Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹40.4 LAccepted-AOC | L1 | Accepted-AOC Being L1 bidder | |
| 2 | L2₹43.9 L+₹2.1 L (5.06%)Rejected-Finance | L2 | Rejected-Finance Other than L1 Bidder | |
| 3 | L3₹45.0 L+₹3.2 L (7.75%)Rejected-Finance | L3 | Rejected-Finance Other than L1 Bidder | |
| 4 | L4₹46.1 L+₹4.3 L (10.3%)Rejected-Finance | L4 | Rejected-Finance Other than L1 Bidder | |
| 5 | L5₹47.1 L+₹5.3 L (12.7%)Rejected-Finance BOGDANG NUBRA PIN 194101 | BOGDANG | NUBRA | LADAKH | 194101 | L5 | Rejected-Finance Other than L1 Bidder |
Tender Value
₹45.4 L
EMD Value
₹91,000
Closing Date
3 Sept 2024, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE 873 EWS
Garrison Engineer 873 Engineer Works Section PIN 913 873 C/O 56 APO
PROVISION OF TOILETS AND BATHROOMS AT TYAKSHI UNDER GE 873 EWS
2024_MES_663662_1
GE/873/EWS-49/2024-25
Open Tender
Civil Works
Item Rate
270 days
GE 873 EWS
Please refer NIT and Tender Documents
8 documents required · 8 mandatory
₹500
GE 873 EWS
₹91,000
Yes
28 Sept 2024
3 Jul 2024
5 Sept 2024
3 Jul 2024
3 Sept 2024
17 Jul 2024
5 Jul 2024 - 9 Jul 2024
Amount
Surface dresssing nexc 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.
Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.
Excavating over areas, exc 1.5 m and not exc 3.0m deep and getting out in hard/dense soil complete all as specified and directed.
Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/densc soil complete all as specified and directed.
Returing, filling in incl spreading, levelling watering and well remming in layers n.exc 25cm width, Complete all as specified and directed.
Removing excavated soil to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 m above starting point Completed all as specified and diercted.
M&L for PCC 1:2:4, type B-2 (using 40 mm graded crushed stone aggregate) in foundations, filling and mass concrete, complete all as specified and directed.
M&L for RCC M-30 (Design Mix) (20mm graded stone aggregates) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs, under-reamed piles and mass concrete complete all as specified and directed.
M&L for RCC M-30 (Design Mix) (20mm graded stone aggregates) in Columns, pillars, piers, posts and struts complete all as specified and directed.
M&L for RCC M-30 (Design Mix) (20mm graded stone aggregates) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.
M&L for RCC M-30 (Design Mix) (20mm graded stone aggregates) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed.
M&L for steel TMT bars, 10 mm dia and over , cut to length, bent to required shape including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (anealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.
Ditto all as per item no. 12.00 here-in-before but 6mm dia and over upto 10mm dia in stirrups, spacers and binders complete all as specified and directed.
M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work complete all as specified and directed.
M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finish complete all as specified and directed.
M&L for formwork to soffits of flat surface suspended slabs such as roof slabs,floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finish surface complete all as specified and directed.
M&L for formwork to sides and soffits of floor or roof beams, beam haunch-ings, lintels, cantilevers, shelves including sup- ports, overhangs, etc. complete all as specified and directed.
M&L for Providing precast cement concrete solid building blocks (1:3:6), Type C-1 (using 20mm graded stone aggregate) exc 20cm thick setting in mortar (1:6), in walls complete all as specified and directed.
M&L for Providing precast cement concrete solid building blocks (1:2:4), Type B-1 (using 20mm graded stone aggregate) 10cm thick setting in mortar (1:4), in walls complete all as specified and directed.
S&F plain, solid, straight chowkats of second class hard wood and frames, wrough, framed rebated on the solid, rounded or chemfered, put together with glue pinned at joints complete all as specified and directed.
S&F 35 mm thick factory made 2nd class hard wood plain, framed, panelled shutters (two panels) with lock rail and panelsof 9mm thick BWP commercial; ply or 12mm thick veneered p article boards on both sides. The size of rail and style as per IS-1003 (part-I) kiln seasoned and chemicaly pressure treated complete all as specified and directed.
