ADDN ALTN TO COOK HOUSE AND DINING HALL BLDG NO P 502 5 INS TUNIR AND SPL REPAIRS OF LT XLPE UG CABLE FROM AVII TO BLDG NO P 1171 AT NAVAL STATION KARANJA

Notes : Please refer schedule 'A' notes before quoting the tender.

JOB (A) B/R WORKS

Taking down cement plaster on brick walls or stone walls etc including raking out joint, hacking for key, scrubbing down with water etc including removing debris as directed upto a distance not exceeding 500m complete all as specified and directed.

Demolition of pre-cast concrete block masonary built in cement mortar including all quoins, arches, pillars, etc. and pre cast concrete articles including removing debris as directed upto a distance not exceeding 500m complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks in 10cm width in type B1 1:2:4 (using 20mm graded stone aggregate) and setting in cement mortar (1:6) complete all as specified and directed.

Supply only water proofing liquid compound complete all as specified and directed.

M&L for ready mix plaster for rendering 15mm thick on fair faces of brick/concrete surfaces, finished even and smooth without using extra cement (WPC to be measured and paid separately) complete all as specified and directed.

M&L for ready mix plaster for rendering 10 mm thick on fair faces of brick work or concrete surfaces of walls finished even and smooth with out using extra cement complete all as specified and directed.

M&L for use ready mix plaster for rendering 5 mm thick on ceilings and finishing the surface even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered surfaces on ceiling of any description not otherwise described over 10cm width or girth and M&L for applying three coats of white wash complete all as specified and directed.

Preparation of new plastered surfaces on walls of any description not otherwise described over 10cm width or girth and M&L for applying two coats of oil bound distemper over & including a coat of alkali resistant primer, complete all as specified and directed.

Preparation of new or previously untreated plastered surfaces of walls and M&L for applying two coats of acrylic antifungal paint exterior grade paint plain or camoflage pattern over & including one coat of primer complete all as specified and as directed.

Complete removal of existing treatment from old decorated plastered surfaces of walls & ceilings by Vacuum based sanding machine, removal of nails etc & filling cracks/hole with putty and M&L for applying wall care putty upto 2 mm thick (multipurpose mixer shall be used for uniform and proper mixing of putty) and M&L for applying two coats of oil emulsion distemper white or coloured over & including a coat of approved primer by auto roller complete all as specified & directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store including removing debris as directed upto a distance not exceeding 500m complete all as specified and directed.

M&L for non skid ceramic coloured tile, 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38 Sqm as in floors over & including 20 mm thick screed bed in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the tile complete all as specified and directed.

M&L for Vitrified ceramic coloured tiles 10mm thick (Square/ Rectangular) polished area of each tile not exceeding 0.36 Sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including screed bed or bedding layer 20mm thick in CM 1:4 for laying floor finishes complete all as specified and directed.

M&L for Vitrified ceramic coloured tiles 10mm thick as in vertical surfaces such as skirting, dado etc jointed in neat cement slurry over & including 10mm thick cement mortar (1:4) pointed in white or coloured cement complete all as specified and directed.

Dismantling of stone slabs & tiles of any description or thickness in floor aprons, cills etc laid bedded & pointed in any mortar including removing debris as directed upto a distance not exceeding 500m complete all as specified and directed.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over & including screed bed 15mm thick in CM 1:4 complete all as specified and directed.

M&L for Machine cut cudappah stone slab 20-25mm thick over & including 20mm thick cement screed in CM 1:3, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Machine cut Kota Stone slab flooring 20-25 mm thick; laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over & including 20mm thick screed bed or bedding layer of mortar in CM 1:6 for laying floor finishes complete all as specified and directed.

M&L for green marble 18 to 20 mm thick (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking plateforms and like in CM 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

Taking down chowkats or frames including shutter (without taking off shutters from the frame) area exc 1.50 Sqm but not exc 4 Sqm each, complete all as specified and directed.

S&F Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm (double rebated) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with & including MS hold fast/ lugs/ SS dash fasteners of required dia and length, complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with & including necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.

S&F 35mm thick 2nd class HW, glazed and skeleton shutters open rebated and prepared to receive glass / gauge (without sash bar) edges of forming plain chamfered or rounded fitted with cut and mitered bead for securing glass / gauge etc. size of shutter as per SSR part-1 section 8 clause 8.24(a) complete all as specified and directed.

