SPECIAL REPAIRS TO BLDG No. P-05 (COOK HOUSE) OF ASC AND SPECIAL REPAIR TO BLDG No.T-2, T-3, AND T-4 (OR LIVING LINE) OF SUPPLY DEPOT. AT NASIRABAD

Amount

Taking down cement or cement lime plaster on stone/brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M& L for 15mm thick rendering in cement mortar (1:6) on stone masonary surfaces finished, even and smooth without using extra cement, complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 on stone masonry external surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rough cast plaster with mixture of crushed or fine gravel aggregate (6 to 10 mm) mixed with coarse sand and cement in the ratio of 1:1:1 over and including 15mm thick under coat of cement and sand mortar 1:4 while it is still in plastic state, complete all as specified & directed by Engr-in-Charge.

M&L for 10mm thick rendering in cement mortar (1:4) on ceiling surfaces finished even and smooth without using extra cement, complete all as specified & directed.

Dubbing out average 10mm thick in CM 1:4 on irregular faces of walls or concrete chajjas etc complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over and including a coat of white wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed

M & L for preparation of new decorated surfaces of walls and providing two coat of cement base paint complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20-25mm thick over and including 15mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the smooth of the slab incl rubbing & polishing complete all as specified & directed.

M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for factory made 60mm thick machine pressed precast cement concrete coloured, reflective type interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M&L for PCC 1:2:4 type B-1 (using 20mm stone crushed agg.) as in rounded or chamfered on edges in any description complete all as specified.

Supply only water proofing compound ISI Marked.

M&L for glazed ceramic coloured tiles, size 450 mm X 300 mm, 6-7 mm thick on vertical surfaces of wall such as dados, skirting etc set & jointed in neat slurry and pointed in white or colour cement to match over and including 10 mm thick screed plaster in CM 1:4 complete all as specified and directed

M & L for non-skid ceramic tiles 7 to 8 mm thick ( square /rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured in white or coloured cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and directed.

All as per the above item No. 19.00 above but as in skirting over and including 10 mm screed plaster in CM 1:4 complete all as specified & directed.

M&L for 25mm thick PCC 1:2:4 type B-1 (using 20 mm thick crushed stone aggregate) as in sub base complete all as specified and directed.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion ordered and directed.

M&L for walling of random rubble, brought upto courses, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:6 complete all as specified & as directed.

All as per item No. 23.00 above but except stone.

M&L for brick work with fly ash bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc 20mm as specified.

Demolition of Stone slabs & tiles of any description or thickness in floors , aprons etc, complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

Taking out old unserviceable water closet (squatt pattern) and S & F Vitreous China, Squatting pan Orissa pattern size 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) with Vitreous China ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe , including PCC (1:2:4) type B-1 for fixing of WC and making good the floor to match the existing complete all as specified and directed.

Taking down old unserviceable flushing cistern S&F PVC valveless syphonic action type low level flushing cistern, 10 Ltrs capacity, white, with inlet ball valve, float, handle with 32mm PVC flush pipe, fixed on walls by driling holes and using PVC rawl plug of suitable size complete all as specified and directed.

Taking down old unserviceable PVC connection and S & F PVC connection, heavy duty 15 mm bore, 45 cm long with two Nos PTMT nuts at both ends of approved quality complete all as specified and directed

S&F in repair Soap dish any type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as specified & directed.

S&F in repairs tubular towel rail, aluminium anodized, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified.

S&F in repairs chromium plated Angle stop cock 15 mm dia screwed down light pressure screwed both ends for iron pipe or for union complete all as spd & directed

S&F in repairs Chromium plated bib taps, with capstan heads, screwed down for iron pipe or for brass ferrule & fixed for 15 mm bore pipe complete all as specified & directed.

S & F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to rigid UPVC waste pipe bent to shape & fixed to wall with bracket overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engineer-in-Charge

Taking down old wooden plate rack and S&F stainless steel plate rack made of 0.50mm thick of over all size 920mm x 785 mm x 255 mm and weight not less than 7.00 Kg each of approved quality complete all as specified and directed.

Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

All as per srl item above No. 39.00 above but 20 mm bore

All as per srl item above No. 39.00 above but 25 mm bore

S & F water tubing 15 mm bore, medium grade, ISI marked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed.

All as per srl item above No. 42.00 above but 20 mm bore

All as per srl item above No. 42.00 above but 25 mm bore

Fixing only 15mm bore old GI tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, Tee, union, socket, reducer etc complete all as specified and directed.

All as per srl item above No. 45.00 above but 20 mm bore

All as per srl item above No. 45.00 above but 25 mm bore

S&F in repairs CI Nahani/Floor trap 75 mm outlet with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4), complete, all as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site and making good disturbed surface of walls in cement mortar (1:3), complete, all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site and making good disturbed surfaces of wall in CM (1:3), complete, all as specified and directed.