S&F 25mm thick 2nd class Hardwood glazed and skeleton shutters, open reabeted and prepare to received glass fitted with cut and mitred beads for secuing glass for ventilators complete all as specified and directed.
S&F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.
S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty / wooden beeding in square n. exc 0.5 sqm each panes complete all as specified and directed.
Supply & fixing solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.
Supply & fixing factory made solid pannel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification and drawing.
M&Lfor 15mm thick rendering on fair faces of stone masonry work surfaces in cement mortar 1:4, finsihed the surfaces even and fair complete all as specified and directed.
M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6, finished even and smooth without using extra cement complete all as specified and directed.
M&L for 5mm thick rendering on concrete surfaces in cement mortar 1:3, as in ceiling, finsihed the surfaces even and smooth without using extra cement complete all as specified and directed.
M&L for preparing of new surface of plaster and applying two coats of white wash on wall complete all as specified and directed.
M&L for prepartion of newly plastered wall surfaces of any description applying two coat of cement base paint over a coat of primer complete all as specified and directed.
M&L for preparing of new surface of plaster and applying two coats of white wash on ceiling complete all as specified and directed.
M&L for preparation of new untreated wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and painting with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.
M&L for 75mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregates as in sub-base complete all as specified and directed.
M&L for 25mm thick Cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregates as in sub-base/under flooring complete all as specified and directed.
M&L for Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) are of each tile exceeding 0.11 Sqm but n exc 0.18 sqm in floors set and jointed in neat cement slurry over 15 mm thick screed bed or bedding layer of cement mortar 1:4, and pointed in white or coloured cement to match complete all as specified and directed.
M&L Glazed ceramic White tiles in vertical surface 300x 200x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including Rendering 10mm thick to receive the tile in cm 1:3 complete all as specified and directed.
M&L for 60mm thick interlocking paver block with grey cement and pigment of any size and shape confirming to IS 15658-2006, M-35 Grade as approved by GE laid in flooring and joints filled/broomed with fine sand complete all as specified and directed.
M&L for Sand filling under floors or in foundations complete all as specified and directed.
M&L for providing, cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges, in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, kerbs , and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.
S&F 250mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.
S&F for 100mm long butt hinges mild steel medium weight cold rolled complete all as specified & directed
S&F 125mm aluminium handles, cast type, anodised and pattern/design as approved complete all as specified and directed.
S&F 100mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.
S&F 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.
M&L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specifeid and directed.
M& for providing cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate), 75 mm thick as in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair on top without using extra cement with 6mm wide joints throughout the thickness of plinth protection in concrete bays complete all as specified and directed.
S&F puff water tank 500 litres capacity, insulated cylindrical vertical type double layer duly filled with glass wool with closed top hoisted and to resist in temprature -30 degree to +35 degree celcius fixed in position with all fittings over PCC platform complete all as specified and directed.
S&F vitreous China squatting pan 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specifeid and directed.
S&F Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specifeid and directed.
M&L for applying evenly a tack coat of in dustrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed.
M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified.
S&F wash down water closet (Pedestal Pattern) (excluding flushing cistern and flush pipe) white including connection to drain and to flushing pipe, antisyphonage pipe etc, flush pipes of size 630 x 450 mm with integral foot rest to pedestal pan, including all joints, complete assembled all as specified and directed.
S&F vitreous china wash basin, white, flat back, size 550x400 mm including brackets, cutting pinnning in ends of brackets or erecting stand but exclusive of fixing, complete assembled, 32mmbore waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.
S&F 20mm outer diameter 3-layer PP-R polypylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. all as specified and directed.
S&F 15 mm bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.
S&F PVC connection of 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.
S&F 15mm pillar taps, cast copper alloy, chromium plated screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts, screwed for iron pipe complete all as specified and directed.
S&F stop/angle cock 15mm bore, fancy type cast copper alloy chromium plated, screwed down, high pressure, with crutch or butter- fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.
S&F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets capacity 10 ltrs complete all as specified and directed.
M&L of 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.
S&F brass CP tubular Towel rail 20 mm dia between flanges complete all as specified and directed.
S&F chromium plated shower roses 125mm size, fancy type with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed.
S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed.
S&F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.
S&F of 32 mm PVC waste pipe for WHB complete all as specified and directed.
S&F 20mm bore dia of pipe Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.