S&F door frame made from seasoned teak or equivalent high-grade hardwood, kiln-dried to maintain dimensional stability and treated for termite and moisture resistance, minimum section 125 × 100 mm, reinforced with concealed steel rods, complete all as specified and directed.

S&F premium handcrafted antique-style heavy-duty door shutter made from seasoned teak or equivalent high-grade hardwood as approved, kiln-dried to maintain dimensional stability and treated for termite and moisture resistance; shutter thickness shall be 50 mm with double-panel construction and cross-bracing for rigidity; traditional mortise-and-tenon joinery, dowelled reinforcement, and resin bonding are required to ensure long-term durability; door surface shall feature deep-relief hand-carvings inspired by temple architecture, including motifs such as lotus, peacock, or geometric latticework, each panel requiring extensive artisan labor; finish shall be multi-layered antique patina achieved through natural oils, wax polish, and distressing techniques to replicate centuries-old heritage doors, complemented by custom-forged brass hardware in antique finish for hinges, locks, and handles; protective treatments shall include eco-friendly termite resistance, marine-grade coatings for moisture and UV protection, and integrated weatherstrips for exterior durability; aesthetic detailing shall include ornamental studs, beveled edges, burnished accents, and rich golden-brown teak tones with darker shading for depth; installation shall be carried out with & including stainless steel fasteners and chemical grout, ensuring plumb, level, and square alignment; contractor shall provide samples of carving and finish for approval, submit shop drawings prior to fabrication, and guarantee a minimum 10-year warranty against termite, warping, and joint failure, complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain cupboard /Wardrobe 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/sqmm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with & including necessary full body threaded star headed counter sunk S.S screws,complete all as specified and directed.

S&F 'L' Bihari hydraulic 0 crank, auto hinges 180 degree openable, stainless steel hinges 125 x 63 mm long bright polished fix to steel chowkhat/timmer frame work with screw or nut or bolt complete all as specified and directed.

S&F in repairs magnetic catcher 55 x 29 mm size for continuous opening and closing of doors shutter like use for door megnet lock, cupboard magnetic lock, wardrobe, and similar use incl all fitting like screw complete all as specified and directed.

S&F Extruded brass handles, fabricated type polished, 100mm long, complete all as specified and directed.

S&F SS butt hinges 100mm long medium weight, cold rolled mild steel and fixed, complete all as specified and directed.

S&F Butt hinges 125 mm, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11, complete all as specified and directed.

S&F 150 mm long extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

S&F 200 mm long Extruded brass handles, fabricated ornamental type and polished, complete all as specified and directed.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple bolt type and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed.

S&F 300mm Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed, complete all as specified and directed.

S&F 150mm long Aluminium, anodized barrel tower bolts of extruded section and fixed, complete all as specified and directed.

S&F 200 mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed, complete all as specified and directed.

S&F150mm size (Overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed in floor complete all as specified and directed.

Preparation of new wooden surfaces over 10cm width or girth, not otherwise described and M&L for applying two coats of synthetic enamel paint over & including a coat of pink primer, complete all as specified and directed.

S&F in repairs aluminium door/window/ventilator/partition, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame & necessary jointing cleats, glazing clips, powder coated aluminium snap beading, screws etc, complete and also including powder coated aluminium fittings such as stainless steel hinges, tower bolts, hooks & eyes, peg stays and handles, concealed star lock for aluminium window, Mortice lock vertical type size 100mm 04 lever for door, rubber beading suitable for fixing 4mm / 5mm thick glass in aluminium window / doors including connected items, with and making good to the disturbed portion with its original specifications including taking down existing members/frame any position complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing complete in square not exc 0.50 sqm each, complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing in square exc 0.50 sqm each, complete all as specified and directed.

S&F powder coated aluminium grill of design DG 104 pattern made out of 10mm dia rod fixed with and including standard aluminium frame of F section of size 23.40mm x 15.30mm & 1.4mm thick all as per manufactures instructions complete all as specified and directed.

S&F in repairs counter type vitreous china wash basin white, flat back, size 550 x 400 mm or equivalent including brackets, cutting for and pinning in ends of brackets or erecting stand with & including PTMT 32mm waste coupling and waste pipe, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for including removing debris as directed upto a distance not exceeding 500m complete all as specified and directed.

Separating, scraping and cleaning of reinforcement (Demolition of concrete measured separately) complete all as specified and directed.