M & L for rolled mild steel work angle iron as in door frame (Chowkhats) & cooler stand including provn of 12mm dia deformed bar welded horizontally to bottom of frame confirming to Fe-290 or Fe-330 including preparing back of chowkhat and applying two coats of tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed.

S & F factory made solid pannel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawings on page 176 to 181 of SSR Part - II 2020 complete all as specified and directed.

S & F second class HW Hollock/Bonsum/Sal 35mm thick, factory made, plain framed, paneled shutter with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as per specified and directed.

S & F for 2nd class HW 35 mm thick, gauged and skeleton shutters , factory made open rebated and prepare to receive glass, gauge etc (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. Size of members of shutter shall be as specified in SSR 2009 Part-I, section 8 clause Member shall be kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as specified and directed.

S & F Steel window/ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note: Wire mesh and sheet glass shall be measured & paid separately under respective items.

M&L for 18/19mm thick block board grade-.II quality, interior grade with decorative type with decorative face veneer on one face fixed complete, including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works all as spepcified and directed.

M & L for 20 to 25 mm thick machine cut kota stone Shelves incl pre rubbing & polishing and set in CM (1:4) incl cutting inserting into wall not less than 50mm deep and making good to disturbed surfaces complete all as specified and directed.

S & F continuous (piano) hinges, mild steel, bright finish width of flaps (when open ) 40 mm all as specified and directed.

M&L for IInd class H/W Plain , Solid , Straight chowkats and frames sec area n exe 40 sqcm complete and all as specified..

S & F 100mm size hasp and staple, aluminium anodised safety type, fixed with screws complete all as specified and directed

S & F 300mm long aluminium alloy,anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S & F extruded aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S & F 125mm single action spring hinges,mild steel with steel wire spring, stove enaelled black, complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as spd & directed.

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed.

S&F 3.00 mm thick sheet glass, ordinary / figured quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as spd & directed.

S&F in repair fancy type 20mm dia aluminium curtain rods powder coated fixed to bracket completed all as spd & directed.

S&F decorative type knobs with bracket of MS powder coated fixing at end of pelmet rod complete al as spd & directed.

Dismantling of existing unserviceable water tank of any description capacity exc 500 Ltr but n.exc 1000trs capacity each complete all as specified and directed

S&F 1000 Litre capacity rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top), hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F ball valves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore compete (Minimum weight 210 gm) complete all as spd & directed.

S&F in repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 25 mm dia, ISI marked complete all as spd & directed.

Taking down existing unservicable treatment of any description including cement plaster/conctrete any thickness from roof surface cleaning of roof surfaces and and preparing it for further treatment and removing rubbish from the site up to 50 mtrs complete all as specified and directed.

M&L for screeding 10mm thick in CM 1:4 on fair faces of RCC /stone patti roof surface finished fair & even without using extra cement even complete all as spescified and directed.

M & L for five layered roof treatment with APP modified polymeric water proofing membrane, 2mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 2.6 Kg/ Sqm applied with bonding material using belown type bitumen conforming to IS-702 Grade 85/25 @ 1.20 Kg/ Sqm over bitumen primer conforming to IS- 3384 @ 0.40 Kg/ Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg/ Sqm over APP membrane with all overlaps complete all as specified and directed.

M&L for 40mm thick (average consolidated thickness) PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion complete all as specified and directed.

M&L for coved fillet in PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate at junction of roof & parapet wall and other vertical surfaces and surface painted with a hot paving bitumen grade 30/40 conforming to IS-73 @0.70 Kg/Sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr Sqm complete all as specified and directed

M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in surface channel and drain etc complete all as specified.

Taking down CI pipe 100/75 mm fixed wall and floor etc including accessories complete all as specified and directed.

S&F CI soil and waste pipe 100mm bore waste or vent pipe in any length with or without ears, with cement joints on vertical surfaces of wall complete all as specified and directed.

Fixing only 100 mm bore CI pipe as on wall/trench/floor

S& F 100 mm CI soil waste and vent pipes single socketed in any length with cement joints laid in floor or in trenches complete all as specified and directed

S& F 75 mm CI soil waste and vent pipes single socketed in any length with cement joints laid in floor or in trenches complete all as specified and directed

S& F 75 mm CI soil waste and vent pipes single socketed in any length with or without ears, with cement joints on vertical surfaces of wall complete all as specified and directed.

Fixing only 75 mm bore CI pipe as on wall complete all as specified and directed.

S& F 75 mm CI bend, fixed with cement solvent complete, all as specified and directed

S& F 100 mm CI bend, fixed with cement solvent complete, all as specified and directed

Excavation in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes,sewage line pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in any type of soil, complete all as specified

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil, complete all as specified

M&L for removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M&L for walling of random rubble,uncoursed, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:6 complete all as specified & as directed.

M&L for 150mm dia SGSW drain pipes laid in trenches and jointed complete all as specified.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid with PCC 1:4:8 type D-2 for pipe of 150mm dia bore complete all as specified.

