Construction of New Model Anganwadi Centre at Agatti (Nand Ghar)

Amount

Surface dressing of the ground including removing vegitation and in equalities not exceeding 15cm deep and disposal of rubbish lead up to 50 metres and lift up to 1.5 metres

Earth work excavation in foundation trenches or drains not exceeding 1.5m in width or 10 sq.m on plan including dressing of sides and ramming of bottoms, lift upto 1.5m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc layers not exceeding 20cm in depth consolidating each deposited layers by ramming and watering lead up to 50 mtr and lift up to 1.5 metres

Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material

Beyond 30 cm girth upto and including 60 cm girth

Beyond 60 cm girth upto and including 120 cm girth

Beyond 120 cm girth upto and including 240 cm girth

Providing and laying cement concrete 1:4:8 (1 cement 4 M. sand 8 graded stone aggregate 40mm nominal size) excluding the cost of centring and shuttering and reinforcement for foundation and plinth

Providing and laying cement concrete 1:5:10(1 cement 5 M. sand 10 graded stone aggregate 40mm nominal size) excluding the cost of centring and shuttering and reinforcement for foundation and plinth

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size ) for ramp

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3(1 cement, 1.50 M.sand, 3 granite chips 20mm nomnal size) a) Foundation and plinth

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sandes : 3 graded stone aggregate 20 mm nominal size ).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :

Providing and fixing precast cement concrete 1:1.5:3 ( 1 cement: 1.5 river sand: 3 graded stone aggregate 20mm nominal size) set in position with cement mortar 1:2 (1 cement :2 coarse sand) and finished smooth with 6mm thick cement plaster 1:3 (1 cement :3 fine sand) on exposed surfaces including centering and shuttering in -

Centring and shuttering including strutting, propping etc. and removal of form work

a) Foundations, footings, bases for columns

b) Lintel and Beam grider, Bressumers, Cantilever

c) Coloum ,piller ,Piers and abudtment

(d)Suspended floors, roofs, landings, balconies and access platform.

Providing plaster drip course/groove in plastered surface or modular to RCCC projection

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more, with provision for fusion bonded epoxy coating by mechanised and qualified process including cleaning the surface, heating by iduction heater,electrotatically sprayin the epoxy powder, complete fusion to give a coating thickness of 150 to 300 microns,gradual cooling without affecting the properties of steel, tesing as per IS13260/ASTMA775, flexinbility/bend tests etc and other test for ASTM standards.

Providing and laying factory made Precast concrete solid blocks of Size 40x20x15cm of grade M10 made of C&D waste from approved manufacturer in foundation and plinth in with CM 1:6 ( 1cement, 6 M sand )

Providing and laying factory made Precast concrete solid blocks of Size 40x20x15cm of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level with CM 1:6 ( 1cement, 6 M sand )

Providing and laying half block masonry with factory made Precast concrete solid blocks of Size 40x20x10cm of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level: with 1:4 ( 1cement, 4 M sand )

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). (9.1.1) Second class teak wood

Providing and fixing 30mm thick panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) 9.5.1 Second class teak wood

Providing and fixing panelling or panelling and galzing in panelled or panelled and glazed shutters for doors,wndows and celestory windows (Areaof opening for panel inserts excluding portion insidegrooves or rebates to be measured).Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 4mm thick Float glass pane

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing 40X3mm Iron hold ast 40cm long i/c fixing to frames with 10mm dia bolts, nuts and wooden plugs and embedding in cement concrete blocks of sizes 30x10x15cm of mix 1:3:6 ( 1 cement 3 M.sand 6 stone aggregate 20 mm nominal size)

Providing and fixing bright finished brass door latch with necessary screws etc. complete 300x16x5 mm

Providing and fixing bright finished brass casement stays (straight peg type) with necessary screws etc. complete 250 mm weighing not less than 280 gms

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete (a) 250x10 mm

Providing and fixing bright finished brass handles with screws etc. complete: (a) 125 mm

Providing and fixing nickel plated M.S pipe curtain rods with nickel plated brackets ; 20mm dia (Heavy type)

Providing and fixing Stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding,buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fastners, stainless steel bolts etc,. of required size on the top of the floor or the side of waist slab with suitable arrangements as per approval of Engineer-in- Charge(for payment purpose only weight of stainless steel members shall be considred excluding fixing accessoires such as nuts, bolts, fasteners etc.)

Stainless steel (grade-304) holllow section round/sqare tubes ( Stair Hand rail)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Glazed Vitrified tiles size of Tile 1200x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. (11.46.3) Size of Tile 1200x600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Providing and laying Ceramic glazed floor tiles of size 600x600 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ .3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying rectified Glazed Ceramic Wall tiles of size 1200x600 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey ement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble/Steel gray marble

Extra for providing edge moulding to 18mm thick tiles counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Marble work

6mm thick cement plaster to ceiling 1:3 (1 cement 3 M. sand)

12mm cement plaster 1:6 (1 cement 6 M. sand) Out side

15mm cement plaster 1:6 ( 1 cement 6 M. sand) on the rough side of single or half brick wall (Inside)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix 1:3 (1 cement: 3 M sand)

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litr (Birla/Nerolac or equivalent)

Providing and applying wall putty of 2mm thickness over plastered surface to prepere the surface even and smooth complete.(Birla/Nerolac or equivalent)

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two Coats (Birla/Nerolac or equivalent)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)(Birla/Nerolac or equivalent)

Painting wood work with Deluxe multi surface paint to give an even shade.Two or more coats applied on @0.90 ltr/ 10 sqm )over under coat of primer applied @ 0.75 ltr/10 sqm of approved and manufacture. (Nerolac or equivalent)