Supply, hoisting and fixing of rotational moulded polyethylene water storage tanks 1000 litres capacity (cylindrical vertical with closed top) colour as approved, three layered construction, hoisted and fixed in Position all as specified in MES Schedule Part-I, with & including connecting the overflow drain out, inlet and out pipes, tank nipple, elbow, bend, unions, sockets, float vale, gate valve etc complete all as specified and as directed.

Supply, hoisting and fixing in repairs rotational moulded polyethylene water storage tanks 2000 litres capacity (cylindrical vertical with closed top) colour as approved, three layered construction, hoisted and fixed in Position all as specified in MES Schedule Part-I, with & including connecting the overflow drain out, inlet and out pipes, tank nipple, elbow, bend, unions, sockets, float vale, gate valve etc complete all as specified and as directed.

S&F in repairs float valve of PTMT with polythene ball and rod for 25mm dia pipe complete all as specified and directed.

S&F in repairs CPVC water tubing 25 mm bore pipe, SDR 11 including provision of all fittings and connected completed in concealed and surface, along with primer & solvent cement for joint as per ASTM D 2564, pipe material shall be as per ASTM D 1785, fitting/ flanges shall be as per ASTM D2467, in concealed and surface complete all as specified and directed. Note:- Pipe and fittings made from CPVC shall be clearly marked with manufactures name and trade mark. manufacturer test certificate (MTC) shall be provided.

All as per BoQ Serial Item No.56.00 above but 20 mm bore CPVC pipe, complete all as specified and as directed

S&F in repairs 15 mm bore Pillar tap cast copper alloy fancy type with capstan heads, chromium plated Fancy type screwed down high pressure with long screws shanks and nut, complete all as specified and directed.

S&F in repairs 15mm bore stop cock or angle valve cast copper alloy, chromium plated fancy type, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe, complete all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S&F in repairs CI Floor trap long neck 100 mm dia, with stainless steel grating including jointing to waste pipe fixed in cement concrete type B1, 1:2:4 complete all as specified and directed .

Dismantling of exisitng Chimney located at Cook House, complete all as specified and directed.

Chipping , removing carefullly concrete work by low impact hammer, breakar without damaging the structure & cleaning and disposal of debries out side the premises etc. complete all as specified and directed. NOTE: Hard concrete should not be removed by force.

Cleaning existing reinforcement with wire/ rotary wire brush, making the surfaces free from loose material dirt etc. complete and M&L for applying two coats of alkaline rust converting primer (Make: FEOVERT of Krishna Conchem or Roff rust cleaner of Piddilite or Dr. Fixit Rust removal or ShaliRust of STP Ltd. or equivalent as approved by GE) on the rebars, including cleaning the reinforcement, wirebrushing to remove loose rust spalls, wash the rebars with clean water within 3 min and wipe it dry complete all as specified and directed.

M&L for applying two coats of Epoxy based Zinc primer in a span of four hours over the treated rebars and allow to dry for six hours. The application shall be by brush complete all as specified and directed. Make: Corroseal-ZR of Krishna Conchem or Dr. Fixit Epoxy zinc primer or equivalent as approved by GE.

Cleaning all loose laitance on the concrete substrate and M&L for applying one coat of epoxy bonding agent on exposed concrete surface to ensure bond between old concrete & new concrete by brush application complete all as specified and directed. Make: MONOBOND SBR of Krishna Conchem or Dr. Fixit epoxy bonding agent or Shalicrete URP of STP Ltd. or equivalent as approved by GE.

M&L for Building up the profile of structural members by using latex additives (MONOBOND) modified air cured mortar system (Polymer modified mortar) (1:5:15 = 1 monobond-5 Cement-15 sand) -in damaged areas in 30mm thickness including leveling profliling etc complete all as specified and directed.

M&L for Drilling and fixing Rohibb Teflon nozzles in RCC members, including drilling holes of 12mm dia, 50 to 100mm deep holes complete all as specified and directed. Works shall be carried out as under :- (i) Cleaning of holes. Clean the holes by air blower prior to fixing nozzles. (ii) Fixing of nozzles. Insert 12mm dia. Rohibb Teflon nozzles in cleaned holes. External end of nozzles to be machine to receive outlet of grouting gun.Fix it inside the holes by applying thixotropic epoxy putty to ensure complete sealing. Cure the system for min.12 hrs. (iii) Cutting of nozzles. Cut the nozzles by chisel after completion of grouting without damaging structural elements. (iv) In case crack upto 2mm wide, fix the injection nozzels directly over the cracks, at intervals of 6 to 9 inches, using a drilling machine. Fix PVC/MS nozzels in these holes with fast-setting epoxy putty & let it dry for 2 to 3 days. Also, seal the crack between the ports with epoxy putty. (v) In case where the crack is wider than 2mm upto 4 to 5mm, drill holes at the sides of the crack in a staggered fashion, at intervals of 6 inches and affix them with epoxy putty as mentioned above. (vi) Also, seal the face of the crack with a liberal application of the epoxy putty.

