REPAIRS TO DRAIN, PATH, CULVERT, FENCING, COMPOUND WALL AND MISC WORKS AT DOMESTIC AND SMQ AREA UNDER GE (AF) HASIMARA

Amount

Demolition of Bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer) laid dry or laid dry and pointed complete all as directed by the Engr-in-Charge.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc stacking the serviceable bricks after removing mortar and cleaning for re-use and disposal of debris and rubbish to a distance n.exc 100m as directed by the Engr-in-Charge.

Demolition of un-reinforced cement concrete in ground floors and pavings n.exc 15cm thickness, (Below or above Ground level) and disposal of debris and rubbish to a distance n.exc 100m complete all as directed by the Engr-in-Charge

Demolition of reinforced cement concrete in any position not otherwise specifically provided for complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed

M & L for Brick work with sub class 'B' bricks, laid flat, in drains, etc bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 complete all as specified and directed.

All as per item No. 06 above but except brick complete all as specified and directed. (Note: Old serviceable bricks as obtained from demolition shall be re-used at site after cleaning and removing mortar etc)

M & L for Brick work with sub class 'B' bricks, laid on edge, in floors, drains, etc bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 complete all as specified and directed.

All as per item No. 08 above but except brick complete all as specified and directed. (Note: Old serviceable bricks as obtained from demolition shall be re-used at site after cleaning and removing mortar etc)

M & L for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in cement mortar 1:4 as in half brick thick walls complete all as specified and directed.

M & L for Brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in surface channel, drains etc complete all as specified and directed.

Extra for forming fair finished to concrete surface of drain 30cm inner girth in cement including forms, mould, mitred/stopped etc complete all as specified and as directed.

Add or deduct for each 25mm girth or part thereof over or under 30cm including form mould, mitred/stopped etc. complete all as specified and as directed.

M & L for plain Cement Concrete 1:2:4, type B-2 (using 40 mm graded crushed stone aggregate) as in walls, retaining walls, ballast walls and the likes any thickness above top of footings including attached pilasters and buttreses complete all as specified and directed.

M & L for use & waste Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in cover slab of drain, etc and set in cement mortar 1:4 including necessary form, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

S & F TMT steel bars 6mm to 8mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M & L for Plain cement concrete 1:2:4, type B-1, (using 20 mm graded crushed stone aggregate) as in benching, coping, bed plate, lintel upto 1.5m span cast in situ including necessary form work complete all as specified and directed.

M & L for Raking out joints/ pointing to brick work in walls or to bricks on edge in floors, surface channels, roofs, etc in cement mortar and Flush pointing to brick on edge pavings in cement mortar 1:4 complete all as specified and directed.

M & L for Raking out joints/ pointing to brick work or brick tiles, laid flat, in floors, surface channels, roofs, etc in cement mortar and Flush pointing to bricks laid flat or brick tiles in pavings in cement mortar 1:4 complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

M & L for Rolled Mild Steel Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S & F in repair Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and as directed.

Re-straining and re-securing of Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings including making good staples etc complete all as specified and as directed. (each line wire to be measured)

Dismantling fencing wire mesh, any type complete complete all as specified and directed.

Supply only chain link MS galvanised fencing, any size or type complete all as specified and directed. (Note: Weight of chain link shall be ascertain by a BOO to be convened by Accepting Officer)

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed

Fixing only old serviceable chain link fencing as obtained from serial item No. 26 above including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed

S & F Mild steel screw bolts of 11 to 15 mm diameter of shank (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm and n exc 10cm long complete all as specified and directed.

S & F in repair concertina coil fencing with punching tap concertina coil 960mm dia 13 mtres openable length having 53 Nos rounds per 6 metres length, single coil, fixed on wall with existing angle iron 'Y' shaped with horizontal reinforced barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing, stud tied with GI staples and GI clips to retain horizontal including necessary bolts or GI barbed wire tied to angle iron complete all as specified and as directed. (Note: (i) Weight of concertina coil shall be ascertained by a BOO to be convened by Accepting Officer (ii) Barbed wire shall be measured and paid seperately under respective items here-in-before)

All as per serial item No. 31 above but fixing only in repair of any dia complete all as directed. (Note: Old serviceable loosed concertina coil shall be refixed at site after taking down complete)

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and fair without using extra cement complete all as specified and directed.

M & L for preparing newly plastered surfaces of walls, etc and applying three coats of white wash complete all as specified and directed.

M & L for 100 mm thick, Plain Cement Concrete 1:2:4, type B-2 (using 40mm graded crushed stone aggregate) as in footpath/hardstanding, etc and finishing the cement concrete surfaces even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

Excavating in post holes (or similar holes) each n. exc 0.5 Cum, in soft/loose soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25cm, watering and removing surplus soil to a distance n. exc 50m and making good surface in soft/loose soil complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

Disamntling RCC post or struts any section, including taking out embedded portion in natural ground and making good disturbed ground including cleaning and cutting of grass, shrubs, bushes, etc complete all as specified and directed.

M & L for mild steel round bar 10mm dia and over cut into length, bend to shape required including cranking bending spirally for hoping as in tie bar for fixing chain link fencing complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for Reinforced Cement Concrete 1:1.5:3, Type A-1 (Nominal Mix) (using 20 mm graded crushed stone aggregate) as in columns, pillars, posts and struts complete all as specified and directed.

S & F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

M & L for use & waste Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work, vertical or to batter complete all as specified and directed.

M & L for use & waste Formwork to sides of pillars, posts, struts, piers, columns and stanchions for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, not otherwise described, n. exc.10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S & F TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S & F Mild steel TMT bars 5mm dia and over upto and including 10mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

Demolition of un-reinforced cement concrete in any position not otherwise specifically provided for complete all as specified and directed.

M & L for 75mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in footpath, road side paving/hardstanding etc, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Material and labour for 25 mm thick pre-polished cement concrete chequered tiles, glossy finish , smooth in design , compressive strength 300 kg/Sqcm, ISI marking (IS-13801-1993), set, jointed in neat cement slurry and pointed with white cement mixed with pigment to match laid over and including 20mm thick screed bed in cement mortar 1:6 including dismantling of damaged/unserviceable tiles complete all as specified and directed

M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed.

M & L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finishing cement concrete surface even and fair without using extra cement complete all as specified and directed. Note: An amount of Rs. 69720.00 on account of credit schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

M/S RATHIN ENTERPRISES

M/S SARDAR MAL NAHATA

JOGINDER KUMAR GOYEL

M/S DEY ENTERPRISE

M/S ASHOK ENTERPRISE

CONSTRUCTION SHELTER

M/S ANIL KUMAR BAUL