Special Repair of Non Residential Buildings in GMCH Sector 32, Chandigarh for the year 2025-26 (Block-B)

Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m. DSR 2.30

All kinds of soil DSR 2.30.1

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : DSR 4.1

1:2:4 (1 cement : 2 coarse sand (zone-lll) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 4.1.3

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) DSR 4.1.10

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. DSR 8.31

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. DSR 9.83

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : DSR 9.96

300x16 mm DSR 9.96.1

250x16 mm DSR 9.96.2

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : DSR 9.97

150x10 mm DSR 9.97.4

100x10 mm DSR 9.97.5

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. DSR 9.101

Twin rubber stopper DSR 9.101.2

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : DSR 11.19

Ordinary cement without any pigment DSR 11.19.4

Kota stone slab flooring over 20 mm (average) thick base laid over andjointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : DSR 11.26

25 mm thick DSR 11.26.1

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.DSR 15.23

For thickness of tiles 10 mm to 25 mm DSR 15.23.1

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. DSR 15.56

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. DSR 15.60

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : DSR 21.1

For fixed portion DSR 21.1.1

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) DSR 21.1.1.1

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : DSR 21.1

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) DSR 21.1.2

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) DSR 21.1.2.1

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge. DSR 21.2

Pre-laminated particle board with decorative lamination on both sides DSR 21.2.2

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): DSR 21.3

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) DSR 21.3.2

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineerin-charge DSR 21.4

With stainless steel cover plate minimum 1.25 mm thickness DSR 21.4.1

Providing and fixing wooden storage cabinet under work top 2'-0" high & 2'-0'' deep consisting of 19mm thick commercial board ISI marked with 6mm thick commmercial ply on back side including 1 Nos. Horizontal shelf ( as per sketch) . The front side of the cabinet shall be provided with 1mm thick laminate of approved shade and inner surface shall be provided with 0.70mm thick laminate including 20mmx 6mm thick second class teak wood lipping on exposed edges of the board. The rate further include the cost of piano type hinges , S.S handles 4"size, aluminium hasp & staple, magnatic catcher, stainless steel adjusters / lifters, fevicol, nails , screws complete fixed in position tothe entire satisfaction in the Engineer-in-charge. ( Front elevation area shall be measured for payment). NS

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. NS

With frosted glass panes of 5 mm thickness NS

Providing & Fixing of Factory made Fine Finished Cylindrical Bollard 150mm dia Fiber Reinforced Plastic moulds of size 950 high over ground level and 300mm below G.L. made with M:35 mix concrete design using 1250mm long 4 nos. 10mm dia TMT steel bars, 6mm dia stirrups @ 150mm c/c consisting 2 cuts of 75 mm high at top for retro reflector sheet type-IV, fiber reinforcement plastic moulds fixed in ground with C.C. 1:2:4 block of size 300x300x300 with base of C.C.1:5:10 block of size 300x300x100mm complete in all respect as per drawing / sketch and to to the entire satisfaction of Engineer-in-charge. NS

Providing and fixing pre laminated water resistant ACP Sheet of 5mm thick as per grade-I for aluminium doors, partition, sutters etc.complete in all respect and to the entire satisfaction of engineer in charge. NS

Repair of Existing Aluminium Door after taking Out the existing Frame completely and fitted with tie Rod horizontally for strenghthing the Frame & replacing the Hinges if required set right the door properly and refitted it in original position complete in all respect of the engineer-in-charge. NS

Dismentling of ceramic tiles carefully and scraping the plaster to making the surface clean for refixing the glazed tiles inlcuding removing of malba complete in all respect. NS

Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade. NS

15-18 mm thick mirror polished and machine cut edge Granite stone of any colour and shade NS

Extra for Cleaning on KOTA stone/ Chips flooring work wherever required to give high gloss finish complete in all respect to the engineer-in-charge. NS

Providing and fixing Aluminium American Handles ISI Marked anodised canodic coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour or shade , with nuts 8 screws , with nuts 8 scrtews etc. complete. size 200mm x 20mm NS

Please Enable Macros to View BoQ information