M&L for Injecting of site mixed cement slurry grout, mixed in specified proportion containing cement, sand water with addition of plasticizers (approved make) & migratory corrosion inhibitors, water cement ratio shall be varied between 0.5 to 1.0 for each hole, shrinkage compensating cement slurry mixed to a lump free fresh creamy consistency, Mixing shall be done by mechanical mixer continuously stirring mechanically to keep cement particles in suspension. Injection of approved/specified grout by means of pump at a pressure of 3-5 Kg/cm2 etc complete till the grout mix flows out from the nozzle indicating complete filling of grout in the holes drilled complete all as specified and directed. Make: Dr. Fixit Epoxy injection or EPCO KP-HP-250 of M/s Krishna Conchem or Shaligrout EI of STP Ltd. or equivalent as approved by GE.

M&L for Injecting low viscosity (3-5cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories till nozzles refuses to accept the grout, Including,Mixing of materialas:Mixing of material components(part a&b) in the required quantities as per manufacturer's instruction by weigh batching.Grouting:Fill the grouting gun with concrete penetrating corrosion inhibitor (Make:EPCO-KP-100/Protectsil CIT or Ferogard 903 or equivalent as approved by GE). Maintain desired pressure in the gun by air compressor; maintain the pressure at exit (2 to 3kg/cm2) by monitoring pressure guage at exit.Grout the material through prefixed nozzles in the structural elements@ 100ml per nozzle. Repeat the process for all the nozzles complete all as specified and directed.

S&F in repairs TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. Note:-Replacement of steel reinforcement with TMT bars of appropriate size where 30% of cross section is reduced.

S&F in repairs 5mm dia and over upto and including 10mm dia additional main steel bar or stirrups of designed diameter in various structural elements like column ,beams and foundations including drilling, bending, welding and fixing the bars with epoxy putty etc.complete all as specified and directed. (Steel provided on the basis of 1% of volume of concrete). Note:-Replacement of steel reinforcement with TMT bars of appropriate size where 30% of cross section is reduced.

M&L for providing and applying jacketing around columns with Micro concrete M40 including all lifts, shuttering, drilling holes and fixing shear anchor as per specification complete all as specified and directed. Note:(i) Reinforcement shall be measured and paid separately.(ii) Rates including jacketing, formwork and micro concrete.

JOB (A) EM WORKS

Taking down carefully copper /aluminum point wiring ( light,fan,socket or power) complete, with wiring acessories such as bend boards Elbows only, ceiling fittings etc and removing material to store for safe coustody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

All as per BoQ Serial Item No.77.00 above but One fan/exhaust fan point controlled by one switch

All as per BoQ Serial Item No.77.00 above but One 5 pin socket outlet 5 Amps on same board

All as per BoQ Serial Item No.77.00 above but One 5 pin socket outlet 5 Amps on independent board

All as per BoQ Serial Item No.77.00 above but with 2.5 sqmm multi stranded copper conductor 1100 volts grade FRLSH PVC insulated sheathed cable with FRLSH PVC 2.5 Sqmm multi standard insulated unsheathed copper wire for continues earth on independent board.

S&F switch modular single pole one way, 6 Amp complete all as specified and directed.

S&F modular bell push flush type 6 Amp complete all as specified and directed.

S&F modular socket outlet 15 Amp, 5-in-1, controlled by one switch complete all as specified and directed.

S&F switch modular single pole one way,16 Amp complete all as specified and directed.

S&F modular socket 2 in 1, 3 pin, 6 Amp flush type complete all as specified and directed.

S&F modular fan 5 step regulator for ceiling fan complete all as specified and directed.

S&F modular ding dong door bell electric suitable for AC 230 volt, single pole complete all as specified and directed.

S&F modular ceiling rose, 3 phase/PVC/polycarbonate, isolated body, three terminals complete all as specified and directed.

S&F modular dummy type switch cover 1 module complete all as specified and directed.

S&F modular white cover plate with frame 1/2 module complete all as specified and directed.

S&F modular white cover plate with frame 3 module complete all as specified and directed.

S&F modular white cover plate with frame 4 module complete all as specified and directed.