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

20mm Nominal bore

32 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

20 mm nominal bore

32 mm nominal bore

Providing and fixing CP brass bibcock of approved quality and manufacture complete.15mm nominal bore

Providing and Fixing C P Brass stopcock of approved quality and Manufacture complete. 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25mm nominal bore

Providing and placing on terrace (at floor level) polythene water storage syntex tank ISI :12701 marked,with cover and suitable locking arrangement and making necessary holes for inlet ,outlet and overflow pipe but without fittings and the base support for tank 1000lit. capacity

Providing and fixing nominal guage PVC Pipe of approved quality compleate with special flang compression type fittings including trenching and re filling etc. External work, a) 110mm nominal bore

b) 63mm nominal bore

Providing and fixing white vitrous China water closet Pedestal pan (European) type WC pans with white plastic seat and lid and rubber buffers, 15 white vitrous China low level flushing system of approved make with fittings and brackets 40mm flush bend, 20mm over flow pipe with complete including cutting and making good the walls and floors where required. White EWC with plastic seat and lid (Jaquar or Equivalent)(Model No. SLS- WHT-0311/ SLS-WHT-0318) or Model No.CNS.-wht-363SPPZ

Providing and fixing white vitrous China wash basin with RS or CI brackets painted white, 15mm C.P bras pillar tap and C.P brass chain and rubber plug 32mm C,P. brass waste of standrad pattern 32mm diametre and waste pipe complete including cutting and making good the walls and floors where required. (Jaquar or equivalent)

White vitreous China Flat back wash basin 550x400mm with one 15mm C.P. brass pillar tap., (Model No. FNS-WHT-0606, FNS-WHT-1503/ FLS-WHT-0606)

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :.(Jaquar or equivalent) Mirror size 700x500mm

Providing and fixing Health faucet (hand Shower) 15mm dia (Jaquar or equivalent)

Providing and fixing PTMT towel rail brackets fixed to wooden cleat with CP brass scerws with concealed ritting arrangement of approved quality and colour. 600 mm long towwel rail brackets with total length of 645mm, with 78 mm and effective height of 88 mm, weighing not less than 190gms.

Providing and fixing PTMT liquid soap container109mm wide,125mm high and 112 mm distance from wall of standared shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105gms.

Providing and fixing CP Brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 15 mm nominal bore

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets,gates and similar works

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing material and labour for painting Artistick work as approved by Engineer in charge with Synthetic Enamel paint of approved brand and manufacture of required colour on wall surface etc.complete

Wiring of light point/fan point exaust point/call bell point with 1.5 Sq.mm FR PVC insulated copper conducted single core cable in surface /recessed medium class PVC conduit /cassing capping with piano type switch ,phelonlic laminated sheet,suitable size MS bars,and earthing the point with 1.5 Sq.mm,FR PVC insulated copper conductor single core cable etc as required group A

Point wiring for looped PLUG with tissino type single pole ISI marked 6 A .Switch and 6 A Socket erected with necessary connections erected on polished wooden block/Metal/PVC Box covered with 3 mm thick lamination sheet for open /concealed wiring .

Wiring circuit /submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit as required 2X2.5 Sq.mm+1X2.5 Sq.mm earth wire

wiring for circuit/submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor,single core cable in surface/recessed medium class PVC conduit as required 2X4 Sq.mm earth wire

6 amps to 32 ampsratings,SP MCB,"C" curve ,10 KA breaking capacity

Providing and erecting ,Three pole MCB isolator AC 22 duty confirms to IS 13947.3 in existing box (a) for 40 Amp Cat.III

Providing and erecting ,sheet steel powder coated MCB distribution board.flush /surface mounted fitted with busbar,neutral link,earth bar and DIN rail ,confirming to IS 13032 and BS 5486:1986 without MCB to house approprire nos .of MCB's (The DBs sholud be used of same company of MCB to be used)(F) Single phase 8 way SS Double door

Earthing with copper earth plate 600 mm X600 mm X3 mm thick including accessories ,and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metere long etc with charcoal/coke and salt as required

Supplying of Onew Nos SP 16 A Switch & One No.6/16 A Univeral socket combined with indicator & Fuse

Providing & erected Approved make ceiling fan with double ball bearing ISI mark with condensor AC 230 V 50 c/s 1200 mm sweep complete ,canopy and 30 cms,Down rod erected on existing hook or clamp with 24/0.2,3 core flexible wire with earthing (make shall be approved by enginner in charge)

Providing and erectingfresh air fan 250 mm dia with square frame make of ABS body with louvers Cat.III

Providing and erecting Decorative Box type with plastic /polyester cove fluresent fitting with electronic Ballast finished with anti rust treaded white stove eanmelled with end paltes and holders with erection on site with lead wire and connection with 1 tube 40 watt 120 cms and adaptor if required

Supplying and erecting LED street light/flood light fittings with High power White LED,s wattage of 1 Watt and above assembled on single MCPCB,efficiency more than 130 m/w and corrosion free high pressure die cast aluminium housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and polycarbonate optics/lenses with company mark/name engrave or embosees 120 to 300 V power Factor morethan0.95,THD<10% CCT 5000 K uniformity ration >0.45,Luminaire efficiency >85 CREE/OSRAM/Philips Lumileds /NICHIA/ SEOUL/ Bridge Lux (USA) make LED used for luminaire (Each fittings requred LM 79 M& LM 80 certificates) (A) Street light (IP-65).Surge-4KV(e) above 48 to 60Watt

MOHAMMED NAVAB SHAH C G

FATHAHULLA C P