CERTAIN SPECIAL REPAIR AND LBW WORKS AT SUNJUWAN UNDER GE JAMMU

Amount

B/R Portion: - Surface excavation n. exc. (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5m in depth and getting out in any type of soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm in soft / loose soil complete all as specified and as directed.

Removing excavated material outside of MOD land and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Material and labour for PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

Material and labour for RCC M-25 Design mix (using 20 mm graded crushed stone aggregate) as in column footing including raft footings, foundation, plinth beam, bases of columns etc. complete all as specified and as directed.

Material and labour for RCC M-25 Design mix (using 20 mm graded crushed stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and as directed.

Material and labour for RCC M-25 Design mix (using 20 mm graded crushed stone aggregate) as in columns, pillars etc complete all as specified and as directed.

Material and labour for RCC M-25 Design mix (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, manhole cover and in shelves and the like complete all as specified and directed.

Use and waste form work to sides of concrete foundation, footing, bases of columns, plinth beam, side and soffits of plinth beam and similar works in vertical or to batter of rough finished surfaces complete all as specified and as directed.

Use and waste form work Square, rectangular or polygonal to sides of columns, pillars etc. of rough finished surfaces complete all as specified and as directed.

Use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick, rough finished surface of concrete complete all as specified and as directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20 cm for rough finished surface complete all as specified and directed.

Use and waste form work to sides and soffits of floor or roof beams, lintel, cantilevers, shelves etc including support of rough finished surfaces complete all as specified and as directed.

Material and labour for steel reinforcement TMT bars 10 mm dia and over cut to length, bent to shape and tying with annealed MS wire 0.9mm dia all as specified and directed.

Material and labour for TMT bars 6 to 8 mm dia and over cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Material and labour brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete all as specified and as directed.

Material and labour half brick thick brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in CM (1:4) complete all as specified and as directed.

Material and labour 15 mm thick rendering in cement mortar 1:6 on brick work or concrete surface of wall finished even and fair complete all as specified and as directed.

Material and labour 15 mm thick rendering in cement mortar 1:4 on brick work or concrete surface finishing the surfaces even and smooth without using extra cement using water proofing compound as per manufacturer's instruction complete all as specified and as directed. Note: - Integral Water proofing compound shall be measured and paid separately.

Material and labour rendering 05 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces finishing surfaces even and smooth without using extra cement as in ceiling complete all as specified and as directed.

Material and labour for two coats of oil bound distemper of wall to newly plastered surfaces including preparation of surfaces with alkali resistant primer complete all as specified and directed.

Material and labour applying two coats of cement based paint over one coat of cement primer on newly plastered surfaces of wall including preparation of surface complete all as specified and as directed.

Material and labour for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash including preparation of newly plastered surfaces complete all as specified and as directed.

Material and labour 10 mm thick plaster in one layer in CM (1:3) over concrete roof padding, cement mortar mixed with and including chemical compound PIDIPROOF LW of DR FIXIT of PIDILITE INDUSTRIES LTD mixed in proportion 200 ml per 50 Kg cement or STP No. 1 (Liquid) of STP Ltd. in proportion 200 ml per 50 Kg cement as per manufacturer's instructions laid when concrete is still green and finishing the surface fair and even without using extra cement complete all as specified and as directed. Note: - Liquid water proofing compound shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and as directed. Make:- SUPER LATEX or DR. FIXIT of PIDILITE INDUSTRIES LTD and PIDIPROOF LW of DR FIXIT of PIDILITE INDUSTRIES LTD or equivalent make as approved by GE.

Material and labour Moorum / Red Bajri / approved earth filling in floors or pavings, laid in layers not exceeding 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

Material and labour broken stone hard core of gauge not exceeding 63mm deposited, spread and levelled in layers not exceeding 15cm thick, watered and rolled / rammed to a true surface complete all as specified and as directed.

Material and labour PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) 100 mm thick in sub base complete all as specified and as directed.

Supply and fixing pressed steel frames (factory made) made of size 1.25mm thick MS steel for door with one or more rebates including lugs, hinges, hold fast, lock strike plate etc complete of size 125 x 60mm including one shop coat of red oxide primer, PCC (1:3:6) as in back fill to chowkats complete all as specified and as directed.