S&F PVC (SWR) 110mm dia mtr pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.
S&F PVC (SWR) 75mm dia mtr pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.
S&F PVC (SWR) 110mm dia mtr bends any radius complete all as specified and directed.
S&F 75 mm PVC (SWR) bend any redius complete all as specified and directed.
S&F 110 mm PVC (SWR) junction (single T) equal or unequal complete all as specified and directed.
M&L for RCC Septic tanks Designed to carry sewage and sludge water excavation in any type of soil, foundation In PCC 1:4:8, RCC M-30 design mix in walls base slab, baffle walls and brick work in CM 1:4, RCC Slab covers including RCC precast Manhole cover having 6mm plate embedded all around/ fibre reinforced cover with angle iron frame Vent shaft and sludge chambers etc., complete for 10 users as per drawing No CELZ/TD/ST-3010 sheet (1/3 to 3/3) dated 22 Dec 2022.
M&L for PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) in foundations, filling and mass concrete, complete all as specified and directed.
M&L for plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in bed to drain pipes incl packing under and hauching against the side of pipes after they are laid and tested for 150mm bore NP-3 Pipe complete all as specified and directed.
M&L for RCC NP3 150 mm diameter Pipes laid in trenches on concrete bed and jointed complete with collars all as directed. (Note: Excavation, earthwork , concrete bed shall be measured and paid seperately)
M&L for PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) in surface channels and drains complete including weathering, slightly rounded or chamfered angles and throating and necessary formwork all as specified and directed.
M&Lfor 15mm thick rendering on fair faces of stone masonry work surfaces in cement mortar 1:4, finsihed the surfaces even and smooth using extra cement including mixing of water proofing admixure as per manufacturer instructions all as specified and directed.
M&L Pre-cast RCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in manhole cover slab set in CM 1:6 complete all as specified.
M&L Point wiring with 1.5 Sqmm (nominal area) copper conductor FRLS cable (multi-stranded) PVC insulated and unsheathed electric cable 1100 volts drawn through PVC casing and caping of suitable size (as per conductor run) with all fittings and accessories and including PVC insulated unsheathed electric cable 1100 volts 1.5 Sqmm (multi-stranded) copper conductor single core (green colour) as continuous earth wire connected to common earth dolly including 50mm deep box made out of 2nd class hard wood board of suitable size and shape and other boxes for mounting light fittings etc covered with 3mm thick plastic laminated Hylum ISI marked for following complete all as specified and directed. Note:- Screw used for fixing TW baords, casing and caping ceiling rose, square blocks etc should be nickel cadmium screws.
(a) One light point/ Exhaust fan controlled by one 5 Amps one way switch
(b) One 3 pin socket outlet 5 Amps on independent board
(c) One 3 pin socket outlet 5 Amps on same board
M&L point wiring for power point with 4.0 sqmm (nominal area) copper conductor FRLS cable ( multi-stranded) PVC insulated and unsheathed cable conductor 1100 Volts drawn through PVC casing capping of suitable size(as per conductor run) with all fittings and accessories and including PVC insulated unsheathed electric cable 1100 volts 2.5 Sqmm (multi-stranded) copper conductor single core (green colour) as continuous earth wire connected to common earth dolly including 50mm deep box made out of 2nd class hard wood board of suitable size and shape and other boxes for mounting light fittings etc covered with 3mm thick plastic laminated Hylum ISI marked for following complete all as specified and directed by Engr-in-Charge. Note:- Screw used for fixing TW baords, casing and caping ceiling rose, square blocks etc should be nickel cadmium screws.
S&F Switch piano flush button single pole one way 5 Amps, 240 Volts complete all as specfied and directed.
S&F socket outlet 2 in 1, 3pin, 5A(multipurpose) sutable for 2 pin/3 pin plug flush type complete all as specified and directed.
S&F switch socket combination 2 in 1, 3 pin, 5/15 Amps, flush type (multipurpose). Complete all as specified and directed.
S&F Ceiling rose surface backelite ISI marked with 3 terminal including connecting and testing complete all as specified and directed.
S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.
Supply and fixing Rechargeable LED Bulb energy saver 9 W, B22(220-240 V) 50 hz, 6500k fast charging 2200mAH battery including, white color all as specified and as directed. Make:- CG/Phillips/Havells
Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.
