rewinding of 7.5 HP electric motor with fine enamelled bared copper conductor of same gauge weight and turn along with insulating materials such as impregnated paper, cotton tap, varnish etc and keeping the rewinding in to the hot air oven till moisture evaporates and achieving proper insulation results and reassemble the motor including taking out old rewinding complete all as specified and directed.

Supply only for spares parts suitable for 7.5 HP monoblock pump set:-

Coupling along with nut, bolts and key unit complete

MS Impeller of suitable capacity

Impeller lock nut

Impeller sleeves

Bearings suitable to the pump set

Gasket

Material and labour for painting of the pump set of capacity 7.5 HP with suction/delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of color as approved by GE.

Shaft stainless steel suitable for pump set including threading, machinery & lathe work complete.

Bearings suitable for 7.5 HP motor (for drive end & dead end)

Disconnection and removing the 60 HP VT pumpset along with suction, delivery pipe line,column pipe, control valves,shafts & shafts coupling etc and finding out the unserviceable parts and refixing the disconnected parts after replacing of unserviceable items with new of same size and capacity including testing and commissioning complete all as specified and directed. (Note:- Unserviceable parts will be measured and paid separately under respective items of sch 'A' lubricating oil, Greasing, overhauling and packing kit of pump set including in the unit rate.)

All as per item No 12………… but for 30 HP.

Material & labour for rewinding of 60 HP VT electric motor with super enamelled winding wire of same gauge weight and turn along with insulating materials such as impregnated paper, cotton tape, varnish etc and keeping the rewinding in to the hot air oven till moisture evaporate and achieving proper insulation results and reassemble the motor including replacement of terminal plate and taking out old winding complete all as specified and directed.

All as per item No 14………… but for 30 HP.

Supply only for spares parts suitable for 60 HP VT pump set:-

O Ring Part No 524 and 522.1

Wear Ring part No-190

Trans Bearing

Shaft Sleeve Part No 312

Shaft Sleeve Part No 311.2

Bowl Bearing

Material and labour for painting of the pump set of capacity 60HP delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of color as approved by GE.

Bearings suitable to the pump set(No 7316)

Bearings suitable to the pump set(No 6211)

Supply only for spares parts suitable for 30 HP VT pump set:-

O Ring

Wear Ring

Trans Bearing

Shaft Sleeve Part No 312

Shaft Sleeve Part No 311.2

Bowl Bearing

Material and labour for painting of the pump set of capacity 30HP delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of colour as approved by GE.

Bearings suitable to the pump set(Upper)

Bearings suitable to the pump set(Below)

Taking out defective submersible (vertical) pump set of capacity 7.5 HP/10HP from bore well for repair by lifting GI tubing of size 50mm to 150 mm GI/CI/MS pipe from upto 220 to 250 feet depth after disconnecting electrical and pipe line connection, complete by means of chain pully block or other T&P, transporting to workshop including repair/replacement of worn out parts, servicing and overhauling complete with oiling/greasing, lubricating the parts and reassembling and painting of submersible pumpset with motor with one coat of synthetic enamel paint after cleaning and scrapping and shifting back to borewell, lowering commissioning and testing on full load complete all as specified and directed. [Note :- (i) The rate quoted for this item shall includes labour charge for maint repair and replacement of defective/UNSV spare parts/accessories with new spare parts. New spare parts are to be measured and paid separately under subsequent items. (ii) Cost of other minor items/ spares such as nut, bolts, washer, gaskets,paints etc which are not covered under Sch 'A' but required for efffective functioning of the plant shall be deemed to included in this items.

All as per item No 18…………3 HP/5 HP.

All as per item No 18………… 0.75 HP.

Supply only the following items/parts for 7.5 HP/10HP submersible borewell pump etc.

Thurst bearing complete

Gun metal bearing bush

Stainless steel studs and nuts

Shaft for pump

Shaft for motor

Stainless steel motor coupling with key

Bowl assembly

Bowl assembly ring

SWR rope 6mm

Supply only the following items/parts for 3HP/5HP submersible borewell pump etc.

Thurst bearing complete

Gun metal bearing bush

Stainless steel studs and nuts

Shaft for pump

Shaft for motor

Stainless steel motor coupling with key

Bowl assembly

Bowl assembly ring

SWR rope 6mm

Supply only the following items/parts for 0.75HP submersible borewell pump etc.

Thurst bearing complete

Gun metal bearing bush

Stainless steel studs and nuts

Shaft for pump

Shaft for motor

Stainless steel motor coupling with key

Bowl assembly

Bowl assembly ring

SWR rope 6mm

Dismantling the motor of submersible (vertical type) pumpset of capacity 7.5HP/10HP, removing the existing burnt out winding and re-winding with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and filling of cooling oil with oil seal and terminal lead for AC, three phase, 415Volts grade and other petty items required for making motor functional and motor reassembling and testing complete all as specified and directed.