Supply and fixing PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

Supply and fixing 35mm thick 2nd class hard wood plain framed panelled factory made shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces fitted to chowkhats complete all as specified and as directed.

Supply and fixing 35mm thick second class hardwood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part - I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR Part – II 2004 and as directed by GE / Engineer-in-Charge. Make: - “SYNTEX / RAJSHREE Plastic wood Forex, Indore”.

Supply and fixing 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and as directed.

Supply and fixing extruded aluminium alloy handles 150mm long 'D' type anodised complete ISI Marked complete all as specified and directed.

Supply and fixing Aluminium, anodised, barrel tower bolts of extruded section and fixed 200 mm long complete all as specified and as directed.

Supply and fixing 300mm long aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing with nut and bolt of ISI Marked complete all as specified and directed.

Supply and fixing mild steel helical / ordinary rat tail rod pattern door spring 300 mm including roller and roller plate complete fixed with welding (ISI Marked) complete all as specified and as directed.

Supply and fixing small fittings Ist class hardwood such as brackets of any types latch and hinge blocks shaped door and window stops and the like, not exceeding 200 cu.cm each complete all as specified and as directed.

Material and labour applying two coats of synthetic enamel paint on new or previously untreated wood and wood based surface over a coat of pink primer including preparation complete all as specified and directed.

Supply and fixing box type steel windows / ventilators comprised of tubular frame and shutters made out of 1.25 mm thick MS sheet tube factory made with double side shutters wire gauged shutter and glass glazed shutter (wire cloth and glass panes will be measured and paid separately) with side hung shutters with MS handles and MS peg stay dovetailed or welded including 02 No's MS Tower bolts 150 mm long for each leaf and 08 mm square bar grill / guard bars at spacing as shown on Drawing welded MS flat iron frame work, including other fittings, hinges, MS handles, tarred hold fasts, PCC blocks for hold fasts etc all as shown on Drawing No CEPZ/TD -354/09 sheet 1/3 to 3/3 including one coat of of red oxide zinc primer complete all as specified and as directed.

Supply and fixing sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane 3mm thick complete all as specified and as directed.

Supply and fixing figured glass, frosted head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane 3mm thick complete all as specified and as directed.

Supply and fixing Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.00mm fixed with tinned tacks, or galvanised wire staples all as specified and as directed.

Material and labour preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Supply and fixing curtain rod aluminium anodised 20 mm dia including brackets complete all as specified and as directed.

Material and labour PCC (1:3:6) type C-2, 75 mm thick laid as in plinth protection / paving etc finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for cement concrete (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) as in bed block, hold fast, coping, benching complete all as specified and as directed.

Material and labour water proofing treatment to RCC roof slab including parapet as under: - (a) Applying bituminous primer @ 0.30 ltrs / Sqm over cleaned and dry roof surface including parapet. (b) Laying one layer of APP based polymeric membrane, 3mm thick, weight not less than 3.60 Kg / Sqm, reinforced with non woven polyster fibre reinforcement (weight not less than 150 gm/Sqm), sealed by torch application with a minimum overlap of 100mm and 75mm at end and side of polymeric membrane. (c) A layer of hot blown bitumen grade 85/25 @ 1.20 Kg / Sqm and a layer of bituminuous aluminium paint as final finish @ 0.20 Kg / Sqm shall be applied on top surfaces of APP membrane. APP based membrane shall be “Super thermoley” manufactured by M/s STP Ltd or “Moply FP” manufactured by M/s Texsa India Ltd or equivalent of M/s IWL (I) Ltd.

Material and labour non skid ceramic colour joint free tiles 7 to 8 mm thick (Square / Rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Material and labour glazed ceramic colour tiles size 450 mm x 300 mm x 7-8 mm thick joint free on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

Supply and fixing Vitreous china, white, Squatting pan, 'Orissa' pattern size 580 x 440mm with integral foot rests water closet), front or back inlet complete, connection to drain pipe and to flushing pipe, anti-syphonage pipe etc complete including making good to floor to match with the existing complete all as specified and as directed.