S&F surface and wall mounted LED batten with polycarbonate housing and integrated electronic driver tube light fitting 20W, 4 ft long, 220 Volts , and connecting to ceiling rose with three core twisted flexible copper cable of suitable size complete all as specified and directed.
S&F LED light fitting 1x10W bulkhead, 220 Volts and connecting to ceiling rose with three core twisted flexible copper cable of suitable size complete all as specified and directed.
S&F MCB DB sheet enclosure, Double door type, single pole and neutral 240V with 200 Amp rated bus bar suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete confirming to IP 42/43 without MCB and with enclosure blank plates for unused way suitable for 8 way complete all as specified and directed.
Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning all as specified and directed.
Supply and fixing MCB SPN 240V, 10KA 'C' curve 40-63 Amp current carrying capacity in the MCB DB complete with connection testing and commissioning all as specified and directed.
M&L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6mm thick burried directly in ground not less than 2.25m deep below normal ground level (with the top edge of the plate not less than 1.50 m below the normal ground level) connected to GI earth wire 4 mm by means of GI bolts, nuts, check nuts and washers of GI all as shown in electrical plate No.3 of SSR Part-I connected to earthing test point with and including necessary excavation and earth work in any strata PCC pit 1:3:6 type C-1, 20mm bore medium grade GI pipe for watering 15mm bore light grade pipe for GI wire protection and funnel including 40mm thick RCC slab cover and testing on completion all as specified and as directed.
Exhaust fan with louvers of size 300mm sweep, 1200 RPM, 230 volts (single phase) plastic type complete with bolts, nuts & washers, embedded in the wall including provisioning of three core flexiable copper cord of size 23/0.0076 of required length from ceiling rose or connector to Exhaust fan for connection, complete all as specified & directed
S&F GI bracket for street light of 32mm bore GI pipe (medium grade of length 1.5 meter), bend to shape including providing2x pairs of MS flat iron clamp (of suitable size, made out of 40mm x 5mm mild steel flat) with nuts, bolts and washer of suitable size, including applying two coat of red oxide primerand one coat of aluminium paint complete all as specified and directed.
Supply and fixing LED bldg security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete making all necessary connection with suitable capacity of 3 core circular cable complete all as specified and directed.
M&L for sub Main Wiring in PVC Conduit with two single core PVC insulated unsheathed multistranded flexible copper conductor cable of size 2x2.5 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor of size 1.5 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in existing conduit complete all as specified and directed.
M&L for 1100 volts grade heavy duty cable with PVC insulated aluminiuum stranded conductor served with an inner sheating of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 mtr apart including 4mm suspention wire one twin core 16 sqmm solid conductor all as specified and directed.
Supply, laying, fixing, passing through pipe or laid in trenches and testing underground XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross section area 2 core 16 sqmm all as specified and directed.
M&L for sand cushioning to underground cables using new dry river sand laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete, punned to 18cm, complete all as specified and directed. Note : Punned thickness of 18cms shall be measured for payment.
M&L Un-reinforced precast factory made concreate cable covers, class LV type-I, with flat size 250x150x40 mm Complete all as specified and directed.
Supply, Install Testing & Commissioning of self supporting totally enclosed double door at front, LT feeder piller compartmentalised design, dust and varmin proof of size 600 mm(Height) x 600 mm(Length) x 450 mm(Width) suitable for 440 Volt 3 phase 4 wire system made out of 3.15 mm thick CRCA sheet and built upon regid frame work having front and rear hinged doors with neoprence rubber gasket including danger plate, earthing strip point and, ventilation louvers at the rear side, bottom detachable gland plate complete with suitable size of Zinc/Cromium plated and nuts, bolts; and washers etc. The pannel shall be synthetic enamelled painted and the control circuit diagram shall be with colour code solid conductor copper 1.5 sqmm cable for easy identification including incomming/outgoing cable holes at the bottom, complete after taking down the old unserviceable one. The Panel shall be emmbeded with 75 x 6 mm MS Angle Iron frame and to be grouted with PCC foundation (1:2:4 ) type B2 upto a height of 50 cm from normal ground level complete all as specified and directed and comprising of the following :- (a) Aluminium bus bar 200 amps - 04 Nos, supported with suitable size of heavy duty porcelin stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral. (b) MCB of SPN, 63 A, 10 KA, with breaking capacity of 25 KA, Make : L & T/Havells - 01 No
item no 104.00 contd... (c) MCB of SP, 06 to 32 A, 10 KA, Make : L & T/ Havells - 02 No (d) LED Indicating lamps for Main Supply indicating R', Y' B' - 01 Set of 3 (e) Digital Voltmeter (Make AE/L&T) - 01 No (f)Current Transformer having Ratio 400/5, 15 VA - 01 Set of 3 (g) Digital Ammeter ( Make(AE/L&T) - 01 No
Supply and laying/fixing, GI pipe medium grade 40 mm bore (dia)including all type fittings fixed on walls/to poles with clamps /laid in trenches as cable protection all as specified and directed.