All as per item No 24………… but for 3 HP/5 HP.

All as per item No 24………… but for 0.75 HP.

M&L for CI non return valve heavy duty both end flanged incl making flanged joint, rubber gasket, nuts & bolts washers sizes 200 mm complete all as specified and directed. (Make:Kirloskar/Upadhayaya/Leader)

All as per item No 27.00… but for 150 mm dia.

Spray painting of the MS fabricated structure of Sedimentation tank (two parts) including filter bed, outlet sliuce valve complete by one coat of synthetic enameal paint as approved by Engr-in-charge complete all as specified and directed. (Note :- necessary safety precautions should be taken in the cost of using safty belts is deem to be included in the cost)

Supply and fix CI Foot valve unit, suitable for 200mm bore incl required nuts and bolts etc and cone set the same to the suction pipe of the pump set availble in to the sum appx hight of 14 feet below the ground lavel of the sump complete all as specified and directed. (Make: Kirloskar/Upadhya/Leader )

All as per item No 30.00... but for 150 mm bore.

S & F of MCCB 3 pole, 250 Amp,36kA, 415V AC, 50 Hz in to the existing panel board with new one of same size and capacity complete all as specified and directed. (Make L&T/Havells/CG)

S & F of MCCB 3 Pole 160Amp, 36kA, 415V AC, 50 Hz in to the existing panel board with new one of same size and capacity complete all as specified and directed. (Make L&T/Havells/CG)

S & F of MCCB 3 Pole 100Amp, 16kA, 415V AC, 50 Hz in to the existing panel board with new one of same size and capacity complete all as specified and directed. (Make L&T/Havells/CG)

S& F of MCCB 3 pole, 200Amp, 415V ,36 kA,load line type with thermal setting in to the existing panel board with new one of same size and capacity complete all as specified and directed. (Make L&T/Havells/CG)

Supply & fix in power contactor MNX 140, 3 Pole, 415 V, Current rating 140 A, 2NO + 2NC having coil voltage 240 Volts including taking down the U/S power contractor complete all as specified and directed.( Make : L&T/Havells/CG)

Supply & fix power contactor MNX-70, 3 Pole, 415 V, Current rating 70 A, 2NO + 2NC having coil voltage 240 Volts including taking down the U/S power contractor complete all as specified and directed. (Make : L&T/Havells/CG.)

Supply & fix power contactor ML-6, 3 Pole, 415 V, Current rating 110 Amps, 2NO + 2NC having coil voltage 240 Volts including taking down the U/S power contractor complete all as specified and directed.(Make : L&T/Havells/CG.)

Supply & fix spare parts kit for 3 pole 70Amps, 415 volts, with coil rating 230/415 volts, type ML-4 complete all as specified and directed. (Make L&T/Havells/CG.)

Supply & fix spare parts kit 3 pole MNX 140 including taking down the U/S power contractor complete all as specified and directed. (Make : L&T/Havells/CG)

Supply & fix spare parts kit for 3 pole 110Amps, 415 volts, with coil rating 230/415 volts, type ML-6 complete all as specified and directed.(Make L&T/Havells/CG.)

S&F Bimetalic Overload relays suitable for Power Contactor 40Amps, 415 volts, with coil rating 230/415 volts type ML-3 complete all as specified and directed.(Make L&T/Havells/CG).

S&F Bimetalic Overload relays suitable for Power Contactor 70Amps, 415 volts, with coil rating 230/415 volts complete all as specified and directed.(Make L&T/Havells/CG) .

S&F Bimetalic Overload relays suitable for Power Contactor 110Amps, 415 volts, with coil rating 230/440 volts complete all as specified and directed.(Make L&T/Havells/CG) .

Disconnection and removing the broken stainless steel spindle with checknut and S&F brass spindle of same size and length along with checknut suitable for sluice valve 300 mm bore PN 1.6/PN1 of exisisting makes including threading machining and Lathe work complete along with fixing material such as gland packing nut and bolts complete all as specified and directed

All as per item No 45.00...but for 200 mm bore.

All as per item No 45.00...but for 150 mm bore.

Taking up cast iron water mains 300mm dia of any class (including all fittings), with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and directed

All as per item No 48.00… but for 200mm

All as per item No 48.00… but for 150mm

Excavation in trenches, not exc. 1.5 mtr wide and not exc. 1.5 mtr in depth for foundation, etc in soft loose soil complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and wall remming in layers not exc 25 cm complete all as specified and directed

Removing excavated material n.exc 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and directed

M&L for CI special/fittings suitable for CI flanged/socket ends pipe upto 150 to 300 mm bore dia such as bends, (any radius and angle), tapers any type (straight, bend, increasing, decreasing or double socket etc) tee piece, single branch 'Y' junction, double branch, cross (all flanged), collars, caps & plug, tail pieces, reducers, mechanical joint, etc. complete all as specified and as directed,

Supply and fix cast iron pipes with spigot and socket ends centrifugally costed class B in any length suitable for rubber tytan joint and Laid in trenches of size 300mm bore.(Make: Electrosteel/ Kapilansh Dhatu Udyog).