Supply and fixing PVC (SWR) 'P' trap 110 / 110 mm bore complete all as specified and as directed.

Supply and fixing 10 litre capacity low level flushing cistern, with inlet float valve, moulded from virgin poly propylene slimline single flush including provision of 32 mm dia PVC flush pipe and making connections, ISI marked complete all as specified and as directed.

Supply and fixing PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore complete all as specified and as directed.

Supply and fixing pillar tap 15 mm dia cast copper alloy fancy type with capstan heads chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe fixed complete all as specified and as directed.

Supply and fixing vitreous china wash hand basin white, flat back of size 450mm x 300mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling including fixing of tap, waste fitting 32mm dia PVC waste pipe etc complete all as specified and as directed.

Supply and fixing bib tap cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified and as directed.

Supply and fixing stop valve / angle valve fancy type chromium plated screwed down, high pressure with capstan head suitable for 15 mm bore, screwed both ends for iron pipe complete all as specified and as directed.

Supply and fixing brass chromium plated shower rose 125 mm size swivel type with connecting rod 15 mm bore complete all as specified and as directed.

Supply and fixing stop valve cast copper chromium plated concealed type screwed down, high pressure with capstan head suitable for 15 mm bore complete all as specified and as directed.

Supply and fixing stainless steel gratings of outer frame dia 150 mm openable type including all necessary fittings such as hinges including embedding in tiles with white cement complete all as specified and as directed.

Supply and fixing PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps complete all as specified and directed.

Supply and fixing PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps all as specified and directed.

Supply and fixing PVC SWR bends of 110 mm bore complete all as specified and as directed.

Supply and fixing PVC SWR bends of 75 mm bore complete all as specified and as directed.

Supply and fixing PVC (SWR) junction double equal or unequal provided with access door of 110 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) junction single (single T) equal or unequal provided with access door of 75 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) reducer of 110 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) vent cowl 75 mm bore complete all as specified and as directed.

Supply and fixing PVC (SWR) WC connector with lip ring 110 mm complete all as specified and as directed.

Supply and fixing towel tail 20mm dia 'D' type 60cm long chromium plated brass screws and wooden / plastic cleats complete all as specified and directed.

Supply and fixing soap dish fixed with and including chromium plated brass screws and wooden / plastic cleats complete all as specified and directed.

Supplying, fixing, jointing and testing galvanised steel water tubing medium grade with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors, complete for 15mm dia bore complete all as specified and as directed.

Supplying, fixing, jointing and testing galvanised steel water tubing medium grade with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors, complete for 25mm dia bore complete all as specified and as directed.

Supply and fixing rotational moulded polyethlene water storage tanks of capacity 1000 litres, (cylindrical vertical with closed top) hoisted and fixed in position including necessary checknuts and washer and 20 mm dia PTMT ball valve complete all as specified and directed.

Mild steel bed side lookers size 760 x 600 x 1000mm embedded lockers foot in floor including partitions and racks, two coats of synthetic enamel paint over a coat of red oxide primer using mechanical spray complete all as specified and all as directed by Engineer-in-Charge.

Material and labour for 15mm thick screed bed or bedding layer for laying floor finishes in CM 1:6 complete all as specified and as directed.

Material and labour for chequered cement concrete tiles 20cm x 20cm x 25mm / 30cm x 30cm x 25mm thick, pre-polished set, jointed and pointed in neat cement slurry with grey / colour cement and pigment in floors complete all as specified and as directed.

Supply and fixing precast PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) kerb stone of size 300 mm x 125 mm and 300 mm height, chamfered at one end (75 mm x 75 mm) fixed vertically and set in CM 1:4 complete all as specified and as directed.

Septic tank for 10 users, single chamber (Brick construction) with top of slab at ground level including necessary excavation and earth work in any type of soil and disposal of surplus soil to a distance not exceeding 50 metres, vent pipe, supplying and fixing manhole covers with angle iron welded frame complete all as specified and as directed and shown in Drawing No CE/TD-1202/03 dated 09 Oct 2003 revised on 21 Oct 2003 Sheet 1/2 and CE/TD-1202/03 dated 09 Oct 2003 Sheet 2/2.