M&L for LLDPE Septic tank designed to carry sewage and sullage water , excavation in any type of soil In PCC 1:4:8 below foundation ,vent shaft ,connection, etc., complete for 25 users all as specifie and directed..

M&L Soakage wells exc, in ordinary Soil, foundation in PCC 1:3:6, wells of honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete of size 2.4 M dia X 3.0M deep, complete, all as specified and shown in drg No. CEBZ/TD/78/2011 Sheet 1/2 & 2/2.

Dismantling Asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified & directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws fixed with L & J hooks and washers, in roofs, walls etc with grade of zink coating 275 all as spd and directed

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed

M&L for 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Providing & Fixing false ceiling with Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge.

S&F Pressed steel door frame of size 105 x 60mm for doors with one or more rebates incl necessary fixing lugs hinges, lock strike plate, hold fasts etc.and filling PCC 1:3:6 type C-0 in frame, complete all as specified. ( Note: Quoted rates include cost of filling of PCC 1:3:6.type C-0 in door frame) complete all as specified and directed.

S&F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates incl necessary fixing lugs hinges, lock strike plate, hold fasts etc.and filling PCC 1:3:6 type C-0 in frame, complete all as specified. ( Note: Quoted rates include cost of filling of PCC 1:3:6.type C-0 in door frame) complete all as specified and directed.

S & F Flush shutters 30mm thick, solid core construction, with block board core and plywood face panels commercial type on both side and both facesis covered with approved pattern with Decorative coloured laminate type 1 of 0.9 mm thick and all around side faces covered with 10mm thick 1st class hard wood liping duly polished complete all as per specified and directed.

S&F 300mm ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F in repairs, 25mm dia stainless steel curtain rod heavy duty with a pair of decorative Curtain Finials/ knob & heavy Curtain Support Bracket for rod made of stainless steel, etc. complete all as specified & directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc.

Disconnecting unserviceable sub main wiring/service connection of any size and including steel conduit and accessories and removing from site and making good the disturbed surfaces.

Taking down MCB DB's/TPN complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for:-

One light point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board.

All as per item No.112.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor complete all as per specified and directed.

S&F switch piano flush type 5 amps, single pole one way 240 volts complete all as per specified and directed.

S&F switch piano flush type 15 amps, single pole one way 240 volts complete all as per specified and directed.

S&F Socket outlet 3 Pin 5/6 Amp flush type complete all as per specified and directed.

S&F socket out let 2 in 1, multipurpose 3 pin 15/16 Amp flush type ISI marked complete all as per specified and directed.

S&F ceiling fan regulator electronic flush , steped (four step) 230 Volts AC complete all as per specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17mm complete all as per specified and directed.

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

S&F LED tube light fitting in acrylic linear tube (1x 18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. Make:- Havells Cat part No PHOTONULTRA2.01212T8SSTL20WLED 865SPC (for tube) REGALBATTENT8UPTO1X22WDSBSWH (for batten)Bajaj Cat Part No BLRB 18W CWc for tube , BLRB - DB 118 for batten , or equivalent model of Philips/Crompton

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make Bajaj/Havells/CG

S & F LED light fitting 1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make Bajaj/Havells/CG

S&F testing and commissioning energy saving street light luminaire 35 watt LED , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete, IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge. Make- Havells Cat Part No ENDURACITYLITEPLAT PLUSSL35WLED757SASYBOPC or equivalent model of Surya/Control& Switchgear/Bajaj

S&F street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts for fixing of street light complete all as specified and directed by Engr-in-Charge.

S&F of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S&F of MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'C' curve complete all as specified and directed.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S&F exhaust fans AC single phase 230V of size 380mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. Make: havells/Crompton/Orient/Usha

S&F exhaust fans AC single phase 230V of size 450mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. Make: havells/Crompton/Orient/Usha

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing complete all as specified and directed.

M&L for submain wiring with two single core, PVC insulated, unsheathed, FRLS, 1100 volts grade 2.5 Sqmm multi stranded copper conductor cable drawn through and including 25 mm dia PVC non metallic rigid conduits & conduits accessories, concealed in wall/ roof/ ceiling ncluding one run of green colour earth continuity conductor with 2.5 Sqmm multi stranded copper conductor cable complete all as specified and directed. Note :- Two run of single core cable, one run of earth continuity conductor & conduit with conduit accessories shall be measured as one unit length.

S&F of LED lamp 9/10 watt complete all as specified and directed.

S&F ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BEE 5 star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy. Make: havells/Crompton/Orient/Usha

Taking down existing ceiling fan , dismantling blades and refixing after cleaning incl conecting up with three core flexible cable from ceiling rose to fan. complete all as specified & directed.

V K LAKWAL CONSTRUCTION

kirtiman traders

Shree Sai Ram Enterprises

M/s AKASH CONSTRUCTION CO.

M/s S. K. Construction Co.

M/S Nexus Projects

RISHU RISHANT CONSTRUCTION

M/s SUNIL ENTERPRISES

GOMA CONTRUCTION COMPANY