All as per item No 55.00… but for 200mm bore.

All as per item No 55.00… but for150mm bore.

M&L for burning out lead joint in position , including removing lead to store / stacked at site to issue under credit of 300mm bore CI Pipe line

M&L for Run lead joint of 300 mm bore of spigot socket pipes and fitting, including caulking properly and making joint leak proof complete all as specified and directed

Servicing of Iron removing plant with pressure filter, catalytic media, air compressure, suitable for back washing of capacity 1000 GL/H complete in all respect. Make ELGI. (Note: U/S spare parts shall be measured and paid separately as supply only here in after).

Air filter

Air oil separator

Oil filter

Air Lub oil

Supply, installation, commissioning and testing of star delta stater fully automatic suitable for 30 HP/40 HP submersible pump, 415 volts 3 phase, 50 Hz including taking out of existing u/s starter as complete all as specified and directed. (Make-L&T/Siemens/Schneider (CG).)

S&F in repair Pressure gauge range 0-21 KG per cm square for centrifugal pump/VT Pump set proper fix suitable point with suitable fixing arrangement (i.e nut bolt, boresuitable,fixing pipe for pressure gauge on mounting complete all as specified and as directed.

Supply & fix champion/turner style graphite gland packing of sizes as 8/10/12/16mm thick for motor/sluice valve complete all as specified and directed

Dismantaling of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed

M&L for Cement concrete 1:2:4 B-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed

Repair to CI valve for back wash in filter plant ( Plate type) 200MM, including threading, machinery and lathe work complete along with fixing material such as Rubber sheet packing, nut and bolts,etc complete all as specified and directed

All as per item No 66.00… but for150mm bore.

M&L in repair chequered plate including cut to required size and making provision of handle made out of 6 mm plane rod,including painting with two coats of synthetic enamel paint over one coat of red oxide complete all as specified and directed

Taking down existing UNSV sluice valve and supply & fix new Sluice valve of 80mm bore rising spindle type (Gear type) PN-1.6 heavy duty ISI marked as per (IS-14846) with flanged ends with 02 Nos of rubber gaskets, nut bolts and washers along with stainless steel spindle and operating wheel. Make : Kirloskar/Leader/Venus.

All as per item No 69.00… but for 150mm bore.

All as per item No 69.00… but for 200mm bore.

All as per item No 69.00… but for 300mm bore.

Supply and fix in repair and replacement of leather flapper for the 200mm CI Foot valve unit, including required nuts and bolts etc and cone set and fixing the same to the suction pipe of the pump set availble in to the sump appx at a height of 15 feet below the ground level of the sump complete all as specified and directed

M&L for Spray painting of MS sheet cover of Valve chamber cover/US sump cover/ filter water reservoir square type of water supply all installation with two coat of synthetic enamel paint colour coat over a coat of red oxide primer complete all as specified and directed

M& L for Painting of Air release valve and MS angle iron structure with two coat of synthetic enamel paint a colour coat over a coat of red oxide primer complete all as specified and directed

S&F in repair Mild steel work in Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed

S&F in replacement of microprocessor based electronic water level indicataor based on 3 wire interfacing system in between OH Tank/UG Tank sensor to main water level indicator units showing indication in percent by seven segment LED display in 10 step (10%, 20%, 30% ............100%) having 10 combined sensor for total depth of tank of make : Serval/Optic/ IEC/Benzer with all fixing/grouting arrangement suitable for RCC OH Tank/UG Tank of 0.5 to 1.5 lakh gallons capacity including dismantling and taking down old unserviceable water level indicator, any type and depositing to MES store yard complete all as specified and directed. Processor based electronic water level indicator shall also comprising of the following items:- Multi level (10 to 100%) indication in three digit with seven segment with bright LED display. Sensor with suitable fixing arrangement in over head tank having electronic circuit to transmit the sensing signal of each level to display unit shall be fitted in pump house. Controller/power unit with sensing volts (6-12 volts) enclosed with sheet metal enslosure/wooden board and hylam sheet including proper mounting arrangements. PDC insulated multi- stranded copper conductor communication cable 2.5Sqmm, 3 core from LT Panel to controller/power unit drawn through 20mm dia non metalic PVC conduit medium grade with all accessories including all fixing arrangements. Hooter with ON/OFF switch to alarm the pump operator when tank is full complete all as specified and directed

Material and labour for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earths strip 32 X 6 mm size by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 5 of MES Schedule Part-I connected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete all as specified and directed

All as per item No 78.00… but for size of 25mm x 4mm conductor.