Soakage well 2.4 metre dia and 3.00 metre deep below inlet pipe level (depth from inlet pipe to ground level 45 cm) including excavation and earth work in any type of soil filled with brick bats, RCC slab with RCC manhole cover fixed in angle iron frame, SWG single junction inlet, filling around slab in slopes and disposal of surplus soil to a distance exceeding not exceeding 50m complete all as specified and as directed and shown in Drawing No CE/TD-1202/03 dated 09 Oct 2003 revised on 21 Oct 2003 Sheet 1/2 and CE/TD-1202/03 dated 09 Oct 2003 Sheet 2/2 all as specified and directed by Engineer-in-Charge.

Material and labour cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) concrete bed to drain pipes 150 mm dia including packing under and haunching against the sides of pipes after they are laid and tested in complete all as specified and as directed.

Material and labour salt glazed stoneware drain pipes of bore 150 mm dia grade 'A' laid in trenches, in concrete bedding and jointed complete in CM 1:1 all as specified and directed.

Material and labour cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in benching, coping complete all as specified and as directed.

Material and labour precast RCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in manhole cover including necessary formwork except slab set in CM 1:4 complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish (without any extra cost to Govt) and removing from site complete all as specified and directed by Engineer-in-Charge.

Taking down shutters exceeing 1 Sqm and not exceeding 2 Sqm and refixing in the same opening complete all as specified and as directed.

Demolition of brickwork or stone / boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc all as specified and as directed and removing unserviceable material outside cantt area.

Taking down GI tubing of 15 mm dia and connections including cleaning for refixing or removal complete all as specified and as directed.

Supply and fixing 15 mm dia galvanized pipes 'medium grade' with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and as directed.

Material and labour including preparation and applying two coats of white wash on ceiling including preparation of old plastered surfaces complete all as specified and as directed.

Material and labour applying two coats of synthetic enamel paint on existing wooden surface including preparation of old surface of any description over 10 cm width or girth complete all as specified and as directed.

Supply and fixing in repairs Vitreous china wash hand basin white, oval shape of size 580 x 400mm with PVC connection (15 x 450) mm long with PTMT nuts and PVC washer and including cutting for pinning in ends brackets and provision of GI waste pipe 32mm (Light grade) of adequate size and length, brass chromium plated waste coupling 32 mm dia, cast copper alloy chromium plated angle valve 15 mm dia bore, 15mm dia CP pillar tap fixing and taking down unserviceable wash hand basin complete all as specified and as directed.

Supply and fixing in repairs vitreous china wash down water closet pan (EWC / long pan / pedestal pattern) white in colour including seat cover, closed pattern, flat bottom, and mild steel chromium plated hinging device complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair vitreous china urinals, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement with grating and union for discharge pipe, including PVC waste pipe 32mm of suitable length, PTMT waste coupling 32mm dia suitable for urinals, PVC connection 15 x 450mm long, CP urinal spreader, 15 mm angle valve fancy type chromium plated complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

Taking down chowkats or frames with shutter without taking off shutter from the frame exceeding 1.5 sqm and not exceeding 4 Sqm each and removing from site complete all as specified and as directed.

Supply and fixing aluminium door shutter (Double or single leaf) with frame made out of aluminium section of size 83 x 44 x 1.5mm in frame, Style, top and bottom rail using section 114 x 44 x 1.5mm including 5 mm thick float glass panes of modi fixed with heavy duty aluminium clips at top panel neoprin rubber gasket, angle cleats etc complete with heavy duty floor door closer, aluminium handle approved shape 2 No's, aluminium tower bolt 200mm size 01 No's, 4 lever lock of approved manufacturer, complete with cost of all materials, labour, T&P, wastage, including making good existing surface disturbed during taking of old chowkat etc, sections size vary as per availability but weight should not be less than 1.3 kg / RM for frames and styles including powder coating of approved colour (Thickness of powder coating not less than 50 micron) complete all as specified and directed.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections / appropriate 'Z' sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, CP brass / stainless steel screws, complete as per architectural drawings and the directions of Engineer-in-Charge.