S&F modular white cover plate with frame 6 module complete all as specified and directed.

S&F modular white cover plate with frame 8 module complete all as specified and directed.

S&F modular white cover plate with frame 12 module complete all as specified and directed.

S&F modular MODULAR METAL FLUSH BOX with frame 1/2 module complete all as specified and directed.

S&F modular MODULAR METAL FLUSH BOX 3 module complete all as specified and directed.

S&F modular MODULAR METAL FLUSH BOX 4 module complete all as specified and directed.

S&F modular MODULAR METAL FLUSH BOX 6 module complete all as specified and directed.

S&F Modular MODULAR METAL FLUSH BOX 8 module complete all as specified and directed.

S&F modular MODULAR METAL FLUSH BOX 12 module complete all as specified and directed.

S&F in repairs LED batten 20/22W LED tube light (4"), 220V, AC, 50Hz in wall/surface connecting with all required accessories like PVC box base, flexible cable from ceiling rose etc, surge protection, high power factor, Surface and wall mounted LED batten, Engineering plastic batten with accessories complete all as specified and directed.

S&F in repairs double door MCB DB made out of 18SWG CRCA steel sheets, Phosphates powder coated with copper bus bar, Earth stud, Din Rail, Polyamide Terminal Blocks for incoming and outgoing circuits, inbuilt loose wire box, Ground terminal blocks, duly pre-wired with thimble flame retardant copper conductors and poly layer for protection SP 240 volts 200 Amps rated bus bar 8 way double door open able complete all as specified and directed.

S&F in repairs MCB SP 240 V, 50 Hz, 10 KA conforming to IS 8828 of rating 5 to 32 Amp, 'C' series complete all as specified and directed.

S&F MCB double pole RCBO 240 volts AC 40 Amps (C-series) of 30mA complete all as specified and directed.

Fixing only exhaust fan and connecting up including provision of cable from ceiling rose/connector to fan and fixing louvers shutters from outside of the bldg, arrangement for fixing the louvers complete all as specified and directed.

S&F LED building security light fitting with suitable size bracket/angle to fit security light of 45w IP 66 protection LED complete all as specified and directed.

M&L for wiring for circuits/sub main wiring with FRLSH PVC insulate sheathed 2 x 4sqmm stranded copper conductor cable 1100 volts grade heavy duty drawn with & including concealed PVC conduit with 4 sqmm PVC insulated green copper cable for continues earth with suitable dia of PVC pipe with all accessories complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode size 600 x 600 x 6.0mm thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below ground level with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanised iron strip 32 x 6 mm dia by means of bolts, nuts, check nuts and washers of galvanised steel and GI pipe light grade 20mm dia bore for watering funnel with wire mesh. CI cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work in any type of soil all as shown in electrical plate No 3 connected to earthing test point including testing on completion complete all as specified and directed. Note : The unit rate includes for protection pipe and earth strip from top of earth plate up to 7.5 meter above ground level.

JOB (B) EM WORKS

Supplying, laying, jointing, connecting & testing 3.5 core 95 Sqmm XLPE/PVC insulated PVC sheathed cable heavy duty, 1100 volts grade, aluminum conductor as in trenches / ducts including taking out cable complete all as specified and directed.

Excavation in trenches for not exc 1.5 mtr wide and not exc 1.5 mtr depth and getting out in any type of soil including taking out faulty cable/cable covers and GI pipe complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layers n.exc 25cm complete all as specified & directed.

Removing excavated materials n.exc 50m and depositing where directed at a level n.exc 1.5m above the Starting point complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using (using 40mm graded stone aggregate) as in foundation of pole complete all as specified &directed.

M&L for PCC type B-1, 1:2:4 using (using 20mm graded stone aggregate) as in coping, including form work complete all as specified & directed.

M&L for dry river sand as sand cushioning for protection of UG cable including punning of sand in layers complete all as specified and directed. NOTE: Punned thickness shall be measured for payment purpose.

Supply & laying un-reinforced precast concret cable cover class LV type 1, flat size 250mm x 150mm x 40 mm complete all as specified and directed.

M&L for Cutting of Bituminious road / hard standing / PCC path / wall, including excavation in any type of soil, 25cm in width & 25cm in depth, and with & including filled with Plain cement concrete 1:2:4 type B-1 (using 20mm graded coarse aggregate) complete all as speified and directed.

M&L for GI pipe light grade with all fittings laid in trenches 80 mm bore of pipe complete all as specified and directed.

Please Enable Macros to View BoQ information