Supply, installation and testing LED Solar security light fitting 36 Watt alongwith panel capacity 100 W 1 No for 12 volt lightening crystalline silicon adding aluminium frame, water proofing IP-68 automatic light control system switch on automatically with light sensor, over charging / discharging protection, reverse, connection, protection, indication, lamp for charging ON 'green' and low battery 'Red', hot dip galvanized platic coated steel Q235 tampered pole 6 mtr height complete. (Excavation, earth work & PCC shall be measured separately)
M&L for cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) for base of foundation of pole / stay including form work etc. all as specified and as directed.
M&L for PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in coping of pole, including necessary form work complete all as specified and directed.
S&F of electrical water heating system/Hamam of capacity 500 Ltrs with boiler and Glass wool insulation of 25mm thickness to be provided between outer and inner sheet. 100mm dia MS pipes is to be be fitted in centre which will act as heater. One direct water connection for inlet of water. Funnel for pouring water manually to be provided. One over flow pipe, 2 outlet of hot water from the boiler to be provided. Inner chamber is to be painted with boiler paint and external steel surface are to be painted with two coats of synthetic enamel paint over a coat of red oxide incl necessary components like stand for hamam complete all as specified and directed.
M &L for Sheet metal enclosures with socket plug top and MCBs, single pole and neutral enclosure with a 2 pin and earth plug and socket complete with one single pole MCB SPN 20Amps, 240V complete all as specified and directed.
M&L for Elestometric Nytral rubber insulation to PP-R pipes suitable for 25mm outer dia 28/19mm thick with chiken wire mesh wire netting 25mm gauge, 20mm mesh with 0.01mm aluminium foil including jointing and fixing material such as solvent adhesive SR-998 complete all as specified and directed.
Supply and fixing PP-R gate valve (brass insert) for 25 mm dia pipe as per requirement of the site all as specified and directed. Make : SFMC/Prince or equivalent.
Supply and fixing PP-R Ball valve (brass insert) for 25 mm dia pipe as per requirement of the site all as specified and directed. Make : SFMC/Prince or equivalent.
M&L for Making connection of PP-R distribution branch with PP-R main of 16 to 40mm outer dia pipe by providing and fixing tee including cutting and making fusion joint etc, complete all as specified and directed.
M&L for platform for Hamam of size 2m x 2m x 1.2m (clear height with additional 150mm thick pcc 1:3:6 type C-2 foundation below ground level), made out of 23cm brick masonary in cement mortar 1:6 (below ground level), hollow space to be filled hard core of size n.exc 63 mm, deposited, spread and levelled in layers not exceeding 15cm thikness, watred and well rammed with a 100 mm thick cement concrete 1:2:4 type B-2 as in floor of platform, plastering in CM 1:4 including protection with XPM, gate and chain link fencing rail around the platform with angle iron frame upto 1.20m clear height supports grouted in PCC 1:2:4 type B-1 foundation complete all as specified and directed.
M/S ASGAR ALI TIMBER SHOP (BID ID -3072976)
M/S MOHD MUSSA (BID ID -3073192)
M/S GHULAM MOHAMMAD CHATAPA (BID ID -3073251)
MEHDI ALI (BID ID -3073294)
M/S SHAMSHER ALI SUFI (BID ID -3073532)
THINLES OTZER (BID ID -3073219)
CHHIRPON BUILDERS (BID ID -3073307)
M/S ASHRAF HUSSAIN (BID ID -3073188)
stage.html
html • 0.07 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .