AS05224

MRL03-Halakura PMGSY Road to Bidyadabri Pt II via Mahadev Mandir

Item Rate BoQ

BoQ_Ver3.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Clearing and Grubbing Road Land Clearing and grubbing of Road land including up rooting rank vegetation grass, bush, shrubs saplings and trees of girth upto 300mm removal of stumps of trees cut earlier and disposal of unseviceable materials & stacking of serviceable material to be used or auctioned, upto a lead of 1000m including removal & disposal of top organic soil not exceeding 150mm in thickness as per Technical Specifications Clause 201. [SOR 25-26] [item No.2.2] (I) By Manual Means- (a) In area of non thormy jungle

Construction of embankment with material obtained from borrow pits,Construction of embankment with approved materials obtained from borrow pits with a lift up to 1.5m, transporating to site, spreading, grading to required slope and compacting to meet required of Tables 300.1 and 300.2 with a lead upto 1000m as per technical specification clause 301.5. [SOR 25-26] [item No.3.4] a) Private land

Construction of sub-grade and earthen shoulders Construction of sub-grade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporating to site, spreading, grading to required slope and compacting to meet required of Table 300.2 with lead upto 1000m as per technical specification clause 303.1. [SOR 25-26] [item No.3.14] (a) Private land

Construction of Granular sub-base (A) By mix in Place Method, Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. [SOR 25-26] [item No.4.1] (II) For Grading Material (Gr - II )

Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. [SOR 25-26] [item No.4.8] By Mechanical Means with 1 km lead

Prime-Coat (i) Low porosity Providing and applying primmer coat with bitumin emultion (SS-1) on prepared surcafe of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per technical Clause 502. [SOR 25-26] [item No.5.1]

Tack-coat (III) Providing and applying tack coat with bitumin emultion (RS-1) using emultion distributor at the rate of 0.25-0.30 Kg/sqm on the prepared granular surface tresated with primer & cleaned with hydraulic broom as per technical specification clause 503. [SOR 25-26] [item No.5.2]

Mix Seal Surfacing Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509. [SOR 25-26] [item No.5.11] II) By Mechanical Means B) Type B ii) Bitumen (S-65)

Trafic - Signs B. Semi Reflective Traffic Signs (1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5mm thick supported on a mild steel angle Iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x600mm, 600mm below ground level as per drawings and Technical Specification clause 801. [SOR 25-26] [item No.10.2] (ii) Warning Signs [600mm -Triangle]

Trafic - Signs B. Semi Reflective Traffic Signs (1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5mm thick supported on a mild steel angle Iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x600mm, 600mm below ground level as per drawings and Technical Specification clause 801. [SOR 25-26] [item No.10.2] (iv) Speed limit Sign [600mm -Cricular]

Trafic - Signs B. Semi Reflective Traffic Signs (1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5mm thick supported on a mild steel angle Iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x600mm, 600mm below ground level as per drawings and Technical Specification clause 801. [SOR 25-26] [item No.10.2] (iii) 800 mm x 600 mm rectangular.

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications. [SOR 25-26] [item No.16.34]

Road Markers/Road Stud with Lens Reflector Providing and fixing of road stud 100 x 100 mm die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS:873 (Part 4) 1973. [SOR 25-26] [item No.10.20]

Tack-coat for Speed Breaker (III) Providing and applying tack coat with bitumin emultion (RS-1) using emultion distributor at the rate of 0.25-0.30 Kg/sqm on the prepared granular surface tresated with primer & cleaned with hydraulic broom as per technical specification clause 503. [SOR 25-26] [item No.5.2]

Mix Seal Surfacing for Speed Breaker Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509. [SOR 25-26] [item No.5.11] II) By Mechanical Means B) Type B ii) Bitumen (S-65)

Kilometer Stone Reinforce cement concreter M15 grade kilometer stone of standard design as per IRC:8 fixing in position including painting and printing etc. as per drawing and technical specification clause 1703. [SOR 25-26] [item No.10.10] (ii)Ordinary Kilometer Stone (precast)

Kilometer Stone Reinforce cement concreter M15 grade kilometer stone of standard design as per IRC:8 fixing in position including painting and printing etc. as per drawing and technical specification clause 1703. [SOR 25-26] [item No.10.10] (iii) 200 m Stone (precast)

Providing and Fixing with with 'Logo' of PMGSY Project Providing and fixing of typical PMGSY informatory sign board with logo as per MORD specifications and drawing. Three MS plates of 1.6mm thick, top and middle plate will be welded with MS flat iron 25mm x 5mm x size on back on edge. The lower plate will be welded with MS angle iron 25mm x 25mm x 5mm. The anfle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly embeded in cement concrete M15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The topmost dimond plate will be welded to middle plate by 47mm X 47mm of 12 SWG steel plate tube. All MS will be stove enameled on both sides. Lettering and printing arrows, borders etc. will be painted with ready mixed synthetic emnamel paint of superior quality in required shade and colour. All sections of framed posts and steel tuube will be painted and two coats of epoxypaint as per specification clause 1701 and Annexure 1700.1 [SOR 25-26] [item No.10.16]

Providing and fixing of typical Logo Board with PMGSY Logo as per MORD specifications and drawing. 1 nos. 1.6mm thick MS sheet duly welded with 5mm thick steel plate on back on edges. The 1 nos. steel plate will be welded horizontally with 1 nos. 75mm x 75mm of 12 SWG |sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The 1 no steel plate will be welded vertically to 1 no. 75mm x 75mm of 12 |SWG sheet tubes posts duly welded to vertical tubes. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloue. All sections of framed posts and |steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1. [SOR 25-26] [item No.Analysis]

Providing and fixing of typical Citizens Information Board with Logo as per MORD specifications and drawing. Two nos. 1.6mm thick MS duly welded sheet with 5mm thick steel plate on back on edges. The 4 nos. steel plate will be welded horizontally with 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 600mm x 600mm x 750mm, 750mm below ground level. The 2 nos. steel plate will be welded vertically to 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly welded to vertical tubes. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloue. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 Citizen Information board and maintenance information board are considered. [SOR 25-26] [item No.Analysis]

Setting Out (v) Typical benchmark as per Drawing 200.1. [SOR 25-26] [item No.1.16]

Setting Out (vi) Typical reference pillar as per Drawing 200.2. [SOR 25-26] [item No.1.16]

Surface Drains in Soil Construction of unlined surface drains of average cross-sectional area 0.40 sqm in soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment with a lift upto 3m and lead of 50 m (average lead 25 m) as per Technical Specification Clause 307. [SOR 25-26] [item No.3.19] Manual Means

Turfing with Sods Furnishing and laying of the live sods of perennial turf forming grass on embankment slope, verges or other locations shown on the drawing or as directed by the Engineer including preparation of ground, fetching of sods and watering as per Technical Specification Clause 309. [SOR 25-26] [item No.3.12]

Providing and laying one layer of Non-Woven geotextile of minimum mass per unit area of 280gms/sqm.having minimum roll width of 5.0m treated with carbon black with physical properties as given in clause no 702.2.3. over 25mm thick compacted sand layer on a prepared subgrade as a filter media with necessary overlaps as per drawing and technical specification and as directed by the Engineer in charge complete. [SOR 25-26] [item No.16.4]