Supply and fixing in repair 5.5 mm thick Sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 Sqm in each pane complete all as specified and directed.

Supply and fixing 12 mm prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations fixed with screws to timber frame work complete all as specified and directed.

Supply and fixing solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed.

Supply and fixing aluminium anodised diamond shape grill of size 75 x 75 x 10 mm thick (DG-910) complete all as specified and directed.

Supply and fixing in repair sheet glass shelf assembly consisting of guard rails and bracket 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long with Aluminium alloy complete all as specified and directed.

Supply and fixing in repair tubular towel rail, 20mm dia, 'D' type and 60cm long between flanges of brass chromium plated complete all as specified and directed.

Supply and fixing in repair CP grating doom 100mm dia including embedding in tiles with white cement complete all as specified and as directed. (Minimum weight 25 gms).

Supply and fixing in repair Jet spray with 1.00 m tube complete all as specified and directed.

Supply and fixing in repair CP brass health faucet with 1.0mtr tube and hook (braded tube) complete all as specified and directed.

Supply and fixing in repair Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws box type complete all as specified and directed.

Dismantling water tanks and removing to store complete all as specified and directed.

E/M Portion: - Material and labour for one point wiring with FRLS insulated cable with stranded copper conductor cable 1.5 Sq mm size single core, including one No. 1.5 Sq mm single core FRLS insulated copper cable as for continuous earth wire drawn in and including PVC conduit 20 mm dia, including cutting chases for concealed conduit wiring etc terminated into GI pressed sunken box including 3.0 mm thick hylum sheet cover for mounting switches, socket, fan regulators etc. and making good, cutting not exceeding 10 cm girth complete for one light / ceiling / exhaust fan point controlled by one 5 Amp switch one way complete all as specified and directed.

Description all as per Ser item No. 117.00 here-in-before but for one 3/5 Pin, 5 Amp socket outlet on independent board complete all as specified and directed.

Description all as per Ser item No. 117.00 here-in-before but for one 3/5 Pin, 5 Amp socket outlet on same board complete all as specified and directed.

Material and labour for one point wiring with FRLS, PVC unsheathed and PVC insulated cable, with stranded copper conductor cable 2.5 Sqmm size single core, including one No. 1.5 Sqmm single core FRLS, PVC insulated copper cable as for continuous earth wire drawn in and including PVC conduit 20 mm dia, including cutting chases for concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth complete for one 6 Pin, 15 Amp socket outlet on the independent board including GI sunken box and hylum sheet complete all as specified and directed.

Supply and fix switch piano flush button single pole one way 5 Amp, 240 volt complete all as specified and directed.

Material and labour for switch 15 Amp flush type, 240 volts, complete all as specified and directed.

Material and labour for socket outlet 3 Pin, 5 Amp flush type, 240 volts, complete all as specified and directed.

Material and labour for socket 2 in 1, 3 pin, 5 and 15 Amp flush type universal, 240 volts, complete all as specified and directed.

Material and labour for ceiling rose, surface bakelite, three terminals 240 volts complete all as specified and as directed.

Material and labour for lamp holder, insulated body, threaded dome pattern, suitable for bracket fittings including LED bulb 9 watt complete all as specified and directed.

Supplying and fixing indoor decorative aluminium extruded T5 LED batten including LED tube rod of capacity 18 watt, 4' (feet) integrated type including connections with 2 core flexible copper wire 0.50 Sqmm from ceiling rose light fittings fitted on PVC round / square box complete all as specified and as directed.

Supplying and fixing mini mirror LED light fitting 1 x 11 Watt complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing LED street light of capacity 1 x 25 watt Aluminium PDC housing, toughened glass cover with IP-65 protection in GI pipe bracket with suitable size medium grade complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep minimum air delivery 210 CFM with service value 6.00 BEE Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fixing DB with sheet metal enclouser 240 volts, double door 8 way with 200 Amp rated bus bar single pole and neutral for double door MCB including cutting chases for DB of required size and making good distrubed surface area complete all as specified and as directed.

Supply and fixing MCB single pole and neutral 240 volts of capacity 40 Amp complete all as specified and directed.

