RASTRIYE RAJMARG-28 VARANSI TO KAKRAHAWA ROAD IN KM-109.00 TO BAHADURPUR VIKAS KHAND KO TWO LANE SE JODNE KA KARYA

Amount

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness. As per MORT& H Specifications Clause No. 201 complete in all respects as per directions of Engineer in Charge.

Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 As per MORT& H Specifications Clause No. 305 complete in all respects as per directions of Engineer in Charge.

Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m. As per MORT& H Specifications Clause No. 301 complete in all respects as per directions of Engineer in Charge.

Loosening of the ground upto a level of 500 mm below the sub-grade level, watered, graded and compacted in layers to meet requirement of table 300-2 for sub-grade construction. As per MORT& H Specifications Clause No. 305.3.4 complete in all respects as per directions of Engineer in Charge.

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density. As per MORT& H Specifications Clause No. 401 complete in all respects as per directions of Engineer in Charge.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. As per MORT& H Specifications Clause No. 414 complete in all respects as per directions of Engineer in Charge.

Providing, laying and suprending of graded stone aggregate (WMM) after mixing with water at OMC in mechanicl mix plan carring of mixed material by tipper to site, laying with 1% OPC cement and 3.5% Emulsion in uniform single layer on sub base/ subgrade and compacting with the road roller to achieve the desire denisity. As per MORT& H Specifications Clause No. 406 complete in all respects as per directions of Engineer in Charge.

Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction. As per MORT& H Specifications Clause No. 505 (B) complete in all respects as per directions of Engineer in Charge.

Providing and applying tack coat with bitumen using bitumen pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. As per MORT& H Specifications Clause No. 503 complete in all respects as per directions of Engineer in Charge.

Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction. As per MORT& H Specifications Clause No. 507 (B) complete in all respects as per directions of Engineer in Charge.

Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing As per MORT& H Specifications Clause No. 602 complete in all respects as per directions of Engineer in Charge.

Construction of U Type RCC drain. Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. As per MORT& H Specifications Clause No. 304 complete in all respects as per directions of Engineer in Charge.

Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days. As per MORT& H Specifications Clause No. 2100 complete in all respects as per directions of Engineer in Charge.

Plain/Reinforced cement concrete in sub-structure upto 5 m height, except for formwork which shall be 10 per cent instead of 4 per cent of cost of material, labour and machinery. As per MORT& H Specifications Clause No. 1500,1700 & 2200 complete in all respects as per directions of Engineer in Charge.

Supplying, fitting and placing HYSD bar reinforcement in super-structure complete As per MORT& H Specifications Clause No. 1600 complete in all respects as per directions of Engineer in Charge.

Widening of 900mm dia NP3 humepipe culvert Excavation of foundation in ordinary soil (Loam, Clay, or Sand) including 1.5 m lift and lead upto 30 m and including filling watering and ramming of excavated earth. Complete in all respects as per directions of Engineer in Charge. As per S.I. No. 251.

Providing and laying cement concrete in 1 : 4 : 8 with 40 mm nominal size brick aggregate.Complete in all respects as per directions of Engineer in Charge. As per S.I. No. 275

Class 150 Brick work in 1 : 3 Cement and coarse sand in sub and super structure.Complete in all respects as per directions of Engineer in Charge. As per S.I. No. 307.

Providing and laying of RCC NP - 3 hume pipe of 900 mm internal diameter in proper slope including fixing of collars with jute and cement. Complete in all respects as per directions of Engineer in Charge.

Pointing with 1 : 2 cement and fine sand mortar over brickwork in sub structure. Complete in all respects as per directions of Engineer in Charge. As per S.I. No. 574

Const. of R.C.C. Culvert 1x4.00 M R.C.C. Culvert Excavation of foundation inordinary soil as per S.I. No.- 251.

Concrete with 4.00 cm. gauge approved 40 mm. S/Ballast coarse sand and cement in the proportion of 1:3:6 as per S.I.No.- 280

Ist Class brick work in 1:4 with cement and approved Fine sand infoundation & Bed Level as per S.I. No. 307

Ist Class brick work in 1:3 with cement and approved Course sand infoundation Supter Structure as per S.I. No. 307+309

Brick on edge floor 1:6 & Pointed 1:2 over 8 cm. base cement concrete in 1:4:8

R.C.C. work with cement and approved coarse sand and 20 mm. gauge approved stone ballast, in the proportion of 1:1.5:3 as per S.I. No.284

Same as item-4 but in Slab S.I. No. 284

P.C.C. Work in 1:2:4 in Wearing Coat S.I. No. 282

M.S. or iron work in plain work such as reinforced cement concrete as per S.I. No.- 504

12 mm. thick plaster with cement and C sand mortor in 1:4 on parapet number plate as per S.I. No. 583A

Struck-Cement pointing with 1:2 cement and fine sand mortar as per S.I. No. 574

M/S RAJ CONSTRUCTION

RAHUL CONSTRUCTION

M/S JITENDRA SINGH

ASHTBHUJA CONSTRUCTION

M/s A K Construction Company