M& L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required size 32mm x 6mm galvanised iron strip complete all as specified and directed

All as per item No 80.00... but for size 25mm x 4mm conductor.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated multi strand copper conductor cable size 95 Sqmm, single core unsheathed flexible complete all as specified and directed

S&F PVC copper cable,single core,flexible with lugs ,FR type,copper conductor etc of size 95 sqmm including taking down old unsv cable complete all as specified and directed by Engr-In-Charge.

S&F PVC copper cable,single core,flexible with lugs ,FR type,copper conductor etc of size 70 sqmmincluding taking down old unsv cable complete all as specified and directed by Engr-In-Charge.

Supply, installation, commissioning and testing of smart star delta stater fully automatic ,LCD based,Digital time setting ,Smart/Auto switch ,protects motor against reverse running & unbalanced voltage conditions for upto 120 HP centrifugal pump, 440 volts 3 phase, 50 Hz including taking out of existing u/s starter as directed. Make- L&T/Siemens/Schneider (CG).

Supply, installation, commissioning and testing of DOL stater fully automatic suitable for upto 7.5HP monoblock pump, 415 volts 3 phase, 50 Hz,6-10A including taking out of existing u/s starter as complete all as specified and directed. (Make- L&T/Siemens/Schneider/CG)

Supply, installation, commissioning and testing of star delta stater fully automatic suitable for 7.5/10 HP submersible pump, 415 volts 3 phase, 50 Hz,phase preventor including taking out of existing u/s starter as directed. (Make- L&T/Siemens/Schneider/CG)

M&L cleaning the Decrin dozer assembly complete by opening of nut, bolts gate valve and connected GI fitting and refixing/assembling complete all as specified and as directed.

Comprehensive maintenance and repair of calcium hypochlorite based electronic automatic dosing equipment 100 Ltr capacity of any type and make complete with dozing tube and solution drum and other accessories required. Note :- (i) Spare items/parts required for chloronomes plant shall be measured and paid separately under relevent items. (ii) Cost of items /parts which are not covered in Sch 'A' but are necessary for the satisfactory functioning for the plant shall be included in the rate quoted for this item. (iii) Dosing pump to be cleaning twice in a month (15 days) and serviceability report to be submitted to Engr-in-charge for office record.(iv) Labour charges for removal of unserviceable parts and fixing of spare items/parts (supplied under the item No-41) shall be deemed to be included in the rate quoted for this item.

M&L for replacement of the following spare parts of decrine dozer :-

Pump head (Ferrules 1/4" & Duckbill included)

Roller assembly

Pump tube

Injection check valve 3/8"

Weighted suction line strainer 3/8"

Rotor assembly with bearing brackets & tolerance ring

Coil 250V 50Hz

3/8" White suction/Discharge tubing

Supply and laying of flexible PVC pipe 80mm bore for connected with D-watering pump

Servicing of D-Watering Pump capacity 7.5 HP and taking out the defective/unserviceable parts and re-assembling the same after repair/replaced and testing complete all as specified and directed. (Note : U/S spare parts shall be measured and paid separately as supply only here in after).

Diesel filter

Oil filter

Oil pressure gauge

Hose pipe set with clamps & clips complete.

S &F of single phase preventor(Phase failure relay) 415Volt,50 Hz,Type-VSP 3 complete all as specified and directed.

Supply, installation, commissioning and testing of Soft Starter fully automatic suitable for 90 KW/120 HP centrifugal pump, 415 volts 3 phase, 50 Hz, including taking out of existing u/s starter as directed and the accessories/parameter are as under complete all as specified and as directed Make- L&T/Siemens/Schneider/CG. Incommer Section:-

Panel enclosure with angle iron stand (H 800mm x W 600mm x D 400mm) - 01 No

MCCB 250 Amps, 3 Pole with spreader and rotary handle - 01 No

Control MCB 6A - 06 Nos

Semiconductor Fuse 200 Amps with base - 03 Nos

Fan 6" & Filters - 01 No

Voltmeter - 01 No

Ammeter - 01 No

Outgoing Section:-

ON/OFF Indicator - 02 No

ON/OFF push button - 02 No

Chhabra Enterprises

M/S JAI BHAWANI CONSTRUCTIONS

M/s MM TRADERS

M/S Maa Durga Constructions,Pulgaon

Bidder Name

M/S Maa Durga Constructions,Pulgaon

M/s MM TRADERS

M/S JAI BHAWANI CONSTRUCTIONS

Chhabra Enterprises

SHUBHAM SALES