Supply and fixing MCB single pole of capacity 06 to 32 Amp, 240 volts complete all as specified and directed.

Material and labour for exhaust fan of sweep size 300 mm totally enclosed heavy duty motor, with die cast aluminium rotor mounted on 2 ball bearings, single pahse, 4 pole polarity, 1400 RPM, (metal body) complete all as specified and as directed by Engineer-in-Charge.

Supply and installed water heater storage type (Geyser) star rating complete, capacity 50 Ltrs including grouting of bolt for fixing of geysers complete all as specified and directed.

Supply and installed Desert cooler electric driven, single phase, including submersible pump of suitable capacity, fan motor 90 Watt, 2800 RPM, thickness of sheet steel body 1.2mm, having nominal air flow capacity of 4000 Cu.M / Hrs complete all as specified and directed.

Fabrication and installation of angle iron frame stand of suitable size as per site requirement for desert cooler made out from angle iron 40 x 40 x 6 mm thick duly mounted in brick / stone / masonery wall including iron clamp / nut and bolt complete with black painted two coats over a coat of red oxide primer all as specified and directed by the Engineer-in-Charge.

Material and labour Earthing with galvanized iron earth plate electrode 600 X 600 X 6mm size buried directly in ground vertically at a depth not less than 2.25 metre below ground level with the top edge of earth plate at a depth not less than 1.50 metre below ground level connected to GI wire 4.0 mm dia as earth lead by means of bolts, nuts, check nuts and washers of galvanized iron earth plate electrode surrounded by a packed thickness of charcoal or choke dust mixed with common salt in alternate layers not exceeding 150mm thick, GI wire protected with and including galvanized iron pipe 20mm bore (dia) light grade, upto 1.0 metre above the floor level of the building where main switch / DB situated including PCC pit in cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) and RCC cover of size 540 x 540 x 50mm in RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) reinforced with and including 8.0mm dia TMT bars @ 1OOmm centre to centre both ways and galvanized iron wire mesh, funnel, galvanized iron watering pipe 20mm bore (dia) medium grade, necessary excavation in soft / loose soil, returning, filling in and removal of surplus soil upto a distance not exceeding 50mtr and all as shown in electrical plate No. 3 of MES Schedule Part-I and testing on completion including taking down unserviceable earthing complete all as specified and as directed.

Cutting / Screwing existing CI / GI tubing for alteration or addition of 25 mm dia pipe in position without taking down complete all as specified and directed.

Supply and laying galvanised mild steel tubing medium grade 25mm bore with all fittings, laid in trenches, in floor / under road on wall complete all as specified and directed.

Supply and fix Gun metal globe or gate valves (ISI marked), with iron wheel head, screwed both ends for iron pipe or for unions for 25mm dia bore pipe complete all as specified and directed.

Material and labour for LT underground cable XLPE insulated, heavy duty armoured sheathed 1100 volts grade 16 Sq mm, 2 core, with aluminium conductor, ISI marked as per IS : 7098 (Part-1) complete all as specified and directed.

Supply and laying in trenches clear sand for cushioning under cable 8 cm below and 15 cm above complete in level all as specified and directed by Engineer-in-Charge.

Material and labour sub class 'B' bricks well burnt perpendicular to the axis for the cable in trenches for protection to cable complete all as specified and directed.

Supply and fixing stepped type electronic fan regulator flush type complete all as specified and directed by Engineer-in-Charge.

NOTE NO 1: - Samples of materials as approved will be kept in GE's sample room. NOTE NO 2: - All fittings and fixtures mentioned above will be fixed to the satisfaction of Engr-in-Charge and GE. NOTE NO 3: - Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings.

M/s Mohammad Shafi Malik

M/S PRITHIVI RAJ AND SONS

M/S LANGER CONSTRUCTION COMPANY

M/S BALWAN SINGH

M/S ARUN ANAND

M/S PARAMJEET SINGH

Bidder Name

M/S TRIKUTA BUILDERS

M/S ARUN ANAND

M/S PARAMJEET SINGH

M/s Mohammad Shafi Malik

M/S PRITHIVI RAJ AND SONS

M/S BALWAN SINGH

M/S LANGER CONSTRUCTION COMPANY